From: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
Signed-off-by: Jes Sorensen <Jes.Sorensen@xxxxxxxxxx>
---
drivers/staging/rtl8723au/include/Hal8723PwrSeq.h | 40 +++++++----------------
1 file changed, 11 insertions(+), 29 deletions(-)
diff --git a/drivers/staging/rtl8723au/include/Hal8723PwrSeq.h b/drivers/staging/rtl8723au/include/Hal8723PwrSeq.h
index d2c1ff2..fe76221 100644
--- a/drivers/staging/rtl8723au/include/Hal8723PwrSeq.h
+++ b/drivers/staging/rtl8723au/include/Hal8723PwrSeq.h
@@ -39,10 +39,10 @@
* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, comments here
*/
#define RTL8723A_TRANS_CARDEMU_TO_ACT \
- {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
- {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
- {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \
- {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, /*0x00[5] = 1b'0 release analog Ips to digital , 1:isolation*/ \
+ {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
+ {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \
+ {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \
+ {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, /*0x00[5] = 1b'0 release analog Ips to digital , 1:isolation*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},/* disable SW LPS 0x04[10]= 0*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]= 1*/ \
@@ -57,44 +57,28 @@
{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
- {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, /*0x00[5] = 1b'1 analog Ips to digital , 1:isolation*/ \
- {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \
+ {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, /*0x00[5] = 1b'1 analog Ips to digital , 1:isolation*/ \
+ {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \
#define RTL8723A_TRANS_CARDEMU_TO_SUS \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
- {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/
#define RTL8723A_TRANS_SUS_TO_CARDEMU \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \
- {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
- {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
+ {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/
#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU \
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \
- {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\
{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \
- {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/
-
+ {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
#define RTL8723A_TRANS_CARDEMU_TO_PDN \
- {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \
- {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
+ {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \
{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
@@ -112,11 +96,9 @@
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \
{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \
{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \
- {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \
{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/
#define RTL8723A_TRANS_LPS_TO_ACT \
- {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\
--
1.9.3
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
