From: Matteo Semenzato <mattew8898@xxxxxxxxx>
This patch fixes the following errors:
ERROR: space required after that ','
ERROR: trailing whitespace
ERROR: code indent should use tabs where possible
V2: The patch should apply now
Signed-off-by: Matteo Semenzato <mattew8898@xxxxxxxxx>
---
drivers/staging/fbtft/fb_st7735r.c | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)
diff --git a/drivers/staging/fbtft/fb_st7735r.c b/drivers/staging/fbtft/fb_st7735r.c
index b63aa38..4974086 100644
--- a/drivers/staging/fbtft/fb_st7735r.c
+++ b/drivers/staging/fbtft/fb_st7735r.c
@@ -26,25 +26,25 @@
#define DRVNAME "fb_st7735r"
#define DEFAULT_GAMMA "0F 1A 0F 18 2F 28 20 22 1F 1B 23 37 00 07 02 10\n" \
- "0F 1B 0F 17 33 2C 29 2E 30 30 39 3F 00 07 03 10"
+ "0F 1B 0F 17 33 2C 29 2E 30 30 39 3F 00 07 03 10"
static int default_init_sequence[] = {
/* SWRESET - Software reset */
- -1, 0x01,
+ -1, 0x01,
-2, 150, /* delay */
/* SLPOUT - Sleep out & booster on */
- -1, 0x11,
+ -1, 0x11,
-2, 500, /* delay */
/* FRMCTR1 - frame rate control: normal mode
frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D) */
- -1, 0xB1, 0x01, 0x2C, 0x2D,
+ -1, 0xB1, 0x01, 0x2C, 0x2D,
/* FRMCTR2 - frame rate control: idle mode
frame rate = fosc / (1 x 2 + 40) * (LINE + 2C + 2D) */
- -1, 0xB2, 0x01, 0x2C, 0x2D,
+ -1, 0xB2, 0x01, 0x2C, 0x2D,
/* FRMCTR3 - frame rate control - partial mode
dot inversion mode, line inversion mode */
@@ -68,7 +68,7 @@ static int default_init_sequence[] = {
/* PWCTR4 - Power Control
BCLK/2, Opamp current small & Medium low */
- -1, 0xC3,0x8A,0x2A,
+ -1, 0xC3, 0x8A, 0x2A,
/* PWCTR5 - Power Control */
-1, 0xC4, 0x8A, 0xEE,
@@ -91,7 +91,7 @@ static int default_init_sequence[] = {
-2, 10, /* delay */
/* end marker */
- -3
+ -3
};
static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
@@ -119,9 +119,9 @@ static int set_var(struct fbtft_par *par)
/* MADCTL - Memory data access control
RGB/BGR:
1. Mode selection pin SRGB
- RGB H/W pin for color filter setting: 0=RGB, 1=BGR
+ RGB H/W pin for color filter setting: 0=RGB, 1=BGR
2. MADCTL RGB bit
- RGB-BGR ORDER color filter panel: 0=RGB, 1=BGR */
+ RGB-BGR ORDER color filter panel: 0=RGB, 1=BGR */
switch (par->info->var.rotate) {
case 0:
write_reg(par, 0x36, MX | MY | (par->bgr << 3));
@@ -148,21 +148,21 @@ static int set_var(struct fbtft_par *par)
#define CURVE(num, idx) curves[num*par->gamma.num_values + idx]
static int set_gamma(struct fbtft_par *par, unsigned long *curves)
{
- int i,j;
+ int i, j;
fbtft_par_dbg(DEBUG_INIT_DISPLAY, par, "%s()\n", __func__);
/* apply mask */
for (i = 0; i < par->gamma.num_curves; i++)
for (j = 0; j < par->gamma.num_values; j++)
- CURVE(i,j) &= 0b111111;
+ CURVE(i, j) &= 0b111111;
for (i = 0; i < par->gamma.num_curves; i++)
write_reg(par, 0xE0 + i,
CURVE(i, 0), CURVE(i, 1), CURVE(i, 2), CURVE(i, 3),
CURVE(i, 4), CURVE(i, 5), CURVE(i, 6), CURVE(i, 7),
CURVE(i, 8), CURVE(i, 9), CURVE(i, 10), CURVE(i, 11),
- CURVE(i, 12), CURVE(i, 13), CURVE(i, 14), CURVE(i,15));
+ CURVE(i, 12), CURVE(i, 13), CURVE(i, 14), CURVE(i, 15));
return 0;
}
--
2.3.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
