From: Micky Ching <micky_ching@xxxxxxxxxxxxxx> It is more readable to place register address and values define togather. The values define add two leading space indicate belong to the register address defined above. Signed-off-by: Micky Ching <micky_ching@xxxxxxxxxxxxxx> Acked-by: Lee Jones <lee.jones@xxxxxxxxxx> --- include/linux/mfd/rtsx_pci.h | 836 +++++++++++++++++++------------------------ 1 file changed, 369 insertions(+), 467 deletions(-) diff --git a/include/linux/mfd/rtsx_pci.h b/include/linux/mfd/rtsx_pci.h index a9c2a14..e81f2bb 100644 --- a/include/linux/mfd/rtsx_pci.h +++ b/include/linux/mfd/rtsx_pci.h @@ -28,74 +28,72 @@ #define MAX_RW_REG_CNT 1024 -/* PCI Operation Register Address */ #define RTSX_HCBAR 0x00 #define RTSX_HCBCTLR 0x04 +#define STOP_CMD (0x01 << 28) +#define READ_REG_CMD 0 +#define WRITE_REG_CMD 1 +#define CHECK_REG_CMD 2 + #define RTSX_HDBAR 0x08 +#define SG_INT 0x04 +#define SG_END 0x02 +#define SG_VALID 0x01 +#define SG_NO_OP 0x00 +#define SG_TRANS_DATA (0x02 << 4) +#define SG_LINK_DESC (0x03 << 4) #define RTSX_HDBCTLR 0x0C +#define SDMA_MODE 0x00 +#define ADMA_MODE (0x02 << 26) +#define STOP_DMA (0x01 << 28) +#define TRIG_DMA (0x01 << 31) + #define RTSX_HAIMR 0x10 -#define RTSX_BIPR 0x14 -#define RTSX_BIER 0x18 +#define HAIMR_TRANS_START (0x01 << 31) +#define HAIMR_READ 0x00 +#define HAIMR_WRITE (0x01 << 30) +#define HAIMR_READ_START (HAIMR_TRANS_START | HAIMR_READ) +#define HAIMR_WRITE_START (HAIMR_TRANS_START | HAIMR_WRITE) +#define HAIMR_TRANS_END (HAIMR_TRANS_START) -/* Host command buffer control register */ -#define STOP_CMD (0x01 << 28) - -/* Host data buffer control register */ -#define SDMA_MODE 0x00 -#define ADMA_MODE (0x02 << 26) -#define STOP_DMA (0x01 << 28) -#define TRIG_DMA (0x01 << 31) - -/* Host access internal memory register */ -#define HAIMR_TRANS_START (0x01 << 31) -#define HAIMR_READ 0x00 -#define HAIMR_WRITE (0x01 << 30) -#define HAIMR_READ_START (HAIMR_TRANS_START | HAIMR_READ) -#define HAIMR_WRITE_START (HAIMR_TRANS_START | HAIMR_WRITE) -#define HAIMR_TRANS_END (HAIMR_TRANS_START) - -/* Bus interrupt pending register */ -#define CMD_DONE_INT (1 << 31) -#define DATA_DONE_INT (1 << 30) -#define TRANS_OK_INT (1 << 29) -#define TRANS_FAIL_INT (1 << 28) -#define XD_INT (1 << 27) -#define MS_INT (1 << 26) -#define SD_INT (1 << 25) -#define GPIO0_INT (1 << 24) -#define OC_INT (1 << 23) -#define SD_WRITE_PROTECT (1 << 19) -#define XD_EXIST (1 << 18) -#define MS_EXIST (1 << 17) -#define SD_EXIST (1 << 16) -#define DELINK_INT GPIO0_INT -#define MS_OC_INT (1 << 23) -#define SD_OC_INT (1 << 22) +#define RTSX_BIPR 0x14 +#define CMD_DONE_INT (1 << 31) +#define DATA_DONE_INT (1 << 30) +#define TRANS_OK_INT (1 << 29) +#define TRANS_FAIL_INT (1 << 28) +#define XD_INT (1 << 27) +#define MS_INT (1 << 26) +#define SD_INT (1 << 25) +#define GPIO0_INT (1 << 24) +#define OC_INT (1 << 23) +#define SD_WRITE_PROTECT (1 << 19) +#define XD_EXIST (1 << 18) +#define MS_EXIST (1 << 17) +#define SD_EXIST (1 << 16) +#define DELINK_INT GPIO0_INT +#define MS_OC_INT (1 << 23) +#define SD_OC_INT (1 << 22) #define CARD_INT (XD_INT | MS_INT | SD_INT) #define NEED_COMPLETE_INT (DATA_DONE_INT | TRANS_OK_INT | TRANS_FAIL_INT) #define RTSX_INT (CMD_DONE_INT | NEED_COMPLETE_INT | \ CARD_INT | GPIO0_INT | OC_INT) - #define CARD_EXIST (XD_EXIST | MS_EXIST | SD_EXIST) -/* Bus interrupt enable register */ -#define CMD_DONE_INT_EN (1 << 31) -#define DATA_DONE_INT_EN (1 << 30) -#define TRANS_OK_INT_EN (1 << 29) -#define TRANS_FAIL_INT_EN (1 << 28) -#define XD_INT_EN (1 << 27) -#define MS_INT_EN (1 << 26) -#define SD_INT_EN (1 << 25) -#define GPIO0_INT_EN (1 << 24) -#define OC_INT_EN (1 << 23) -#define DELINK_INT_EN GPIO0_INT_EN -#define MS_OC_INT_EN (1 << 23) -#define SD_OC_INT_EN (1 << 22) - -#define READ_REG_CMD 0 -#define WRITE_REG_CMD 1 -#define CHECK_REG_CMD 2 +#define RTSX_BIER 0x18 +#define CMD_DONE_INT_EN (1 << 31) +#define DATA_DONE_INT_EN (1 << 30) +#define TRANS_OK_INT_EN (1 << 29) +#define TRANS_FAIL_INT_EN (1 << 28) +#define XD_INT_EN (1 << 27) +#define MS_INT_EN (1 << 26) +#define SD_INT_EN (1 << 25) +#define GPIO0_INT_EN (1 << 24) +#define OC_INT_EN (1 << 23) +#define DELINK_INT_EN GPIO0_INT_EN +#define MS_OC_INT_EN (1 << 23) +#define SD_OC_INT_EN (1 << 22) + /* * macros for easy use @@ -125,423 +123,68 @@ #define rtsx_pci_write_config_dword(pcr, where, val) \ pci_write_config_dword((pcr)->pci, where, val) -#define STATE_TRANS_NONE 0 -#define STATE_TRANS_CMD 1 -#define STATE_TRANS_BUF 2 -#define STATE_TRANS_SG 3 - -#define TRANS_NOT_READY 0 -#define TRANS_RESULT_OK 1 -#define TRANS_RESULT_FAIL 2 -#define TRANS_NO_DEVICE 3 - -#define RTSX_RESV_BUF_LEN 4096 -#define HOST_CMDS_BUF_LEN 1024 -#define HOST_SG_TBL_BUF_LEN (RTSX_RESV_BUF_LEN - HOST_CMDS_BUF_LEN) -#define HOST_SG_TBL_ITEMS (HOST_SG_TBL_BUF_LEN / 8) -#define MAX_SG_ITEM_LEN 0x80000 - -#define HOST_TO_DEVICE 0 -#define DEVICE_TO_HOST 1 - -#define RTSX_PHASE_MAX 32 -#define RX_TUNING_CNT 3 - -/* SG descriptor */ -#define SG_INT 0x04 -#define SG_END 0x02 -#define SG_VALID 0x01 - -#define SG_NO_OP 0x00 -#define SG_TRANS_DATA (0x02 << 4) -#define SG_LINK_DESC (0x03 << 4) - -/* Output voltage */ -#define OUTPUT_3V3 0 -#define OUTPUT_1V8 1 - -/* Card Clock Enable Register */ -#define SD_CLK_EN 0x04 -#define MS_CLK_EN 0x08 - -/* Card Select Register */ -#define SD_MOD_SEL 2 -#define MS_MOD_SEL 3 - -/* Card Output Enable Register */ -#define SD_OUTPUT_EN 0x04 -#define MS_OUTPUT_EN 0x08 - -/* CARD_SHARE_MODE */ -#define CARD_SHARE_MASK 0x0F -#define CARD_SHARE_MULTI_LUN 0x00 -#define CARD_SHARE_NORMAL 0x00 -#define CARD_SHARE_48_SD 0x04 -#define CARD_SHARE_48_MS 0x08 -/* CARD_SHARE_MODE for barossa */ -#define CARD_SHARE_BAROSSA_SD 0x01 -#define CARD_SHARE_BAROSSA_MS 0x02 - -/* CARD_DRIVE_SEL */ -#define MS_DRIVE_8mA (0x01 << 6) -#define MMC_DRIVE_8mA (0x01 << 4) -#define XD_DRIVE_8mA (0x01 << 2) -#define GPIO_DRIVE_8mA 0x01 -#define RTS5209_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\ - XD_DRIVE_8mA | GPIO_DRIVE_8mA) -#define RTL8411_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\ - XD_DRIVE_8mA) -#define RTSX_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | GPIO_DRIVE_8mA) +#define STATE_TRANS_NONE 0 +#define STATE_TRANS_CMD 1 +#define STATE_TRANS_BUF 2 +#define STATE_TRANS_SG 3 -/* SD30_DRIVE_SEL */ -#define DRIVER_TYPE_A 0x05 -#define DRIVER_TYPE_B 0x03 -#define DRIVER_TYPE_C 0x02 -#define DRIVER_TYPE_D 0x01 -#define CFG_DRIVER_TYPE_A 0x02 -#define CFG_DRIVER_TYPE_B 0x03 -#define CFG_DRIVER_TYPE_C 0x01 -#define CFG_DRIVER_TYPE_D 0x00 - -/* FPDCTL */ -#define SSC_POWER_DOWN 0x01 -#define SD_OC_POWER_DOWN 0x02 -#define ALL_POWER_DOWN 0x07 -#define OC_POWER_DOWN 0x06 - -/* CLK_CTL */ -#define CHANGE_CLK 0x01 - -/* LDO_CTL */ -#define BPP_ASIC_1V7 0x00 -#define BPP_ASIC_1V8 0x01 -#define BPP_ASIC_1V9 0x02 -#define BPP_ASIC_2V0 0x03 -#define BPP_ASIC_2V7 0x04 -#define BPP_ASIC_2V8 0x05 -#define BPP_ASIC_3V2 0x06 -#define BPP_ASIC_3V3 0x07 -#define BPP_REG_TUNED18 0x07 -#define BPP_TUNED18_SHIFT_8402 5 -#define BPP_TUNED18_SHIFT_8411 4 -#define BPP_PAD_MASK 0x04 -#define BPP_PAD_3V3 0x04 -#define BPP_PAD_1V8 0x00 -#define BPP_LDO_POWB 0x03 -#define BPP_LDO_ON 0x00 -#define BPP_LDO_SUSPEND 0x02 -#define BPP_LDO_OFF 0x03 - -/* CD_PAD_CTL */ -#define CD_DISABLE_MASK 0x07 -#define MS_CD_DISABLE 0x04 -#define SD_CD_DISABLE 0x02 -#define XD_CD_DISABLE 0x01 -#define CD_DISABLE 0x07 -#define CD_ENABLE 0x00 -#define MS_CD_EN_ONLY 0x03 -#define SD_CD_EN_ONLY 0x05 -#define XD_CD_EN_ONLY 0x06 -#define FORCE_CD_LOW_MASK 0x38 -#define FORCE_CD_XD_LOW 0x08 -#define FORCE_CD_SD_LOW 0x10 -#define FORCE_CD_MS_LOW 0x20 -#define CD_AUTO_DISABLE 0x40 - -/* SD_STAT1 */ -#define SD_CRC7_ERR 0x80 -#define SD_CRC16_ERR 0x40 -#define SD_CRC_WRITE_ERR 0x20 -#define SD_CRC_WRITE_ERR_MASK 0x1C -#define GET_CRC_TIME_OUT 0x02 -#define SD_TUNING_COMPARE_ERR 0x01 - -/* SD_STAT2 */ -#define SD_RSP_80CLK_TIMEOUT 0x01 - -/* SD_BUS_STAT */ -#define SD_CLK_TOGGLE_EN 0x80 -#define SD_CLK_FORCE_STOP 0x40 -#define SD_DAT3_STATUS 0x10 -#define SD_DAT2_STATUS 0x08 -#define SD_DAT1_STATUS 0x04 -#define SD_DAT0_STATUS 0x02 -#define SD_CMD_STATUS 0x01 - -/* SD_PAD_CTL */ -#define SD_IO_USING_1V8 0x80 -#define SD_IO_USING_3V3 0x7F -#define TYPE_A_DRIVING 0x00 -#define TYPE_B_DRIVING 0x01 -#define TYPE_C_DRIVING 0x02 -#define TYPE_D_DRIVING 0x03 - -/* SD_SAMPLE_POINT_CTL */ -#define DDR_FIX_RX_DAT 0x00 -#define DDR_VAR_RX_DAT 0x80 -#define DDR_FIX_RX_DAT_EDGE 0x00 -#define DDR_FIX_RX_DAT_14_DELAY 0x40 -#define DDR_FIX_RX_CMD 0x00 -#define DDR_VAR_RX_CMD 0x20 -#define DDR_FIX_RX_CMD_POS_EDGE 0x00 -#define DDR_FIX_RX_CMD_14_DELAY 0x10 -#define SD20_RX_POS_EDGE 0x00 -#define SD20_RX_14_DELAY 0x08 -#define SD20_RX_SEL_MASK 0x08 +#define TRANS_NOT_READY 0 +#define TRANS_RESULT_OK 1 +#define TRANS_RESULT_FAIL 2 +#define TRANS_NO_DEVICE 3 -/* SD_PUSH_POINT_CTL */ -#define DDR_FIX_TX_CMD_DAT 0x00 -#define DDR_VAR_TX_CMD_DAT 0x80 -#define DDR_FIX_TX_DAT_14_TSU 0x00 -#define DDR_FIX_TX_DAT_12_TSU 0x40 -#define DDR_FIX_TX_CMD_NEG_EDGE 0x00 -#define DDR_FIX_TX_CMD_14_AHEAD 0x20 -#define SD20_TX_NEG_EDGE 0x00 -#define SD20_TX_14_AHEAD 0x10 -#define SD20_TX_SEL_MASK 0x10 -#define DDR_VAR_SDCLK_POL_SWAP 0x01 - -/* SD_TRANSFER */ -#define SD_TRANSFER_START 0x80 -#define SD_TRANSFER_END 0x40 -#define SD_STAT_IDLE 0x20 -#define SD_TRANSFER_ERR 0x10 -/* SD Transfer Mode definition */ -#define SD_TM_NORMAL_WRITE 0x00 -#define SD_TM_AUTO_WRITE_3 0x01 -#define SD_TM_AUTO_WRITE_4 0x02 -#define SD_TM_AUTO_READ_3 0x05 -#define SD_TM_AUTO_READ_4 0x06 -#define SD_TM_CMD_RSP 0x08 -#define SD_TM_AUTO_WRITE_1 0x09 -#define SD_TM_AUTO_WRITE_2 0x0A -#define SD_TM_NORMAL_READ 0x0C -#define SD_TM_AUTO_READ_1 0x0D -#define SD_TM_AUTO_READ_2 0x0E -#define SD_TM_AUTO_TUNING 0x0F - -/* SD_VPTX_CTL / SD_VPRX_CTL */ -#define PHASE_CHANGE 0x80 -#define PHASE_NOT_RESET 0x40 - -/* SD_DCMPS_TX_CTL / SD_DCMPS_RX_CTL */ -#define DCMPS_CHANGE 0x80 -#define DCMPS_CHANGE_DONE 0x40 -#define DCMPS_ERROR 0x20 -#define DCMPS_CURRENT_PHASE 0x1F - -/* SD Configure 1 Register */ -#define SD_CLK_DIVIDE_0 0x00 -#define SD_CLK_DIVIDE_256 0xC0 -#define SD_CLK_DIVIDE_128 0x80 -#define SD_BUS_WIDTH_1BIT 0x00 -#define SD_BUS_WIDTH_4BIT 0x01 -#define SD_BUS_WIDTH_8BIT 0x02 -#define SD_ASYNC_FIFO_NOT_RST 0x10 -#define SD_20_MODE 0x00 -#define SD_DDR_MODE 0x04 -#define SD_30_MODE 0x08 - -#define SD_CLK_DIVIDE_MASK 0xC0 - -/* SD_CMD_STATE */ -#define SD_CMD_IDLE 0x80 - -/* SD_DATA_STATE */ -#define SD_DATA_IDLE 0x80 - -/* DCM_DRP_CTL */ -#define DCM_RESET 0x08 -#define DCM_LOCKED 0x04 -#define DCM_208M 0x00 -#define DCM_TX 0x01 -#define DCM_RX 0x02 - -/* DCM_DRP_TRIG */ -#define DRP_START 0x80 -#define DRP_DONE 0x40 - -/* DCM_DRP_CFG */ -#define DRP_WRITE 0x80 -#define DRP_READ 0x00 -#define DCM_WRITE_ADDRESS_50 0x50 -#define DCM_WRITE_ADDRESS_51 0x51 -#define DCM_READ_ADDRESS_00 0x00 -#define DCM_READ_ADDRESS_51 0x51 - -/* IRQSTAT0 */ -#define DMA_DONE_INT 0x80 -#define SUSPEND_INT 0x40 -#define LINK_RDY_INT 0x20 -#define LINK_DOWN_INT 0x10 - -/* DMACTL */ -#define DMA_RST 0x80 -#define DMA_BUSY 0x04 -#define DMA_DIR_TO_CARD 0x00 -#define DMA_DIR_FROM_CARD 0x02 -#define DMA_EN 0x01 -#define DMA_128 (0 << 4) -#define DMA_256 (1 << 4) -#define DMA_512 (2 << 4) -#define DMA_1024 (3 << 4) -#define DMA_PACK_SIZE_MASK 0x30 - -/* SSC_CTL1 */ -#define SSC_RSTB 0x80 -#define SSC_8X_EN 0x40 -#define SSC_FIX_FRAC 0x20 -#define SSC_SEL_1M 0x00 -#define SSC_SEL_2M 0x08 -#define SSC_SEL_4M 0x10 -#define SSC_SEL_8M 0x18 - -/* SSC_CTL2 */ -#define SSC_DEPTH_MASK 0x07 -#define SSC_DEPTH_DISALBE 0x00 -#define SSC_DEPTH_4M 0x01 -#define SSC_DEPTH_2M 0x02 -#define SSC_DEPTH_1M 0x03 -#define SSC_DEPTH_500K 0x04 -#define SSC_DEPTH_250K 0x05 - -/* System Clock Control Register */ -#define CLK_LOW_FREQ 0x01 - -/* System Clock Divider Register */ -#define CLK_DIV_1 0x01 -#define CLK_DIV_2 0x02 -#define CLK_DIV_4 0x03 -#define CLK_DIV_8 0x04 - -/* MS_CFG */ -#define SAMPLE_TIME_RISING 0x00 -#define SAMPLE_TIME_FALLING 0x80 -#define PUSH_TIME_DEFAULT 0x00 -#define PUSH_TIME_ODD 0x40 -#define NO_EXTEND_TOGGLE 0x00 -#define EXTEND_TOGGLE_CHK 0x20 -#define MS_BUS_WIDTH_1 0x00 -#define MS_BUS_WIDTH_4 0x10 -#define MS_BUS_WIDTH_8 0x18 -#define MS_2K_SECTOR_MODE 0x04 -#define MS_512_SECTOR_MODE 0x00 -#define MS_TOGGLE_TIMEOUT_EN 0x00 -#define MS_TOGGLE_TIMEOUT_DISEN 0x01 -#define MS_NO_CHECK_INT 0x02 +#define RTSX_RESV_BUF_LEN 4096 +#define HOST_CMDS_BUF_LEN 1024 +#define HOST_SG_TBL_BUF_LEN (RTSX_RESV_BUF_LEN - HOST_CMDS_BUF_LEN) +#define HOST_SG_TBL_ITEMS (HOST_SG_TBL_BUF_LEN / 8) +#define MAX_SG_ITEM_LEN 0x80000 +#define HOST_TO_DEVICE 0 +#define DEVICE_TO_HOST 1 + +#define OUTPUT_3V3 0 +#define OUTPUT_1V8 1 -/* MS_TRANS_CFG */ -#define WAIT_INT 0x80 -#define NO_WAIT_INT 0x00 -#define NO_AUTO_READ_INT_REG 0x00 -#define AUTO_READ_INT_REG 0x40 -#define MS_CRC16_ERR 0x20 -#define MS_RDY_TIMEOUT 0x10 -#define MS_INT_CMDNK 0x08 -#define MS_INT_BREQ 0x04 -#define MS_INT_ERR 0x02 -#define MS_INT_CED 0x01 - -/* MS_TRANSFER */ -#define MS_TRANSFER_START 0x80 -#define MS_TRANSFER_END 0x40 -#define MS_TRANSFER_ERR 0x20 -#define MS_BS_STATE 0x10 -#define MS_TM_READ_BYTES 0x00 -#define MS_TM_NORMAL_READ 0x01 -#define MS_TM_WRITE_BYTES 0x04 -#define MS_TM_NORMAL_WRITE 0x05 -#define MS_TM_AUTO_READ 0x08 -#define MS_TM_AUTO_WRITE 0x0C - -/* SD Configure 2 Register */ -#define SD_CALCULATE_CRC7 0x00 -#define SD_NO_CALCULATE_CRC7 0x80 -#define SD_CHECK_CRC16 0x00 -#define SD_NO_CHECK_CRC16 0x40 -#define SD_NO_CHECK_WAIT_CRC_TO 0x20 -#define SD_WAIT_BUSY_END 0x08 -#define SD_NO_WAIT_BUSY_END 0x00 -#define SD_CHECK_CRC7 0x00 -#define SD_NO_CHECK_CRC7 0x04 -#define SD_RSP_LEN_0 0x00 -#define SD_RSP_LEN_6 0x01 -#define SD_RSP_LEN_17 0x02 -/* SD/MMC Response Type Definition */ -#define SD_RSP_TYPE_R0 0x04 -#define SD_RSP_TYPE_R1 0x01 -#define SD_RSP_TYPE_R1b 0x09 -#define SD_RSP_TYPE_R2 0x02 -#define SD_RSP_TYPE_R3 0x05 -#define SD_RSP_TYPE_R4 0x05 -#define SD_RSP_TYPE_R5 0x01 -#define SD_RSP_TYPE_R6 0x01 -#define SD_RSP_TYPE_R7 0x01 - -/* SD_CONFIGURE3 */ -#define SD_RSP_80CLK_TIMEOUT_EN 0x01 - -/* Card Transfer Reset Register */ -#define SPI_STOP 0x01 -#define XD_STOP 0x02 -#define SD_STOP 0x04 -#define MS_STOP 0x08 -#define SPI_CLR_ERR 0x10 -#define XD_CLR_ERR 0x20 -#define SD_CLR_ERR 0x40 -#define MS_CLR_ERR 0x80 - -/* Card Data Source Register */ -#define PINGPONG_BUFFER 0x01 -#define RING_BUFFER 0x00 - -/* Card Power Control Register */ -#define PMOS_STRG_MASK 0x10 -#define PMOS_STRG_800mA 0x10 -#define PMOS_STRG_400mA 0x00 -#define SD_POWER_OFF 0x03 -#define SD_PARTIAL_POWER_ON 0x01 -#define SD_POWER_ON 0x00 -#define SD_POWER_MASK 0x03 -#define MS_POWER_OFF 0x0C -#define MS_PARTIAL_POWER_ON 0x04 -#define MS_POWER_ON 0x00 -#define MS_POWER_MASK 0x0C -#define BPP_POWER_OFF 0x0F -#define BPP_POWER_5_PERCENT_ON 0x0E -#define BPP_POWER_10_PERCENT_ON 0x0C -#define BPP_POWER_15_PERCENT_ON 0x08 -#define BPP_POWER_ON 0x00 -#define BPP_POWER_MASK 0x0F -#define SD_VCC_PARTIAL_POWER_ON 0x02 -#define SD_VCC_POWER_ON 0x00 - -/* PWR_GATE_CTRL */ -#define PWR_GATE_EN 0x01 -#define LDO3318_PWR_MASK 0x06 -#define LDO_ON 0x00 -#define LDO_SUSPEND 0x04 -#define LDO_OFF 0x06 - -/* CARD_CLK_SOURCE */ -#define CRC_FIX_CLK (0x00 << 0) -#define CRC_VAR_CLK0 (0x01 << 0) -#define CRC_VAR_CLK1 (0x02 << 0) -#define SD30_FIX_CLK (0x00 << 2) -#define SD30_VAR_CLK0 (0x01 << 2) -#define SD30_VAR_CLK1 (0x02 << 2) -#define SAMPLE_FIX_CLK (0x00 << 4) -#define SAMPLE_VAR_CLK0 (0x01 << 4) -#define SAMPLE_VAR_CLK1 (0x02 << 4) - -/* HOST_SLEEP_STATE */ -#define HOST_ENTER_S1 1 -#define HOST_ENTER_S3 2 +#define RTSX_PHASE_MAX 32 +#define RX_TUNING_CNT 3 #define MS_CFG 0xFD40 +#define SAMPLE_TIME_RISING 0x00 +#define SAMPLE_TIME_FALLING 0x80 +#define PUSH_TIME_DEFAULT 0x00 +#define PUSH_TIME_ODD 0x40 +#define NO_EXTEND_TOGGLE 0x00 +#define EXTEND_TOGGLE_CHK 0x20 +#define MS_BUS_WIDTH_1 0x00 +#define MS_BUS_WIDTH_4 0x10 +#define MS_BUS_WIDTH_8 0x18 +#define MS_2K_SECTOR_MODE 0x04 +#define MS_512_SECTOR_MODE 0x00 +#define MS_TOGGLE_TIMEOUT_EN 0x00 +#define MS_TOGGLE_TIMEOUT_DISEN 0x01 +#define MS_NO_CHECK_INT 0x02 #define MS_TPC 0xFD41 #define MS_TRANS_CFG 0xFD42 +#define WAIT_INT 0x80 +#define NO_WAIT_INT 0x00 +#define NO_AUTO_READ_INT_REG 0x00 +#define AUTO_READ_INT_REG 0x40 +#define MS_CRC16_ERR 0x20 +#define MS_RDY_TIMEOUT 0x10 +#define MS_INT_CMDNK 0x08 +#define MS_INT_BREQ 0x04 +#define MS_INT_ERR 0x02 +#define MS_INT_CED 0x01 #define MS_TRANSFER 0xFD43 +#define MS_TRANSFER_START 0x80 +#define MS_TRANSFER_END 0x40 +#define MS_TRANSFER_ERR 0x20 +#define MS_BS_STATE 0x10 +#define MS_TM_READ_BYTES 0x00 +#define MS_TM_NORMAL_READ 0x01 +#define MS_TM_WRITE_BYTES 0x04 +#define MS_TM_NORMAL_WRITE 0x05 +#define MS_TM_AUTO_READ 0x08 +#define MS_TM_AUTO_WRITE 0x0C #define MS_INT_REG 0xFD44 #define MS_BYTE_CNT 0xFD45 #define MS_SECTOR_CNT_L 0xFD46 @@ -549,14 +192,90 @@ #define MS_DBUS_H 0xFD48 #define SD_CFG1 0xFDA0 +#define SD_CLK_DIVIDE_0 0x00 +#define SD_CLK_DIVIDE_256 0xC0 +#define SD_CLK_DIVIDE_128 0x80 +#define SD_BUS_WIDTH_1BIT 0x00 +#define SD_BUS_WIDTH_4BIT 0x01 +#define SD_BUS_WIDTH_8BIT 0x02 +#define SD_ASYNC_FIFO_NOT_RST 0x10 +#define SD_20_MODE 0x00 +#define SD_DDR_MODE 0x04 +#define SD_30_MODE 0x08 +#define SD_CLK_DIVIDE_MASK 0xC0 #define SD_CFG2 0xFDA1 +#define SD_CALCULATE_CRC7 0x00 +#define SD_NO_CALCULATE_CRC7 0x80 +#define SD_CHECK_CRC16 0x00 +#define SD_NO_CHECK_CRC16 0x40 +#define SD_NO_CHECK_WAIT_CRC_TO 0x20 +#define SD_WAIT_BUSY_END 0x08 +#define SD_NO_WAIT_BUSY_END 0x00 +#define SD_CHECK_CRC7 0x00 +#define SD_NO_CHECK_CRC7 0x04 +#define SD_RSP_LEN_0 0x00 +#define SD_RSP_LEN_6 0x01 +#define SD_RSP_LEN_17 0x02 +#define SD_RSP_TYPE_R0 0x04 +#define SD_RSP_TYPE_R1 0x01 +#define SD_RSP_TYPE_R1b 0x09 +#define SD_RSP_TYPE_R2 0x02 +#define SD_RSP_TYPE_R3 0x05 +#define SD_RSP_TYPE_R4 0x05 +#define SD_RSP_TYPE_R5 0x01 +#define SD_RSP_TYPE_R6 0x01 +#define SD_RSP_TYPE_R7 0x01 #define SD_CFG3 0xFDA2 +#define SD_RSP_80CLK_TIMEOUT_EN 0x01 + #define SD_STAT1 0xFDA3 +#define SD_CRC7_ERR 0x80 +#define SD_CRC16_ERR 0x40 +#define SD_CRC_WRITE_ERR 0x20 +#define SD_CRC_WRITE_ERR_MASK 0x1C +#define GET_CRC_TIME_OUT 0x02 +#define SD_TUNING_COMPARE_ERR 0x01 #define SD_STAT2 0xFDA4 +#define SD_RSP_80CLK_TIMEOUT 0x01 + #define SD_BUS_STAT 0xFDA5 +#define SD_CLK_TOGGLE_EN 0x80 +#define SD_CLK_FORCE_STOP 0x40 +#define SD_DAT3_STATUS 0x10 +#define SD_DAT2_STATUS 0x08 +#define SD_DAT1_STATUS 0x04 +#define SD_DAT0_STATUS 0x02 +#define SD_CMD_STATUS 0x01 #define SD_PAD_CTL 0xFDA6 +#define SD_IO_USING_1V8 0x80 +#define SD_IO_USING_3V3 0x7F +#define TYPE_A_DRIVING 0x00 +#define TYPE_B_DRIVING 0x01 +#define TYPE_C_DRIVING 0x02 +#define TYPE_D_DRIVING 0x03 #define SD_SAMPLE_POINT_CTL 0xFDA7 +#define DDR_FIX_RX_DAT 0x00 +#define DDR_VAR_RX_DAT 0x80 +#define DDR_FIX_RX_DAT_EDGE 0x00 +#define DDR_FIX_RX_DAT_14_DELAY 0x40 +#define DDR_FIX_RX_CMD 0x00 +#define DDR_VAR_RX_CMD 0x20 +#define DDR_FIX_RX_CMD_POS_EDGE 0x00 +#define DDR_FIX_RX_CMD_14_DELAY 0x10 +#define SD20_RX_POS_EDGE 0x00 +#define SD20_RX_14_DELAY 0x08 +#define SD20_RX_SEL_MASK 0x08 #define SD_PUSH_POINT_CTL 0xFDA8 +#define DDR_FIX_TX_CMD_DAT 0x00 +#define DDR_VAR_TX_CMD_DAT 0x80 +#define DDR_FIX_TX_DAT_14_TSU 0x00 +#define DDR_FIX_TX_DAT_12_TSU 0x40 +#define DDR_FIX_TX_CMD_NEG_EDGE 0x00 +#define DDR_FIX_TX_CMD_14_AHEAD 0x20 +#define SD20_TX_NEG_EDGE 0x00 +#define SD20_TX_14_AHEAD 0x10 +#define SD20_TX_SEL_MASK 0x10 +#define DDR_VAR_SDCLK_POL_SWAP 0x01 #define SD_CMD0 0xFDA9 #define SD_CMD_START 0x40 #define SD_CMD1 0xFDAA @@ -569,14 +288,46 @@ #define SD_BLOCK_CNT_L 0xFDB1 #define SD_BLOCK_CNT_H 0xFDB2 #define SD_TRANSFER 0xFDB3 +#define SD_TRANSFER_START 0x80 +#define SD_TRANSFER_END 0x40 +#define SD_STAT_IDLE 0x20 +#define SD_TRANSFER_ERR 0x10 +#define SD_TM_NORMAL_WRITE 0x00 +#define SD_TM_AUTO_WRITE_3 0x01 +#define SD_TM_AUTO_WRITE_4 0x02 +#define SD_TM_AUTO_READ_3 0x05 +#define SD_TM_AUTO_READ_4 0x06 +#define SD_TM_CMD_RSP 0x08 +#define SD_TM_AUTO_WRITE_1 0x09 +#define SD_TM_AUTO_WRITE_2 0x0A +#define SD_TM_NORMAL_READ 0x0C +#define SD_TM_AUTO_READ_1 0x0D +#define SD_TM_AUTO_READ_2 0x0E +#define SD_TM_AUTO_TUNING 0x0F #define SD_CMD_STATE 0xFDB5 +#define SD_CMD_IDLE 0x80 + #define SD_DATA_STATE 0xFDB6 +#define SD_DATA_IDLE 0x80 #define SRCTL 0xFC13 #define DCM_DRP_CTL 0xFC23 +#define DCM_RESET 0x08 +#define DCM_LOCKED 0x04 +#define DCM_208M 0x00 +#define DCM_TX 0x01 +#define DCM_RX 0x02 #define DCM_DRP_TRIG 0xFC24 +#define DRP_START 0x80 +#define DRP_DONE 0x40 #define DCM_DRP_CFG 0xFC25 +#define DRP_WRITE 0x80 +#define DRP_READ 0x00 +#define DCM_WRITE_ADDRESS_50 0x50 +#define DCM_WRITE_ADDRESS_51 0x51 +#define DCM_READ_ADDRESS_00 0x00 +#define DCM_READ_ADDRESS_51 0x51 #define DCM_DRP_WR_DATA_L 0xFC26 #define DCM_DRP_WR_DATA_H 0xFC27 #define DCM_DRP_RD_DATA_L 0xFC28 @@ -587,42 +338,153 @@ #define SD_DCMPS1_CTL 0xFC2D #define SD_VPTX_CTL SD_VPCLK0_CTL #define SD_VPRX_CTL SD_VPCLK1_CTL +#define PHASE_CHANGE 0x80 +#define PHASE_NOT_RESET 0x40 #define SD_DCMPS_TX_CTL SD_DCMPS0_CTL #define SD_DCMPS_RX_CTL SD_DCMPS1_CTL +#define DCMPS_CHANGE 0x80 +#define DCMPS_CHANGE_DONE 0x40 +#define DCMPS_ERROR 0x20 +#define DCMPS_CURRENT_PHASE 0x1F #define CARD_CLK_SOURCE 0xFC2E - +#define CRC_FIX_CLK (0x00 << 0) +#define CRC_VAR_CLK0 (0x01 << 0) +#define CRC_VAR_CLK1 (0x02 << 0) +#define SD30_FIX_CLK (0x00 << 2) +#define SD30_VAR_CLK0 (0x01 << 2) +#define SD30_VAR_CLK1 (0x02 << 2) +#define SAMPLE_FIX_CLK (0x00 << 4) +#define SAMPLE_VAR_CLK0 (0x01 << 4) +#define SAMPLE_VAR_CLK1 (0x02 << 4) #define CARD_PWR_CTL 0xFD50 +#define PMOS_STRG_MASK 0x10 +#define PMOS_STRG_800mA 0x10 +#define PMOS_STRG_400mA 0x00 +#define SD_POWER_OFF 0x03 +#define SD_PARTIAL_POWER_ON 0x01 +#define SD_POWER_ON 0x00 +#define SD_POWER_MASK 0x03 +#define MS_POWER_OFF 0x0C +#define MS_PARTIAL_POWER_ON 0x04 +#define MS_POWER_ON 0x00 +#define MS_POWER_MASK 0x0C +#define BPP_POWER_OFF 0x0F +#define BPP_POWER_5_PERCENT_ON 0x0E +#define BPP_POWER_10_PERCENT_ON 0x0C +#define BPP_POWER_15_PERCENT_ON 0x08 +#define BPP_POWER_ON 0x00 +#define BPP_POWER_MASK 0x0F +#define SD_VCC_PARTIAL_POWER_ON 0x02 +#define SD_VCC_POWER_ON 0x00 #define CARD_CLK_SWITCH 0xFD51 #define RTL8411B_PACKAGE_MODE 0xFD51 #define CARD_SHARE_MODE 0xFD52 +#define CARD_SHARE_MASK 0x0F +#define CARD_SHARE_MULTI_LUN 0x00 +#define CARD_SHARE_NORMAL 0x00 +#define CARD_SHARE_48_SD 0x04 +#define CARD_SHARE_48_MS 0x08 +#define CARD_SHARE_BAROSSA_SD 0x01 +#define CARD_SHARE_BAROSSA_MS 0x02 #define CARD_DRIVE_SEL 0xFD53 +#define MS_DRIVE_8mA (0x01 << 6) +#define MMC_DRIVE_8mA (0x01 << 4) +#define XD_DRIVE_8mA (0x01 << 2) +#define GPIO_DRIVE_8mA 0x01 +#define RTS5209_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\ + XD_DRIVE_8mA | GPIO_DRIVE_8mA) +#define RTL8411_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | MMC_DRIVE_8mA |\ + XD_DRIVE_8mA) +#define RTSX_CARD_DRIVE_DEFAULT (MS_DRIVE_8mA | GPIO_DRIVE_8mA) + #define CARD_STOP 0xFD54 +#define SPI_STOP 0x01 +#define XD_STOP 0x02 +#define SD_STOP 0x04 +#define MS_STOP 0x08 +#define SPI_CLR_ERR 0x10 +#define XD_CLR_ERR 0x20 +#define SD_CLR_ERR 0x40 +#define MS_CLR_ERR 0x80 #define CARD_OE 0xFD55 +#define SD_OUTPUT_EN 0x04 +#define MS_OUTPUT_EN 0x08 #define CARD_AUTO_BLINK 0xFD56 #define CARD_GPIO_DIR 0xFD57 #define CARD_GPIO 0xFD58 #define CARD_DATA_SOURCE 0xFD5B +#define PINGPONG_BUFFER 0x01 +#define RING_BUFFER 0x00 #define SD30_CLK_DRIVE_SEL 0xFD5A +#define DRIVER_TYPE_A 0x05 +#define DRIVER_TYPE_B 0x03 +#define DRIVER_TYPE_C 0x02 +#define DRIVER_TYPE_D 0x01 #define CARD_SELECT 0xFD5C +#define SD_MOD_SEL 2 +#define MS_MOD_SEL 3 #define SD30_DRIVE_SEL 0xFD5E +#define CFG_DRIVER_TYPE_A 0x02 +#define CFG_DRIVER_TYPE_B 0x03 +#define CFG_DRIVER_TYPE_C 0x01 +#define CFG_DRIVER_TYPE_D 0x00 #define SD30_CMD_DRIVE_SEL 0xFD5E #define SD30_DAT_DRIVE_SEL 0xFD5F #define CARD_CLK_EN 0xFD69 +#define SD_CLK_EN 0x04 +#define MS_CLK_EN 0x08 #define SDIO_CTRL 0xFD6B #define CD_PAD_CTL 0xFD73 - +#define CD_DISABLE_MASK 0x07 +#define MS_CD_DISABLE 0x04 +#define SD_CD_DISABLE 0x02 +#define XD_CD_DISABLE 0x01 +#define CD_DISABLE 0x07 +#define CD_ENABLE 0x00 +#define MS_CD_EN_ONLY 0x03 +#define SD_CD_EN_ONLY 0x05 +#define XD_CD_EN_ONLY 0x06 +#define FORCE_CD_LOW_MASK 0x38 +#define FORCE_CD_XD_LOW 0x08 +#define FORCE_CD_SD_LOW 0x10 +#define FORCE_CD_MS_LOW 0x20 +#define CD_AUTO_DISABLE 0x40 #define FPDCTL 0xFC00 +#define SSC_POWER_DOWN 0x01 +#define SD_OC_POWER_DOWN 0x02 +#define ALL_POWER_DOWN 0x07 +#define OC_POWER_DOWN 0x06 #define PDINFO 0xFC01 #define CLK_CTL 0xFC02 +#define CHANGE_CLK 0x01 +#define CLK_LOW_FREQ 0x01 + #define CLK_DIV 0xFC03 +#define CLK_DIV_1 0x01 +#define CLK_DIV_2 0x02 +#define CLK_DIV_4 0x03 +#define CLK_DIV_8 0x04 #define CLK_SEL 0xFC04 #define SSC_DIV_N_0 0xFC0F #define SSC_DIV_N_1 0xFC10 #define SSC_CTL1 0xFC11 +#define SSC_RSTB 0x80 +#define SSC_8X_EN 0x40 +#define SSC_FIX_FRAC 0x20 +#define SSC_SEL_1M 0x00 +#define SSC_SEL_2M 0x08 +#define SSC_SEL_4M 0x10 +#define SSC_SEL_8M 0x18 #define SSC_CTL2 0xFC12 - +#define SSC_DEPTH_MASK 0x07 +#define SSC_DEPTH_DISALBE 0x00 +#define SSC_DEPTH_4M 0x01 +#define SSC_DEPTH_2M 0x02 +#define SSC_DEPTH_1M 0x03 +#define SSC_DEPTH_500K 0x04 +#define SSC_DEPTH_250K 0x05 #define RCCTL 0xFC14 #define FPGA_PULL_CTL 0xFC1D @@ -630,6 +492,24 @@ #define GPIO_CTL 0xFC1F #define LDO_CTL 0xFC1E +#define BPP_ASIC_1V7 0x00 +#define BPP_ASIC_1V8 0x01 +#define BPP_ASIC_1V9 0x02 +#define BPP_ASIC_2V0 0x03 +#define BPP_ASIC_2V7 0x04 +#define BPP_ASIC_2V8 0x05 +#define BPP_ASIC_3V2 0x06 +#define BPP_ASIC_3V3 0x07 +#define BPP_REG_TUNED18 0x07 +#define BPP_TUNED18_SHIFT_8402 5 +#define BPP_TUNED18_SHIFT_8411 4 +#define BPP_PAD_MASK 0x04 +#define BPP_PAD_3V3 0x04 +#define BPP_PAD_1V8 0x00 +#define BPP_LDO_POWB 0x03 +#define BPP_LDO_ON 0x00 +#define BPP_LDO_SUSPEND 0x02 +#define BPP_LDO_OFF 0x03 #define SYS_VER 0xFC32 #define CARD_PULL_CTL1 0xFD60 @@ -642,6 +522,10 @@ /* PCI Express Related Registers */ #define IRQEN0 0xFE20 #define IRQSTAT0 0xFE21 +#define DMA_DONE_INT 0x80 +#define SUSPEND_INT 0x40 +#define LINK_RDY_INT 0x20 +#define LINK_DOWN_INT 0x10 #define IRQEN1 0xFE22 #define IRQSTAT1 0xFE23 #define TLPRIEN 0xFE24 @@ -653,6 +537,16 @@ #define DMATC2 0xFE2A #define DMATC3 0xFE2B #define DMACTL 0xFE2C +#define DMA_RST 0x80 +#define DMA_BUSY 0x04 +#define DMA_DIR_TO_CARD 0x00 +#define DMA_DIR_FROM_CARD 0x02 +#define DMA_EN 0x01 +#define DMA_128 (0 << 4) +#define DMA_256 (1 << 4) +#define DMA_512 (2 << 4) +#define DMA_1024 (3 << 4) +#define DMA_PACK_SIZE_MASK 0x30 #define BCTL 0xFE2D #define RBBC0 0xFE2E #define RBBC1 0xFE2F @@ -693,11 +587,19 @@ #define RESET_LOAD_REG 0xFE5E #define EFUSE_CONTENT 0xFE5F #define HOST_SLEEP_STATE 0xFE60 +#define HOST_ENTER_S1 1 +#define HOST_ENTER_S3 2 + #define SDIO_CFG 0xFE70 #define NFTS_TX_CTRL 0xFE72 #define PWR_GATE_CTRL 0xFE75 +#define PWR_GATE_EN 0x01 +#define LDO3318_PWR_MASK 0x06 +#define LDO_ON 0x00 +#define LDO_SUSPEND 0x04 +#define LDO_OFF 0x06 #define PWD_SUSPEND_EN 0xFE76 #define LDO_PWR_SEL 0xFE78 -- 1.9.1 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
