Nudge the commenting in this mess a little further from 'bad.' Much of
it was incorrectly indented.
Another sed cleanup:
$ sed -i -e '/\/\*\*\*\*\*\*\*\*\**\//,1d' addi-data/hwdrv_apci1500.c
Signed-off-by: Conrad Meyer <cse.cem@xxxxxxxxx>
---
.../comedi/drivers/addi-data/hwdrv_apci1500.c | 452 ---------------------
1 file changed, 452 deletions(-)
diff --git a/drivers/staging/comedi/drivers/addi-data/hwdrv_apci1500.c b/drivers/staging/comedi/drivers/addi-data/hwdrv_apci1500.c
index 0ccf784..4f5ce6a 100644
--- a/drivers/staging/comedi/drivers/addi-data/hwdrv_apci1500.c
+++ b/drivers/staging/comedi/drivers/addi-data/hwdrv_apci1500.c
@@ -224,48 +224,44 @@ static int i_TimerCounter1Enabled = 0, i_TimerCounter2Enabled = 0,
| used for event |
+----------------------------------------------------------------------------+
| Output Parameters : -- |
+----------------------------------------------------------------------------+
| Return Value : TRUE : No error occur |
| : FALSE : Error occur. Return the error |
| |
+----------------------------------------------------------------------------+
*/
static int i_APCI1500_ConfigDigitalInputEvent(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
int i_PatternPolarity = 0, i_PatternTransition = 0, i_PatternMask = 0;
int i_MaxChannel = 0, i_Count = 0, i_EventMask = 0;
int i_PatternTransitionCount = 0, i_RegValue;
int i;
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Disables the main interrupt on the board */
- /**********************************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if (data[0] == 1) {
i_MaxChannel = 8;
} /* if (data[0] == 1) */
else {
if (data[0] == 2) {
i_MaxChannel = 6;
} /* if(data[0]==2) */
else {
dev_warn(dev->hw_dev,
"The specified port event does not exist\n");
return -EINVAL;
} /* else if(data[0]==2) */
} /* else if (data[0] == 1) */
switch (data[1]) {
case 0:
data[1] = APCI1500_AND;
break;
case 1:
@@ -310,292 +306,238 @@ static int i_APCI1500_ConfigDigitalInputEvent(struct comedi_device *dev,
i_Count));
i_PatternTransition =
i_PatternTransition | (1 << (i_MaxChannel -
i_Count));
break;
case 4:
i_PatternTransition =
i_PatternTransition | (1 << (i_MaxChannel -
i_Count));
break;
case 5:
break;
default:
dev_warn(dev->hw_dev,
"The option indicated in the event mask does not exist\n");
return -EINVAL;
} /* switch(i_EventMask) */
} /* for (i_Count = i_MaxChannel; i_Count >0;i_Count --) */
if (data[0] == 1) {
- /****************************/
/* Test the interrupt logic */
- /****************************/
if (data[1] == APCI1500_AND ||
data[1] == APCI1500_OR ||
data[1] == APCI1500_OR_PRIORITY) {
- /**************************************/
/* Tests if a transition was declared */
/* for a OR PRIORITY logic */
- /**************************************/
if (data[1] == APCI1500_OR_PRIORITY
&& i_PatternTransition != 0) {
dev_warn(dev->hw_dev,
"Transition error on an OR PRIORITY logic\n");
return -EINVAL;
} /* if (data[1]== APCI1500_OR_PRIORITY && i_PatternTransition != 0) */
- /*************************************/
/* Tests if more than one transition */
/* was declared for an AND logic */
- /*************************************/
if (data[1] == APCI1500_AND) {
for (i_Count = 0; i_Count < 8; i_Count++) {
i_PatternTransitionCount =
i_PatternTransitionCount +
((i_PatternTransition >>
i_Count) & 0x1);
} /* for (i_Count = 0; i_Count < 8; i_Count++) */
if (i_PatternTransitionCount > 1) {
dev_warn(dev->hw_dev,
"Transition error on an AND logic\n");
return -EINVAL;
} /* if (i_PatternTransitionCount > 1) */
} /* if (data[1]== APCI1500_AND) */
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port A */
- /******************/
outb(0xF0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Selects the polarity register of port 1 */
- /**********************************************/
outb(APCI1500_RW_PORT_A_PATTERN_POLARITY,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternPolarity,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*********************************************/
/* Selects the pattern mask register of */
/* port 1 */
- /*********************************************/
outb(APCI1500_RW_PORT_A_PATTERN_MASK,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternMask,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************************/
/* Selects the pattern transition register */
/* of port 1 */
- /********************************************/
outb(APCI1500_RW_PORT_A_PATTERN_TRANSITION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternTransition,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************/
/* Selects the mode specification mask */
/* register of port 1 */
- /******************************************/
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************/
/* Selects the mode specification mask */
/* register of port 1 */
- /******************************************/
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************/
/* Port A new mode */
- /**********************/
i_RegValue = (i_RegValue & 0xF9) | data[1] | 0x9;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event1Status = 1;
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port A */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if(data[1]==APCI1500_AND||data[1]==APCI1500_OR||data[1]==APCI1500_OR_PRIORITY) */
else {
dev_warn(dev->hw_dev,
"The choice for interrupt logic does not exist\n");
return -EINVAL;
} /* else }// if(data[1]==APCI1500_AND||data[1]==APCI1500_OR||data[1]==APCI1500_OR_PRIORITY) */
} /* if (data[0]== 1) */
- /************************************/
/* Test if event setting for port 2 */
- /************************************/
if (data[0] == 2) {
- /************************/
/* Test the event logic */
- /************************/
if (data[1] == APCI1500_OR) {
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port B */
- /******************/
outb(0x74,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************/
/* Selects the mode specification mask */
/* register of port B */
- /****************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************/
/* Selects the mode specification mask */
/* register of port B */
- /******************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = i_RegValue & 0xF9;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************/
/* Selects error channels 1 and 2 */
- /**********************************/
i_PatternMask = (i_PatternMask | 0xC0);
i_PatternPolarity = (i_PatternPolarity | 0xC0);
i_PatternTransition = (i_PatternTransition | 0xC0);
- /**********************************************/
/* Selects the polarity register of port 2 */
- /**********************************************/
outb(APCI1500_RW_PORT_B_PATTERN_POLARITY,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternPolarity,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Selects the pattern transition register */
/* of port 2 */
- /**********************************************/
outb(APCI1500_RW_PORT_B_PATTERN_TRANSITION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternTransition,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Selects the pattern Mask register */
/* of port 2 */
- /**********************************************/
outb(APCI1500_RW_PORT_B_PATTERN_MASK,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_PatternMask,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************/
/* Selects the mode specification mask */
/* register of port 2 */
- /******************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************/
/* Selects the mode specification mask */
/* register of port 2 */
- /******************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = (i_RegValue & 0xF9) | 4;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event2Status = 1;
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port B */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if (data[1] == APCI1500_OR) */
else {
dev_warn(dev->hw_dev,
"The choice for interrupt logic does not exist\n");
return -EINVAL;
} /* elseif (data[1] == APCI1500_OR) */
} /* if(data[0]==2) */
return insn->n;
}
/*
+----------------------------------------------------------------------------+
| Function Name : int i_APCI1500_StartStopInputEvent |
| (struct comedi_device *dev,struct comedi_subdevice *s, |
| struct comedi_insn *insn,unsigned int *data) |
@@ -610,258 +552,190 @@ static int i_APCI1500_ConfigDigitalInputEvent(struct comedi_device *dev,
| data[1] :No of port (1 or 2)
+----------------------------------------------------------------------------+
| Output Parameters : -- |
+----------------------------------------------------------------------------+
| Return Value : TRUE : No error occur |
| : FALSE : Error occur. Return the error |
| |
+----------------------------------------------------------------------------+
*/
static int i_APCI1500_StartStopInputEvent(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
int i_Event1InterruptStatus = 0, i_Event2InterruptStatus =
0, i_RegValue;
switch (data[0]) {
case START:
- /*************************/
/* Tests the port number */
- /*************************/
if (data[1] == 1 || data[1] == 2) {
- /***************************/
/* Test if port 1 selected */
- /***************************/
if (data[1] == 1) {
- /*****************************/
/* Test if event initialised */
- /*****************************/
if (i_Event1Status == 1) {
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port A */
- /******************/
outb(0xF0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the command and status register of */
/* port 1 */
- /***************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************/
/* Allows the pattern interrupt */
- /*************************************/
outb(0xC0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port A */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event1InterruptStatus = 1;
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Authorizes the main interrupt on the board */
- /**********************************************/
outb(0xD0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if(i_Event1Status==1) */
else {
dev_warn(dev->hw_dev,
"Event 1 not initialised\n");
return -EINVAL;
} /* else if(i_Event1Status==1) */
} /* if (data[1]==1) */
if (data[1] == 2) {
if (i_Event2Status == 1) {
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port B */
- /******************/
outb(0x74,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the command and status register of */
/* port 2 */
- /***************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************/
/* Allows the pattern interrupt */
- /*************************************/
outb(0xC0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port B */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Authorizes the main interrupt on the board */
- /**********************************************/
outb(0xD0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event2InterruptStatus = 1;
} /* if(i_Event2Status==1) */
else {
dev_warn(dev->hw_dev,
"Event 2 not initialised\n");
return -EINVAL;
} /* else if(i_Event2Status==1) */
} /* if(data[1]==2) */
} /* if (data[1] == 1 || data[0] == 2) */
else {
dev_warn(dev->hw_dev,
"The port parameter is in error\n");
return -EINVAL;
} /* else if (data[1] == 1 || data[0] == 2) */
break;
case STOP:
- /*************************/
/* Tests the port number */
- /*************************/
if (data[1] == 1 || data[1] == 2) {
- /***************************/
/* Test if port 1 selected */
- /***************************/
if (data[1] == 1) {
- /*****************************/
/* Test if event initialised */
- /*****************************/
if (i_Event1Status == 1) {
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port A */
- /******************/
outb(0xF0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the command and status register of */
/* port 1 */
- /***************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************/
/* Inhibits the pattern interrupt */
- /*************************************/
outb(0xE0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port A */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event1InterruptStatus = 0;
} /* if(i_Event1Status==1) */
else {
dev_warn(dev->hw_dev,
"Event 1 not initialised\n");
return -EINVAL;
} /* else if(i_Event1Status==1) */
} /* if (data[1]==1) */
if (data[1] == 2) {
- /*****************************/
/* Test if event initialised */
- /*****************************/
if (i_Event2Status == 1) {
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************/
/* Disable Port B */
- /******************/
outb(0x74,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the command and status register of */
/* port 2 */
- /***************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************/
/* Inhibits the pattern interrupt */
- /*************************************/
outb(0xE0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************************/
/* Selects the APCI1500_RW_MASTER_CONFIGURATION_CONTROL register */
- /*****************************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************/
/* Enable Port B */
- /*****************/
outb(0xF4,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_Event2InterruptStatus = 0;
} /* if(i_Event2Status==1) */
else {
dev_warn(dev->hw_dev,
"Event 2 not initialised\n");
return -EINVAL;
} /* else if(i_Event2Status==1) */
} /* if(data[1]==2) */
} /* if (data[1] == 1 || data[1] == 2) */
else {
dev_warn(dev->hw_dev,
"The port parameter is in error\n");
return -EINVAL;
} /* else if (data[1] == 1 || data[1] == 2) */
break;
default:
@@ -883,179 +757,161 @@ static int i_APCI1500_StartStopInputEvent(struct comedi_device *dev,
+----------------------------------------------------------------------------+
| Input Parameters : struct comedi_device *dev : Driver handle |
| unsigned int ui_Channel : Channel number to read |
| unsigned int *data : Data Pointer to read status |
+----------------------------------------------------------------------------+
| Output Parameters : -- |
+----------------------------------------------------------------------------+
| Return Value : TRUE : No error occur |
| : FALSE : Error occur. Return the error |
| |
+----------------------------------------------------------------------------+
*/
static int i_APCI1500_Initialisation(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
int i_DummyRead = 0;
- /******************/
/* Software reset */
- /******************/
i_DummyRead = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_DummyRead = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(1, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the master configuration control register */
- /*****************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0xF4, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the mode specification register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0x10, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data path polarity register of port A */
outb(APCI1500_RW_PORT_A_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* High level of port A means 1 */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port A */
outb(APCI1500_RW_PORT_A_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port A */
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port A */
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of port A: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the handshake specification register of port A */
outb(APCI1500_RW_PORT_A_HANDSHAKE_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes the register */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the mode specification register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0x10, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data path polarity register of port B */
outb(APCI1500_RW_PORT_B_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* A high level of port B means 1 */
outb(0x7F, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port B */
outb(APCI1500_RW_PORT_B_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port B */
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port B */
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of port B: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the handshake specification register of port B */
outb(APCI1500_RW_PORT_B_HANDSHAKE_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes the register */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the data path polarity register of port C */
- /*****************************************************/
outb(APCI1500_RW_PORT_C_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* High level of port C means 1 */
outb(0x9, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port C */
outb(APCI1500_RW_PORT_C_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs except channel 1 */
outb(0x0E, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the special IO register of port C */
outb(APCI1500_RW_PORT_C_SPECIAL_IO_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes it */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 1 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of timer 1 */
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of timer 1 */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 2 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of timer 2 */
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates Timer 2 interrupt management: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 3 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of Timer 3 */
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates interrupt management of timer 3: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes all interrupts */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
return insn->n;
}
static int apci1500_di_insn_bits(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
data[1] = inw(devpriv->i_IobaseAddon + APCI1500_DIGITAL_IP);
return insn->n;
}
/*
@@ -1351,157 +1207,125 @@ static int i_APCI1500_ConfigCounterTimerWatchdog(struct comedi_device *dev,
dev_warn(dev->hw_dev,
"This choice is not a timer nor a counter\n");
return -EINVAL;
} /* switch(data[2]) */
/* Selecting single or continuous mode */
switch (data[4]) {
case 0:
data[4] = APCI1500_CONTINUOUS;
break;
case 1:
data[4] = APCI1500_SINGLE;
break;
default:
dev_warn(dev->hw_dev,
"This option for single/continuous mode does not exist\n");
return -EINVAL;
} /* switch(data[4]) */
i_TimerCounterMode = data[2] | data[4] | 7;
- /*************************/
/* Test the reload value */
- /*************************/
if ((data[3] >= 0) && (data[3] <= 65535)) {
if (data[7] == APCI1500_ENABLE
|| data[7] == APCI1500_DISABLE) {
- /************************************************/
/* Selects the mode register of timer/counter 1 */
- /************************************************/
outb(APCI1500_RW_CPT_TMR1_MODE_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************/
/* Writes the new mode */
- /***********************/
outb(i_TimerCounterMode,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of timer/counter 1 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR1_TIME_CST_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************/
/* Writes the low value */
- /*************************/
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of timer/counter 1 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR1_TIME_CST_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**************************/
/* Writes the high value */
- /**************************/
data[3] = data[3] >> 8;
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************/
/* Reads the register */
- /**********************/
i_MasterConfiguration =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************************************/
/* Enables timer/counter 1 and triggers timer/counter 1 */
- /********************************************************/
i_MasterConfiguration =
i_MasterConfiguration | 0x40;
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************/
/* Writes the new configuration */
- /********************************/
outb(i_MasterConfiguration,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************/
/* Selects the commands register of */
/* timer/counter 1 */
- /****************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************/
/* Disable timer/counter 1 */
- /***************************/
outb(0x0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************/
/* Selects the commands register of */
/* timer/counter 1 */
- /****************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************/
/* Trigger timer/counter 1 */
- /***************************/
outb(0x2,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
else {
dev_warn(dev->hw_dev,
"Error in selection of interrupt enable or disable\n");
return -EINVAL;
} /* elseif(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
} /* if ((data[3]>= 0) && (data[3] <= 65535)) */
else {
dev_warn(dev->hw_dev,
"Error in selection of reload value\n");
return -EINVAL;
} /* else if ((data[3]>= 0) && (data[3] <= 65535)) */
i_TimerCounterWatchdogInterrupt = data[7];
i_TimerCounter1Init = 1;
break;
case COUNTER2: /* selecting counter or timer */
@@ -1545,157 +1369,125 @@ static int i_APCI1500_ConfigCounterTimerWatchdog(struct comedi_device *dev,
"This choice for software or hardware trigger does not exist\n");
return -EINVAL;
} /* switch(data[5]) */
/* Selecting software or hardware gate */
switch (data[6]) {
case 0:
data[6] = APCI1500_SOFTWARE_GATE;
break;
case 1:
data[6] = APCI1500_HARDWARE_GATE;
break;
default:
dev_warn(dev->hw_dev,
"This choice for software or hardware gate does not exist\n");
return -EINVAL;
} /* switch(data[6]) */
i_TimerCounterMode = data[2] | data[4] | data[5] | data[6] | 7;
- /*************************/
/* Test the reload value */
- /*************************/
if ((data[3] >= 0) && (data[3] <= 65535)) {
if (data[7] == APCI1500_ENABLE
|| data[7] == APCI1500_DISABLE) {
- /************************************************/
/* Selects the mode register of timer/counter 2 */
- /************************************************/
outb(APCI1500_RW_CPT_TMR2_MODE_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************/
/* Writes the new mode */
- /***********************/
outb(i_TimerCounterMode,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of timer/counter 2 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR2_TIME_CST_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************/
/* Writes the low value */
- /*************************/
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of timer/counter 2 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR2_TIME_CST_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**************************/
/* Writes the high value */
- /**************************/
data[3] = data[3] >> 8;
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************/
/* Reads the register */
- /**********************/
i_MasterConfiguration =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************************************/
/* Enables timer/counter 2 and triggers timer/counter 2 */
- /********************************************************/
i_MasterConfiguration =
i_MasterConfiguration | 0x20;
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************/
/* Writes the new configuration */
- /********************************/
outb(i_MasterConfiguration,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************/
/* Selects the commands register of */
/* timer/counter 2 */
- /****************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************/
/* Disable timer/counter 2 */
- /***************************/
outb(0x0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************/
/* Selects the commands register of */
/* timer/counter 2 */
- /****************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************/
/* Trigger timer/counter 1 */
- /***************************/
outb(0x2,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
else {
dev_warn(dev->hw_dev,
"Error in selection of interrupt enable or disable\n");
return -EINVAL;
} /* elseif(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
} /* if ((data[3]>= 0) && (data[3] <= 65535)) */
else {
dev_warn(dev->hw_dev,
"Error in selection of reload value\n");
return -EINVAL;
} /* else if ((data[3]>= 0) && (data[3] <= 65535)) */
i_TimerCounterWatchdogInterrupt = data[7];
i_TimerCounter2Init = 1;
break;
case COUNTER3: /* selecting counter or watchdog */
@@ -1723,176 +1515,138 @@ static int i_APCI1500_ConfigCounterTimerWatchdog(struct comedi_device *dev,
default:
dev_warn(dev->hw_dev,
"This option for single/continuous mode does not exist\n");
return -EINVAL;
} /* switch(data[4]) */
/* Selecting software or hardware gate */
switch (data[6]) {
case 0:
data[6] = APCI1500_SOFTWARE_GATE;
break;
case 1:
data[6] = APCI1500_HARDWARE_GATE;
break;
default:
dev_warn(dev->hw_dev,
"This choice for software or hardware gate does not exist\n");
return -EINVAL;
} /* switch(data[6]) */
- /*****************************/
/* Test if used for watchdog */
- /*****************************/
if (data[2] == APCI1500_WATCHDOG) {
- /*****************************/
/* - Enables the output line */
/* - Enables retrigger */
/* - Pulses output */
- /*****************************/
i_TimerCounterMode = data[2] | data[4] | 0x54;
} /* if (data[2] == APCI1500_WATCHDOG) */
else {
i_TimerCounterMode = data[2] | data[4] | data[6] | 7;
} /* elseif (data[2] == APCI1500_WATCHDOG) */
- /*************************/
/* Test the reload value */
- /*************************/
if ((data[3] >= 0) && (data[3] <= 65535)) {
if (data[7] == APCI1500_ENABLE
|| data[7] == APCI1500_DISABLE) {
- /************************************************/
/* Selects the mode register of watchdog/counter 3 */
- /************************************************/
outb(APCI1500_RW_CPT_TMR3_MODE_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************/
/* Writes the new mode */
- /***********************/
outb(i_TimerCounterMode,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of watchdog/counter 3 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR3_TIME_CST_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************/
/* Writes the low value */
- /*************************/
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************************************************/
/* Selects the constant register of watchdog/counter 3 */
- /****************************************************/
outb(APCI1500_RW_CPT_TMR3_TIME_CST_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**************************/
/* Writes the high value */
- /**************************/
data[3] = data[3] >> 8;
outb(data[3],
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /**********************/
/* Reads the register */
- /**********************/
i_MasterConfiguration =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************************************/
/* Enables watchdog/counter 3 and triggers watchdog/counter 3 */
- /********************************************************/
i_MasterConfiguration =
i_MasterConfiguration | 0x10;
- /*********************************************/
/* Selects the master configuration register */
- /*********************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************************/
/* Writes the new configuration */
- /********************************/
outb(i_MasterConfiguration,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /********************/
/* Test if COUNTER */
- /********************/
if (data[2] == APCI1500_COUNTER) {
- /*************************************/
/* Selects the command register of */
/* watchdog/counter 3 */
- /*************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************************/
/* Disable the watchdog/counter 3 and starts it */
- /*************************************************/
outb(0x0,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************/
/* Selects the command register of */
/* watchdog/counter 3 */
- /*************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************************/
/* Trigger the watchdog/counter 3 and starts it */
- /*************************************************/
outb(0x2,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* elseif(data[2]==APCI1500_COUNTER) */
} /* if(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
else {
dev_warn(dev->hw_dev,
"Error in selection of interrupt enable or disable\n");
return -EINVAL;
} /* elseif(data[7]== APCI1500_ENABLE ||data[7]== APCI1500_DISABLE) */
} /* if ((data[3]>= 0) && (data[3] <= 65535)) */
else {
dev_warn(dev->hw_dev,
"Error in selection of reload value\n");
return -EINVAL;
} /* else if ((data[3]>= 0) && (data[3] <= 65535)) */
i_TimerCounterWatchdogInterrupt = data[7];
i_WatchdogCounter3Init = 1;
@@ -1936,300 +1690,256 @@ static int i_APCI1500_ConfigCounterTimerWatchdog(struct comedi_device *dev,
+----------------------------------------------------------------------------+
*/
static int i_apci1500_timer_watchdog(struct comedi_device *dev,
struct comedi_subdevice *s, struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
int i_CommandAndStatusValue;
switch (data[0]) {
case COUNTER1:
switch (data[1]) {
case START:
if (i_TimerCounter1Init == 1) {
if (i_TimerCounterWatchdogInterrupt == 1) {
i_CommandAndStatusValue = 0xC4; /* Enable the interrupt */
} /* if(i_TimerCounterWatchdogInterrupt==1) */
else {
i_CommandAndStatusValue = 0xE4; /* disable the interrupt */
} /* elseif(i_TimerCounterWatchdogInterrupt==1) */
- /**************************/
/* Starts timer/counter 1 */
- /**************************/
i_TimerCounter1Enabled = 1;
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter1Init==1) */
else {
dev_warn(dev->hw_dev,
"Counter/Timer1 not configured\n");
return -EINVAL;
}
break;
case STOP:
- /**************************/
/* Stop timer/counter 1 */
- /**************************/
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(0x00,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_TimerCounter1Enabled = 0;
break;
case TRIGGER:
if (i_TimerCounter1Init == 1) {
if (i_TimerCounter1Enabled == 1) {
- /************************/
/* Set Trigger and gate */
- /************************/
i_CommandAndStatusValue = 0x6;
} /* if( i_TimerCounter1Enabled==1) */
else {
- /***************/
/* Set Trigger */
- /***************/
i_CommandAndStatusValue = 0x2;
} /* elseif(i_TimerCounter1Enabled==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter1Init==1) */
else {
dev_warn(dev->hw_dev,
"Counter/Timer1 not configured\n");
return -EINVAL;
}
break;
default:
dev_warn(dev->hw_dev,
"The specified option for start/stop/trigger does not exist\n");
return -EINVAL;
} /* switch(data[1]) */
break;
case COUNTER2:
switch (data[1]) {
case START:
if (i_TimerCounter2Init == 1) {
if (i_TimerCounterWatchdogInterrupt == 1) {
i_CommandAndStatusValue = 0xC4; /* Enable the interrupt */
} /* if(i_TimerCounterWatchdogInterrupt==1) */
else {
i_CommandAndStatusValue = 0xE4; /* disable the interrupt */
} /* elseif(i_TimerCounterWatchdogInterrupt==1) */
- /**************************/
/* Starts timer/counter 2 */
- /**************************/
i_TimerCounter2Enabled = 1;
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter2Init==1) */
else {
dev_warn(dev->hw_dev,
"Counter/Timer2 not configured\n");
return -EINVAL;
}
break;
case STOP:
- /**************************/
/* Stop timer/counter 2 */
- /**************************/
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(0x00,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_TimerCounter2Enabled = 0;
break;
case TRIGGER:
if (i_TimerCounter2Init == 1) {
if (i_TimerCounter2Enabled == 1) {
- /************************/
/* Set Trigger and gate */
- /************************/
i_CommandAndStatusValue = 0x6;
} /* if( i_TimerCounter2Enabled==1) */
else {
- /***************/
/* Set Trigger */
- /***************/
i_CommandAndStatusValue = 0x2;
} /* elseif(i_TimerCounter2Enabled==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter2Init==1) */
else {
dev_warn(dev->hw_dev,
"Counter/Timer2 not configured\n");
return -EINVAL;
}
break;
default:
dev_warn(dev->hw_dev,
"The specified option for start/stop/trigger does not exist\n");
return -EINVAL;
} /* switch(data[1]) */
break;
case COUNTER3:
switch (data[1]) {
case START:
if (i_WatchdogCounter3Init == 1) {
if (i_TimerCounterWatchdogInterrupt == 1) {
i_CommandAndStatusValue = 0xC4; /* Enable the interrupt */
} /* if(i_TimerCounterWatchdogInterrupt==1) */
else {
i_CommandAndStatusValue = 0xE4; /* disable the interrupt */
} /* elseif(i_TimerCounterWatchdogInterrupt==1) */
- /**************************/
/* Starts Watchdog/counter 3 */
- /**************************/
i_WatchdogCounter3Enabled = 1;
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_WatchdogCounter3init==1) */
else {
dev_warn(dev->hw_dev,
"Watchdog/Counter3 not configured\n");
return -EINVAL;
}
break;
case STOP:
- /**************************/
/* Stop Watchdog/counter 3 */
- /**************************/
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(0x00,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_WatchdogCounter3Enabled = 0;
break;
case TRIGGER:
switch (data[2]) {
case 0: /* triggering counter 3 */
if (i_WatchdogCounter3Init == 1) {
if (i_WatchdogCounter3Enabled == 1) {
- /************************/
/* Set Trigger and gate */
- /************************/
i_CommandAndStatusValue = 0x6;
} /* if( i_WatchdogCounter3Enabled==1) */
else {
- /***************/
/* Set Trigger */
- /***************/
i_CommandAndStatusValue = 0x2;
} /* elseif(i_WatchdogCounter3Enabled==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_WatchdogCounter3Init==1) */
else {
dev_warn(dev->hw_dev,
"Counter3 not configured\n");
return -EINVAL;
}
break;
case 1:
/* triggering Watchdog 3 */
if (i_WatchdogCounter3Init == 1) {
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(0x6,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_WatchdogCounter3Init==1) */
else {
dev_warn(dev->hw_dev,
"Watchdog 3 not configured\n");
return -EINVAL;
}
break;
default:
dev_warn(dev->hw_dev,
"Wrong choice of watchdog/counter3\n");
return -EINVAL;
} /* switch(data[2]) */
break;
default:
@@ -2266,171 +1976,147 @@ static int i_apci1500_timer_watchdog(struct comedi_device *dev,
| Output Parameters : -- |
+----------------------------------------------------------------------------+
| Return Value : TRUE : No error occur |
| : FALSE : Error occur. Return the error |
| |
+----------------------------------------------------------------------------+
*/
static int i_APCI1500_ReadCounterTimerWatchdog(struct comedi_device *dev,
struct comedi_subdevice *s,
struct comedi_insn *insn,
unsigned int *data)
{
struct addi_private *devpriv = dev->private;
int i_CommandAndStatusValue;
switch (data[0]) {
case COUNTER1:
/* Read counter/timer1 */
if (i_TimerCounter1Init == 1) {
if (i_TimerCounter1Enabled == 1) {
- /************************/
/* Set RCC and gate */
- /************************/
i_CommandAndStatusValue = 0xC;
} /* if( i_TimerCounter1Init==1) */
else {
- /***************/
/* Set RCC */
- /***************/
i_CommandAndStatusValue = 0x8;
} /* elseif(i_TimerCounter1Init==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************/
/* Selects the counter register (high) */
- /***************************************/
outb(APCI1500_R_CPT_TMR1_VALUE_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] = data[0] << 8;
data[0] = data[0] & 0xff00;
outb(APCI1500_R_CPT_TMR1_VALUE_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
data[0] | inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter1Init==1) */
else {
dev_warn(dev->hw_dev,
"Timer/Counter1 not configured\n");
return -EINVAL;
} /* elseif( i_TimerCounter1Init==1) */
break;
case COUNTER2:
/* Read counter/timer2 */
if (i_TimerCounter2Init == 1) {
if (i_TimerCounter2Enabled == 1) {
- /************************/
/* Set RCC and gate */
- /************************/
i_CommandAndStatusValue = 0xC;
} /* if( i_TimerCounter2Init==1) */
else {
- /***************/
/* Set RCC */
- /***************/
i_CommandAndStatusValue = 0x8;
} /* elseif(i_TimerCounter2Init==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************/
/* Selects the counter register (high) */
- /***************************************/
outb(APCI1500_R_CPT_TMR2_VALUE_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] = data[0] << 8;
data[0] = data[0] & 0xff00;
outb(APCI1500_R_CPT_TMR2_VALUE_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
data[0] | inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_TimerCounter2Init==1) */
else {
dev_warn(dev->hw_dev,
"Timer/Counter2 not configured\n");
return -EINVAL;
} /* elseif( i_TimerCounter2Init==1) */
break;
case COUNTER3:
/* Read counter/watchdog2 */
if (i_WatchdogCounter3Init == 1) {
if (i_WatchdogCounter3Enabled == 1) {
- /************************/
/* Set RCC and gate */
- /************************/
i_CommandAndStatusValue = 0xC;
} /* if( i_TimerCounter2Init==1) */
else {
- /***************/
/* Set RCC */
- /***************/
i_CommandAndStatusValue = 0x8;
} /* elseif(i_WatchdogCounter3Init==1) */
- /********************************************/
/* Selects the commands and status register */
- /********************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
outb(i_CommandAndStatusValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************/
/* Selects the counter register (high) */
- /***************************************/
outb(APCI1500_R_CPT_TMR3_VALUE_HIGH,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] = data[0] << 8;
data[0] = data[0] & 0xff00;
outb(APCI1500_R_CPT_TMR3_VALUE_LOW,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
data[0] =
data[0] | inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
} /* if( i_WatchdogCounter3Init==1) */
else {
dev_warn(dev->hw_dev,
"WatchdogCounter3 not configured\n");
return -EINVAL;
} /* elseif( i_WatchdogCounter3Init==1) */
@@ -2508,416 +2194,322 @@ static int i_APCI1500_ConfigureInterrupt(struct comedi_device *dev,
unsigned int ui_Status;
int i_RegValue;
int i_Constant;
devpriv->tsk_Current = current;
outl(0x0, devpriv->i_IobaseAmcc + 0x38);
if (data[0] == 1) {
i_Constant = 0xC0;
} /* if(data[0]==1) */
else {
if (data[0] == 0) {
i_Constant = 0x00;
} /* if{data[0]==0) */
else {
dev_warn(dev->hw_dev,
"The parameter passed to driver is in error for enabling the voltage interrupt\n");
return -EINVAL;
} /* else if(data[0]==0) */
} /* elseif(data[0]==1) */
- /*****************************************************/
/* Selects the mode specification register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*********************************************/
/* Writes the new configuration (APCI1500_OR) */
- /*********************************************/
i_RegValue = (i_RegValue & 0xF9) | APCI1500_OR;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************/
/* Authorises the interrupt on the board */
- /*****************************************/
outb(0xC0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the pattern polarity register of port B */
- /***************************************************/
outb(APCI1500_RW_PORT_B_PATTERN_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(i_Constant, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the pattern transition register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_PATTERN_TRANSITION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(i_Constant, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************************/
/* Selects the pattern mask register of port B */
- /***********************************************/
outb(APCI1500_RW_PORT_B_PATTERN_MASK,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(i_Constant, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of port A */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of port B */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of timer 1 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 1 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of timer 2 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 2 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of timer 3 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 3 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Authorizes the main interrupt on the board */
- /**********************************************/
outb(0xD0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /***************************/
/* Enables the PCI interrupt */
- /*****************************/
outl(0x3000, devpriv->i_IobaseAmcc + 0x38);
ui_Status = inl(devpriv->i_IobaseAmcc + 0x10);
ui_Status = inl(devpriv->i_IobaseAmcc + 0x38);
outl(0x23000, devpriv->i_IobaseAmcc + 0x38);
return insn->n;
}
/*
+----------------------------------------------------------------------------+
| Function Name : static void v_APCI1500_Interrupt |
| (int irq , void *d) |
+----------------------------------------------------------------------------+
| Task : Interrupt handler |
+----------------------------------------------------------------------------+
| Input Parameters : int irq : irq number |
| void *d : void pointer |
+----------------------------------------------------------------------------+
| Output Parameters : -- |
+----------------------------------------------------------------------------+
| Return Value : TRUE : No error occur |
| : FALSE : Error occur. Return the error |
| |
+----------------------------------------------------------------------------+
*/
static void v_APCI1500_Interrupt(int irq, void *d)
{
struct comedi_device *dev = d;
struct addi_private *devpriv = dev->private;
unsigned int ui_InterruptStatus = 0;
int i_RegValue = 0;
i_InterruptMask = 0;
- /***********************************/
/* Read the board interrupt status */
- /***********************************/
ui_InterruptStatus = inl(devpriv->i_IobaseAmcc + 0x38);
- /***************************************/
/* Test if board generated a interrupt */
- /***************************************/
if ((ui_InterruptStatus & 0x800000) == 0x800000) {
- /************************/
/* Disable all Interrupt */
- /************************/
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
/* outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,devpriv->iobase+APCI1500_Z8536_CONTROL_REGISTER); */
- /**********************************************/
/* Disables the main interrupt on the board */
- /**********************************************/
/* outb(0x00,devpriv->iobase+APCI1500_Z8536_CONTROL_REGISTER); */
- /*****************************************************/
/* Selects the command and status register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if ((i_RegValue & 0x60) == 0x60) {
- /*****************************************************/
/* Selects the command and status register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of port A */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_InterruptMask = i_InterruptMask | 1;
if (i_Logic == APCI1500_OR_PRIORITY) {
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***************************************************/
/* Selects the interrupt vector register of port A */
- /***************************************************/
outb(APCI1500_RW_PORT_A_INTERRUPT_CONTROL,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_InputChannel = 1 + (i_RegValue >> 1);
} /* if(i_Logic==APCI1500_OR_PRIORITY) */
else {
i_InputChannel = 0;
} /* elseif(i_Logic==APCI1500_OR_PRIORITY) */
} /* if ((i_RegValue & 0x60) == 0x60) */
- /*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if ((i_RegValue & 0x60) == 0x60) {
- /*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of port B */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /****************/
/* Reads port B */
- /****************/
i_RegValue =
inb((unsigned int) devpriv->iobase +
APCI1500_Z8536_PORT_B);
i_RegValue = i_RegValue & 0xC0;
- /**************************************/
/* Tests if this is an external error */
- /**************************************/
if (i_RegValue) {
/* Disable the interrupt */
- /*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outl(0x0, devpriv->i_IobaseAmcc + 0x38);
if (i_RegValue & 0x80) {
i_InterruptMask =
i_InterruptMask | 0x40;
} /* if (i_RegValue & 0x80) */
if (i_RegValue & 0x40) {
i_InterruptMask =
i_InterruptMask | 0x80;
} /* if (i_RegValue & 0x40) */
} /* if (i_RegValue) */
else {
i_InterruptMask = i_InterruptMask | 2;
} /* if (i_RegValue) */
} /* if ((i_RegValue & 0x60) == 0x60) */
- /*****************************************************/
/* Selects the command and status register of timer 1 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if ((i_RegValue & 0x60) == 0x60) {
- /*****************************************************/
/* Selects the command and status register of timer 1 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 1 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_InterruptMask = i_InterruptMask | 4;
} /* if ((i_RegValue & 0x60) == 0x60) */
- /*****************************************************/
/* Selects the command and status register of timer 2 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if ((i_RegValue & 0x60) == 0x60) {
- /*****************************************************/
/* Selects the command and status register of timer 2 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 2 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
i_InterruptMask = i_InterruptMask | 8;
} /* if ((i_RegValue & 0x60) == 0x60) */
- /*****************************************************/
/* Selects the command and status register of timer 3 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_RegValue =
inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
if ((i_RegValue & 0x60) == 0x60) {
- /*****************************************************/
/* Selects the command and status register of timer 3 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
- /***********************************/
/* Deletes the interrupt of timer 3 */
- /***********************************/
i_RegValue = (i_RegValue & 0x0F) | 0x20;
outb(i_RegValue,
devpriv->iobase +
APCI1500_Z8536_CONTROL_REGISTER);
if (i_CounterLogic == APCI1500_COUNTER) {
i_InterruptMask = i_InterruptMask | 0x10;
} /* if(i_CounterLogic==APCI1500_COUNTER) */
else {
i_InterruptMask = i_InterruptMask | 0x20;
}
} /* if ((i_RegValue & 0x60) == 0x60) */
send_sig(SIGIO, devpriv->tsk_Current, 0); /* send signal to the sample */
- /***********************/
/* Enable all Interrupts */
- /***********************/
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /**********************************************/
/* Authorizes the main interrupt on the board */
- /**********************************************/
outb(0xD0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
} /* if ((ui_InterruptStatus & 0x800000) == 0x800000) */
else {
dev_warn(dev->hw_dev,
"Interrupt from unknown source\n");
} /* else if ((ui_InterruptStatus & 0x800000) == 0x800000) */
return;
}
/*
+----------------------------------------------------------------------------+
| Function Name : int i_APCI1500_Reset(struct comedi_device *dev) | |
+----------------------------------------------------------------------------+
| Task :resets all the registers |
+----------------------------------------------------------------------------+
| Input Parameters : struct comedi_device *dev
+----------------------------------------------------------------------------+
| Output Parameters : -- |
+----------------------------------------------------------------------------+
@@ -2927,224 +2519,180 @@ static void v_APCI1500_Interrupt(int irq, void *d)
*/
static int i_APCI1500_Reset(struct comedi_device *dev)
{
struct addi_private *devpriv = dev->private;
int i_DummyRead = 0;
i_TimerCounter1Init = 0;
i_TimerCounter2Init = 0;
i_WatchdogCounter3Init = 0;
i_Event1Status = 0;
i_Event2Status = 0;
i_TimerCounterWatchdogInterrupt = 0;
i_Logic = 0;
i_CounterLogic = 0;
i_InterruptMask = 0;
i_InputChannel = 0;
i_TimerCounter1Enabled = 0;
i_TimerCounter2Enabled = 0;
i_WatchdogCounter3Enabled = 0;
- /******************/
/* Software reset */
- /******************/
i_DummyRead = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
i_DummyRead = inb(devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(1, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the master configuration control register */
- /*****************************************************/
outb(APCI1500_RW_MASTER_CONFIGURATION_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0xF4, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the mode specification register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0x10, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data path polarity register of port A */
outb(APCI1500_RW_PORT_A_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* High level of port A means 1 */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port A */
outb(APCI1500_RW_PORT_A_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port A */
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port A */
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of port A: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the handshake specification register of port A */
outb(APCI1500_RW_PORT_A_HANDSHAKE_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes the register */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the mode specification register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
outb(0x10, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data path polarity register of port B */
outb(APCI1500_RW_PORT_B_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* A high level of port B means 1 */
outb(0x7F, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port B */
outb(APCI1500_RW_PORT_B_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs */
outb(0xFF, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port B */
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of port B */
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of port B: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the handshake specification register of port B */
outb(APCI1500_RW_PORT_B_HANDSHAKE_SPECIFICATION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes the register */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the data path polarity register of port C */
- /*****************************************************/
outb(APCI1500_RW_PORT_C_DATA_PCITCH_POLARITY,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* High level of port C means 1 */
outb(0x9, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the data direction register of port C */
outb(APCI1500_RW_PORT_C_DATA_DIRECTION,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* All bits used as inputs except channel 1 */
outb(0x0E, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the special IO register of port C */
outb(APCI1500_RW_PORT_C_SPECIAL_IO_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes it */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 1 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of timer 1 */
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates the interrupt management of timer 1 */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 2 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of timer 2 */
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates Timer 2 interrupt management: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /******************************************************/
/* Selects the command and status register of timer 3 */
- /******************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes IP and IUS */
outb(0x20, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Selects the command and status register of Timer 3 */
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deactivates interrupt management of timer 3: */
outb(0xE0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* Deletes all interrupts */
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
/* reset all the digital outputs */
outw(0x0, devpriv->i_IobaseAddon + APCI1500_DIGITAL_OP);
-/*******************************/
/* Disable the board interrupt */
-/*******************************/
- /*************************************************/
/* Selects the master interrupt control register */
- /*************************************************/
outb(APCI1500_RW_MASTER_INTERRUPT_CONTROL,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
- /*****************************************************/
/* Selects the command and status register of port A */
- /*****************************************************/
outb(APCI1500_RW_PORT_A_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/*****************************************************/
/* Selects the command and status register of port B */
- /*****************************************************/
outb(APCI1500_RW_PORT_B_COMMAND_AND_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/*****************************************************/
/* Selects the command and status register of timer 1 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR1_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/*****************************************************/
/* Selects the command and status register of timer 2 */
- /*****************************************************/
outb(APCI1500_RW_CPT_TMR2_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/*****************************************************/
/* Selects the command and status register of timer 3*/
-/*****************************************************/
outb(APCI1500_RW_CPT_TMR3_CMD_STATUS,
devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
-/****************************/
/* Deactivates all interrupts */
-/******************************/
outb(0x00, devpriv->iobase + APCI1500_Z8536_CONTROL_REGISTER);
return 0;
}
--
1.8.5.3
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
