This patch implements ni_ao_cmd much more closely organized like NI MHDDK
examples and DAQ-STC pseudo-code. Adds comments with some more specific
references to the DAQ-STC.
For stop_src==TRIG_NONE (continuous output mode of entire buffer), the
count for the UC counter was corrected to represent the maximum count
possible (0xffffff). Prior behavior for stop_src=TRIG_NONE did not
actually follow the DAQ-STC. Furthermore, stop_src==TRIG_NONE now
correctly uses code specialized for either m-series or e-series devices.
It should be noted that stop_src==TRIG_NONE does _not_ with this patch
(or with prior behavior in ni_mio_common) actually implement true
continuous output. Rather, the output is simply configured to operate as a
single buffer output, but where the buffer is as large as is possible with
NI-STC hardware.
Signed-off-by: Spencer E. Olson <olsonse@xxxxxxxxx>
---
drivers/staging/comedi/drivers/ni_mio_common.c | 443 ++++++++++++++++++-------
1 file changed, 318 insertions(+), 125 deletions(-)
diff --git a/drivers/staging/comedi/drivers/ni_mio_common.c b/drivers/staging/comedi/drivers/ni_mio_common.c
index 7dc12a4..4e7a01c 100644
--- a/drivers/staging/comedi/drivers/ni_mio_common.c
+++ b/drivers/staging/comedi/drivers/ni_mio_common.c
@@ -2887,42 +2887,68 @@ static int ni_ao_inttrig(struct comedi_device *dev,
return 0;
}
-static int ni_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
+/*
+ * begin ni_ao_cmd.
+ * Organized similar to NI-STC and MHDDK examples.
+ * ni_ao_cmd is broken out into configuration sub-routines for clarity.
+ */
+
+static void ni_ao_cmd_personalize(struct comedi_device *dev,
+ const struct comedi_cmd *cmd)
{
const struct ni_board_struct *board = dev->board_ptr;
- struct ni_private *devpriv = dev->private;
- const struct comedi_cmd *cmd = &s->async->cmd;
- int bits;
- int i;
- unsigned trigvar;
- unsigned val;
-
- if (dev->irq == 0) {
- dev_err(dev->class_dev, "cannot run command without an irq\n");
- return -EIO;
- }
+ unsigned bits;
ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
- ni_stc_writew(dev, NISTC_AO_CMD1_DISARM, NISTC_AO_CMD1_REG);
+ bits =
+ /* fast CPU interface--only eseries */
+ /* ((slow CPU interface) ? 0 : AO_Fast_CPU) | */
+ NISTC_AO_PERSONAL_BC_SRC_SEL |
+ 0 /* (use_original_pulse ? 0 : NISTC_AO_PERSONAL_UPDATE_TIMEBASE) */ |
+ /*
+ * FIXME: start setting following bit when appropriate. Need to
+ * determine whether board is E4 or E1.
+ * FROM MHHDK:
+ * if board is E4 or E1
+ * Set bit "NISTC_AO_PERSONAL_UPDATE_PW" to 0
+ * else
+ * set it to 1
+ */
+ NISTC_AO_PERSONAL_UPDATE_PW |
+ /* FIXME: when should we set following bit to zero? */
+ NISTC_AO_PERSONAL_TMRDACWR_PW |
+ (board->ao_fifo_depth ?
+ NISTC_AO_PERSONAL_FIFO_ENA : NISTC_AO_PERSONAL_DMA_PIO_CTRL)
+ ;
+#if 0
+ /*
+ * FIXME:
+ * add something like ".has_individual_dacs = 0" to ni_board_struct
+ * since, as F Hess pointed out, not all in m series have singles. not
+ * sure if e-series all have duals...
+ */
- if (devpriv->is_6xxx) {
- ni_ao_win_outw(dev, NI611X_AO_MISC_CLEAR_WG,
- NI611X_AO_MISC_REG);
+ /*
+ * F Hess: windows driver does not set NISTC_AO_PERSONAL_NUM_DAC bit for
+ * 6281, verified with bus analyzer.
+ */
+ if (devpriv->is_m_series)
+ bits |= NISTC_AO_PERSONAL_NUM_DAC;
+#endif
+ ni_stc_writew(dev, bits, NISTC_AO_PERSONAL_REG);
- bits = 0;
- for (i = 0; i < cmd->chanlist_len; i++) {
- int chan;
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
- chan = CR_CHAN(cmd->chanlist[i]);
- bits |= 1 << chan;
- ni_ao_win_outw(dev, chan, NI611X_AO_WAVEFORM_GEN_REG);
- }
- ni_ao_win_outw(dev, bits, NI611X_AO_TIMED_REG);
- }
+static void ni_ao_cmd_set_trigger(struct comedi_device *dev,
+ const struct comedi_cmd *cmd)
+{
+ struct ni_private *devpriv = dev->private;
- ni_ao_config_chanlist(dev, s, cmd->chanlist, cmd->chanlist_len, 1);
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
+ /* sync */
if (cmd->stop_src == TRIG_NONE) {
devpriv->ao_mode1 |= NISTC_AO_MODE1_CONTINUOUS;
devpriv->ao_mode1 &= ~NISTC_AO_MODE1_TRIGGER_ONCE;
@@ -2932,179 +2958,346 @@ static int ni_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
}
ni_stc_writew(dev, devpriv->ao_mode1, NISTC_AO_MODE1_REG);
- val = devpriv->ao_trigger_select;
- switch (cmd->start_src) {
- case TRIG_INT:
- case TRIG_NOW:
- val &= ~(NISTC_AO_TRIG_START1_POLARITY |
- NISTC_AO_TRIG_START1_SEL_MASK);
- val |= NISTC_AO_TRIG_START1_EDGE |
- NISTC_AO_TRIG_START1_SYNC;
- break;
- case TRIG_EXT:
- val = NISTC_AO_TRIG_START1_SEL(CR_CHAN(cmd->start_arg) + 1);
- if (cmd->start_arg & CR_INVERT) {
- /* 0=active high, 1=active low. see daq-stc 3-24 (p186) */
- val |= NISTC_AO_TRIG_START1_POLARITY;
- }
- if (cmd->start_arg & CR_EDGE) {
- /* 0=edge detection disabled, 1=enabled */
- val |= NISTC_AO_TRIG_START1_EDGE;
+ {
+ unsigned int trigsel = devpriv->ao_trigger_select;
+
+ switch (cmd->start_src) {
+ case TRIG_INT:
+ case TRIG_NOW:
+ trigsel &= ~(NISTC_AO_TRIG_START1_POLARITY |
+ NISTC_AO_TRIG_START1_SEL_MASK);
+ trigsel |= NISTC_AO_TRIG_START1_EDGE |
+ NISTC_AO_TRIG_START1_SYNC;
+ break;
+ case TRIG_EXT:
+ trigsel = NISTC_AO_TRIG_START1_SEL(
+ CR_CHAN(cmd->start_arg) + 1);
+ if (cmd->start_arg & CR_INVERT)
+ /*
+ * 0=active high, 1=active low.
+ * see daq-stc 3-24 (p186)
+ */
+ trigsel |= NISTC_AO_TRIG_START1_POLARITY;
+ if (cmd->start_arg & CR_EDGE)
+ /* 0=edge detection disabled, 1=enabled */
+ trigsel |= NISTC_AO_TRIG_START1_EDGE;
+ break;
+ default:
+ BUG();
+ break;
}
+
+ devpriv->ao_trigger_select = trigsel;
ni_stc_writew(dev, devpriv->ao_trigger_select,
NISTC_AO_TRIG_SEL_REG);
- break;
- default:
- BUG();
- break;
}
- devpriv->ao_trigger_select = val;
- ni_stc_writew(dev, devpriv->ao_trigger_select, NISTC_AO_TRIG_SEL_REG);
+ /* AO_Delayed_START1 = 0, we do not support delayed start...yet */
+ /* sync */
+ /* select DA_START1 as PFI6/AO_START1 when configured as an output */
devpriv->ao_mode3 &= ~NISTC_AO_MODE3_TRIG_LEN;
ni_stc_writew(dev, devpriv->ao_mode3, NISTC_AO_MODE3_REG);
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
+
+static void ni_ao_cmd_set_counters(struct comedi_device *dev,
+ const struct comedi_cmd *cmd)
+{
+ struct ni_private *devpriv = dev->private;
+ /* Not supporting 'waveform staging' or 'local buffer with pauses' */
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
+ /*
+ * This relies on ao_mode1/(Trigger_Once | Continuous) being set in
+ * set_trigger above. It is unclear whether we really need to re-write
+ * this register with these values. The mhddk examples for e-series
+ * show writing this in both places, but the examples for m-series show
+ * a single write in the set_counters function (here).
+ */
ni_stc_writew(dev, devpriv->ao_mode1, NISTC_AO_MODE1_REG);
+
+ /* sync (upload number of buffer iterations -1) */
+ /* indicate that we want to use BC_Load_A_Register as the source */
devpriv->ao_mode2 &= ~NISTC_AO_MODE2_BC_INIT_LOAD_SRC;
ni_stc_writew(dev, devpriv->ao_mode2, NISTC_AO_MODE2_REG);
- if (cmd->stop_src == TRIG_NONE)
- ni_stc_writel(dev, 0xffffff, NISTC_AO_BC_LOADA_REG);
- else
- ni_stc_writel(dev, 0, NISTC_AO_BC_LOADA_REG);
+
+ /*
+ * if the BC_TC interrupt is still issued in spite of UC, BC, UI
+ * ignoring BC_TC, then we will need to find a way to ignore that
+ * interrupt in continuous mode.
+ */
+ ni_stc_writel(dev, 0, NISTC_AO_BC_LOADA_REG); /* iter once */
+
+ /* sync (issue command to load number of buffer iterations -1) */
ni_stc_writew(dev, NISTC_AO_CMD1_BC_LOAD, NISTC_AO_CMD1_REG);
+
+ /* sync (upload number of updates in buffer) */
+ /* indicate that we want to use UC_Load_A_Register as the source */
devpriv->ao_mode2 &= ~NISTC_AO_MODE2_UC_INIT_LOAD_SRC;
ni_stc_writew(dev, devpriv->ao_mode2, NISTC_AO_MODE2_REG);
- switch (cmd->stop_src) {
- case TRIG_COUNT:
+
+ {
+ /*
+ * Current behavior is to configure the maximum update count
+ * possible when continuous output mode is requested.
+ */
+ unsigned int stop_arg = cmd->stop_src == TRIG_COUNT ?
+ (cmd->stop_arg & 0xffffff) : 0xffffff;
+
if (devpriv->is_m_series) {
- /* this is how the NI example code does it for m-series boards, verified correct with 6259 */
- ni_stc_writel(dev, cmd->stop_arg - 1,
- NISTC_AO_UC_LOADA_REG);
+ /*
+ * this is how the NI example code does it for m-series
+ * boards, verified correct with 6259
+ */
+ ni_stc_writel(dev, stop_arg - 1, NISTC_AO_UC_LOADA_REG);
+
+ /* sync (issue cmd to load number of updates in MISB) */
ni_stc_writew(dev, NISTC_AO_CMD1_UC_LOAD,
NISTC_AO_CMD1_REG);
} else {
- ni_stc_writel(dev, cmd->stop_arg,
- NISTC_AO_UC_LOADA_REG);
+ ni_stc_writel(dev, stop_arg, NISTC_AO_UC_LOADA_REG);
+
+ /* sync (issue cmd to load number of updates in MISB) */
ni_stc_writew(dev, NISTC_AO_CMD1_UC_LOAD,
NISTC_AO_CMD1_REG);
- ni_stc_writel(dev, cmd->stop_arg - 1,
- NISTC_AO_UC_LOADA_REG);
+
+ /*
+ * sync (upload number of updates-1 in MISB)
+ * --eseries only?
+ */
+ ni_stc_writel(dev, stop_arg - 1, NISTC_AO_UC_LOADA_REG);
}
- break;
- case TRIG_NONE:
- ni_stc_writel(dev, 0xffffff, NISTC_AO_UC_LOADA_REG);
- ni_stc_writew(dev, NISTC_AO_CMD1_UC_LOAD, NISTC_AO_CMD1_REG);
- ni_stc_writel(dev, 0xffffff, NISTC_AO_UC_LOADA_REG);
- break;
- default:
- ni_stc_writel(dev, 0, NISTC_AO_UC_LOADA_REG);
- ni_stc_writew(dev, NISTC_AO_CMD1_UC_LOAD, NISTC_AO_CMD1_REG);
- ni_stc_writel(dev, cmd->stop_arg, NISTC_AO_UC_LOADA_REG);
}
- devpriv->ao_mode1 &= ~(NISTC_AO_MODE1_UPDATE_SRC_MASK |
- NISTC_AO_MODE1_UI_SRC_MASK |
- NISTC_AO_MODE1_UPDATE_SRC_POLARITY |
- NISTC_AO_MODE1_UI_SRC_POLARITY);
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
+
+static void ni_ao_cmd_set_update(struct comedi_device *dev,
+ const struct comedi_cmd *cmd)
+{
+ struct ni_private *devpriv = dev->private;
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
+
+ /*
+ * zero out these bit fields to be set below. Does an ao-reset do this
+ * automatically?
+ */
+ devpriv->ao_mode1 &= ~(
+ NISTC_AO_MODE1_UI_SRC_MASK |
+ NISTC_AO_MODE1_UI_SRC_POLARITY |
+ NISTC_AO_MODE1_UPDATE_SRC_MASK |
+ NISTC_AO_MODE1_UPDATE_SRC_POLARITY
+ );
+
switch (cmd->scan_begin_src) {
case TRIG_TIMER:
- devpriv->ao_cmd2 &= ~NISTC_AO_CMD2_BC_GATE_ENA;
- trigvar =
- ni_ns_to_timer(dev, cmd->scan_begin_arg,
- CMDF_ROUND_NEAREST);
- ni_stc_writel(dev, 1, NISTC_AO_UI_LOADA_REG);
- ni_stc_writew(dev, NISTC_AO_CMD1_UI_LOAD, NISTC_AO_CMD1_REG);
- ni_stc_writel(dev, trigvar, NISTC_AO_UI_LOADA_REG);
+ devpriv->ao_cmd2 &= ~NISTC_AO_CMD2_BC_GATE_ENA;
+
+ /*
+ * NOTE: there are several other ways of configuring internal
+ * updates, but we'll only support one for now: using
+ * AO_IN_TIMEBASE, w/o waveform staging, w/o a delay between
+ * START1 and first update, and also w/o local buffer mode w/
+ * pauses.
+ */
+
+ /*
+ * This is already done above:
+ * devpriv->ao_mode1 &= ~(
+ * // set UPDATE_Source to UI_TC:
+ * NISTC_AO_MODE1_UPDATE_SRC_MASK |
+ * // set UPDATE_Source_Polarity to rising (required?)
+ * NISTC_AO_MODE1_UPDATE_SRC_POLARITY |
+ * // set UI_Source to AO_IN_TIMEBASE1:
+ * NISTC_AO_MODE1_UI_SRC_MASK |
+ * // set UI_Source_Polarity to rising (required?)
+ * NISTC_AO_MODE1_UI_SRC_POLARITY
+ * );
+ */
+
+ /*
+ * TODO: use ao_ui_clock_source to allow all possible signals
+ * to be routed to UI_Source_Select. See tSTC.h for
+ * eseries/ni67xx and tMSeries.h for mseries.
+ */
+
+ {
+ unsigned trigvar = ni_ns_to_timer(dev,
+ cmd->scan_begin_arg,
+ CMDF_ROUND_NEAREST);
+
+ /*
+ * Wait N TB3 ticks after the start trigger before
+ * clocking(N must be >=2).
+ */
+ /* following line: 2-1 per STC */
+ ni_stc_writel(dev, 1, NISTC_AO_UI_LOADA_REG);
+ ni_stc_writew(dev, NISTC_AO_CMD1_UI_LOAD,
+ NISTC_AO_CMD1_REG);
+ /* following line: N-1 per STC */
+ ni_stc_writel(dev, trigvar - 1, NISTC_AO_UI_LOADA_REG);
+ }
break;
case TRIG_EXT:
- devpriv->ao_mode1 |=
- NISTC_AO_MODE1_UPDATE_SRC(cmd->scan_begin_arg);
+ /* FIXME: assert scan_begin_arg != 0, ret failure otherwise */
+ devpriv->ao_cmd2 |= NISTC_AO_CMD2_BC_GATE_ENA;
+ devpriv->ao_mode1 |= NISTC_AO_MODE1_UPDATE_SRC(
+ CR_CHAN(cmd->scan_begin_arg));
if (cmd->scan_begin_arg & CR_INVERT)
devpriv->ao_mode1 |= NISTC_AO_MODE1_UPDATE_SRC_POLARITY;
- devpriv->ao_cmd2 |= NISTC_AO_CMD2_BC_GATE_ENA;
break;
default:
BUG();
break;
}
+
ni_stc_writew(dev, devpriv->ao_cmd2, NISTC_AO_CMD2_REG);
ni_stc_writew(dev, devpriv->ao_mode1, NISTC_AO_MODE1_REG);
devpriv->ao_mode2 &= ~(NISTC_AO_MODE2_UI_RELOAD_MODE(3) |
NISTC_AO_MODE2_UI_INIT_LOAD_SRC);
ni_stc_writew(dev, devpriv->ao_mode2, NISTC_AO_MODE2_REG);
+ /* Configure DAQ-STC for Timed update mode */
+ devpriv->ao_cmd1 |= NISTC_AO_CMD1_DAC1_UPDATE_MODE |
+ NISTC_AO_CMD1_DAC0_UPDATE_MODE;
+ /* We are not using UPDATE2-->don't have to set DACx_Source_Select */
+ ni_stc_writew(dev, devpriv->ao_cmd1, NISTC_AO_CMD1_REG);
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
+
+static void ni_ao_cmd_set_channels(struct comedi_device *dev,
+ struct comedi_subdevice *s)
+{
+ struct ni_private *devpriv = dev->private;
+ const struct comedi_cmd *cmd = &s->async->cmd;
+ unsigned bits = 0;
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
+
+ if (devpriv->is_6xxx) {
+ unsigned int i;
+
+ bits = 0;
+ for (i = 0; i < cmd->chanlist_len; ++i) {
+ int chan = CR_CHAN(cmd->chanlist[i]);
+
+ bits |= 1 << chan;
+ ni_ao_win_outw(dev, chan, NI611X_AO_WAVEFORM_GEN_REG);
+ }
+ ni_ao_win_outw(dev, bits, NI611X_AO_TIMED_REG);
+ }
+
+ ni_ao_config_chanlist(dev, s, cmd->chanlist, cmd->chanlist_len, 1);
+
if (cmd->scan_end_arg > 1) {
devpriv->ao_mode1 |= NISTC_AO_MODE1_MULTI_CHAN;
- ni_stc_writew(dev,
- NISTC_AO_OUT_CTRL_CHANS(cmd->scan_end_arg - 1) |
- NISTC_AO_OUT_CTRL_UPDATE_SEL_HIGHZ,
- NISTC_AO_OUT_CTRL_REG);
- } else {
- unsigned bits;
+ bits = NISTC_AO_OUT_CTRL_CHANS(cmd->scan_end_arg - 1)
+ | NISTC_AO_OUT_CTRL_UPDATE_SEL_HIGHZ;
+ } else {
devpriv->ao_mode1 &= ~NISTC_AO_MODE1_MULTI_CHAN;
bits = NISTC_AO_OUT_CTRL_UPDATE_SEL_HIGHZ;
- if (devpriv->is_m_series || devpriv->is_6xxx) {
+ if (devpriv->is_m_series | devpriv->is_6xxx)
bits |= NISTC_AO_OUT_CTRL_CHANS(0);
- } else {
- bits |=
- NISTC_AO_OUT_CTRL_CHANS(CR_CHAN(cmd->chanlist[0]));
- }
- ni_stc_writew(dev, bits, NISTC_AO_OUT_CTRL_REG);
+ else
+ bits |= NISTC_AO_OUT_CTRL_CHANS(
+ CR_CHAN(cmd->chanlist[0]));
}
+
ni_stc_writew(dev, devpriv->ao_mode1, NISTC_AO_MODE1_REG);
+ ni_stc_writew(dev, bits, NISTC_AO_OUT_CTRL_REG);
- /* Configure DAQ-STC for Timed update mode */
- devpriv->ao_cmd1 |= NISTC_AO_CMD1_DAC1_UPDATE_MODE |
- NISTC_AO_CMD1_DAC0_UPDATE_MODE;
- /* We are not using UPDATE2-->don't have to set DACx_Source_Select */
- ni_stc_writew(dev, devpriv->ao_cmd1, NISTC_AO_CMD1_REG);
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
+
+static void ni_ao_cmd_set_stop_conditions(struct comedi_device *dev,
+ const struct comedi_cmd *cmd)
+{
+ struct ni_private *devpriv = dev->private;
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
devpriv->ao_mode3 |= NISTC_AO_MODE3_STOP_ON_OVERRUN_ERR;
ni_stc_writew(dev, devpriv->ao_mode3, NISTC_AO_MODE3_REG);
+ /*
+ * Since we are not supporting waveform staging, we ignore these errors:
+ * NISTC_AO_MODE3_STOP_ON_BC_TC_ERR,
+ * NISTC_AO_MODE3_STOP_ON_BC_TC_TRIG_ERR
+ */
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
+}
+
+static void ni_ao_cmd_set_fifo_mode(struct comedi_device *dev)
+{
+ struct ni_private *devpriv = dev->private;
+
+ ni_stc_writew(dev, NISTC_RESET_AO_CFG_START, NISTC_RESET_REG);
+
devpriv->ao_mode2 &= ~NISTC_AO_MODE2_FIFO_MODE_MASK;
#ifdef PCIDMA
devpriv->ao_mode2 |= NISTC_AO_MODE2_FIFO_MODE_HF_F;
#else
devpriv->ao_mode2 |= NISTC_AO_MODE2_FIFO_MODE_HF;
#endif
+ /* NOTE: this is where use_onboard_memory=True would be implemented */
devpriv->ao_mode2 &= ~NISTC_AO_MODE2_FIFO_REXMIT_ENA;
ni_stc_writew(dev, devpriv->ao_mode2, NISTC_AO_MODE2_REG);
- bits = NISTC_AO_PERSONAL_BC_SRC_SEL |
- NISTC_AO_PERSONAL_UPDATE_PW |
- NISTC_AO_PERSONAL_TMRDACWR_PW;
- if (board->ao_fifo_depth)
- bits |= NISTC_AO_PERSONAL_FIFO_ENA;
- else
- bits |= NISTC_AO_PERSONAL_DMA_PIO_CTRL;
-#if 0
- /*
- * F Hess: windows driver does not set NISTC_AO_PERSONAL_NUM_DAC bit
- * for 6281, verified with bus analyzer.
- */
- if (devpriv->is_m_series)
- bits |= NISTC_AO_PERSONAL_NUM_DAC;
-#endif
- ni_stc_writew(dev, bits, NISTC_AO_PERSONAL_REG);
- /* enable sending of ao dma requests */
+ /* enable sending of ao fifo requests (dma request) */
ni_stc_writew(dev, NISTC_AO_START_AOFREQ_ENA, NISTC_AO_START_SEL_REG);
ni_stc_writew(dev, NISTC_RESET_AO_CFG_END, NISTC_RESET_REG);
- if (cmd->stop_src == TRIG_COUNT) {
- ni_stc_writew(dev, NISTC_INTB_ACK_AO_BC_TC,
- NISTC_INTB_ACK_REG);
+ /* we are not supporting boards with virtual fifos */
+}
+
+static void ni_ao_cmd_set_interrupts(struct comedi_device *dev,
+ struct comedi_subdevice *s)
+{
+ if (s->async->cmd.stop_src == TRIG_COUNT)
ni_set_bits(dev, NISTC_INTB_ENA_REG,
NISTC_INTB_ENA_AO_BC_TC, 1);
- }
s->async->inttrig = ni_ao_inttrig;
+}
+static int ni_ao_cmd(struct comedi_device *dev, struct comedi_subdevice *s)
+{
+ struct ni_private *devpriv = dev->private;
+ const struct comedi_cmd *cmd = &s->async->cmd;
+
+ if (dev->irq == 0) {
+ dev_err(dev->class_dev, "cannot run command without an irq");
+ return -EIO;
+ }
+
+ /* ni_ao_reset should have already been done */
+ ni_ao_cmd_personalize(dev, cmd);
+ /* clearing fifo and preload happens elsewhere */
+
+ ni_ao_cmd_set_trigger(dev, cmd);
+ ni_ao_cmd_set_counters(dev, cmd);
+ ni_ao_cmd_set_update(dev, cmd);
+ ni_ao_cmd_set_channels(dev, s);
+ ni_ao_cmd_set_stop_conditions(dev, cmd);
+ ni_ao_cmd_set_fifo_mode(dev);
+ ni_ao_cmd_set_interrupts(dev, s);
+
+ /*
+ * arm(ing) and star(ting) happen in ni_ao_inttrig, which _must_ be
+ * called for ao commands since 1) TRIG_NOW is not supported and 2) DMA
+ * must be setup and initially written to before arm/start happen.
+ */
return 0;
}
+/* end ni_ao_cmd */
+
static int ni_ao_cmdtest(struct comedi_device *dev, struct comedi_subdevice *s,
struct comedi_cmd *cmd)
{
--
1.9.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
