Fix two reported bugs, caused by et131x_adapter->phydev->addr being accessed before it is initialised, by: - letting et131x_mii_write() take a phydev address, instead of using the one stored in adapter by default. This is so et131x_mdio_write() can use it's own addr value. - removing implementation of et131x_mdio_reset(), as it's not needed. - moving a call to et131x_disable_phy_coma() in et131x_pci_setup(), which uses phydev->addr, until after the mdiobus has been registered. Link: https://bugzilla.kernel.org/show_bug.cgi?id=80751 Link: https://bugzilla.kernel.org/show_bug.cgi?id=77121 Cc: stable@xxxxxxxxxxxxxxx Signed-off-by: Mark Einon <mark.einon@xxxxxxxxx> --- drivers/staging/et131x/et131x.c | 68 ++++++++++++++++------------------------- 1 file changed, 27 insertions(+), 41 deletions(-) diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c index 8bf1eb4..831b7c6 100644 --- a/drivers/staging/et131x/et131x.c +++ b/drivers/staging/et131x/et131x.c @@ -1421,22 +1421,16 @@ static int et131x_mii_read(struct et131x_adapter *adapter, u8 reg, u16 *value) * @reg: the register to read * @value: 16-bit value to write */ -static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value) +static int et131x_mii_write(struct et131x_adapter *adapter, u8 addr, u8 reg, + u16 value) { struct mac_regs __iomem *mac = &adapter->regs->mac; - struct phy_device *phydev = adapter->phydev; int status = 0; - u8 addr; u32 delay = 0; u32 mii_addr; u32 mii_cmd; u32 mii_indicator; - if (!phydev) - return -EIO; - - addr = phydev->addr; - /* Save a local copy of the registers we are dealing with so we can * set them back */ @@ -1631,17 +1625,7 @@ static int et131x_mdio_write(struct mii_bus *bus, int phy_addr, struct net_device *netdev = bus->priv; struct et131x_adapter *adapter = netdev_priv(netdev); - return et131x_mii_write(adapter, reg, value); -} - -static int et131x_mdio_reset(struct mii_bus *bus) -{ - struct net_device *netdev = bus->priv; - struct et131x_adapter *adapter = netdev_priv(netdev); - - et131x_mii_write(adapter, MII_BMCR, BMCR_RESET); - - return 0; + return et131x_mii_write(adapter, phy_addr, reg, value); } /* et1310_phy_power_switch - PHY power control @@ -1656,18 +1640,20 @@ static int et131x_mdio_reset(struct mii_bus *bus) static void et1310_phy_power_switch(struct et131x_adapter *adapter, bool down) { u16 data; + struct phy_device *phydev = adapter->phydev; et131x_mii_read(adapter, MII_BMCR, &data); data &= ~BMCR_PDOWN; if (down) data |= BMCR_PDOWN; - et131x_mii_write(adapter, MII_BMCR, data); + et131x_mii_write(adapter, phydev->addr, MII_BMCR, data); } /* et131x_xcvr_init - Init the phy if we are setting it into force mode */ static void et131x_xcvr_init(struct et131x_adapter *adapter) { u16 lcr2; + struct phy_device *phydev = adapter->phydev; /* Set the LED behavior such that LED 1 indicates speed (off = * 10Mbits, blink = 100Mbits, on = 1000Mbits) and LED 2 indicates @@ -1688,7 +1674,7 @@ static void et131x_xcvr_init(struct et131x_adapter *adapter) else lcr2 |= (LED_VAL_LINKON << LED_TXRX_SHIFT); - et131x_mii_write(adapter, PHY_LED_2, lcr2); + et131x_mii_write(adapter, phydev->addr, PHY_LED_2, lcr2); } } @@ -3643,14 +3629,14 @@ static void et131x_adjust_link(struct net_device *netdev) et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG, ®ister18); - et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG, - register18 | 0x4); - et131x_mii_write(adapter, PHY_INDEX_REG, + et131x_mii_write(adapter, phydev->addr, + PHY_MPHY_CONTROL_REG, register18 | 0x4); + et131x_mii_write(adapter, phydev->addr, PHY_INDEX_REG, register18 | 0x8402); - et131x_mii_write(adapter, PHY_DATA_REG, + et131x_mii_write(adapter, phydev->addr, PHY_DATA_REG, register18 | 511); - et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG, - register18); + et131x_mii_write(adapter, phydev->addr, + PHY_MPHY_CONTROL_REG, register18); } et1310_config_flow_control(adapter); @@ -3662,7 +3648,8 @@ static void et131x_adjust_link(struct net_device *netdev) et131x_mii_read(adapter, PHY_CONFIG, ®); reg &= ~ET_PHY_CONFIG_TX_FIFO_DEPTH; reg |= ET_PHY_CONFIG_FIFO_DEPTH_32; - et131x_mii_write(adapter, PHY_CONFIG, reg); + et131x_mii_write(adapter, phydev->addr, PHY_CONFIG, + reg); } et131x_set_rx_dma_timer(adapter); @@ -3675,14 +3662,14 @@ static void et131x_adjust_link(struct net_device *netdev) et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG, ®ister18); - et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG, - register18 | 0x4); - et131x_mii_write(adapter, PHY_INDEX_REG, - register18 | 0x8402); - et131x_mii_write(adapter, PHY_DATA_REG, - register18 | 511); - et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG, - register18); + et131x_mii_write(adapter, phydev->addr, + PHY_MPHY_CONTROL_REG, register18 | 0x4); + et131x_mii_write(adapter, phydev->addr, + PHY_INDEX_REG, register18 | 0x8402); + et131x_mii_write(adapter, phydev->addr, + PHY_DATA_REG, register18 | 511); + et131x_mii_write(adapter, phydev->addr, + PHY_MPHY_CONTROL_REG, register18); } /* Free the packets being actively sent & stopped */ @@ -4644,10 +4631,6 @@ static int et131x_pci_setup(struct pci_dev *pdev, /* Copy address into the net_device struct */ memcpy(netdev->dev_addr, adapter->addr, ETH_ALEN); - /* Init variable for counting how long we do not have link status */ - adapter->boot_coma = 0; - et1310_disable_phy_coma(adapter); - rc = -ENOMEM; /* Setup the mii_bus struct */ @@ -4663,7 +4646,6 @@ static int et131x_pci_setup(struct pci_dev *pdev, adapter->mii_bus->priv = netdev; adapter->mii_bus->read = et131x_mdio_read; adapter->mii_bus->write = et131x_mdio_write; - adapter->mii_bus->reset = et131x_mdio_reset; adapter->mii_bus->irq = kmalloc_array(PHY_MAX_ADDR, sizeof(int), GFP_KERNEL); if (!adapter->mii_bus->irq) @@ -4687,6 +4669,10 @@ static int et131x_pci_setup(struct pci_dev *pdev, /* Setup et1310 as per the documentation */ et131x_adapter_setup(adapter); + /* Init variable for counting how long we do not have link status */ + adapter->boot_coma = 0; + et1310_disable_phy_coma(adapter); + /* We can enable interrupts now * * NOTE - Because registration of interrupt handler is done in the -- 2.0.1 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
