From: H Hartley Sweeten <hartleys@xxxxxxxxxxxxxxxxxxx>
For aesthetics, convert the various enums into simple defines to
describe the register map for the board. Group the bit defines with
the associated register define. Convert the helper functions for
the register bit/shift/mask stuff into simple defines.
Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx>
Cc: Ian Abbott <abbotti@xxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/staging/comedi/drivers/gsc_hpdi.c | 198 +++++++++++++-----------------
1 file changed, 82 insertions(+), 116 deletions(-)
diff --git a/drivers/staging/comedi/drivers/gsc_hpdi.c b/drivers/staging/comedi/drivers/gsc_hpdi.c
index 0770ad1..f95724a 100644
--- a/drivers/staging/comedi/drivers/gsc_hpdi.c
+++ b/drivers/staging/comedi/drivers/gsc_hpdi.c
@@ -52,115 +52,80 @@
#include "plx9080.h"
#include "comedi_fc.h"
-#define TIMER_BASE 50 /* 20MHz master clock */
-#define DMA_BUFFER_SIZE 0x10000
-#define NUM_DMA_BUFFERS 4
-#define NUM_DMA_DESCRIPTORS 256
-
-enum hpdi_registers {
- FIRMWARE_REV_REG = 0x0,
- BOARD_CONTROL_REG = 0x4,
- BOARD_STATUS_REG = 0x8,
- TX_PROG_ALMOST_REG = 0xc,
- RX_PROG_ALMOST_REG = 0x10,
- FEATURES_REG = 0x14,
- FIFO_REG = 0x18,
- TX_STATUS_COUNT_REG = 0x1c,
- TX_LINE_VALID_COUNT_REG = 0x20,
- TX_LINE_INVALID_COUNT_REG = 0x24,
- RX_STATUS_COUNT_REG = 0x28,
- RX_LINE_COUNT_REG = 0x2c,
- INTERRUPT_CONTROL_REG = 0x30,
- INTERRUPT_STATUS_REG = 0x34,
- TX_CLOCK_DIVIDER_REG = 0x38,
- TX_FIFO_SIZE_REG = 0x40,
- RX_FIFO_SIZE_REG = 0x44,
- TX_FIFO_WORDS_REG = 0x48,
- RX_FIFO_WORDS_REG = 0x4c,
- INTERRUPT_EDGE_LEVEL_REG = 0x50,
- INTERRUPT_POLARITY_REG = 0x54,
-};
-
-/* bit definitions */
-
-enum firmware_revision_bits {
- FEATURES_REG_PRESENT_BIT = 0x8000,
-};
-
-enum board_control_bits {
- BOARD_RESET_BIT = 0x1, /* wait 10usec before accessing fifos */
- TX_FIFO_RESET_BIT = 0x2,
- RX_FIFO_RESET_BIT = 0x4,
- TX_ENABLE_BIT = 0x10,
- RX_ENABLE_BIT = 0x20,
- DEMAND_DMA_DIRECTION_TX_BIT = 0x40,
- /* for ch 0, ch 1 can only transmit (when present) */
- LINE_VALID_ON_STATUS_VALID_BIT = 0x80,
- START_TX_BIT = 0x10,
- CABLE_THROTTLE_ENABLE_BIT = 0x20,
- TEST_MODE_ENABLE_BIT = 0x80000000,
-};
-
-enum board_status_bits {
- COMMAND_LINE_STATUS_MASK = 0x7f,
- TX_IN_PROGRESS_BIT = 0x80,
- TX_NOT_EMPTY_BIT = 0x100,
- TX_NOT_ALMOST_EMPTY_BIT = 0x200,
- TX_NOT_ALMOST_FULL_BIT = 0x400,
- TX_NOT_FULL_BIT = 0x800,
- RX_NOT_EMPTY_BIT = 0x1000,
- RX_NOT_ALMOST_EMPTY_BIT = 0x2000,
- RX_NOT_ALMOST_FULL_BIT = 0x4000,
- RX_NOT_FULL_BIT = 0x8000,
- BOARD_JUMPER0_INSTALLED_BIT = 0x10000,
- BOARD_JUMPER1_INSTALLED_BIT = 0x20000,
- TX_OVERRUN_BIT = 0x200000,
- RX_UNDERRUN_BIT = 0x400000,
- RX_OVERRUN_BIT = 0x800000,
-};
-
-static uint32_t almost_full_bits(unsigned int num_words)
-{
- /* XXX need to add or subtract one? */
- return (num_words << 16) & 0xff0000;
-}
-
-static uint32_t almost_empty_bits(unsigned int num_words)
-{
- return num_words & 0xffff;
-}
-
-enum features_bits {
- FIFO_SIZE_PRESENT_BIT = 0x1,
- FIFO_WORDS_PRESENT_BIT = 0x2,
- LEVEL_EDGE_INTERRUPTS_PRESENT_BIT = 0x4,
- GPIO_SUPPORTED_BIT = 0x8,
- PLX_DMA_CH1_SUPPORTED_BIT = 0x10,
- OVERRUN_UNDERRUN_SUPPORTED_BIT = 0x20,
-};
-
-enum interrupt_sources {
- FRAME_VALID_START_INTR = 0,
- FRAME_VALID_END_INTR = 1,
- TX_FIFO_EMPTY_INTR = 8,
- TX_FIFO_ALMOST_EMPTY_INTR = 9,
- TX_FIFO_ALMOST_FULL_INTR = 10,
- TX_FIFO_FULL_INTR = 11,
- RX_EMPTY_INTR = 12,
- RX_ALMOST_EMPTY_INTR = 13,
- RX_ALMOST_FULL_INTR = 14,
- RX_FULL_INTR = 15,
-};
-
-static uint32_t intr_bit(int interrupt_source)
-{
- return 0x1 << interrupt_source;
-}
-
-static unsigned int fifo_size(uint32_t fifo_size_bits)
-{
- return fifo_size_bits & 0xfffff;
-}
+/*
+ * PCI BAR2 Register map (devpriv->mmio)
+ */
+#define FIRMWARE_REV_REG 0x00
+#define FEATURES_REG_PRESENT_BIT (1 << 15)
+#define BOARD_CONTROL_REG 0x04
+#define BOARD_RESET_BIT (1 << 0)
+#define TX_FIFO_RESET_BIT (1 << 1)
+#define RX_FIFO_RESET_BIT (1 << 2)
+#define TX_ENABLE_BIT (1 << 4)
+#define RX_ENABLE_BIT (1 << 5)
+#define DEMAND_DMA_DIRECTION_TX_BIT (1 << 6) /* ch 0 only */
+#define LINE_VALID_ON_STATUS_VALID_BIT (1 << 7)
+#define START_TX_BIT (1 << 8)
+#define CABLE_THROTTLE_ENABLE_BIT (1 << 9)
+#define TEST_MODE_ENABLE_BIT (1 << 31)
+#define BOARD_STATUS_REG 0x08
+#define COMMAND_LINE_STATUS_MASK (0x7f << 0)
+#define TX_IN_PROGRESS_BIT (1 << 7)
+#define TX_NOT_EMPTY_BIT (1 << 8)
+#define TX_NOT_ALMOST_EMPTY_BIT (1 << 9)
+#define TX_NOT_ALMOST_FULL_BIT (1 << 10)
+#define TX_NOT_FULL_BIT (1 << 11)
+#define RX_NOT_EMPTY_BIT (1 << 12)
+#define RX_NOT_ALMOST_EMPTY_BIT (1 << 13)
+#define RX_NOT_ALMOST_FULL_BIT (1 << 14)
+#define RX_NOT_FULL_BIT (1 << 15)
+#define BOARD_JUMPER0_INSTALLED_BIT (1 << 16)
+#define BOARD_JUMPER1_INSTALLED_BIT (1 << 17)
+#define TX_OVERRUN_BIT (1 << 21)
+#define RX_UNDERRUN_BIT (1 << 22)
+#define RX_OVERRUN_BIT (1 << 23)
+#define TX_PROG_ALMOST_REG 0x0c
+#define RX_PROG_ALMOST_REG 0x10
+#define ALMOST_EMPTY_BITS(x) (((x) & 0xffff) << 0)
+#define ALMOST_FULL_BITS(x) (((x) & 0xff) << 16)
+#define FEATURES_REG 0x14
+#define FIFO_SIZE_PRESENT_BIT (1 << 0)
+#define FIFO_WORDS_PRESENT_BIT (1 << 1)
+#define LEVEL_EDGE_INTERRUPTS_PRESENT_BIT (1 << 2)
+#define GPIO_SUPPORTED_BIT (1 << 3)
+#define PLX_DMA_CH1_SUPPORTED_BIT (1 << 4)
+#define OVERRUN_UNDERRUN_SUPPORTED_BIT (1 << 5)
+#define FIFO_REG 0x18
+#define TX_STATUS_COUNT_REG 0x1c
+#define TX_LINE_VALID_COUNT_REG 0x20,
+#define TX_LINE_INVALID_COUNT_REG 0x24
+#define RX_STATUS_COUNT_REG 0x28
+#define RX_LINE_COUNT_REG 0x2c
+#define INTERRUPT_CONTROL_REG 0x30
+#define FRAME_VALID_START_INTR (1 << 0)
+#define FRAME_VALID_END_INTR (1 << 1)
+#define TX_FIFO_EMPTY_INTR (1 << 8)
+#define TX_FIFO_ALMOST_EMPTY_INTR (1 << 9)
+#define TX_FIFO_ALMOST_FULL_INTR (1 << 10)
+#define TX_FIFO_FULL_INTR (1 << 11)
+#define RX_EMPTY_INTR (1 << 12)
+#define RX_ALMOST_EMPTY_INTR (1 << 13)
+#define RX_ALMOST_FULL_INTR (1 << 14)
+#define RX_FULL_INTR (1 << 15)
+#define INTERRUPT_STATUS_REG 0x34
+#define TX_CLOCK_DIVIDER_REG 0x38
+#define TX_FIFO_SIZE_REG 0x40
+#define RX_FIFO_SIZE_REG 0x44
+#define FIFO_SIZE_MASK (0xfffff << 0)
+#define TX_FIFO_WORDS_REG 0x48
+#define RX_FIFO_WORDS_REG 0x4c
+#define INTERRUPT_EDGE_LEVEL_REG 0x50
+#define INTERRUPT_POLARITY_REG 0x54
+
+#define TIMER_BASE 50 /* 20MHz master clock */
+#define DMA_BUFFER_SIZE 0x10000
+#define NUM_DMA_BUFFERS 4
+#define NUM_DMA_DESCRIPTORS 256
struct hpdi_board {
const char *name; /* board name */
@@ -390,7 +355,7 @@ static int gsc_hpdi_cmd(struct comedi_device *dev,
devpriv->mmio + BOARD_STATUS_REG);
/* enable interrupts */
- writel(intr_bit(RX_FULL_INTR), devpriv->mmio + INTERRUPT_CONTROL_REG);
+ writel(RX_FULL_INTR, devpriv->mmio + INTERRUPT_CONTROL_REG);
writel(RX_ENABLE_BIT, devpriv->mmio + BOARD_CONTROL_REG);
@@ -541,18 +506,19 @@ static int gsc_hpdi_init(struct comedi_device *dev)
struct hpdi_private *devpriv = dev->private;
uint32_t plx_intcsr_bits;
+ /* wait 10usec after reset before accessing fifos */
writel(BOARD_RESET_BIT, devpriv->mmio + BOARD_CONTROL_REG);
udelay(10);
- writel(almost_empty_bits(32) | almost_full_bits(32),
+ writel(ALMOST_EMPTY_BITS(32) | ALMOST_FULL_BITS(32),
devpriv->mmio + RX_PROG_ALMOST_REG);
- writel(almost_empty_bits(32) | almost_full_bits(32),
+ writel(ALMOST_EMPTY_BITS(32) | ALMOST_FULL_BITS(32),
devpriv->mmio + TX_PROG_ALMOST_REG);
- devpriv->tx_fifo_size = fifo_size(readl(devpriv->mmio +
- TX_FIFO_SIZE_REG));
- devpriv->rx_fifo_size = fifo_size(readl(devpriv->mmio +
- RX_FIFO_SIZE_REG));
+ devpriv->tx_fifo_size = readl(devpriv->mmio + TX_FIFO_SIZE_REG) &
+ FIFO_SIZE_MASK;
+ devpriv->rx_fifo_size = readl(devpriv->mmio + RX_FIFO_SIZE_REG) &
+ FIFO_SIZE_MASK;
writel(0, devpriv->mmio + INTERRUPT_CONTROL_REG);
--
1.8.5.2
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
