This patch fixes:
1.Fixes comments that are over 80-characters either by:
-breaking up comment lines, into multi-line comments (kernel style) or
-shortening comments (Done in 7 places):
- Changed "Why?Becuz" to "Since" (6 places)
- Removed the comment "Which I dont care about" (1 place)
2.Fixes code lines that are over 80-characters by
-breaking up long math lines
-breaking up long function calls
2.Spelling errors in comments.
-tho -> though
-baudrate -> baud rate
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@xxxxxxxxx>
---
drivers/staging/dgnc/dgnc_neo.c | 189 +++++++++++++++++++++++++++-------------
1 file changed, 130 insertions(+), 59 deletions(-)
diff --git a/drivers/staging/dgnc/dgnc_neo.c b/drivers/staging/dgnc/dgnc_neo.c
index 900e3ae..174a69f 100644
--- a/drivers/staging/dgnc/dgnc_neo.c
+++ b/drivers/staging/dgnc/dgnc_neo.c
@@ -79,7 +79,8 @@ struct board_ops dgnc_neo_ops = {
.send_immediate_char = neo_send_immediate_char
};
-static uint dgnc_offset_table[8] = { 0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80 };
+static uint dgnc_offset_table[8] = { 0x01, 0x02, 0x04, 0x08,
+ 0x10, 0x20, 0x40, 0x80 };
/*
@@ -113,14 +114,15 @@ static inline void neo_set_cts_flow_control(struct channel_t *ch)
/* Turn off auto Xon flow control */
efr &= ~UART_17158_EFR_IXON;
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
/* Turn on table D, with 8 char hi/low watermarks */
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY),
+ &ch->ch_neo_uart->fctr);
/* Feed the UART our trigger levels */
writeb(8, &ch->ch_neo_uart->tfifo);
@@ -149,13 +151,14 @@ static inline void neo_set_rts_flow_control(struct channel_t *ch)
ier &= ~UART_17158_IER_XOFF;
efr &= ~UART_17158_EFR_IXOFF;
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_4DELAY),
+ &ch->ch_neo_uart->fctr);
ch->ch_r_watermark = 4;
writeb(32, &ch->ch_neo_uart->rfifo);
@@ -187,13 +190,14 @@ static inline void neo_set_ixon_flow_control(struct channel_t *ch)
/* Turn on auto Xon flow control */
efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXON);
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY),
+ &ch->ch_neo_uart->fctr);
ch->ch_r_watermark = 4;
writeb(32, &ch->ch_neo_uart->rfifo);
@@ -225,14 +229,15 @@ static inline void neo_set_ixoff_flow_control(struct channel_t *ch)
ier |= UART_17158_IER_XOFF;
efr |= (UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
/* Turn on table D, with 8 char hi/low watermarks */
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY),
+ &ch->ch_neo_uart->fctr);
writeb(8, &ch->ch_neo_uart->tfifo);
ch->ch_t_tlevel = 8;
@@ -267,14 +272,15 @@ static inline void neo_set_no_input_flow_control(struct channel_t *ch)
efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXOFF);
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
/* Turn on table D, with 8 char hi/low watermarks */
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY),
+ &ch->ch_neo_uart->fctr);
ch->ch_r_watermark = 0;
@@ -305,14 +311,15 @@ static inline void neo_set_no_output_flow_control(struct channel_t *ch)
else
efr &= ~(UART_17158_EFR_ECB | UART_17158_EFR_IXON);
- /* Why? Becuz Exar's spec says we have to zero it out before setting it */
+ /* Since Exar's spec says we have to zero it out before setting it */
writeb(0, &ch->ch_neo_uart->efr);
/* Turn on UART enhanced bits */
writeb(efr, &ch->ch_neo_uart->efr);
/* Turn on table D, with 8 char hi/low watermarks */
- writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY), &ch->ch_neo_uart->fctr);
+ writeb((UART_17158_FCTR_TRGD | UART_17158_FCTR_RTS_8DELAY),
+ &ch->ch_neo_uart->fctr);
ch->ch_r_watermark = 0;
@@ -333,7 +340,8 @@ static inline void neo_set_new_start_stop_chars(struct channel_t *ch)
{
/* if hardware flow control is set, then skip this whole thing */
- if (ch->ch_digi.digi_flags & (CTSPACE | RTSPACE) || ch->ch_c_cflag & CRTSCTS)
+ if (ch->ch_digi.digi_flags & (CTSPACE | RTSPACE) ||
+ ch->ch_c_cflag & CRTSCTS)
return;
/* Tell UART what start/stop chars it should be looking for */
@@ -408,7 +416,8 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
break;
/*
- * Yank off the upper 2 bits, which just show that the FIFO's are enabled.
+ * Yank off the upper 2 bits,
+ * which just show that the FIFO's are enabled.
*/
isr &= ~(UART_17158_IIR_FIFO_ENABLED);
@@ -418,7 +427,10 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
ch->ch_intr_rx++;
neo_copy_data_from_uart_to_queue(ch);
- /* Call our tty layer to enforce queue flow control if needed. */
+ /*
+ * Call our tty layer to
+ * enforce queue flow control if needed.
+ */
spin_lock_irqsave(&ch->ch_lock, flags);
dgnc_check_queue_flow_control(ch);
spin_unlock_irqrestore(&ch->ch_lock, flags);
@@ -443,7 +455,10 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
* one it was, so we can suspend or resume data flow.
*/
if (cause == UART_17158_XON_DETECT) {
- /* Is output stopped right now, if so, resume it */
+ /*
+ * Is output stopped right now,
+ * if so, resume it
+ */
if (brd->channels[port]->ch_flags & CH_STOP) {
spin_lock_irqsave(&ch->ch_lock,
flags);
@@ -452,7 +467,8 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
flags);
}
} else if (cause == UART_17158_XOFF_DETECT) {
- if (!(brd->channels[port]->ch_flags & CH_STOP)) {
+ if (!(brd->channels[port]->ch_flags &
+ CH_STOP)) {
spin_lock_irqsave(&ch->ch_lock,
flags);
ch->ch_flags |= CH_STOP;
@@ -464,8 +480,10 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
if (isr & UART_17158_IIR_HWFLOW_STATE_CHANGE) {
/*
- * If we get here, this means the hardware is doing auto flow control.
- * Check to see whether RTS/DTR or CTS/DSR caused this interrupt.
+ * If we get here,
+ * this means the hardware is doing auto flow control.
+ * Check to see whether RTS/DTR or CTS/DSR
+ * caused this interrupt.
*/
brd->intr_modem++;
ch->ch_intr_modem++;
@@ -561,7 +579,8 @@ static inline void neo_parse_lsr(struct dgnc_board *brd, uint port)
* Rx Oruns. Exar says that an orun will NOT corrupt
* the FIFO. It will just replace the holding register
* with this new data byte. So basically just ignore this.
- * Probably we should eventually have an orun stat in our driver...
+ * Probably we should eventually
+ * have an orun stat in our driver...
*/
ch->ch_err_overrun++;
}
@@ -633,7 +652,7 @@ static void neo_param(struct tty_struct *tty)
neo_flush_uart_write(ch);
neo_flush_uart_read(ch);
- /* The baudrate is B0 so all modem lines are to be dropped. */
+ /* The baud rate is B0 so all modem lines are to be dropped. */
ch->ch_flags |= (CH_BAUD0);
ch->ch_mostat &= ~(UART_MCR_RTS | UART_MCR_DTR);
neo_assert_modem_signals(ch);
@@ -683,8 +702,12 @@ static void neo_param(struct tty_struct *tty)
4800, 9600, 19200, 38400 }
};
- /* Only use the TXPrint baud rate if the terminal unit is NOT open */
- if (!(ch->ch_tun.un_flags & UN_ISOPEN) && (un->un_type == DGNC_PRINT))
+ /*
+ * Only use the TXPrint baud rate
+ * if the terminal unit is NOT open
+ */
+ if (!(ch->ch_tun.un_flags & UN_ISOPEN) &&
+ (un->un_type == DGNC_PRINT))
baud = C_BAUD(ch->ch_pun.un_tty) & 0xff;
else
baud = C_BAUD(ch->ch_tun.un_tty) & 0xff;
@@ -697,7 +720,8 @@ static void neo_param(struct tty_struct *tty)
jindex = baud;
- if ((iindex >= 0) && (iindex < 4) && (jindex >= 0) && (jindex < 16))
+ if ((iindex >= 0) && (iindex < 4) &&
+ (jindex >= 0) && (jindex < 16))
baud = bauds[iindex][jindex];
else
baud = 0;
@@ -804,8 +828,12 @@ static void neo_param(struct tty_struct *tty)
if (ch->ch_digi.digi_flags & CTSPACE || ch->ch_c_cflag & CRTSCTS) {
neo_set_cts_flow_control(ch);
} else if (ch->ch_c_iflag & IXON) {
- /* If start/stop is set to disable, then we should disable flow control */
- if ((ch->ch_startc == _POSIX_VDISABLE) || (ch->ch_stopc == _POSIX_VDISABLE))
+ /*
+ * If start/stop is set to disable,
+ * then we should disable flow control
+ */
+ if ((ch->ch_startc == _POSIX_VDISABLE) ||
+ (ch->ch_stopc == _POSIX_VDISABLE))
neo_set_no_output_flow_control(ch);
else
neo_set_ixon_flow_control(ch);
@@ -816,8 +844,12 @@ static void neo_param(struct tty_struct *tty)
if (ch->ch_digi.digi_flags & RTSPACE || ch->ch_c_cflag & CRTSCTS) {
neo_set_rts_flow_control(ch);
} else if (ch->ch_c_iflag & IXOFF) {
- /* If start/stop is set to disable, then we should disable flow control */
- if ((ch->ch_startc == _POSIX_VDISABLE) || (ch->ch_stopc == _POSIX_VDISABLE))
+ /*
+ * If start/stop is set to disable,
+ * then we should disable flow control
+ */
+ if ((ch->ch_startc == _POSIX_VDISABLE) ||
+ (ch->ch_stopc == _POSIX_VDISABLE))
neo_set_no_input_flow_control(ch);
else
neo_set_ixoff_flow_control(ch);
@@ -959,14 +991,18 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
/*
* If 0, no interrupts pending.
- * This can happen if the IRQ is shared among a couple Neo/Classic boards.
+ * This can happen if the IRQ is shared
+ * among a couple Neo/Classic boards.
*/
if (!uart_poll) {
spin_unlock_irqrestore(&brd->bd_intr_lock, flags);
return IRQ_NONE;
}
- /* At this point, we have at least SOMETHING to service, dig further... */
+ /*
+ * At this point, we have at least SOMETHING
+ * to service, dig further...
+ */
current_port = 0;
@@ -989,7 +1025,10 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
uart_poll &= ~(dgnc_offset_table[port]);
if (!type) {
- /* If no type, just ignore it, and move onto next port */
+ /*
+ * If no type, just ignore it,
+ * and move onto next port
+ */
continue;
}
@@ -1009,7 +1048,10 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
ch = brd->channels[port];
neo_copy_data_from_uart_to_queue(ch);
- /* Call our tty layer to enforce queue flow control if needed. */
+ /*
+ * Call our tty layer to
+ * enforce queue flow control if needed.
+ */
spin_lock_irqsave(&ch->ch_lock, flags2);
dgnc_check_queue_flow_control(ch);
spin_unlock_irqrestore(&ch->ch_lock, flags2);
@@ -1025,16 +1067,19 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
case UART_17158_TXRDY:
/*
- * TXRDY interrupt clears after reading ISR register for the UART channel.
+ * TXRDY interrupt clears after
+ * reading ISR register for the UART channel.
*/
/*
* Yes, this is odd...
* Why would I check EVERY possibility of type of
* interrupt, when we know its TXRDY???
- * Becuz for some reason, even tho we got triggered for TXRDY,
- * it seems to be occasionally wrong. Instead of TX, which
- * it should be, I was getting things like RXDY too. Weird.
+ * Because for some reason, even though
+ * we got triggered for TXRDY,
+ * it seems to be occasionally wrong.
+ * Instead of TX, which it should be,
+ * I was getting things like RXDY too. Weird.
*/
neo_parse_isr(brd, port);
continue;
@@ -1049,7 +1094,8 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
default:
/*
* The UART triggered us with a bogus interrupt type.
- * It appears the Exar chip, when REALLY bogged down, will throw
+ * It appears the Exar chip,
+ * when REALLY bogged down, will throw
* these once and awhile.
* Its harmless, just ignore it and move on.
*/
@@ -1200,7 +1246,8 @@ static void neo_copy_data_from_uart_to_queue(struct channel_t *ch)
linestatus = 0;
/* Copy data from uart to the queue */
- memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, n);
+ memcpy_fromio(ch->ch_rqueue + head,
+ &ch->ch_neo_uart->txrxburst, n);
/*
* Since RX_FIFO_DATA_ERROR was 0, we are guaranteed
@@ -1254,7 +1301,8 @@ static void neo_copy_data_from_uart_to_queue(struct channel_t *ch)
* we don't miss our TX FIFO emptys.
*/
if (linestatus & (UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR)) {
- linestatus &= ~(UART_LSR_THRE | UART_17158_TX_AND_FIFO_CLR);
+ linestatus &= ~(UART_LSR_THRE |
+ UART_17158_TX_AND_FIFO_CLR);
ch->ch_flags |= (CH_TX_FIFO_EMPTY | CH_TX_FIFO_LWM);
}
@@ -1270,7 +1318,8 @@ static void neo_copy_data_from_uart_to_queue(struct channel_t *ch)
}
/*
- * If our queue is full, we have no choice but to drop some data.
+ * If our queue is full,
+ * we have no choice but to drop some data.
* The assumption is that HWFLOW or SWFLOW should have stopped
* things way way before we got to this point.
*
@@ -1284,7 +1333,8 @@ static void neo_copy_data_from_uart_to_queue(struct channel_t *ch)
qleft++;
}
- memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, 1);
+ memcpy_fromio(ch->ch_rqueue + head,
+ &ch->ch_neo_uart->txrxburst, 1);
ch->ch_equeue[head] = (unsigned char) linestatus;
/* Ditch any remaining linestatus value. */
@@ -1339,7 +1389,8 @@ static int neo_drain(struct tty_struct *tty, uint seconds)
*
* NOTE: TODO: Do something with time passed in.
*/
- rc = wait_event_interruptible(un->un_flags_wait, ((un->un_flags & UN_EMPTY) == 0));
+ rc = wait_event_interruptible(un->un_flags_wait,
+ ((un->un_flags & UN_EMPTY) == 0));
/* If ret is non-zero, user ctrl-c'ed us */
return rc;
@@ -1359,12 +1410,16 @@ static void neo_flush_uart_write(struct channel_t *ch)
if (!ch || ch->magic != DGNC_CHANNEL_MAGIC)
return;
- writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
+ writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_XMIT),
+ &ch->ch_neo_uart->isr_fcr);
neo_pci_posting_flush(ch->ch_bd);
for (i = 0; i < 10; i++) {
- /* Check to see if the UART feels it completely flushed the FIFO. */
+ /*
+ * Check to see if the UART feels
+ * it completely flushed the FIFO.
+ */
tmp = readb(&ch->ch_neo_uart->isr_fcr);
if (tmp & 4)
udelay(10);
@@ -1389,12 +1444,16 @@ static void neo_flush_uart_read(struct channel_t *ch)
if (!ch || ch->magic != DGNC_CHANNEL_MAGIC)
return;
- writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR), &ch->ch_neo_uart->isr_fcr);
+ writeb((UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR),
+ &ch->ch_neo_uart->isr_fcr);
neo_pci_posting_flush(ch->ch_bd);
for (i = 0; i < 10; i++) {
- /* Check to see if the UART feels it completely flushed the FIFO. */
+ /*
+ * Check to see if the UART feels
+ * it completely flushed the FIFO.
+ */
tmp = readb(&ch->ch_neo_uart->isr_fcr);
if (tmp & 2)
udelay(10);
@@ -1440,8 +1499,10 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
ch->ch_cached_lsr &= ~(UART_LSR_THRE);
/*
- * If RTS Toggle mode is on, turn on RTS now if not already set,
- * and make sure we get an event when the data transfer has completed.
+ * If RTS Toggle mode is on,
+ * turn on RTS now if not already set,
+ * and make sure we get an event when
+ * the data transfer has completed.
*/
if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) {
if (!(ch->ch_mostat & UART_MCR_RTS)) {
@@ -1451,8 +1512,10 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
ch->ch_tun.un_flags |= (UN_EMPTY);
}
/*
- * If DTR Toggle mode is on, turn on DTR now if not already set,
- * and make sure we get an event when the data transfer has completed.
+ * If DTR Toggle mode is on,
+ * turn on DTR now if not already set,
+ * and make sure we get an event when
+ * the data transfer has completed.
*/
if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) {
if (!(ch->ch_mostat & UART_MCR_DTR)) {
@@ -1462,7 +1525,8 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
ch->ch_tun.un_flags |= (UN_EMPTY);
}
- writeb(ch->ch_wqueue[ch->ch_w_tail], &ch->ch_neo_uart->txrx);
+ writeb(ch->ch_wqueue[ch->ch_w_tail],
+ &ch->ch_neo_uart->txrx);
ch->ch_w_tail++;
ch->ch_w_tail &= WQUEUEMASK;
ch->ch_txcount++;
@@ -1508,7 +1572,8 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
/*
* If RTS Toggle mode is on, turn on RTS now if not already set,
- * and make sure we get an event when the data transfer has completed.
+ * and make sure we get an event when
+ * the data transfer has completed.
*/
if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) {
if (!(ch->ch_mostat & UART_MCR_RTS)) {
@@ -1520,7 +1585,8 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
/*
* If DTR Toggle mode is on, turn on DTR now if not already set,
- * and make sure we get an event when the data transfer has completed.
+ * and make sure we get an event when
+ * the data transfer has completed.
*/
if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) {
if (!(ch->ch_mostat & UART_MCR_DTR)) {
@@ -1530,7 +1596,8 @@ static void neo_copy_data_from_queue_to_uart(struct channel_t *ch)
ch->ch_tun.un_flags |= (UN_EMPTY);
}
- memcpy_toio(&ch->ch_neo_uart->txrxburst, ch->ch_wqueue + tail, s);
+ memcpy_toio(&ch->ch_neo_uart->txrxburst,
+ ch->ch_wqueue + tail, s);
/* Add and flip queue if needed */
tail = (tail + s) & WQUEUEMASK;
@@ -1584,7 +1651,7 @@ static void neo_parse_modem(struct channel_t *ch, unsigned char signals)
}
}
- /* Scrub off lower bits. They signify delta's, which I don't care about */
+ /* Scrub off lower bits. They signify delta's.*/
msignals &= 0xf0;
if (msignals & UART_MSR_DCD)
@@ -1671,7 +1738,8 @@ static void neo_uart_init(struct channel_t *ch)
/* Clear out UART and FIFO */
readb(&ch->ch_neo_uart->txrx);
- writeb((UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|UART_FCR_CLEAR_XMIT), &ch->ch_neo_uart->isr_fcr);
+ writeb((UART_FCR_ENABLE_FIFO|UART_FCR_CLEAR_RCVR|UART_FCR_CLEAR_XMIT),
+ &ch->ch_neo_uart->isr_fcr);
readb(&ch->ch_neo_uart->lsr);
readb(&ch->ch_neo_uart->msr);
@@ -1773,7 +1841,8 @@ static void neo_send_immediate_char(struct channel_t *ch, unsigned char c)
}
-static unsigned int neo_read_eeprom(unsigned char __iomem *base, unsigned int address)
+static unsigned int neo_read_eeprom(unsigned char __iomem *base,
+ unsigned int address)
{
unsigned int enable;
unsigned int bits;
@@ -1833,7 +1902,9 @@ static void neo_vpd(struct dgnc_board *brd)
}
if (((brd->vpd[0x08] != 0x82) /* long resource name tag */
- && (brd->vpd[0x10] != 0x82)) /* long resource name tag (PCI-66 files)*/
+ && (brd->vpd[0x10] != 0x82)) /* long resource
+ * name tag (PCI-66 files)
+ */
|| (brd->vpd[0x7F] != 0x78)) { /* small resource end tag */
memset(brd->vpd, '\0', NEO_VPD_IMAGESIZE);
--
1.9.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
