Fix the checkpatch.pl issues:
CHECK: Logical continuations should be on the previous line
Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Ian Abbott <abbotti@xxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/staging/comedi/drivers/ni_mio_common.c | 17 ++++++++---------
1 file changed, 8 insertions(+), 9 deletions(-)
diff --git a/drivers/staging/comedi/drivers/ni_mio_common.c b/drivers/staging/comedi/drivers/ni_mio_common.c
index f5320f2..c56a518 100644
--- a/drivers/staging/comedi/drivers/ni_mio_common.c
+++ b/drivers/staging/comedi/drivers/ni_mio_common.c
@@ -925,9 +925,8 @@ static int ni_ai_drain_dma(struct comedi_device *dev)
if (devpriv->ai_mite_chan) {
for (i = 0; i < timeout; i++) {
if ((ni_stc_readw(dev, NISTC_AI_STATUS1_REG) &
- NISTC_AI_STATUS1_FIFO_E)
- && mite_bytes_in_transit(devpriv->ai_mite_chan) ==
- 0)
+ NISTC_AI_STATUS1_FIFO_E) &&
+ mite_bytes_in_transit(devpriv->ai_mite_chan) == 0)
break;
udelay(5);
}
@@ -1809,8 +1808,8 @@ static void ni_load_channelgain_list(struct comedi_device *dev,
return;
}
if (n_chan == 1 && !devpriv->is_611x && !devpriv->is_6143) {
- if (devpriv->changain_state
- && devpriv->changain_spec == list[0]) {
+ if (devpriv->changain_state &&
+ devpriv->changain_spec == list[0]) {
/* ready to go. */
return;
}
@@ -1824,8 +1823,8 @@ static void ni_load_channelgain_list(struct comedi_device *dev,
/* Set up Calibration mode if required */
if (devpriv->is_6143) {
- if ((list[0] & CR_ALT_SOURCE)
- && !devpriv->ai_calib_source_enabled) {
+ if ((list[0] & CR_ALT_SOURCE) &&
+ !devpriv->ai_calib_source_enabled) {
/* Strobe Relay enable bit */
ni_writew(dev, devpriv->ai_calib_source |
NI6143_CALIB_CHAN_RELAY_ON,
@@ -1835,8 +1834,8 @@ static void ni_load_channelgain_list(struct comedi_device *dev,
devpriv->ai_calib_source_enabled = 1;
/* Allow relays to change */
msleep_interruptible(100);
- } else if (!(list[0] & CR_ALT_SOURCE)
- && devpriv->ai_calib_source_enabled) {
+ } else if (!(list[0] & CR_ALT_SOURCE) &&
+ devpriv->ai_calib_source_enabled) {
/* Strobe Relay disable bit */
ni_writew(dev, devpriv->ai_calib_source |
NI6143_CALIB_CHAN_RELAY_OFF,
--
2.6.3
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
