Hi Roger,
On Tue, 19 Apr 2016 13:28:50 +0300
Roger Quadros <rogerq@xxxxxx> wrote:
> > @@ -1921,6 +1927,9 @@ static int omap_nand_probe(struct platform_device *pdev)
> > nand_chip->ecc.correct = omap_correct_data;
> > mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
> > oobbytes_per_step = nand_chip->ecc.bytes;
> > +
> > + if (nand_chip->options & NAND_BUSWIDTH_16)
> > + min_oobbytes = 1;
>
> Shouldn't this have been
> if (!(nand_chip->options & NAND_BUSWIDTH_16)
> min_oobbytes = 1;
> ?
Yep.
>
> > break;
> >
> > case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
> > @@ -2038,10 +2047,8 @@ static int omap_nand_probe(struct platform_device *pdev)
> > }
> >
> > /* check if NAND device's OOB is enough to store ECC signatures */
> > - min_oobbytes = (oobbytes_per_step *
> > - (mtd->writesize / nand_chip->ecc.size)) +
> > - (nand_chip->options & NAND_BUSWIDTH_16 ?
> > - BADBLOCK_MARKER_LENGTH : 1);
> > + min_oobbytes += (oobbytes_per_step *
> > + (mtd->writesize / nand_chip->ecc.size));
> > if (mtd->oobsize < min_oobbytes) {
> > dev_err(&info->pdev->dev,
> > "not enough OOB bytes required = %d, available=%d\n",
> >
>
> After the above changes BCH with HW ECC worked fine but BCH with SW ECC still failed.
> I had to fix it up with the below patch. This is mainly because chip->ecc.steps wasn't
> yet initialized before calling nand_bch_init().
>
> After the below patch it worked fine with bch4 (hw & sw), bch8 (hw & sw) and ham1.
> I couldn't yet verify bch16 though.
Thanks for the fix, but I'd prefer fixing the bug for all soft BCH
users.
Could you try this patch?
--->8---
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/nand_bch.c
index ca9b2a4..3ca3d39 100644
--- a/drivers/mtd/nand/nand_bch.c
+++ b/drivers/mtd/nand/nand_bch.c
@@ -177,6 +177,16 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
goto fail;
}
+ /*
+ * ecc->steps and ecc->total might be used by mtd->ooblayout->ecc(),
+ * which is called by mtd_ooblayout_count_eccbytes().
+ * Make sure they are properly initialized before calling
+ * mtd_ooblayout_count_eccbytes().
+ * FIXME: we should probaly rework the sequencing in nand_scan_tail()
+ * to avoid setting those fields twice.
+ */
+ nand->ecc.steps = eccsteps;
+ nand->ecc.total = eccsteps * eccbytes;
if (mtd_ooblayout_count_eccbytes(mtd) != (eccsteps*eccbytes)) {
printk(KERN_WARNING "invalid ecc layout\n");
goto fail;
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
