The bit defines in this header for the GPCT registers are not used. The ones in ni_tio_internal.h are used instead. Remove them from this header. Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx> Cc: Ian Abbott <abbotti@xxxxxxxxx> Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/staging/comedi/drivers/ni_stc.h | 68 --------------------------------- 1 file changed, 68 deletions(-) diff --git a/drivers/staging/comedi/drivers/ni_stc.h b/drivers/staging/comedi/drivers/ni_stc.h index da44951..45d8414 100644 --- a/drivers/staging/comedi/drivers/ni_stc.h +++ b/drivers/staging/comedi/drivers/ni_stc.h @@ -561,74 +561,6 @@ #define NISTC_AI_SI_SAVE_REG 64 #define NISTC_AI_SC_SAVE_REG 66 -/* command register */ -#define G_Disarm_Copy _bit15 /* strobe */ -#define G_Save_Trace_Copy _bit14 -#define G_Arm_Copy _bit13 /* strobe */ -#define G_Bank_Switch_Start _bit10 /* strobe */ -#define G_Little_Big_Endian _bit9 -#define G_Synchronized_Gate _bit8 -#define G_Write_Switch _bit7 -#define G_Up_Down(a) (((a)&0x03)<<5) -#define G_Disarm _bit4 /* strobe */ -#define G_Analog_Trigger_Reset _bit3 /* strobe */ -#define G_Save_Trace _bit1 -#define G_Arm _bit0 /* strobe */ - -/*channel agnostic names for the command register #defines */ -#define G_Bank_Switch_Enable _bit12 -#define G_Bank_Switch_Mode _bit11 -#define G_Load _bit2 /* strobe */ - -/* input select register */ -#define G_Gate_Select(a) (((a)&0x1f)<<7) -#define G_Source_Select(a) (((a)&0x1f)<<2) -#define G_Write_Acknowledges_Irq _bit1 -#define G_Read_Acknowledges_Irq _bit0 - -/* same input select register, but with channel agnostic names */ -#define G_Source_Polarity _bit15 -#define G_Output_Polarity _bit14 -#define G_OR_Gate _bit13 -#define G_Gate_Select_Load_Source _bit12 - -/* mode register */ -#define G_Loading_On_TC _bit12 -#define G_Output_Mode(a) (((a)&0x03)<<8) -#define G_Trigger_Mode_For_Edge_Gate(a) (((a)&0x03)<<3) -#define G_Gating_Mode(a) (((a)&0x03)<<0) - -/* same input mode register, but with channel agnostic names */ -#define G_Load_Source_Select _bit7 -#define G_Reload_Source_Switching _bit15 -#define G_Loading_On_Gate _bit14 -#define G_Gate_Polarity _bit13 - -#define G_Counting_Once(a) (((a)&0x03)<<10) -#define G_Stop_Mode(a) (((a)&0x03)<<5) -#define G_Gate_On_Both_Edges _bit2 - -/* G_Status_Register */ -#define G1_Gate_Error_St _bit15 -#define G0_Gate_Error_St _bit14 -#define G1_TC_Error_St _bit13 -#define G0_TC_Error_St _bit12 -#define G1_No_Load_Between_Gates_St _bit11 -#define G0_No_Load_Between_Gates_St _bit10 -#define G1_Armed_St _bit9 -#define G0_Armed_St _bit8 -#define G1_Stale_Data_St _bit7 -#define G0_Stale_Data_St _bit6 -#define G1_Next_Load_Source_St _bit5 -#define G0_Next_Load_Source_St _bit4 -#define G1_Counting_St _bit3 -#define G0_Counting_St _bit2 -#define G1_Save_St _bit1 -#define G0_Save_St _bit0 - -/* general purpose counter timer */ -#define G_Autoincrement(a) ((a)<<0) - /* Additional windowed registers unique to E series */ /* 16 bit registers shadowed from DAQ-STC */ -- 2.3.0 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
