Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>
---
drivers/mtd/nand/davinci_nand.c | 118 +++++++++++++++-------------------------
1 file changed, 44 insertions(+), 74 deletions(-)
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
index 8cb821b..fe3fd29 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/davinci_nand.c
@@ -54,7 +54,6 @@
*/
struct davinci_nand_info {
struct nand_chip chip;
- struct nand_ecclayout ecclayout;
struct device *dev;
struct clk *clk;
@@ -480,63 +479,46 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd)
* ten ECC bytes plus the manufacturer's bad block marker byte, and
* and not overlapping the default BBT markers.
*/
-static struct nand_ecclayout hwecc4_small = {
- .eccbytes = 10,
- .eccpos = { 0, 1, 2, 3, 4,
- /* offset 5 holds the badblock marker */
- 6, 7,
- 13, 14, 15, },
- .oobfree = {
- {.offset = 8, .length = 5, },
- {.offset = 16, },
- },
-};
+static int hwecc4_ooblayout_small_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ if (section > 2)
+ return -ERANGE;
+
+ if (!section) {
+ oobregion->offset = 0;
+ oobregion->length = 5;
+ } else if (section == 1) {
+ oobregion->offset = 6;
+ oobregion->length = 2;
+ } else {
+ oobregion->offset = 13;
+ oobregion->length = 3;
+ }
-/* An ECC layout for using 4-bit ECC with large-page (2048bytes) flash,
- * storing ten ECC bytes plus the manufacturer's bad block marker byte,
- * and not overlapping the default BBT markers.
- */
-static struct nand_ecclayout hwecc4_2048 = {
- .eccbytes = 40,
- .eccpos = {
- /* at the end of spare sector */
- 24, 25, 26, 27, 28, 29, 30, 31, 32, 33,
- 34, 35, 36, 37, 38, 39, 40, 41, 42, 43,
- 44, 45, 46, 47, 48, 49, 50, 51, 52, 53,
- 54, 55, 56, 57, 58, 59, 60, 61, 62, 63,
- },
- .oobfree = {
- /* 2 bytes at offset 0 hold manufacturer badblock markers */
- {.offset = 2, .length = 22, },
- /* 5 bytes at offset 8 hold BBT markers */
- /* 8 bytes at offset 16 hold JFFS2 clean markers */
- },
-};
+ return 0;
+}
-/*
- * An ECC layout for using 4-bit ECC with large-page (4096bytes) flash,
- * storing ten ECC bytes plus the manufacturer's bad block marker byte,
- * and not overlapping the default BBT markers.
- */
-static struct nand_ecclayout hwecc4_4096 = {
- .eccbytes = 80,
- .eccpos = {
- /* at the end of spare sector */
- 48, 49, 50, 51, 52, 53, 54, 55, 56, 57,
- 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
- 68, 69, 70, 71, 72, 73, 74, 75, 76, 77,
- 78, 79, 80, 81, 82, 83, 84, 85, 86, 87,
- 88, 89, 90, 91, 92, 93, 94, 95, 96, 97,
- 98, 99, 100, 101, 102, 103, 104, 105, 106, 107,
- 108, 109, 110, 111, 112, 113, 114, 115, 116, 117,
- 118, 119, 120, 121, 122, 123, 124, 125, 126, 127,
- },
- .oobfree = {
- /* 2 bytes at offset 0 hold manufacturer badblock markers */
- {.offset = 2, .length = 46, },
- /* 5 bytes at offset 8 hold BBT markers */
- /* 8 bytes at offset 16 hold JFFS2 clean markers */
- },
+static int hwecc4_ooblayout_small_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobregion)
+{
+ if (section > 1)
+ return -ERANGE;
+
+ if (!section) {
+ oobregion->offset = 8;
+ oobregion->length = 5;
+ } else {
+ oobregion->offset = 16;
+ oobregion->length = mtd->oobsize - 16;
+ }
+
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops hwecc4_small_ooblayout_ops = {
+ .ecc = hwecc4_ooblayout_small_ecc,
+ .free = hwecc4_ooblayout_small_free,
};
#if defined(CONFIG_OF)
@@ -805,26 +787,14 @@ static int nand_davinci_probe(struct platform_device *pdev)
* table marker fits in the free bytes.
*/
if (chunks == 1) {
- info->ecclayout = hwecc4_small;
- info->ecclayout.oobfree[1].length = mtd->oobsize - 16;
- goto syndrome_done;
- }
- if (chunks == 4) {
- info->ecclayout = hwecc4_2048;
+ mtd_set_ooblayout(mtd, &hwecc4_small_ooblayout_ops);
+ } else if (chunks == 4 || chunks == 8) {
+ mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops);
info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
- goto syndrome_done;
- }
- if (chunks == 8) {
- info->ecclayout = hwecc4_4096;
- info->chip.ecc.mode = NAND_ECC_HW_OOB_FIRST;
- goto syndrome_done;
+ } else {
+ ret = -EIO;
+ goto err;
}
-
- ret = -EIO;
- goto err;
-
-syndrome_done:
- info->chip.ecc.layout = &info->ecclayout;
}
ret = nand_scan_tail(mtd);
--
2.1.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
