Added spaces needed in the proper places to address:
ERROR: space required after that ',' (ctx:VxV)
ERROR: space required after that ';' (ctx:VxV)
ERROR: space required after that close brace '}'
ERROR: space required before the open brace '{'
ERROR: space required before the open parenthesis '('
ERROR: spaces required around that '<' (ctx:VxV)
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: spaces required around that '==' (ctx:VxV)
Signed-off-by: Chaitanya Hazarey <c@xxxxx>
---
drivers/staging/rtl8192u/r8180_93cx6.c | 46 +++++++++++++++++-----------------
1 file changed, 23 insertions(+), 23 deletions(-)
diff --git a/drivers/staging/rtl8192u/r8180_93cx6.c b/drivers/staging/rtl8192u/r8180_93cx6.c
index cd06054..fb8a7a8 100644
--- a/drivers/staging/rtl8192u/r8180_93cx6.c
+++ b/drivers/staging/rtl8192u/r8180_93cx6.c
@@ -53,7 +53,7 @@ static void eprom_ck_cycle(struct net_device *dev)
}
-static void eprom_w(struct net_device *dev,short bit)
+static void eprom_w(struct net_device *dev, short bit)
{
u8 cmdreg;
@@ -86,7 +86,7 @@ static void eprom_send_bits_string(struct net_device *dev, short b[], int len)
{
int i;
- for(i=0; i<len; i++){
+ for (i = 0; i < len; i++) {
eprom_w(dev, b[i]);
eprom_ck_cycle(dev);
}
@@ -96,37 +96,37 @@ static void eprom_send_bits_string(struct net_device *dev, short b[], int len)
u32 eprom_read(struct net_device *dev, u32 addr)
{
struct r8192_priv *priv = ieee80211_priv(dev);
- short read_cmd[]={1,1,0};
+ short read_cmd[] = {1, 1, 0};
short addr_str[8];
int i;
int addr_len;
u32 ret;
- ret=0;
+ ret = 0;
//enable EPROM programming
write_nic_byte_E(dev, EPROM_CMD,
(EPROM_CMD_PROGRAM<<EPROM_CMD_OPERATING_MODE_SHIFT));
force_pci_posting(dev);
udelay(EPROM_DELAY);
- if (priv->epromtype==EPROM_93c56){
- addr_str[7]=addr & 1;
- addr_str[6]=addr & (1<<1);
- addr_str[5]=addr & (1<<2);
- addr_str[4]=addr & (1<<3);
- addr_str[3]=addr & (1<<4);
- addr_str[2]=addr & (1<<5);
- addr_str[1]=addr & (1<<6);
- addr_str[0]=addr & (1<<7);
- addr_len=8;
- }else{
- addr_str[5]=addr & 1;
- addr_str[4]=addr & (1<<1);
- addr_str[3]=addr & (1<<2);
- addr_str[2]=addr & (1<<3);
- addr_str[1]=addr & (1<<4);
- addr_str[0]=addr & (1<<5);
- addr_len=6;
+ if (priv->epromtype == EPROM_93c56) {
+ addr_str[7] = addr & 1;
+ addr_str[6] = addr & (1<<1);
+ addr_str[5] = addr & (1<<2);
+ addr_str[4] = addr & (1<<3);
+ addr_str[3] = addr & (1<<4);
+ addr_str[2] = addr & (1<<5);
+ addr_str[1] = addr & (1<<6);
+ addr_str[0] = addr & (1<<7);
+ addr_len = 8;
+ } else {
+ addr_str[5] = addr & 1;
+ addr_str[4] = addr & (1<<1);
+ addr_str[3] = addr & (1<<2);
+ addr_str[2] = addr & (1<<3);
+ addr_str[1] = addr & (1<<4);
+ addr_str[0] = addr & (1<<5);
+ addr_len = 6;
}
eprom_cs(dev, 1);
eprom_ck_cycle(dev);
@@ -137,7 +137,7 @@ u32 eprom_read(struct net_device *dev, u32 addr)
//I'm unsure if it is necessary, but anyway shouldn't hurt
eprom_w(dev, 0);
- for(i=0;i<16;i++){
+ for (i = 0; i < 16; i++) {
//eeprom needs a clk cycle between writing opcode&adr
//and reading data. (eeprom outs a dummy 0)
eprom_ck_cycle(dev);
--
1.9.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
