[PATCH RFC 17/17 v2] staging: dgap: Rename driver and include files to dgap.c and dgap.h

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Rename driver and include files to dgap.c and dgap.h to better fit kernel naming conventions.

Signed-off-by: Mark Hounschell <markh@xxxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>

 drivers/staging/dgap/Makefile      |    2 
 drivers/staging/dgap/dgap.c        | 8606 +++++++++++++++++++++++++++
 drivers/staging/dgap/dgap.h        | 1566 ++++
 drivers/staging/dgap/dgap_driver.c | 8606 ---------------------------
 drivers/staging/dgap/dgap_driver.h | 1566 ----
 5 files changed, 10172 insertions(+), 10174 deletions(-)

diff -urpN linux-3.13.1-orig/drivers/staging/dgap/dgap.c linux-3.13.1-new/drivers/staging/dgap/dgap.c
--- linux-3.13.1-orig/drivers/staging/dgap/dgap.c	1969-12-31 19:00:00.000000000 -0500
+++ linux-3.13.1-new/drivers/staging/dgap/dgap.c	2014-02-11 10:26:22.649123876 -0500
@@ -0,0 +1,8606 @@
+/*
+ * Copyright 2003 Digi International (www.digi.com)
+ *	Scott H Kilau <Scott_Kilau at digi dot com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ * 
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the 
+ * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR 
+ * PURPOSE.  See the GNU General Public License for more details.
+ * 
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+/*
+ *      In the original out of kernel Digi dgap driver, firmware
+ *      loading was done via user land to driver handshaking.
+ *
+ *      For cards that support a concentrator (port expander),
+ *      I believe the concentrator its self told the card which
+ *      concentrator is actually attached and then that info
+ *      was used to tell user land which concentrator firmware
+ *      image was to be downloaded. I think even the BIOS or
+ *      FEP images required would change with the connection
+ *      of a particular concentrator. 
+ *
+ *      Since I have no access to any of these cards or
+ *      concentrators, I cannot put the correct concentrator
+ *      firmware file names into the firmware_info structure
+ *      as is now done for the BIOS and FEP images. 
+ *
+ *      I think, but am not certain, that the cards supporting
+ *      concentrators will function without them. So support
+ *      of these cards has been left in this driver.
+ *
+ *      In order to fully support those cards, they would
+ *      either have to be acquired for dissection or maybe
+ *      Digi International could provide some assistance.
+ */
+#undef DIGI_CONCENTRATORS_SUPPORTED
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>	/* For udelay */
+#include <linux/slab.h>
+#include <asm/uaccess.h>	/* For copy_from_user/copy_to_user */
+#include <linux/sched.h>
+#include <linux/firmware.h>
+
+#include <linux/version.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>     /* For tty_schedule_flip */
+#include <linux/ctype.h>
+
+#include <linux/interrupt.h>    /* For tasklet and interrupt structs/defines */
+#include <linux/serial_reg.h>
+#include <asm/uaccess.h>        /* For copy_from_user/copy_to_user */
+#include <asm/io.h>             /* For read[bwl]/write[bwl] */
+
+#include <linux/string.h>
+#include <linux/device.h>
+#include <linux/kdev_t.h>
+
+#include "dgap.h"
+
+/*
+ * Function prototypes.
+ */
+static int dgap_gettok(char **in, struct cnode *p);
+static char *dgap_getword(char **in);
+static char *dgap_savestring(char *s);
+static struct cnode *dgap_newnode(int t);
+static int dgap_checknode(struct cnode *p);
+static void dgap_err(char *s);
+
+/*
+ * Our needed internal static variables...
+ */
+static struct cnode dgap_head;
+#define MAXCWORD 200
+static char dgap_cword[MAXCWORD];
+
+#define init_MUTEX(sem)         sema_init(sem, 1)
+#define DECLARE_MUTEX(name)     \
+        struct semaphore name = __SEMAPHORE_INITIALIZER(name, 1)
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Digi International, http://www.digi.com";);
+MODULE_DESCRIPTION("Driver for the Digi International EPCA PCI based product line");
+MODULE_SUPPORTED_DEVICE("dgap");
+
+/*
+ * insmod command line overrideable parameters
+ *
+ * NOTE: we use a set of macros to create the variables, which allows
+ * us to specify the variable type, name, initial value, and description.
+ */
+PARM_INT(debug,		0x00,		0644,	"Driver debugging level");
+PARM_INT(rawreadok,	1,		0644,	"Bypass flip buffers on input");
+
+/**************************************************************************
+ *
+ * protos for this file
+ *
+ */
+
+static int		dgap_start(void);
+static void		dgap_init_globals(void);
+static int		dgap_found_board(struct pci_dev *pdev, int id);
+static void		dgap_cleanup_board(struct board_t *brd);
+static void		dgap_poll_handler(ulong dummy);
+static int		dgap_init_pci(void);
+static int		dgap_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void		dgap_remove_one(struct pci_dev *dev);
+static int		dgap_probe1(struct pci_dev *pdev, int card_type);
+static void		dgap_mbuf(struct board_t *brd, const char *fmt, ...);
+static int		dgap_do_remap(struct board_t *brd);
+static irqreturn_t	dgap_intr(int irq, void *voidbrd);
+static void 		dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds);
+static int 		dgap_event(struct board_t *bd);
+static int 		dgap_firmware_load(struct pci_dev *pdev, int card_type);
+static void 		dgap_do_bios_load(struct board_t *brd, uchar *ubios, int len);
+static void 		dgap_do_fep_load(struct board_t *brd, uchar *ufep, int len);
+static void 		dgap_sysfs_create(struct board_t *brd);
+static void 		dgap_get_vpd(struct board_t *brd);
+static void 		dgap_do_reset_board(struct board_t *brd);
+static void 		dgap_do_wait_for_bios(struct board_t *brd);
+static void 		dgap_do_wait_for_fep(struct board_t *brd);
+static int 		dgap_after_config_loaded(int brd);
+static int 		dgap_finalize_board_init(struct board_t *brd);
+static void 		dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds);
+static int 		dgap_event(struct board_t *bd);
+
+/*****************************************************************************
+ * Function prototypes from dgap_tty.c
+ *****************************************************************************/
+static int dgap_tty_open(struct tty_struct *tty, struct file *file);
+static void dgap_tty_close(struct tty_struct *tty, struct file *file);
+static int dgap_block_til_ready(struct tty_struct *tty, struct file *file, struct channel_t *ch);
+static int dgap_tty_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
+static int dgap_tty_digigeta(struct tty_struct *tty, struct digi_t __user *retinfo);
+static int dgap_tty_digiseta(struct tty_struct *tty, struct digi_t __user *new_info);
+static int dgap_tty_digigetedelay(struct tty_struct *tty, int __user *retinfo);
+static int dgap_tty_digisetedelay(struct tty_struct *tty, int __user *new_info);
+static int dgap_tty_write_room(struct tty_struct* tty);
+static int dgap_tty_chars_in_buffer(struct tty_struct* tty);
+static void dgap_tty_start(struct tty_struct *tty);
+static void dgap_tty_stop(struct tty_struct *tty);
+static void dgap_tty_throttle(struct tty_struct *tty);
+static void dgap_tty_unthrottle(struct tty_struct *tty);
+static void dgap_tty_flush_chars(struct tty_struct *tty);
+static void dgap_tty_flush_buffer(struct tty_struct *tty);
+static void dgap_tty_hangup(struct tty_struct *tty);
+static int dgap_wait_for_drain(struct tty_struct *tty);
+static int dgap_set_modem_info(struct tty_struct *tty, unsigned int command, unsigned int __user *value);
+static int dgap_get_modem_info(struct channel_t *ch, unsigned int __user *value);
+static int dgap_tty_digisetcustombaud(struct tty_struct *tty, int __user *new_info);
+static int dgap_tty_digigetcustombaud(struct tty_struct *tty, int __user *retinfo);
+static int dgap_tty_tiocmget(struct tty_struct *tty);
+static int dgap_tty_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear);
+static int dgap_tty_send_break(struct tty_struct *tty, int msec);
+static void dgap_tty_wait_until_sent(struct tty_struct *tty, int timeout);
+static int dgap_tty_write(struct tty_struct *tty, const unsigned char *buf, int count);
+static void dgap_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios);
+static int dgap_tty_put_char(struct tty_struct *tty, unsigned char c);
+static void dgap_tty_send_xchar(struct tty_struct *tty, char ch);
+
+static const struct tty_operations dgap_tty_ops = {
+	.open = dgap_tty_open,
+	.close = dgap_tty_close,
+	.write = dgap_tty_write,
+	.write_room = dgap_tty_write_room,
+	.flush_buffer = dgap_tty_flush_buffer,
+	.chars_in_buffer = dgap_tty_chars_in_buffer,
+	.flush_chars = dgap_tty_flush_chars,
+	.ioctl = dgap_tty_ioctl,
+	.set_termios = dgap_tty_set_termios,
+	.stop = dgap_tty_stop, 
+	.start = dgap_tty_start,
+	.throttle = dgap_tty_throttle,
+	.unthrottle = dgap_tty_unthrottle,
+	.hangup = dgap_tty_hangup,
+	.put_char = dgap_tty_put_char,
+	.tiocmget = dgap_tty_tiocmget,
+	.tiocmset = dgap_tty_tiocmset,
+	.break_ctl = dgap_tty_send_break,
+	.wait_until_sent = dgap_tty_wait_until_sent,
+	.send_xchar = dgap_tty_send_xchar
+};
+
+/*****************************************************************************
+ * Function prototypes from dgap_sysfs.h
+ *****************************************************************************/
+static void dgap_create_ports_sysfiles(struct board_t *bd);
+static void dgap_remove_ports_sysfiles(struct board_t *bd);
+static void dgap_create_driver_sysfiles(struct pci_driver *);
+static void dgap_remove_driver_sysfiles(struct pci_driver *);
+static void dgap_create_tty_sysfs(struct un_t *un, struct device *c);
+static void dgap_remove_tty_sysfs(struct device *c);
+
+#ifdef DIGI_CONCENTRATORS_SUPPORTED
+static void             dgap_do_conc_load(struct board_t *brd, uchar *uaddr, int len);
+#endif
+
+/* Driver load/unload functions */
+int			dgap_init_module(void);
+void			dgap_cleanup_module(void);
+
+module_init(dgap_init_module);
+module_exit(dgap_cleanup_module);
+
+/*
+ * File operations permitted on Control/Management major.
+ */
+static struct file_operations DgapBoardFops =
+{
+	.owner		=	THIS_MODULE,
+};
+
+/*
+ * Globals
+ */
+uint			dgap_NumBoards;
+struct board_t		*dgap_Board[MAXBOARDS];
+DEFINE_SPINLOCK(dgap_global_lock);
+ulong			dgap_poll_counter;
+char			*dgap_config_buf;
+int			dgap_driver_state = DRIVER_INITIALIZED;
+DEFINE_SPINLOCK(dgap_dl_lock);
+wait_queue_head_t	dgap_dl_wait;
+int			dgap_dl_action;
+int			dgap_poll_tick = 20;	/* Poll interval - 20 ms */
+
+/*
+ * Static vars.
+ */
+static int		dgap_Major_Control_Registered = FALSE;
+static uint		dgap_driver_start = FALSE;
+static uint 		dgap_count = 500;
+static struct class *	dgap_class;
+
+/*
+ * Poller stuff
+ */
+static 			DEFINE_SPINLOCK(dgap_poll_lock);	/* Poll scheduling lock */
+static ulong		dgap_poll_time;				/* Time of next poll */
+static uint		dgap_poll_stop;				/* Used to tell poller to stop */
+static struct timer_list dgap_poll_timer;
+
+/*
+     SUPPORTED PRODUCTS
+
+     Card Model               Number of Ports      Interface
+     ----------------------------------------------------------------
+     Acceleport Xem           4 - 64              (EIA232 & EIA422)
+     Acceleport Xr            4 & 8               (EIA232)
+     Acceleport Xr 920        4 & 8               (EIA232)
+     Acceleport C/X           8 - 128             (EIA232)
+     Acceleport EPC/X         8 - 224             (EIA232)
+     Acceleport Xr/422        4 & 8               (EIA422)
+     Acceleport 2r/920        2                   (EIA232)
+     Acceleport 4r/920        4                   (EIA232)
+     Acceleport 8r/920        8                   (EIA232)
+
+     IBM 8-Port Asynchronous PCI Adapter          (EIA232)
+     IBM 128-Port Asynchronous PCI Adapter        (EIA232 & EIA422)
+*/
+
+static struct pci_device_id dgap_pci_tbl[] = {
+	{       DIGI_VID, PCI_DEVICE_XEM_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	0 },
+	{       DIGI_VID, PCI_DEVICE_CX_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,   1 },
+	{       DIGI_VID, PCI_DEVICE_CX_IBM_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	2 },
+	{       DIGI_VID, PCI_DEVICE_EPCJ_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	3 },
+	{       DIGI_VID, PCI_DEVICE_920_2_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	4 },
+	{       DIGI_VID, PCI_DEVICE_920_4_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	5 },
+	{       DIGI_VID, PCI_DEVICE_920_8_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	6 },
+	{       DIGI_VID, PCI_DEVICE_XR_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	7 },
+	{       DIGI_VID, PCI_DEVICE_XRJ_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	8 },
+	{       DIGI_VID, PCI_DEVICE_XR_422_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	9 },
+	{       DIGI_VID, PCI_DEVICE_XR_IBM_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	10 },
+	{       DIGI_VID, PCI_DEVICE_XR_SAIP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	11 },
+	{       DIGI_VID, PCI_DEVICE_XR_BULL_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	12 },
+	{       DIGI_VID, PCI_DEVICE_920_8_HP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13 },
+	{       DIGI_VID, PCI_DEVICE_XEM_HP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	14 },
+	{0,}					/* 0 terminated list. */
+};
+MODULE_DEVICE_TABLE(pci, dgap_pci_tbl);
+
+/*
+ * A generic list of Product names, PCI Vendor ID, and PCI Device ID.
+ */
+struct board_id {
+	uint config_type;
+	uchar *name;
+	uint maxports;
+	uint dpatype;
+};
+
+static struct board_id dgap_Ids[] =
+{
+	{	PPCM,		PCI_DEVICE_XEM_NAME,	64,	(T_PCXM | T_PCLITE | T_PCIBUS)	},
+	{	PCX,		PCI_DEVICE_CX_NAME,	128,	(T_CX | T_PCIBUS)		},
+	{	PCX,		PCI_DEVICE_CX_IBM_NAME,	128,	(T_CX | T_PCIBUS)		},
+	{	PEPC,		PCI_DEVICE_EPCJ_NAME,	224,	(T_EPC  | T_PCIBUS)		},
+	{	APORT2_920P,	PCI_DEVICE_920_2_NAME,	2,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	APORT4_920P,	PCI_DEVICE_920_4_NAME,	4,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	APORT8_920P,	PCI_DEVICE_920_8_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XR_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XRJ_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XR_422_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XR_IBM_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XR_SAIP_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PAPORT8,	PCI_DEVICE_XR_BULL_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	APORT8_920P,	PCI_DEVICE_920_8_HP_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
+	{	PPCM,		PCI_DEVICE_XEM_HP_NAME,	64,	(T_PCXM | T_PCLITE | T_PCIBUS)	},
+	{0,}						/* 0 terminated list. */
+};
+
+static struct pci_driver dgap_driver = {
+	.name		= "dgap",
+	.probe		= dgap_init_one,
+	.id_table	= dgap_pci_tbl,
+	.remove		= dgap_remove_one,
+};
+
+struct firmware_info {
+        uchar *conf_name;       /* dgap.conf */	
+	uchar *bios_name;	/* BIOS filename */
+        uchar *fep_name;	/* FEP  filename */
+	uchar *con_name;	/* Concentrator filename  FIXME*/ 
+	int num;                /* sequence number */
+};
+
+/*
+ * Firmware - BIOS, FEP, and CONC filenames
+ */
+#define _CONFIG_ "dgap/dgap.conf"
+static struct firmware_info fw_info[] = {
+	{ _CONFIG_, "dgap/sxbios.bin",  "dgap/sxfep.bin",  0, 0 },	/* XEM_DID */
+	{ _CONFIG_, "dgap/cxpbios.bin", "dgap/cxpfep.bin", 0, 1 },	/* CX_DID  */           
+	{ _CONFIG_, "dgap/cxpbios.bin", "dgap/cxpfep.bin", 0, 2 },	/* CX_IBM_DID */         
+	{ _CONFIG_, "dgap/pcibios.bin", "dgap/pcifep.bin", 0, 3 },	/* EPCJ_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 4 }, 	/* 920_2_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 5 },	/* 920_4_DID */	
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 6 },	/* 920_8_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 7 },	/* XR_DID */ 
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 8 },	/* XRJ_DID */ 
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 9 },	/* XR_422_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 10 },	/* XR_IBM_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 11 },	/* XR_SAIP_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 12 },	/* XR_BULL_DID */
+	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 13 },	/* 920_8_HP_DID */
+	{ _CONFIG_, "dgap/sxbios.bin",  "dgap/sxfep.bin",  0, 14 },	/* XEM_HP_DID */
+	{0,}
+};
+
+struct toklist {
+	int	token;
+	char	*string;
+};
+
+static struct toklist dgap_tlist[] = {
+	{	BEGIN,		"config_begin"			},
+	{	END,		"config_end"			},
+	{	BOARD,		"board"				},
+	{	PCX,		"Digi_AccelePort_C/X_PCI"	},	/* C/X_PCI */
+	{	PEPC,		"Digi_AccelePort_EPC/X_PCI"	},	/* EPC/X_PCI */
+	{	PPCM,		"Digi_AccelePort_Xem_PCI"	},	/* PCI/Xem */
+	{	APORT2_920P,	"Digi_AccelePort_2r_920_PCI"	},
+	{	APORT4_920P,	"Digi_AccelePort_4r_920_PCI"	},
+	{	APORT8_920P,	"Digi_AccelePort_8r_920_PCI"	},
+	{	PAPORT4,	"Digi_AccelePort_4r_PCI(EIA-232/RS-422)" },
+	{	PAPORT8,	"Digi_AccelePort_8r_PCI(EIA-232/RS-422)" },
+	{	IO,		"io"				},
+	{	PCIINFO,	"pciinfo"			},
+	{	LINE,		"line"				},
+	{	CONC,		"conc"				},
+	{	CONC,		"concentrator"			},
+	{	CX,		"cx"				},
+	{	CX,		"ccon"				},
+	{	EPC,		"epccon"			},
+	{	EPC,		"epc"				},
+	{	MOD,		"module"			},
+	{	ID,		"id"				},
+	{	STARTO,		"start"				},
+	{	SPEED,		"speed"				},
+	{	CABLE,		"cable"				},
+	{	CONNECT,	"connect"			},
+	{	METHOD,		"method"			},
+	{	STATUS,		"status"			},
+	{	CUSTOM,		"Custom"			},
+	{	BASIC,		"Basic"				},
+	{	MEM,		"mem"				},
+	{	MEM,		"memory"			},
+	{	PORTS,		"ports"				},
+	{	MODEM,		"modem"				},
+	{	NPORTS,		"nports"			},
+	{	TTYN,		"ttyname"			},
+	{	CU,		"cuname"			},
+	{	PRINT,		"prname"			},
+	{	CMAJOR,		"major"				},
+	{	ALTPIN,		"altpin"			},
+	{	USEINTR,	"useintr"			},
+	{	TTSIZ,		"ttysize"			},
+	{	CHSIZ,		"chsize"			},
+	{	BSSIZ,		"boardsize"			},
+	{	UNTSIZ,		"schedsize"			},
+	{	F2SIZ,		"f2200size"			},
+	{	VPSIZ,		"vpixsize"			},
+	{	0,		NULL				}
+};
+
+char *dgap_state_text[] = {
+	"Board Failed",
+	"Configuration for board not found.\n\t\t\tRun mpi to configure board.",
+	"Board Found",
+	"Need Reset",
+	"Finished Reset",
+	"Need Config",
+	"Finished Config",
+	"Need Device Creation",
+	"Requested Device Creation",
+	"Finished Device Creation",
+	"Need BIOS Load", 
+	"Requested BIOS", 
+	"Doing BIOS Load",
+	"Finished BIOS Load",
+	"Need FEP Load", 
+	"Requested FEP",
+	"Doing FEP Load",
+	"Finished FEP Load",
+	"Requested PROC creation",
+	"Finished PROC creation",
+	"Board READY",
+};
+
+char *dgap_driver_state_text[] = {
+	"Driver Initialized",
+	"Driver needs configuration load.",
+	"Driver requested configuration from download daemon.",
+	"Driver Ready."
+};
+
+/*
+ * internal variables
+ */
+static struct board_t	*dgap_BoardsByMajor[256];
+static uchar		*dgap_TmpWriteBuf = NULL;
+static DECLARE_MUTEX(dgap_TmpWriteSem);
+
+/*
+ * Default transparent print information.
+ */
+static struct digi_t dgap_digi_init = {
+	.digi_flags =	DIGI_COOK,	/* Flags			*/
+	.digi_maxcps =	100,		/* Max CPS			*/
+	.digi_maxchar =	50,		/* Max chars in print queue	*/
+	.digi_bufsize =	100,		/* Printer buffer size		*/
+	.digi_onlen =	4,		/* size of printer on string	*/
+	.digi_offlen =	4,		/* size of printer off string	*/
+	.digi_onstr =	"\033[5i",	/* ANSI printer on string ]	*/
+	.digi_offstr =	"\033[4i",	/* ANSI printer off string ]	*/
+	.digi_term =	"ansi"		/* default terminal type	*/
+};
+
+
+/*
+ * Define a local default termios struct. All ports will be created
+ * with this termios initially.
+ *
+ * This defines a raw port at 9600 baud, 8 data bits, no parity,
+ * 1 stop bit.
+ */
+
+static struct ktermios DgapDefaultTermios =
+{
+	.c_iflag =	(DEFAULT_IFLAGS),	/* iflags */
+	.c_oflag =	(DEFAULT_OFLAGS),	/* oflags */
+	.c_cflag =	(DEFAULT_CFLAGS),	/* cflags */
+	.c_lflag =	(DEFAULT_LFLAGS),	/* lflags */
+	.c_cc =		INIT_C_CC,
+	.c_line = 	0,
+};
+
+
+/************************************************************************
+ *
+ * Driver load/unload functions
+ *
+ ************************************************************************/
+
+/*
+ * init_module()
+ *
+ * Module load.  This is where it all starts.
+ */
+int dgap_init_module(void)
+{
+	int rc = 0;
+
+	APR(("%s, Digi International Part Number %s\n", DG_NAME, DG_PART));
+
+	dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
+	
+	/*
+	 * Initialize global stuff
+	 */
+	rc = dgap_start();
+
+	if (rc < 0) 
+		return(rc);
+
+	/*
+	 * Find and configure all the cards
+	 */
+	rc = dgap_init_pci();
+
+	/*
+	 * If something went wrong in the scan, bail out of driver.
+	 */
+	if (rc < 0) {
+		/* Only unregister the pci driver if it was actually registered. */
+		if (dgap_NumBoards)
+			pci_unregister_driver(&dgap_driver);
+		else
+			printk("WARNING: dgap driver load failed.  No DGAP boards found.\n");
+
+		dgap_cleanup_module();
+	} else {
+		dgap_create_driver_sysfiles(&dgap_driver);
+		dgap_driver_state = DRIVER_READY;
+	}
+  
+	DPR_INIT(("Finished init_module. Returning %d\n", rc));
+	return (rc);
+}
+
+/*
+ * Start of driver.
+ */
+static int dgap_start(void)
+{
+	int rc = 0;
+	unsigned long flags;
+
+	if (dgap_driver_start == FALSE) {
+
+		dgap_driver_start = TRUE;
+
+	        /* make sure that the globals are init'd before we do anything else */
+	        dgap_init_globals();
+
+		dgap_NumBoards = 0;
+
+		APR(("For the tools package or updated drivers please visit http://www.digi.com\n";));
+
+		/*
+		 * Register our base character device into the kernel.
+		 * This allows the download daemon to connect to the downld device
+		 * before any of the boards are init'ed.
+		 */
+		if (!dgap_Major_Control_Registered) {
+			/*
+			 * Register management/dpa devices
+			 */
+			rc = register_chrdev(DIGI_DGAP_MAJOR, "dgap", &DgapBoardFops);
+			if (rc < 0) {
+				APR(("Can't register dgap driver device (%d)\n", rc));
+				return (rc);
+			}
+
+			dgap_class = class_create(THIS_MODULE, "dgap_mgmt");
+			device_create(dgap_class, NULL,
+				MKDEV(DIGI_DGAP_MAJOR, 0),
+				NULL, "dgap_mgmt");
+			dgap_Major_Control_Registered = TRUE;
+		}
+
+		/*
+		 * Init any global tty stuff.
+		 */
+		rc = dgap_tty_preinit();
+
+		if (rc < 0) {
+			APR(("tty preinit - not enough memory (%d)\n", rc));
+			return(rc); 
+		}
+
+		/* Start the poller */
+		DGAP_LOCK(dgap_poll_lock, flags);
+		init_timer(&dgap_poll_timer);
+		dgap_poll_timer.function = dgap_poll_handler;
+		dgap_poll_timer.data = 0;
+		dgap_poll_time = jiffies + dgap_jiffies_from_ms(dgap_poll_tick);
+		dgap_poll_timer.expires = dgap_poll_time;
+		DGAP_UNLOCK(dgap_poll_lock, flags);
+
+		add_timer(&dgap_poll_timer);
+
+		dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
+	}
+
+	return (rc);
+}
+
+/*
+ * Register pci driver, and return how many boards we have.
+ */
+static int dgap_init_pci(void)
+{
+	return pci_register_driver(&dgap_driver);
+}
+
+/* returns count (>= 0), or negative on error */
+static int dgap_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	int rc;
+
+	/* wake up and enable device */
+	rc = pci_enable_device(pdev);
+
+	if (rc < 0) {
+		rc = -EIO;
+	} else {  
+		rc = dgap_probe1(pdev, ent->driver_data);
+		if (rc == 0) {
+			dgap_NumBoards++;
+			DPR_INIT(("Incrementing numboards to %d\n", dgap_NumBoards));
+			rc = dgap_firmware_load(pdev, ent->driver_data);
+		}
+	}
+	return rc;
+}               
+
+static int dgap_probe1(struct pci_dev *pdev, int card_type)
+{
+	return dgap_found_board(pdev, card_type);
+}
+         
+static void dgap_remove_one(struct pci_dev *dev)
+{
+	/* Do Nothing */
+}
+
+/*
+ * dgap_cleanup_module()
+ *
+ * Module unload.  This is where it all ends.
+ */
+void dgap_cleanup_module(void)
+{
+	int i;
+	ulong lock_flags;
+
+	DGAP_LOCK(dgap_poll_lock, lock_flags);
+	dgap_poll_stop = 1;
+	DGAP_UNLOCK(dgap_poll_lock, lock_flags);
+
+	/* Turn off poller right away. */
+	del_timer_sync(&dgap_poll_timer);
+
+	dgap_remove_driver_sysfiles(&dgap_driver);
+
+
+	if (dgap_Major_Control_Registered) {
+		device_destroy(dgap_class, MKDEV(DIGI_DGAP_MAJOR, 0));
+		device_destroy(dgap_class, MKDEV(DIGI_DGAP_MAJOR, 1));
+		class_destroy(dgap_class);
+		unregister_chrdev(DIGI_DGAP_MAJOR, "dgap");
+	}
+
+	kfree(dgap_config_buf);
+
+	for (i = 0; i < dgap_NumBoards; ++i) {
+		dgap_remove_ports_sysfiles(dgap_Board[i]);
+		dgap_tty_uninit(dgap_Board[i]);
+		dgap_cleanup_board(dgap_Board[i]);
+	}
+
+	dgap_tty_post_uninit();
+
+#if defined(DGAP_TRACER)
+	/* last thing, make sure we release the tracebuffer */
+	dgap_tracer_free();
+#endif
+	if (dgap_NumBoards)
+		pci_unregister_driver(&dgap_driver);
+}
+
+/*
+ * dgap_cleanup_board()
+ *
+ * Free all the memory associated with a board
+ */
+static void dgap_cleanup_board(struct board_t *brd)
+{
+	int i = 0;
+
+        if(!brd || brd->magic != DGAP_BOARD_MAGIC)
+                return;
+
+	if (brd->intr_used && brd->irq)
+		free_irq(brd->irq, brd);
+
+	tasklet_kill(&brd->helper_tasklet);
+
+	if (brd->re_map_port) {
+		release_mem_region(brd->membase + 0x200000, 0x200000);
+		iounmap(brd->re_map_port);
+		brd->re_map_port = NULL;
+	}
+
+	if (brd->re_map_membase) {
+		release_mem_region(brd->membase, 0x200000);
+		iounmap(brd->re_map_membase);
+		brd->re_map_membase = NULL;
+	}
+
+        if (brd->msgbuf_head) {
+                unsigned long flags;
+
+                DGAP_LOCK(dgap_global_lock, flags);
+                brd->msgbuf = NULL;
+                printk("%s", brd->msgbuf_head);
+                kfree(brd->msgbuf_head);
+                brd->msgbuf_head = NULL;
+                DGAP_UNLOCK(dgap_global_lock, flags);
+        }
+
+	/* Free all allocated channels structs */
+	for (i = 0; i < MAXPORTS ; i++) {
+		if (brd->channels[i]) {
+			kfree(brd->channels[i]);
+			brd->channels[i] = NULL;
+		}
+	}
+
+	kfree(brd->flipbuf);
+	kfree(brd->flipflagbuf);
+
+	dgap_Board[brd->boardnum] = NULL;
+
+        kfree(brd);
+}
+
+/*
+ * dgap_found_board()
+ *
+ * A board has been found, init it.
+ */
+static int dgap_found_board(struct pci_dev *pdev, int id)
+{
+	struct board_t *brd;
+	unsigned int pci_irq;
+	int i = 0;
+	unsigned long flags;
+
+	/* get the board structure and prep it */
+	brd = dgap_Board[dgap_NumBoards] =
+	(struct board_t *) dgap_driver_kzmalloc(sizeof(struct board_t), GFP_KERNEL);
+	if (!brd) {
+		APR(("memory allocation for board structure failed\n"));
+		return(-ENOMEM);
+	}
+
+	/* make a temporary message buffer for the boot messages */
+	brd->msgbuf = brd->msgbuf_head =
+		(char *) dgap_driver_kzmalloc(sizeof(char) * 8192, GFP_KERNEL);
+	if(!brd->msgbuf) {
+		kfree(brd);
+		APR(("memory allocation for board msgbuf failed\n"));
+		return(-ENOMEM);
+	}
+
+	/* store the info for the board we've found */
+	brd->magic = DGAP_BOARD_MAGIC;
+	brd->boardnum = dgap_NumBoards;
+	brd->firstminor = 0;
+	brd->vendor = dgap_pci_tbl[id].vendor;
+	brd->device = dgap_pci_tbl[id].device;
+	brd->pdev = pdev;
+	brd->pci_bus = pdev->bus->number;
+	brd->pci_slot = PCI_SLOT(pdev->devfn);
+	brd->name = dgap_Ids[id].name;
+	brd->maxports = dgap_Ids[id].maxports;
+	brd->type = dgap_Ids[id].config_type;
+	brd->dpatype = dgap_Ids[id].dpatype;
+	brd->dpastatus = BD_NOFEP;
+	init_waitqueue_head(&brd->state_wait);
+
+	DGAP_SPINLOCK_INIT(brd->bd_lock);
+
+	brd->state		= BOARD_FOUND;
+	brd->runwait		= 0;
+	brd->inhibit_poller	= FALSE;
+	brd->wait_for_bios	= 0;
+	brd->wait_for_fep	= 0;
+
+	for (i = 0; i < MAXPORTS; i++) 
+		brd->channels[i] = NULL;
+
+	/* store which card & revision we have */
+	pci_read_config_word(pdev, PCI_SUBSYSTEM_VENDOR_ID, &brd->subvendor);
+	pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &brd->subdevice);
+	pci_read_config_byte(pdev, PCI_REVISION_ID, &brd->rev);
+
+	pci_irq = pdev->irq;
+	brd->irq = pci_irq;
+
+	/* get the PCI Base Address Registers */
+
+	if (brd->device == PCI_DEVICE_XRJ_DID || brd->device == PCI_DEVICE_EPCJ_DID) {
+		/* Xr Jupiter and EPC use BAR 2 */
+		brd->membase     = pci_resource_start(pdev, 2);
+		brd->membase_end = pci_resource_end(pdev, 2);
+	} else {		
+		/* Everyone else uses BAR 0 */
+		brd->membase     = pci_resource_start(pdev, 0);
+		brd->membase_end = pci_resource_end(pdev, 0);
+	}
+
+	if (!brd->membase) {
+		APR(("card has no PCI IO resources, failing board.\n"));
+		return -ENODEV;
+	}
+
+	if (brd->membase & 1)
+		brd->membase &= ~3;
+	else
+		brd->membase &= ~15;
+
+	/*
+	 * On the PCI boards, there is no IO space allocated
+	 * The I/O registers will be in the first 3 bytes of the
+	 * upper 2MB of the 4MB memory space.  The board memory
+	 * will be mapped into the low 2MB of the 4MB memory space
+	 */
+	brd->port = brd->membase + PCI_IO_OFFSET;
+	brd->port_end = brd->port + PCI_IO_SIZE;
+
+	/*
+	 * Special initialization for non-PLX boards
+	 */
+	if (brd->device != PCI_DEVICE_XRJ_DID && brd->device != PCI_DEVICE_EPCJ_DID) {
+		unsigned short cmd;
+
+		pci_write_config_byte(pdev, 0x40, 0);
+		pci_write_config_byte(pdev, 0x46, 0);
+
+		/* Limit burst length to 2 doubleword transactions */ 
+		pci_write_config_byte(pdev, 0x42, 1);
+
+		/*
+		 * Enable IO and mem if not already done.
+		 * This was needed for support on Itanium.
+		 */
+		pci_read_config_word(pdev, PCI_COMMAND, &cmd);
+		cmd |= (PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
+		pci_write_config_word(pdev, PCI_COMMAND, cmd);
+	}
+
+	/* init our poll helper tasklet */
+	tasklet_init(&brd->helper_tasklet, dgap_poll_tasklet, (unsigned long) brd);
+
+	 /* Log the information about the board */
+	dgap_mbuf(brd, DRVSTR": board %d: %s (rev %d), irq %d\n",
+		dgap_NumBoards, brd->name, brd->rev, brd->irq);
+
+	DPR_INIT(("dgap_scan(%d) - printing out the msgbuf\n", i));
+	DGAP_LOCK(dgap_global_lock, flags);
+	brd->msgbuf = NULL;
+	printk("%s", brd->msgbuf_head);
+	kfree(brd->msgbuf_head);
+	brd->msgbuf_head = NULL;
+	DGAP_UNLOCK(dgap_global_lock, flags);
+
+	i = dgap_do_remap(brd);
+	if (i)
+		brd->state = BOARD_FAILED;
+	else
+		brd->state = NEED_RESET;
+
+        return 0;
+}
+
+int dgap_finalize_board_init(struct board_t *brd) {
+
+        int rc;
+
+        DPR_INIT(("dgap_finalize_board_init() - start\n"));
+
+	if (!brd || brd->magic != DGAP_BOARD_MAGIC)
+                return(-ENODEV);
+
+        DPR_INIT(("dgap_finalize_board_init() - start #2\n"));
+
+	brd->use_interrupts = dgap_config_get_useintr(brd);
+
+	/*
+	 * Set up our interrupt handler if we are set to do interrupts.
+	 */
+	if (brd->use_interrupts && brd->irq) {
+
+		rc = request_irq(brd->irq, dgap_intr, IRQF_SHARED, "DGAP", brd);
+
+		if (rc) {
+			dgap_mbuf(brd, DRVSTR": Failed to hook IRQ %d. Board will work in poll mode.\n",
+                                  brd->irq);
+			brd->intr_used = 0;
+		} else
+			brd->intr_used = 1;
+	} else 
+		brd->intr_used = 0;
+
+	return(0);
+}
+
+static int dgap_firmware_load(struct pci_dev *pdev, int card_type)
+{
+	struct board_t *brd = dgap_Board[dgap_NumBoards - 1];
+	const struct firmware *fw;
+	char *uaddr;
+	int ret;
+	
+	dgap_get_vpd(brd);
+	dgap_do_reset_board(brd);
+
+	if ((fw_info[card_type].conf_name) && 
+	    (dgap_driver_state == DRIVER_NEED_CONFIG_LOAD)) {
+		ret = request_firmware(&fw, fw_info[card_type].conf_name, &pdev->dev);
+		if (ret) {
+			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
+					"you've placed '%s' file into your firmware "
+					"loader directory (e.g. /lib/firmware)\n",
+					fw_info[card_type].conf_name);
+			return ret; 
+		} else {
+			if (!dgap_config_buf) {
+				uaddr = dgap_config_buf = dgap_driver_kzmalloc(fw->size + 1, GFP_ATOMIC);
+				if (!dgap_config_buf) {
+					DPR_INIT(("DGAP: dgap_firmware_load - unable to allocate memory for config file\n"));
+					release_firmware(fw);
+					return -ENOMEM;
+				}
+			}
+
+			memcpy(uaddr, fw->data, fw->size);
+			release_firmware(fw);
+			uaddr[fw->size + 1] = '\0'; 	// The config file is treated as a string
+
+			if (dgap_parsefile(&uaddr, TRUE) != 0) 
+				return -EINVAL;
+
+			dgap_driver_state = -1;
+		}
+	}
+
+	ret = dgap_after_config_loaded(brd->boardnum);
+	if (ret != 0)
+		return ret;
+	/*
+	 * Match this board to a config the user created for us.
+	 */
+	brd->bd_config = dgap_find_config(brd->type, brd->pci_bus, brd->pci_slot);
+
+	/*
+	 * Because the 4 port Xr products share the same PCI ID
+	 * as the 8 port Xr products, if we receive a NULL config
+	 * back, and this is a PAPORT8 board, retry with a
+	 * PAPORT4 attempt as well.
+	 */
+	if (brd->type == PAPORT8 && !brd->bd_config)
+		brd->bd_config = dgap_find_config(PAPORT4, brd->pci_bus, brd->pci_slot);
+
+	if (!brd->bd_config) {
+		printk(KERN_ERR "DGAP: dgap_firmware_load: No valid configuration found\n");
+		return -EINVAL;
+	}
+
+	dgap_tty_register(brd);
+	dgap_finalize_board_init(brd);
+
+	if (fw_info[card_type].bios_name) {
+		ret = request_firmware(&fw, fw_info[card_type].bios_name, &pdev->dev);
+		if (ret) {
+			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
+					"you've placed '%s' file into your firmware "
+					"loader directory (e.g. /lib/firmware)\n",
+					fw_info[card_type].bios_name);
+			return ret;
+		} else {
+			uaddr = (char *)fw->data;
+			dgap_do_bios_load(brd, uaddr, fw->size);
+			release_firmware(fw);
+
+			/* Wait for BIOS to test board... */
+			dgap_do_wait_for_bios(brd);
+
+			if (brd->state != FINISHED_BIOS_LOAD)
+				return -ENXIO;
+		}
+	}
+
+        if (fw_info[card_type].fep_name) {
+                ret = request_firmware(&fw, fw_info[card_type].fep_name, &pdev->dev);
+                if (ret) {
+                        printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
+                                        "you've placed '%s' file into your firmware "
+                                        "loader directory (e.g. /lib/firmware)\n",
+                                        fw_info[card_type].fep_name);
+                        return ret;
+                } else {
+                        uaddr = (char *)fw->data;
+                        dgap_do_fep_load(brd, uaddr, fw->size);
+			release_firmware(fw);
+
+                        /* Wait for FEP to load on board... */
+                        dgap_do_wait_for_fep(brd);
+
+                        if (brd->state != FINISHED_FEP_LOAD)
+                                return -ENXIO;
+                }
+        }
+
+#ifdef DIGI_CONCENTRATORS_SUPPORTED
+	/*
+	 * If this is a CX or EPCX, we need to see if the firmware
+	 * is requesting a concentrator image from us.
+	 */
+	if ((bd->type == PCX) || (bd->type == PEPC)) {
+		chk_addr = (u16 *) (vaddr + DOWNREQ);
+		/* Nonzero if FEP is requesting concentrator image. */
+		check = readw(chk_addr);
+		vaddr = brd->re_map_membase;
+	}
+
+	if (fw_info[card_type].con_name && check && vaddr) {
+		ret = request_firmware(&fw, fw_info[card_type].con_name, &pdev->dev);
+		if (ret) {
+			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
+					"you've placed '%s' file into your firmware "
+					"loader directory (e.g. /lib/firmware)\n",
+					fw_info[card_type].con_name);
+			return ret;
+		} else {
+			/* Put concentrator firmware loading code here */
+			offset = readw((u16 *) (vaddr + DOWNREQ)); 
+        		memcpy_toio(offset, fw->data, fw->size);
+
+                        uaddr = (char *)fw->data;
+			dgap_do_conc_load(brd, uaddr, fw->size)
+			release_firmware(fw);
+		}
+	}
+#endif
+	/*
+	 * Do tty device initialization.
+	 */
+	ret = dgap_tty_init(brd); 
+	if (ret < 0) {
+		dgap_tty_uninit(brd);
+        	printk("DGAP: dgap_firmware_load: Can't init tty devices (%d)\n", ret);
+		return -EIO;
+	}
+
+	dgap_sysfs_create(brd);
+
+	brd->state = BOARD_READY;
+	brd->dpastatus = BD_RUNNING;
+
+	return 0;
+}
+
+/*
+ * Remap PCI memory.
+ */
+static int dgap_do_remap(struct board_t *brd)
+{
+	if (!brd || brd->magic != DGAP_BOARD_MAGIC)
+		return -ENXIO;
+
+	if (!request_mem_region(brd->membase, 0x200000, "dgap")) {
+		APR(("dgap: mem_region %lx already in use.\n", brd->membase));
+		return -ENOMEM;
+        }
+
+	if (!request_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000, "dgap")) {
+		APR(("dgap: mem_region IO %lx already in use.\n",
+			brd->membase + PCI_IO_OFFSET));
+		release_mem_region(brd->membase, 0x200000);
+		return -ENOMEM;
+        }
+
+	brd->re_map_membase = ioremap(brd->membase, 0x200000);
+	if (!brd->re_map_membase) {
+		APR(("dgap: ioremap mem %lx cannot be mapped.\n", brd->membase));
+		release_mem_region(brd->membase, 0x200000);
+		release_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000);
+		return -ENOMEM;
+	}
+
+	brd->re_map_port = ioremap((brd->membase + PCI_IO_OFFSET), 0x200000);
+	if (!brd->re_map_port) {
+		release_mem_region(brd->membase, 0x200000);
+		release_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000);
+		iounmap(brd->re_map_membase);
+		APR(("dgap: ioremap IO mem %lx cannot be mapped.\n",
+			brd->membase + PCI_IO_OFFSET));
+		return -ENOMEM;
+	}
+
+	DPR_INIT(("remapped io: 0x%p  remapped mem: 0x%p\n",
+		brd->re_map_port, brd->re_map_membase));
+	return 0;
+}
+
+/*****************************************************************************
+*
+* Function:
+*                                       
+*    dgap_poll_handler
+*
+* Author:
+*
+*    Scott H Kilau
+*       
+* Parameters:
+*
+*    dummy -- ignored                    
+*
+* Return Values:
+*
+*    none
+*
+* Description:   
+*                                       
+*    As each timer expires, it determines (a) whether the "transmit"
+*    waiter needs to be woken up, and (b) whether the poller needs to
+*    be rescheduled.
+*
+******************************************************************************/
+
+static void dgap_poll_handler(ulong dummy)
+{
+	int i;
+        struct board_t *brd;
+        unsigned long lock_flags;
+        ulong new_time;
+
+	dgap_poll_counter++;
+
+	/*
+	 * Do not start the board state machine until
+	 * driver tells us its up and running, and has
+	 * everything it needs.
+	 */
+	if (dgap_driver_state != DRIVER_READY)
+		goto schedule_poller;
+	
+	/*
+	 * If we have just 1 board, or the system is not SMP,
+	 * then use the typical old style poller.
+	 * Otherwise, use our new tasklet based poller, which should
+	 * speed things up for multiple boards.
+	 */
+	if ((dgap_NumBoards == 1) || (num_online_cpus() <= 1)) {
+		for (i = 0; i < dgap_NumBoards; i++) {
+
+			brd = dgap_Board[i];
+
+			if (brd->state == BOARD_FAILED) 
+				continue;
+			
+			if (!brd->intr_running) 
+				/* Call the real board poller directly */
+				dgap_poll_tasklet((unsigned long) brd);
+			
+		}
+	} else {
+		/* Go thru each board, kicking off a tasklet for each if needed */
+		for (i = 0; i < dgap_NumBoards; i++) {
+			brd = dgap_Board[i];
+
+			/*
+			 * Attempt to grab the board lock.
+			 *
+			 * If we can't get it, no big deal, the next poll will get it.
+			 * Basically, I just really don't want to spin in here, because I want
+			 * to kick off my tasklets as fast as I can, and then get out the poller.
+			 */
+			if (!spin_trylock(&brd->bd_lock)) 
+				continue;
+
+			/* If board is in a failed state, don't bother scheduling a tasklet */
+			if (brd->state == BOARD_FAILED) {
+				spin_unlock(&brd->bd_lock);
+				continue;
+			}
+
+			/* Schedule a poll helper task */
+			if (!brd->intr_running) 
+				tasklet_schedule(&brd->helper_tasklet);
+
+			/*
+			 * Can't do DGAP_UNLOCK here, as we don't have
+			 * lock_flags because we did a trylock above.
+			 */
+			spin_unlock(&brd->bd_lock);
+		}
+	}
+
+schedule_poller:
+
+	/*
+	 * Schedule ourself back at the nominal wakeup interval.
+	 */
+	DGAP_LOCK(dgap_poll_lock, lock_flags);
+	dgap_poll_time +=  dgap_jiffies_from_ms(dgap_poll_tick);
+
+	new_time = dgap_poll_time - jiffies;
+
+	if ((ulong) new_time >= 2 * dgap_poll_tick) 
+		dgap_poll_time = jiffies +  dgap_jiffies_from_ms(dgap_poll_tick);
+
+	dgap_poll_timer.function = dgap_poll_handler;
+	dgap_poll_timer.data = 0;
+	dgap_poll_timer.expires = dgap_poll_time;
+	DGAP_UNLOCK(dgap_poll_lock, lock_flags);
+
+	if (!dgap_poll_stop)
+		add_timer(&dgap_poll_timer);
+}
+
+/*
+ * dgap_intr()
+ *
+ * Driver interrupt handler.
+ */
+static irqreturn_t dgap_intr(int irq, void *voidbrd)
+{
+	struct board_t *brd = (struct board_t *) voidbrd;
+
+	if (!brd) {
+		APR(("Received interrupt (%d) with null board associated\n", irq));
+		return IRQ_NONE;
+	}
+
+	/*
+	 * Check to make sure its for us.
+	 */
+	if (brd->magic != DGAP_BOARD_MAGIC) {
+		APR(("Received interrupt (%d) with a board pointer that wasn't ours!\n", irq));
+		return IRQ_NONE;
+	}
+
+	brd->intr_count++;
+
+	/*
+	 * Schedule tasklet to run at a better time.
+	 */
+	tasklet_schedule(&brd->helper_tasklet);
+	return IRQ_HANDLED;
+}
+
+/*
+ * dgap_init_globals()
+ *
+ * This is where we initialize the globals from the static insmod
+ * configuration variables.  These are declared near the head of
+ * this file.
+ */
+static void dgap_init_globals(void)
+{
+	int i = 0;
+
+	dgap_rawreadok		= rawreadok;
+	dgap_debug		= debug;
+
+	for (i = 0; i < MAXBOARDS; i++) 
+		dgap_Board[i] = NULL;
+
+	init_timer(&dgap_poll_timer); 
+
+	init_waitqueue_head(&dgap_dl_wait);
+	dgap_dl_action = 0;
+}
+
+/************************************************************************
+ *
+ * Utility functions
+ *
+ ************************************************************************/
+
+/*
+ * dgap_driver_kzmalloc()
+ *
+ * Malloc and clear memory,
+ */
+void *dgap_driver_kzmalloc(size_t size, int priority)
+{
+ 	void *p = kmalloc(size, priority);
+	if(p)
+		memset(p, 0, size);
+	return(p);
+}
+
+/*
+ * dgap_mbuf()
+ *
+ * Used to print to the message buffer during board init.
+ */
+static void dgap_mbuf(struct board_t *brd, const char *fmt, ...) {
+	va_list		ap;
+	char		buf[1024];
+	int		i;
+	unsigned long	flags;
+	size_t		length;
+
+	DGAP_LOCK(dgap_global_lock, flags);
+
+	/* Format buf using fmt and arguments contained in ap. */
+	va_start(ap, fmt);
+	i = vsnprintf(buf, sizeof(buf), fmt,  ap);
+	va_end(ap);
+
+	DPR((buf));
+
+	if (!brd || !brd->msgbuf) {
+		printk("%s", buf);
+		DGAP_UNLOCK(dgap_global_lock, flags);
+		return;
+	}
+
+	length = strlen(buf) + 1;
+	if (brd->msgbuf - brd->msgbuf_head < length)
+		length = brd->msgbuf - brd->msgbuf_head;
+	memcpy(brd->msgbuf, buf, length);
+	brd->msgbuf += length;
+
+	DGAP_UNLOCK(dgap_global_lock, flags);
+}
+
+/*
+ * dgap_ms_sleep()
+ *
+ * Put the driver to sleep for x ms's
+ *
+ * Returns 0 if timed out, !0 (showing signal) if interrupted by a signal.
+ */
+int dgap_ms_sleep(ulong ms)
+{
+	current->state = TASK_INTERRUPTIBLE;
+	schedule_timeout((ms * HZ) / 1000);
+	return (signal_pending(current));
+}
+
+/*
+ *      dgap_ioctl_name() : Returns a text version of each ioctl value.
+ */
+char *dgap_ioctl_name(int cmd)
+{
+	switch(cmd) {
+
+	case TCGETA:		return("TCGETA");
+	case TCGETS:		return("TCGETS");
+	case TCSETA:		return("TCSETA");
+	case TCSETS:		return("TCSETS");
+	case TCSETAW:		return("TCSETAW");
+	case TCSETSW:		return("TCSETSW");
+	case TCSETAF:		return("TCSETAF");
+	case TCSETSF:		return("TCSETSF");
+	case TCSBRK:		return("TCSBRK");
+	case TCXONC:		return("TCXONC");
+	case TCFLSH:		return("TCFLSH");
+	case TIOCGSID:		return("TIOCGSID");
+
+	case TIOCGETD:		return("TIOCGETD");
+	case TIOCSETD:		return("TIOCSETD");
+	case TIOCGWINSZ:	return("TIOCGWINSZ");
+	case TIOCSWINSZ:	return("TIOCSWINSZ");
+
+	case TIOCMGET:		return("TIOCMGET");
+	case TIOCMSET:		return("TIOCMSET");
+	case TIOCMBIS:		return("TIOCMBIS");
+	case TIOCMBIC:		return("TIOCMBIC");
+
+	/* from digi.h */
+	case DIGI_SETA:		return("DIGI_SETA");
+	case DIGI_SETAW:	return("DIGI_SETAW");
+	case DIGI_SETAF:	return("DIGI_SETAF");
+	case DIGI_SETFLOW:	return("DIGI_SETFLOW");
+	case DIGI_SETAFLOW:	return("DIGI_SETAFLOW");
+	case DIGI_GETFLOW:	return("DIGI_GETFLOW");
+	case DIGI_GETAFLOW:	return("DIGI_GETAFLOW");
+	case DIGI_GETA:		return("DIGI_GETA");
+	case DIGI_GEDELAY:	return("DIGI_GEDELAY");
+	case DIGI_SEDELAY:	return("DIGI_SEDELAY");
+	case DIGI_GETCUSTOMBAUD: return("DIGI_GETCUSTOMBAUD");
+	case DIGI_SETCUSTOMBAUD: return("DIGI_SETCUSTOMBAUD");
+	case TIOCMODG:		return("TIOCMODG");
+	case TIOCMODS:		return("TIOCMODS");
+	case TIOCSDTR:		return("TIOCSDTR");
+	case TIOCCDTR:		return("TIOCCDTR");
+
+	default:		return("unknown");
+	}
+}
+ 
+/*
+ * Loads the dgap.conf config file from the user.
+ */
+void dgap_do_config_load(uchar __user *uaddr, int len)
+{
+	int orig_len = len;
+	char *to_addr;
+	uchar __user *from_addr = uaddr;
+	char buf[U2BSIZE];
+	int n;
+
+	to_addr = dgap_config_buf = dgap_driver_kzmalloc(len + 1, GFP_ATOMIC);
+	if (!dgap_config_buf) {
+		DPR_INIT(("dgap_do_config_load - unable to allocate memory for file\n"));
+		dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
+		return;
+	}
+
+	n = U2BSIZE;
+	while (len) {
+
+		if (n > len)
+			n = len;
+
+		if (copy_from_user((char *) &buf, from_addr, n) == -1)
+			return;
+
+		/* Copy data from buffer to kernel memory */
+		memcpy(to_addr, buf, n);
+
+		/* increment counts */
+		len -= n;
+		to_addr += n;
+		from_addr += n;
+		n = U2BSIZE;
+        }
+
+	dgap_config_buf[orig_len] = '\0';
+
+	to_addr = dgap_config_buf;
+	dgap_parsefile(&to_addr, TRUE);
+
+	DPR_INIT(("dgap_config_load() finish\n"));
+
+	return;
+}
+
+static int dgap_after_config_loaded(int board)
+{
+        int ret = 0;
+
+	/*
+	 * Initialize KME waitqueues...
+	 */
+	init_waitqueue_head(&(dgap_Board[board]->kme_wait));
+
+	/*
+	 * allocate flip buffer for board.
+	 */
+	dgap_Board[board]->flipbuf = dgap_driver_kzmalloc(MYFLIPLEN, GFP_ATOMIC);
+	if (!dgap_Board[board]->flipbuf) {
+		ret = -ENOMEM;
+		goto out;
+	}
+	dgap_Board[board]->flipflagbuf = dgap_driver_kzmalloc(MYFLIPLEN, GFP_ATOMIC);
+	if (!dgap_Board[board]->flipflagbuf) 
+		ret = -ENOMEM;
+
+    out:
+        return ret;
+}
+
+/*
+ * Create pr and tty device entries
+ */
+static void dgap_sysfs_create(struct board_t *brd)
+{
+	struct channel_t *ch;
+	int j = 0;
+
+	ch = brd->channels[0];
+	for (j = 0; j < brd->nasync; j++, ch = brd->channels[j]) {
+		struct device *classp;
+		classp = tty_register_device(brd->SerialDriver, j, &(ch->ch_bd->pdev->dev));
+		ch->ch_tun.un_sysfs = classp;
+		dgap_create_tty_sysfs(&ch->ch_tun, classp);
+
+		classp = tty_register_device(brd->PrintDriver, j, &(ch->ch_bd->pdev->dev));
+		ch->ch_pun.un_sysfs = classp;
+		dgap_create_tty_sysfs(&ch->ch_pun, classp);
+	}
+	dgap_create_ports_sysfiles(brd);
+}
+
+/*
+ * Copies the BIOS code from the user to the board,
+ * and starts the BIOS running.
+ */
+static void dgap_do_bios_load(struct board_t *brd, uchar *ubios, int len)
+{
+	uchar *addr;
+	uint offset;
+	int i;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
+		return;
+
+	DPR_INIT(("dgap_do_bios_load() start\n"));
+
+	addr = brd->re_map_membase;
+
+	/*
+	 * clear POST area
+	 */
+	for (i = 0; i < 16; i++)
+		writeb(0, addr + POSTAREA + i);
+                                
+	/*
+	 * Download bios
+	 */
+	offset = 0x1000;
+	memcpy_toio(addr + offset, ubios, len);
+
+	writel(0x0bf00401, addr);
+	writel(0, (addr + 4));
+
+	/* Clear the reset, and change states. */
+	writeb(FEPCLR, brd->re_map_port);
+}
+
+/*
+ * Checks to see if the BIOS completed running on the card.
+ */
+static void dgap_do_wait_for_bios(struct board_t *brd)
+{
+	uchar *addr;
+	u16 word;
+	u16 err1;
+	u16 err2;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
+		return;
+	
+	addr = brd->re_map_membase;
+	word = readw(addr + POSTAREA);
+
+	/*
+	 * It can take 5-6 seconds for a board to
+	 * pass the bios self test and post results.
+	 * Give it 10 seconds.
+	 */
+	brd->wait_for_bios = 0;
+	while (brd->wait_for_bios < 1000) {
+		/* Check to see if BIOS thinks board is good. (GD). */
+		if (word == *(u16 *) "GD") {
+			DPR_INIT(("GOT GD in memory, moving states.\n"));
+			brd->state = FINISHED_BIOS_LOAD;
+			return;
+		}
+		msleep_interruptible(10);
+		brd->wait_for_bios++;
+		word = readw(addr + POSTAREA);
+	}
+
+	/* Gave up on board after too long of time taken */
+	err1 = readw(addr + SEQUENCE);
+	err2 = readw(addr + ERROR);
+	APR(("***WARNING*** %s failed diagnostics.  Error #(%x,%x).\n",
+		brd->name, err1, err2));
+	brd->state = BOARD_FAILED;
+	brd->dpastatus = BD_NOBIOS;
+}
+
+/*
+ * Copies the FEP code from the user to the board,
+ * and starts the FEP running.
+ */
+static void dgap_do_fep_load(struct board_t *brd, uchar *ufep, int len)
+{
+	uchar *addr;
+	uint offset;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
+		return;
+
+	addr = brd->re_map_membase;
+
+	DPR_INIT(("dgap_do_fep_load() for board %s : start\n", brd->name));
+
+	/*
+	 * Download FEP
+	 */
+	offset = 0x1000;
+	memcpy_toio(addr + offset, ufep, len);
+
+	/*
+	 * If board is a concentrator product, we need to give
+	 * it its config string describing how the concentrators look.
+	 */
+	if ((brd->type == PCX) || (brd->type == PEPC)) {
+		uchar string[100];
+		uchar *config, *xconfig;
+		int i = 0;
+
+		xconfig = dgap_create_config_string(brd, string);
+
+		/* Write string to board memory */
+		config = addr + CONFIG;
+		for (; i < CONFIGSIZE; i++, config++, xconfig++) {
+			writeb(*xconfig, config);
+			if ((*xconfig & 0xff) == 0xff)
+				break;
+		}
+	}
+
+	writel(0xbfc01004, (addr + 0xc34));
+	writel(0x3, (addr + 0xc30));
+
+	DPR_INIT(("dgap_do_fep_load() for board %s : finish\n", brd->name));
+}
+
+/*
+ * Waits for the FEP to report thats its ready for us to use.
+ */
+void dgap_do_wait_for_fep(struct board_t *brd)
+{
+	uchar *addr;
+	u16 word;
+	u16 err1;
+	u16 err2;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
+		return;
+
+	addr = brd->re_map_membase;
+	word = readw(addr + FEPSTAT);
+
+	/*
+	 * It can take 2-3 seconds for the FEP to
+         * be up and running. Give it 5 secs.
+	 */
+	brd->wait_for_fep = 0;
+	while (brd->wait_for_fep < 500) {
+		/* Check to see if FEP is up and running now. */
+		if (word == *(u16 *) "OS") {
+			DPR_INIT(("GOT OS in memory for board %s, moving states.\n", brd->name));
+			brd->state = FINISHED_FEP_LOAD;
+			/*
+		 	* Check to see if the board can support FEP5+ commands.
+		 	*/
+			word = readw(addr + FEP5_PLUS);
+			if (word == *(u16 *) "5A") {
+				DPR_INIT(("GOT 5A in memory for board %s, board supports extended FEP5 commands.\n", brd->name));
+				brd->bd_flags |= BD_FEP5PLUS;
+			}
+
+			return;
+		}
+		msleep_interruptible(10);
+		brd->wait_for_fep++;
+		word = readw(addr + FEPSTAT);
+	}
+
+	/* Gave up on board after too long of time taken */
+	err1 = readw(addr + SEQUENCE);
+	err2 = readw(addr + ERROR);
+	APR(("***WARNING*** FEPOS for %s not functioning.  Error #(%x,%x).\n",
+		brd->name, err1, err2));
+	brd->state = BOARD_FAILED;
+	brd->dpastatus = BD_NOFEP;
+
+	DPR_INIT(("dgap_do_wait_for_fep() for board %s : finish\n", brd->name));
+}
+
+/*
+ * Physically forces the FEP5 card to reset itself.
+ */
+static void dgap_do_reset_board(struct board_t *brd)
+{
+	uchar check;
+	u32 check1;
+	u32 check2;
+	int i = 0;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase || !brd->re_map_port) {
+		DPR_INIT(("dgap_do_reset_board() start. bad values. brd: %p mem: %p io: %p\n", 
+			brd, brd ? brd->re_map_membase : 0, brd ? brd->re_map_port : 0));
+		return;
+	}
+
+	DPR_INIT(("dgap_do_reset_board() start. io: %p\n", brd->re_map_port));
+
+	/* FEPRST does not vary among supported boards */
+	writeb(FEPRST, brd->re_map_port);
+
+	for (i = 0; i <= 1000; i++) {
+		check = readb(brd->re_map_port) & 0xe;
+		if (check == FEPRST)
+			break;
+		udelay(10);
+
+	}
+	if (i > 1000) {
+		APR(("*** WARNING *** Board not resetting...  Failing board.\n"));
+		brd->state = BOARD_FAILED;
+		brd->dpastatus = BD_NOFEP;
+		goto failed;
+	}
+
+	/*
+	 * Make sure there really is memory out there.
+	 */
+	writel(0xa55a3cc3, (brd->re_map_membase + LOWMEM));
+	writel(0x5aa5c33c, (brd->re_map_membase + HIGHMEM));
+	check1 = readl(brd->re_map_membase + LOWMEM);
+	check2 = readl(brd->re_map_membase + HIGHMEM);
+
+	if ((check1 != 0xa55a3cc3) || (check2 != 0x5aa5c33c)) {
+		APR(("*** Warning *** No memory at %p for board.\n", brd->re_map_membase));
+		brd->state = BOARD_FAILED;
+		brd->dpastatus = BD_NOFEP;
+		goto failed;
+	}
+
+	if (brd->state != BOARD_FAILED)
+		brd->state = FINISHED_RESET;
+
+failed:
+	DPR_INIT(("dgap_do_reset_board() finish\n"));
+}
+
+#ifdef DIGI_CONCENTRATORS_SUPPORTED
+/*
+ * Sends a concentrator image into the FEP5 board.  FIXME: 
+ */
+void dgap_do_conc_load(struct board_t *brd, uchar *uaddr, int len)
+{
+	char *vaddr;
+	u16 offset = 0;
+	struct downld_t *to_dp;
+
+	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
+		return;
+
+	vaddr = brd->re_map_membase;
+
+	offset = readw((u16 *) (vaddr + DOWNREQ));
+	to_dp = (struct downld_t *) (vaddr + (int) offset);
+	memcpy_toio(to_dp, uaddr, len);
+
+	/* Tell card we have data for it */
+	writew(0, vaddr + (DOWNREQ));
+}
+#endif
+
+#define EXPANSION_ROM_SIZE	(64 * 1024)
+#define FEP5_ROM_MAGIC		(0xFEFFFFFF)
+
+static void dgap_get_vpd(struct board_t *brd)
+{
+	u32 magic;
+	u32 base_offset;
+	u16 rom_offset;
+	u16 vpd_offset;
+	u16 image_length;
+	u16 i;
+	uchar byte1;
+	uchar byte2;
+
+	/*
+	 * Poke the magic number at the PCI Rom Address location.
+	 * If VPD is supported, the value read from that address
+	 * will be non-zero.
+	 */
+	magic = FEP5_ROM_MAGIC;
+	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
+	pci_read_config_dword(brd->pdev, PCI_ROM_ADDRESS, &magic);
+
+	/* VPD not supported, bail */
+	if (!magic)
+		return;
+
+	/*
+	 * To get to the OTPROM memory, we have to send the boards base
+         * address or'ed with 1 into the PCI Rom Address location.
+	 */
+	magic = brd->membase | 0x01;
+	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
+	pci_read_config_dword(brd->pdev, PCI_ROM_ADDRESS, &magic);
+
+	byte1 = readb(brd->re_map_membase);
+	byte2 = readb(brd->re_map_membase + 1);
+
+	/*
+	 * If the board correctly swapped to the OTPROM memory,
+	 * the first 2 bytes (header) should be 0x55, 0xAA
+	 */
+	if (byte1 == 0x55 && byte2 == 0xAA) {
+
+		base_offset = 0;
+
+		/*
+		 * We have to run through all the OTPROM memory looking
+		 * for the VPD offset.
+		 */
+		while (base_offset <= EXPANSION_ROM_SIZE) {
+                
+			/*
+			 * Lots of magic numbers here.
+			 *
+			 * The VPD offset is located inside the ROM Data Structure.
+			 * We also have to remember the length of each
+			 * ROM Data Structure, so we can "hop" to the next
+			 * entry if the VPD isn't in the current
+			 * ROM Data Structure.
+			 */
+			rom_offset = readw(brd->re_map_membase + base_offset + 0x18);
+			image_length = readw(brd->re_map_membase + rom_offset + 0x10) * 512;
+			vpd_offset = readw(brd->re_map_membase + rom_offset + 0x08);
+
+			/* Found the VPD entry */
+			if (vpd_offset)
+				break;
+
+			/* We didn't find a VPD entry, go to next ROM entry. */
+			base_offset += image_length;
+
+			byte1 = readb(brd->re_map_membase + base_offset);
+			byte2 = readb(brd->re_map_membase + base_offset + 1);
+
+			/*
+			 * If the new ROM offset doesn't have 0x55, 0xAA
+			 * as its header, we have run out of ROM.
+			 */
+			if (byte1 != 0x55 || byte2 != 0xAA)
+				break;
+		}
+
+		/*
+		 * If we have a VPD offset, then mark the board
+		 * as having a valid VPD, and copy VPDSIZE (512) bytes of
+		 * that VPD to the buffer we have in our board structure.
+		 */
+		if (vpd_offset) {
+			brd->bd_flags |= BD_HAS_VPD;
+			for (i = 0; i < VPDSIZE; i++)
+				brd->vpd[i] = readb(brd->re_map_membase + vpd_offset + i);
+		}
+	}
+
+	/*
+	 * We MUST poke the magic number at the PCI Rom Address location again.
+	 * This makes the card report the regular board memory back to us,
+	 * rather than the OTPROM memory.
+	 */
+	magic = FEP5_ROM_MAGIC;
+	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
+}
+
+/*
+ * Our board poller function.
+ */
+void dgap_poll_tasklet(unsigned long data)
+{
+        struct board_t *bd = (struct board_t *) data;
+	ulong  lock_flags;
+	ulong  lock_flags2;
+	char *vaddr;
+	u16 head, tail;
+
+	if (!bd || (bd->magic != DGAP_BOARD_MAGIC)) {
+		APR(("dgap_poll_tasklet() - NULL or bad bd.\n"));
+		return;
+	}
+
+	if (bd->inhibit_poller)
+		return;
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+
+	vaddr = bd->re_map_membase;
+
+	/*
+	 * If board is ready, parse deeper to see if there is anything to do.
+	 */
+	if (bd->state == BOARD_READY) {
+
+		struct ev_t *eaddr = NULL;
+
+		if (!bd->re_map_membase) {
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			return;
+		}
+		if (!bd->re_map_port) {
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			return;
+		}
+
+		if (!bd->nasync) {
+			goto out;
+		}
+
+		eaddr = (struct ev_t *) (vaddr + EVBUF);
+
+		/* Get our head and tail */
+		head = readw(&(eaddr->ev_head));
+		tail = readw(&(eaddr->ev_tail));
+
+		/*
+		 * If there is an event pending. Go service it.
+		 */
+		if (head != tail) {
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			dgap_event(bd);
+			DGAP_LOCK(bd->bd_lock, lock_flags);
+		}
+
+out:
+		/*
+		 * If board is doing interrupts, ACK the interrupt.
+		 */
+		if (bd && bd->intr_running) {
+			readb(bd->re_map_port + 2);
+		}
+
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return;
+	}
+
+	/* Our state machine to get the board up and running */
+
+	/* Reset board */
+	if (bd->state == NEED_RESET) {
+
+		/* Get VPD info */
+		dgap_get_vpd(bd);
+
+		dgap_do_reset_board(bd);
+	}
+
+	/* Move to next state */
+	if (bd->state == FINISHED_RESET) {
+		bd->state = NEED_CONFIG;
+	}
+
+	if (bd->state == NEED_CONFIG) {
+		/*
+		 * Match this board to a config the user created for us.
+		 */
+		bd->bd_config = dgap_find_config(bd->type, bd->pci_bus, bd->pci_slot);
+
+		/*
+		 * Because the 4 port Xr products share the same PCI ID
+		 * as the 8 port Xr products, if we receive a NULL config
+		 * back, and this is a PAPORT8 board, retry with a
+		 * PAPORT4 attempt as well.
+		 */
+		if (bd->type == PAPORT8 && !bd->bd_config) {
+			bd->bd_config = dgap_find_config(PAPORT4, bd->pci_bus, bd->pci_slot);
+		}
+
+		/*
+		 * Register the ttys (if any) into the kernel.
+		 */
+		if (bd->bd_config) {
+			bd->state = FINISHED_CONFIG;
+		}
+		else {
+			bd->state = CONFIG_NOT_FOUND;
+		}
+	}
+
+	/* Move to next state */
+	if (bd->state == FINISHED_CONFIG) {
+		bd->state = NEED_DEVICE_CREATION;
+	}
+
+	/* Move to next state */
+	if (bd->state == NEED_DEVICE_CREATION) {
+		/*
+		 * Signal downloader, its got some work to do.
+		 */
+		DGAP_LOCK(dgap_dl_lock, lock_flags2);
+		if (dgap_dl_action != 1) {
+			dgap_dl_action = 1;
+			wake_up_interruptible(&dgap_dl_wait);
+		}
+		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
+	}
+
+	/* Move to next state */
+	if (bd->state == FINISHED_DEVICE_CREATION) {
+		bd->state = NEED_BIOS_LOAD;
+	}
+
+	/* Move to next state */
+	if (bd->state == NEED_BIOS_LOAD) {
+		/*
+		 * Signal downloader, its got some work to do.
+		 */
+		DGAP_LOCK(dgap_dl_lock, lock_flags2);
+		if (dgap_dl_action != 1) {
+			dgap_dl_action = 1;
+			wake_up_interruptible(&dgap_dl_wait);
+		}
+		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
+	}
+
+	/* Wait for BIOS to test board... */
+	if (bd->state == WAIT_BIOS_LOAD) {
+		dgap_do_wait_for_bios(bd);
+	}
+
+	/* Move to next state */
+	if (bd->state == FINISHED_BIOS_LOAD) {
+		bd->state = NEED_FEP_LOAD;
+
+		/*
+		 * Signal downloader, its got some work to do.
+		 */
+		DGAP_LOCK(dgap_dl_lock, lock_flags2);
+		if (dgap_dl_action != 1) {
+			dgap_dl_action = 1;
+			wake_up_interruptible(&dgap_dl_wait);
+		}
+		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
+	}
+
+	/* Wait for FEP to load on board... */
+	if (bd->state == WAIT_FEP_LOAD) {
+		dgap_do_wait_for_fep(bd);
+	}
+
+
+	/* Move to next state */
+	if (bd->state == FINISHED_FEP_LOAD) {
+
+		/*
+		 * Do tty device initialization.
+		 */
+		int rc = dgap_tty_init(bd);
+
+		if (rc < 0) {
+			dgap_tty_uninit(bd);
+			APR(("Can't init tty devices (%d)\n", rc));
+			bd->state = BOARD_FAILED;
+			bd->dpastatus = BD_NOFEP;
+		}
+		else {
+			bd->state = NEED_PROC_CREATION;
+
+			/*
+			 * Signal downloader, its got some work to do.
+			 */
+			DGAP_LOCK(dgap_dl_lock, lock_flags2);
+			if (dgap_dl_action != 1) {
+				dgap_dl_action = 1;
+				wake_up_interruptible(&dgap_dl_wait);
+			}
+			DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
+		}
+	}
+
+	/* Move to next state */
+	if (bd->state == FINISHED_PROC_CREATION) {
+
+		bd->state = BOARD_READY;
+		bd->dpastatus = BD_RUNNING;
+
+		/*
+		 * If user requested the board to run in interrupt mode,
+		 * go and set it up on the board.
+		 */
+		if (bd->intr_used) {
+			writew(1, (bd->re_map_membase + ENABLE_INTR));
+			/*
+			 * Tell the board to poll the UARTS as fast as possible.
+			 */
+			writew(FEPPOLL_MIN, (bd->re_map_membase + FEPPOLL));
+			bd->intr_running = 1;
+		}
+
+		/* Wake up anyone waiting for board state to change to ready */
+		wake_up_interruptible(&bd->state_wait);
+	}
+
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+}
+
+/*=======================================================================
+ *
+ *      dgap_cmdb - Sends a 2 byte command to the FEP.
+ *
+ *              ch      - Pointer to channel structure.
+ *              cmd     - Command to be sent.
+ *              byte1   - Integer containing first byte to be sent.
+ *              byte2   - Integer containing second byte to be sent.
+ *              ncmds   - Wait until ncmds or fewer cmds are left
+ *                        in the cmd buffer before returning.
+ *
+ *=======================================================================*/
+void dgap_cmdb(struct channel_t *ch, uchar cmd, uchar byte1, uchar byte2, uint ncmds)
+{                       
+	char		*vaddr = NULL;
+	struct cm_t	*cm_addr = NULL;
+	uint		count;
+	uint		n;
+	u16		head;
+        u16		tail;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	/*
+	 * Check if board is still alive.
+	 */
+	if (ch->ch_bd->state == BOARD_FAILED) {
+		DPR_CORE(("%s:%d board is in failed state.\n", __FILE__, __LINE__));
+		return;
+        }               
+
+	/*
+	 * Make sure the pointers are in range before
+	 * writing to the FEP memory.
+	 */
+	vaddr = ch->ch_bd->re_map_membase;
+
+	if (!vaddr)
+		return;
+
+	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
+	head = readw(&(cm_addr->cm_head));
+
+	/* 
+	 * Forget it if pointers out of range.
+	 */
+	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
+		DPR_CORE(("%s:%d pointers out of range, failing board!\n", __FILE__, __LINE__));
+		ch->ch_bd->state = BOARD_FAILED;
+		return; 
+	}
+
+	/*
+	 * Put the data in the circular command buffer.
+	 */
+	writeb(cmd, (char *) (vaddr + head + CMDSTART + 0));
+	writeb((uchar) ch->ch_portnum, (char *) (vaddr + head + CMDSTART + 1));
+	writeb(byte1, (char *) (vaddr + head + CMDSTART + 2));
+	writeb(byte2, (char *) (vaddr + head + CMDSTART + 3));
+
+	head = (head + 4) & (CMDMAX - CMDSTART - 4);
+
+	writew(head, &(cm_addr->cm_head));
+
+	/*
+	 * Wait if necessary before updating the head  
+	 * pointer to limit the number of outstanding
+	 * commands to the FEP.   If the time spent waiting
+	 * is outlandish, declare the FEP dead.
+	 */
+	for (count = dgap_count ;;) {
+
+		head = readw(&(cm_addr->cm_head));
+		tail = readw(&(cm_addr->cm_tail));
+
+		n = (head - tail) & (CMDMAX - CMDSTART - 4);
+
+		if (n <= ncmds * sizeof(struct cm_t))
+			break;
+
+		if (--count == 0) {
+			DPR_CORE(("%s:%d failing board.\n",__FILE__, __LINE__));
+			ch->ch_bd->state = BOARD_FAILED;
+			return;
+		}
+		udelay(10);
+	}  
+}
+
+/*=======================================================================
+ *
+ *      dgap_cmdw - Sends a 1 word command to the FEP.
+ *      
+ *              ch      - Pointer to channel structure.
+ *              cmd     - Command to be sent.
+ *              word    - Integer containing word to be sent.
+ *              ncmds   - Wait until ncmds or fewer cmds are left
+ *                        in the cmd buffer before returning.
+ *
+ *=======================================================================*/
+void dgap_cmdw(struct channel_t *ch, uchar cmd, u16 word, uint ncmds)
+{
+	char		*vaddr = NULL;
+	struct cm_t	*cm_addr = NULL;
+	uint		count;
+	uint		n;
+	u16		head;
+	u16		tail;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	/*
+	 * Check if board is still alive.
+	 */
+	if (ch->ch_bd->state == BOARD_FAILED) {
+		DPR_CORE(("%s:%d board is failed!\n", __FILE__, __LINE__));
+		return;
+	}
+
+	/*
+	 * Make sure the pointers are in range before
+	 * writing to the FEP memory.
+	 */
+	vaddr = ch->ch_bd->re_map_membase;
+	if (!vaddr)
+		return;
+
+	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
+	head = readw(&(cm_addr->cm_head));
+
+	/* 
+	 * Forget it if pointers out of range.
+	 */
+	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
+		DPR_CORE(("%s:%d Pointers out of range.  Failing board.\n",__FILE__, __LINE__));
+		ch->ch_bd->state = BOARD_FAILED;
+		return;
+	}
+
+	/*
+	 * Put the data in the circular command buffer.
+	 */
+	writeb(cmd, (char *) (vaddr + head + CMDSTART + 0));
+	writeb((uchar) ch->ch_portnum, (char *) (vaddr + head + CMDSTART + 1));
+	writew((u16) word, (char *) (vaddr + head + CMDSTART + 2));
+
+	head = (head + 4) & (CMDMAX - CMDSTART - 4);
+
+	writew(head, &(cm_addr->cm_head));
+
+	/*
+	 * Wait if necessary before updating the head
+	 * pointer to limit the number of outstanding  
+	 * commands to the FEP.   If the time spent waiting
+	 * is outlandish, declare the FEP dead.
+	 */
+	for (count = dgap_count ;;) {
+
+		head = readw(&(cm_addr->cm_head));
+		tail = readw(&(cm_addr->cm_tail));
+
+		n = (head - tail) & (CMDMAX - CMDSTART - 4);
+
+		if (n <= ncmds * sizeof(struct cm_t))
+			break;
+
+		if (--count == 0) {
+			DPR_CORE(("%s:%d Failing board.\n",__FILE__, __LINE__));
+			ch->ch_bd->state = BOARD_FAILED;
+			return;
+		}
+		udelay(10);
+	}  
+}
+
+/*=======================================================================
+ *
+ *      dgap_cmdw_ext - Sends a extended word command to the FEP.
+ *      
+ *              ch      - Pointer to channel structure.
+ *              cmd     - Command to be sent.
+ *              word    - Integer containing word to be sent.
+ *              ncmds   - Wait until ncmds or fewer cmds are left
+ *                        in the cmd buffer before returning.
+ *
+ *=======================================================================*/
+static void dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds)
+{
+	char		*vaddr = NULL;
+	struct cm_t	*cm_addr = NULL;
+	uint		count;
+	uint		n;
+	u16		head;
+	u16		tail;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	/*
+	 * Check if board is still alive.
+	 */
+	if (ch->ch_bd->state == BOARD_FAILED) {
+		DPR_CORE(("%s:%d board is failed!\n", __FILE__, __LINE__));
+		return;
+	}
+
+	/*
+	 * Make sure the pointers are in range before
+	 * writing to the FEP memory.
+	 */
+	vaddr = ch->ch_bd->re_map_membase;
+	if (!vaddr)
+		return;
+
+	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
+	head = readw(&(cm_addr->cm_head));
+
+	/* 
+	 * Forget it if pointers out of range.
+	 */
+	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
+		DPR_CORE(("%s:%d Pointers out of range.  Failing board.\n",__FILE__, __LINE__));
+		ch->ch_bd->state = BOARD_FAILED;
+		return;
+	}
+
+	/*
+	 * Put the data in the circular command buffer.
+	 */
+
+	/* Write an FF to tell the FEP that we want an extended command */
+	writeb((uchar) 0xff, (char *) (vaddr + head + CMDSTART + 0));
+
+	writeb((uchar) ch->ch_portnum, (uchar *) (vaddr + head + CMDSTART + 1));
+	writew((u16) cmd, (char *) (vaddr + head + CMDSTART + 2));
+
+	/*
+	 * If the second part of the command won't fit,
+	 * put it at the beginning of the circular buffer.
+	 */
+	if (((head + 4) >= ((CMDMAX - CMDSTART)) || (head & 03))) {
+		writew((u16) word, (char *) (vaddr + CMDSTART));
+	} else {
+		writew((u16) word, (char *) (vaddr + head + CMDSTART + 4));
+	}
+
+	head = (head + 8) & (CMDMAX - CMDSTART - 4);
+
+	writew(head, &(cm_addr->cm_head));
+
+	/*
+	 * Wait if necessary before updating the head
+	 * pointer to limit the number of outstanding  
+	 * commands to the FEP.   If the time spent waiting
+	 * is outlandish, declare the FEP dead.
+	 */
+	for (count = dgap_count ;;) {
+
+		head = readw(&(cm_addr->cm_head));
+		tail = readw(&(cm_addr->cm_tail));
+
+		n = (head - tail) & (CMDMAX - CMDSTART - 4);
+
+		if (n <= ncmds * sizeof(struct cm_t))
+			break;
+
+		if (--count == 0) {
+			DPR_CORE(("%s:%d Failing board.\n",__FILE__, __LINE__));
+			ch->ch_bd->state = BOARD_FAILED;
+			return;
+		}
+		udelay(10);
+	}  
+}
+
+/*=======================================================================
+ *
+ *      dgap_wmove - Write data to FEP buffer.
+ *
+ *              ch      - Pointer to channel structure.
+ *              buf     - Poiter to characters to be moved.
+ *              cnt     - Number of characters to move.
+ *
+ *=======================================================================*/
+void dgap_wmove(struct channel_t *ch, char *buf, uint cnt)
+{
+	int    n;
+	char   *taddr;
+	struct bs_t    *bs;
+	u16    head;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+ 
+	/*
+	 * Check parameters.
+	 */
+	bs   = ch->ch_bs;
+	head = readw(&(bs->tx_head));
+
+	/*
+	 * If pointers are out of range, just return.
+	 */
+	if ((cnt > ch->ch_tsize) || (unsigned)(head - ch->ch_tstart) >= ch->ch_tsize) {
+		DPR_CORE(("%s:%d pointer out of range", __FILE__, __LINE__));
+		return;
+	}
+
+	/*
+	 * If the write wraps over the top of the circular buffer,
+	 * move the portion up to the wrap point, and reset the
+	 * pointers to the bottom.
+	 */
+	n = ch->ch_tstart + ch->ch_tsize - head;
+
+	if (cnt >= n) {
+		cnt -= n;
+		taddr = ch->ch_taddr + head;
+		memcpy_toio(taddr, buf, n);
+		head = ch->ch_tstart;
+		buf += n;
+	}
+
+	/*
+	 * Move rest of data.
+	 */
+	taddr = ch->ch_taddr + head;
+	n = cnt;
+	memcpy_toio(taddr, buf, n);
+	head += cnt;
+
+	writew(head, &(bs->tx_head));
+}
+
+/*
+ * Retrives the current custom baud rate from FEP memory,
+ * and returns it back to the user.
+ * Returns 0 on error.
+ */
+uint dgap_get_custom_baud(struct channel_t *ch)
+{
+	uchar *vaddr;
+	ulong offset = 0;
+	uint value = 0;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC) {
+		return 0;
+	}
+
+	if (!ch->ch_bd || ch->ch_bd->magic != DGAP_BOARD_MAGIC) {
+		return 0;
+	}
+
+	if (!(ch->ch_bd->bd_flags & BD_FEP5PLUS))
+		return 0;
+
+	vaddr = ch->ch_bd->re_map_membase;
+
+	if (!vaddr)
+		return 0;
+
+	/*
+	 * Go get from fep mem, what the fep
+	 * believes the custom baud rate is. 
+	 */
+	offset = ((((*(unsigned short *)(vaddr + ECS_SEG)) << 4) +  
+		(ch->ch_portnum * 0x28) + LINE_SPEED));
+
+	value = readw(vaddr + offset);
+	return value;
+}
+
+/*
+ * Calls the firmware to reset this channel.
+ */
+void dgap_firmware_reset_port(struct channel_t *ch)
+{
+	dgap_cmdb(ch, CHRESET, 0, 0, 0);
+
+	/*
+	 * Now that the channel is reset, we need to make sure
+	 * all the current settings get reapplied to the port
+	 * in the firmware.
+	 *
+	 * So we will set the driver's cache of firmware
+	 * settings all to 0, and then call param.
+	 */
+	ch->ch_fepiflag = 0;
+	ch->ch_fepcflag = 0;
+	ch->ch_fepoflag = 0;
+	ch->ch_fepstartc = 0;
+	ch->ch_fepstopc = 0;
+	ch->ch_fepastartc = 0;
+	ch->ch_fepastopc = 0;
+	ch->ch_mostat = 0;
+	ch->ch_hflow = 0;
+}
+
+/*=======================================================================
+ *      
+ *      dgap_param - Set Digi parameters.
+ *
+ *              struct tty_struct *     - TTY for port.
+ *
+ *=======================================================================*/
+int dgap_param(struct tty_struct *tty)
+{
+	struct ktermios *ts;
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct bs_t   *bs;
+	struct un_t   *un;
+	u16	head;
+	u16	cflag;
+	u16	iflag;
+	uchar	mval;
+	uchar	hflow;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return -ENXIO;
+
+	un = (struct un_t *) tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return -ENXIO;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return -ENXIO;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return -ENXIO;
+
+        bs = ch->ch_bs;
+	if (!bs)
+		return -ENXIO;
+
+	DPR_PARAM(("param start: tdev: %x cflags: %x oflags: %x iflags: %x\n",
+		ch->ch_tun.un_dev, ch->ch_c_cflag, ch->ch_c_oflag, ch->ch_c_iflag));
+
+	ts = &tty->termios;
+
+	/*
+	 * If baud rate is zero, flush queues, and set mval to drop DTR.
+	 */
+	if ((ch->ch_c_cflag & (CBAUD)) == 0) {
+
+		/* flush rx */
+		head = readw(&(ch->ch_bs->rx_head));
+		writew(head, &(ch->ch_bs->rx_tail));
+
+		/* flush tx */
+		head = readw(&(ch->ch_bs->tx_head));
+		writew(head, &(ch->ch_bs->tx_tail));
+
+		ch->ch_flags |= (CH_BAUD0);
+
+		/* Drop RTS and DTR */
+		ch->ch_mval &= ~(D_RTS(ch)|D_DTR(ch));
+		mval = D_DTR(ch) | D_RTS(ch);
+		ch->ch_baud_info = 0;
+
+	} else if (ch->ch_custom_speed && (bd->bd_flags & BD_FEP5PLUS)) {
+		/*
+		 * Tell the fep to do the command
+		 */
+
+		DPR_PARAM(("param: Want %d speed\n", ch->ch_custom_speed));
+
+		dgap_cmdw_ext(ch, 0xff01, ch->ch_custom_speed, 0);
+
+		/*
+		 * Now go get from fep mem, what the fep
+		 * believes the custom baud rate is. 
+		 */
+		ch->ch_baud_info = ch->ch_custom_speed = dgap_get_custom_baud(ch);
+
+		DPR_PARAM(("param: Got %d speed\n", ch->ch_custom_speed));
+
+		/* Handle transition from B0 */   
+		if (ch->ch_flags & CH_BAUD0) {
+			ch->ch_flags &= ~(CH_BAUD0);
+			ch->ch_mval |= (D_RTS(ch)|D_DTR(ch));
+		}
+		mval = D_DTR(ch) | D_RTS(ch);
+
+	} else {
+		/*
+		 * Set baud rate, character size, and parity.
+		 */
+
+
+		int iindex = 0;
+		int jindex = 0;
+		int baud = 0;
+
+		ulong bauds[4][16] = {
+			{ /* slowbaud */
+				0,	50,	75,	110,
+				134,	150,	200,	300,
+				600,	1200,	1800,	2400,
+				4800,	9600,	19200,	38400 },
+			{ /* slowbaud & CBAUDEX */
+				0,	57600,	115200,	230400,
+				460800,	150,	200,	921600,
+				600,	1200,	1800,	2400,
+				4800,	9600,	19200,	38400 },
+			{ /* fastbaud */
+				0,	57600,	76800,	115200,
+				14400,	57600,	230400,	76800,
+				115200,	230400,	28800,	460800,
+				921600,	9600,	19200,	38400 },
+			{ /* fastbaud & CBAUDEX */
+				0,	57600,	115200,	230400,
+				460800,	150,	200,	921600,
+				600,	1200,	1800,	2400,
+				4800,	9600,	19200,	38400 }
+		};
+
+		/* Only use the TXPrint baud rate if the terminal unit is NOT open */
+		if (!(ch->ch_tun.un_flags & UN_ISOPEN) && (un->un_type == DGAP_PRINT))
+			baud = C_BAUD(ch->ch_pun.un_tty) & 0xff;
+		else
+			baud = C_BAUD(ch->ch_tun.un_tty) & 0xff;
+
+		if (ch->ch_c_cflag & CBAUDEX)
+			iindex = 1;
+
+		if (ch->ch_digi.digi_flags & DIGI_FAST)
+			iindex += 2;
+
+		jindex = baud;
+
+		if ((iindex >= 0) && (iindex < 4) && (jindex >= 0) && (jindex < 16)) {
+			baud = bauds[iindex][jindex];
+		} else {
+			DPR_IOCTL(("baud indices were out of range (%d)(%d)",
+				iindex, jindex));
+			baud = 0;
+		}
+
+		if (baud == 0)  
+			baud = 9600;
+
+		ch->ch_baud_info = baud;
+
+
+		/*
+		 * CBAUD has bit position 0x1000 set these days to indicate Linux
+		 * baud rate remap.
+		 * We use a different bit assignment for high speed.  Clear this
+		 * bit out while grabbing the parts of "cflag" we want.
+		 */
+		cflag = ch->ch_c_cflag & ((CBAUD ^ CBAUDEX) | PARODD | PARENB | CSTOPB | CSIZE);
+
+		/*
+		 * HUPCL bit is used by FEP to indicate fast baud
+		 * table is to be used.
+		 */
+		if ((ch->ch_digi.digi_flags & DIGI_FAST) || (ch->ch_c_cflag & CBAUDEX))
+			cflag |= HUPCL;
+
+
+		if ((ch->ch_c_cflag & CBAUDEX) && !(ch->ch_digi.digi_flags & DIGI_FAST)) {
+		/*
+		 * The below code is trying to guarantee that only baud rates
+		 * 115200, 230400, 460800, 921600 are remapped.  We use exclusive or
+		 * because the various baud rates share common bit positions
+		 * and therefore can't be tested for easily.
+		 */
+			tcflag_t tcflag = (ch->ch_c_cflag & CBAUD) | CBAUDEX;
+			int baudpart = 0;
+
+			/* Map high speed requests to index into FEP's baud table */
+			switch (tcflag) {
+			case B57600 :
+				baudpart = 1;
+				break;
+#ifdef B76800
+			case B76800 :
+				baudpart = 2;
+				break;
+#endif
+			case B115200 :
+				baudpart = 3;
+				break;
+			case B230400 :
+				baudpart = 9;
+				break;
+			case B460800 :
+				baudpart = 11;
+				break;
+#ifdef B921600
+			case B921600 :
+				baudpart = 12;
+				break;
+#endif
+			default:
+				baudpart = 0;
+			}
+
+			if (baudpart)
+				cflag = (cflag & ~(CBAUD | CBAUDEX)) | baudpart;
+		}
+
+		cflag &= 0xffff;
+
+		if (cflag != ch->ch_fepcflag) {
+			ch->ch_fepcflag = (u16) (cflag & 0xffff);
+
+			/* Okay to have channel and board locks held calling this */
+			dgap_cmdw(ch, SCFLAG, (u16) cflag, 0);
+		}
+
+		/* Handle transition from B0 */   
+		if (ch->ch_flags & CH_BAUD0) {
+			ch->ch_flags &= ~(CH_BAUD0);
+			ch->ch_mval |= (D_RTS(ch)|D_DTR(ch));
+		}
+		mval = D_DTR(ch) | D_RTS(ch);
+	}
+
+	/*
+	 * Get input flags.
+	 */
+	iflag = ch->ch_c_iflag & (IGNBRK | BRKINT | IGNPAR | PARMRK | INPCK | ISTRIP | IXON | IXANY | IXOFF);
+
+	if ((ch->ch_startc == _POSIX_VDISABLE) || (ch->ch_stopc == _POSIX_VDISABLE)) {
+		iflag &= ~(IXON | IXOFF);
+		ch->ch_c_iflag &= ~(IXON | IXOFF);
+	}
+
+	/*
+	 * Only the IBM Xr card can switch between
+	 * 232 and 422 modes on the fly
+	 */
+	if (bd->device == PCI_DEVICE_XR_IBM_DID) {
+		if (ch->ch_digi.digi_flags & DIGI_422)
+			dgap_cmdb(ch, SCOMMODE, MODE_422, 0, 0);
+		else
+			dgap_cmdb(ch, SCOMMODE, MODE_232, 0, 0);
+	}
+
+	if (ch->ch_digi.digi_flags & DIGI_ALTPIN)
+		iflag |= IALTPIN ;
+
+	if (iflag != ch->ch_fepiflag) {
+		ch->ch_fepiflag = iflag;
+
+		/* Okay to have channel and board locks held calling this */
+		dgap_cmdw(ch, SIFLAG, (u16) ch->ch_fepiflag, 0);
+	}
+
+	/*
+	 * Select hardware handshaking.
+	 */
+	hflow = 0;
+
+	if (ch->ch_c_cflag & CRTSCTS) {
+		hflow |= (D_RTS(ch) | D_CTS(ch));
+	}
+	if (ch->ch_digi.digi_flags & RTSPACE)
+		hflow |= D_RTS(ch);
+	if (ch->ch_digi.digi_flags & DTRPACE)
+		hflow |= D_DTR(ch);  
+	if (ch->ch_digi.digi_flags & CTSPACE)
+		hflow |= D_CTS(ch);
+	if (ch->ch_digi.digi_flags & DSRPACE)
+		hflow |= D_DSR(ch);
+	if (ch->ch_digi.digi_flags & DCDPACE)
+		hflow |= D_CD(ch);
+
+	if (hflow != ch->ch_hflow) {
+		ch->ch_hflow = hflow;
+
+		/* Okay to have channel and board locks held calling this */
+		dgap_cmdb(ch, SHFLOW, (uchar) hflow, 0xff, 0);
+        }
+
+
+	/*
+	 * Set RTS and/or DTR Toggle if needed, but only if product is FEP5+ based.
+	 */
+	if (bd->bd_flags & BD_FEP5PLUS) {
+		u16 hflow2 = 0;
+		if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) {
+			hflow2 |= (D_RTS(ch));
+		}
+		if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) {
+			hflow2 |= (D_DTR(ch));
+		}
+
+		dgap_cmdw_ext(ch, 0xff03, hflow2, 0);
+	}
+
+	/*
+	 * Set modem control lines.  
+	 */
+
+	mval ^= ch->ch_mforce & (mval ^ ch->ch_mval);
+
+	DPR_PARAM(("dgap_param: mval: %x ch_mforce: %x ch_mval: %x ch_mostat: %x\n",
+		mval, ch->ch_mforce, ch->ch_mval, ch->ch_mostat));
+
+	if (ch->ch_mostat ^ mval) {
+		ch->ch_mostat = mval;
+
+		/* Okay to have channel and board locks held calling this */
+		DPR_PARAM(("dgap_param: Sending SMODEM mval: %x\n", mval));
+		dgap_cmdb(ch, SMODEM, (uchar) mval, D_RTS(ch)|D_DTR(ch), 0);
+	}
+
+	/*
+	 * Read modem signals, and then call carrier function.             
+	 */
+	ch->ch_mistat = readb(&(bs->m_stat));
+	dgap_carrier(ch);
+
+	/*      
+	 * Set the start and stop characters.
+	 */
+	if (ch->ch_startc != ch->ch_fepstartc || ch->ch_stopc != ch->ch_fepstopc) {
+		ch->ch_fepstartc = ch->ch_startc;
+		ch->ch_fepstopc =  ch->ch_stopc;
+
+		/* Okay to have channel and board locks held calling this */
+		dgap_cmdb(ch, SFLOWC, ch->ch_fepstartc, ch->ch_fepstopc, 0);
+	}
+
+	/*
+	 * Set the Auxiliary start and stop characters.
+	 */     
+	if (ch->ch_astartc != ch->ch_fepastartc || ch->ch_astopc != ch->ch_fepastopc) {
+		ch->ch_fepastartc = ch->ch_astartc;
+		ch->ch_fepastopc = ch->ch_astopc;
+
+		/* Okay to have channel and board locks held calling this */
+		dgap_cmdb(ch, SAFLOWC, ch->ch_fepastartc, ch->ch_fepastopc, 0);
+	}
+
+	DPR_PARAM(("param finish\n"));
+
+	return 0;
+}
+
+/*
+ * dgap_parity_scan()
+ *
+ * Convert the FEP5 way of reporting parity errors and breaks into
+ * the Linux line discipline way.
+ */
+void dgap_parity_scan(struct channel_t *ch, unsigned char *cbuf, unsigned char *fbuf, int *len)
+{
+	int l = *len;
+	int count = 0;
+	unsigned char *in, *cout, *fout;
+	unsigned char c;
+
+	in = cbuf;
+	cout = cbuf;
+	fout = fbuf;
+
+	DPR_PSCAN(("dgap_parity_scan start\n"));
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	while (l--) {
+		c = *in++;
+		switch (ch->pscan_state) {
+		default:
+			/* reset to sanity and fall through */
+			ch->pscan_state = 0;
+
+		case 0:
+			/* No FF seen yet */
+			if (c == (unsigned char) '\377') {
+				/* delete this character from stream */
+				ch->pscan_state = 1;
+			} else {
+				*cout++ = c;
+				*fout++ = TTY_NORMAL;
+				count += 1;
+			}
+			break;
+
+		case 1:
+			/* first FF seen */
+			if (c == (unsigned char) '\377') {
+				/* doubled ff, transform to single ff */
+				*cout++ = c;
+				*fout++ = TTY_NORMAL;
+				count += 1;
+				ch->pscan_state = 0;
+			} else {
+				/* save value examination in next state */
+				ch->pscan_savechar = c;
+				ch->pscan_state = 2; 
+			}
+			break;
+
+		case 2:
+			/* third character of ff sequence */
+
+			*cout++ = c;
+
+			if (ch->pscan_savechar == 0x0) {
+
+				if (c == 0x0) {
+					DPR_PSCAN(("dgap_parity_scan in 3rd char of ff seq. c: %x setting break.\n", c));
+					ch->ch_err_break++;
+					*fout++ = TTY_BREAK;
+				}
+				else {
+					DPR_PSCAN(("dgap_parity_scan in 3rd char of ff seq. c: %x setting parity.\n", c));
+					ch->ch_err_parity++;
+					*fout++ = TTY_PARITY;
+				}
+			}
+			else {
+				DPR_PSCAN(("%s:%d Logic Error.\n", __FILE__, __LINE__));
+			}
+
+			count += 1;
+			ch->pscan_state = 0;
+		}       
+	}
+	*len = count;
+	DPR_PSCAN(("dgap_parity_scan finish\n"));
+}
+
+/*=======================================================================
+ *
+ *      dgap_event - FEP to host event processing routine.
+ *
+ *              bd     - Board of current event.
+ *
+ *=======================================================================*/
+static int dgap_event(struct board_t *bd)
+{
+	struct channel_t *ch;
+	ulong		lock_flags;
+	ulong		lock_flags2;
+	struct bs_t	*bs;
+	uchar		*event;
+	uchar		*vaddr = NULL;
+	struct ev_t	*eaddr = NULL;
+	uint		head;
+	uint		tail;
+	int		port;
+	int		reason;
+	int		modem;
+	int		b1;
+
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return -ENXIO;
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+
+	vaddr = bd->re_map_membase;
+
+	if (!vaddr) {
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return -ENXIO;
+	}
+
+	eaddr = (struct ev_t *) (vaddr + EVBUF);
+
+	/* Get our head and tail */
+	head = readw(&(eaddr->ev_head));
+	tail = readw(&(eaddr->ev_tail));
+
+	/*
+	 * Forget it if pointers out of range.
+	 */
+
+	if (head >= EVMAX - EVSTART || tail >= EVMAX - EVSTART ||
+	    (head | tail) & 03) {
+		DPR_EVENT(("should be calling xxfail %d\n", __LINE__));
+		/* Let go of board lock */
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return -ENXIO;
+	}
+
+	/*
+	 * Loop to process all the events in the buffer.
+	 */
+	while (tail != head) {
+
+		/*
+		 * Get interrupt information.
+		 */
+
+		event = bd->re_map_membase + tail + EVSTART;
+
+		port   = event[0];
+		reason = event[1];
+		modem  = event[2];
+		b1     = event[3];
+
+		DPR_EVENT(("event: jiffies: %ld port: %d reason: %x modem: %x\n",
+			jiffies, port, reason, modem));
+
+		/*
+		 * Make sure the interrupt is valid.
+		 */
+                if (port >= bd->nasync) 
+			goto next;
+
+		if (!(reason & (IFMODEM | IFBREAK | IFTLW | IFTEM | IFDATA))) 
+			goto next;
+
+		ch = bd->channels[port];
+
+		if (!ch || ch->magic != DGAP_CHANNEL_MAGIC) 
+			goto next;
+
+		/*
+		 * If we have made it here, the event was valid.
+		 * Lock down the channel.
+		 */
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+		bs = ch->ch_bs;
+
+		if (!bs) {
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			goto next;
+		}
+
+		/*
+		 * Process received data.
+		 */
+		if (reason & IFDATA) {
+
+			/*
+			 * ALL LOCKS *MUST* BE DROPPED BEFORE CALLING INPUT!
+			 * input could send some data to ld, which in turn
+			 * could do a callback to one of our other functions.
+			 */
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+			dgap_input(ch);
+
+			DGAP_LOCK(bd->bd_lock, lock_flags);
+			DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+			if (ch->ch_flags & CH_RACTIVE)
+				ch->ch_flags |= CH_RENABLE;
+			else
+				writeb(1, &(bs->idata));
+
+			if (ch->ch_flags & CH_RWAIT) {
+				ch->ch_flags &= ~CH_RWAIT;
+
+				wake_up_interruptible(&ch->ch_tun.un_flags_wait);
+			}
+		}
+
+		/*
+		 * Process Modem change signals. 
+		 */
+		if (reason & IFMODEM) {
+			ch->ch_mistat = modem;
+			dgap_carrier(ch);
+		}
+
+		/*
+		 * Process break.
+		 */
+		if (reason & IFBREAK) {
+
+			DPR_EVENT(("got IFBREAK\n"));
+
+			if (ch->ch_tun.un_tty) {
+				/* A break has been indicated */
+				ch->ch_err_break++;
+				tty_buffer_request_room(ch->ch_tun.un_tty->port, 1);
+				tty_insert_flip_char(ch->ch_tun.un_tty->port, 0, TTY_BREAK);
+				tty_flip_buffer_push(ch->ch_tun.un_tty->port);
+			}
+		}
+
+		/*
+		 * Process Transmit low.
+		 */
+		if (reason & IFTLW) {
+
+			DPR_EVENT(("event: got low event\n"));
+
+			if (ch->ch_tun.un_flags & UN_LOW) {
+				ch->ch_tun.un_flags &= ~UN_LOW;
+
+				if (ch->ch_tun.un_flags & UN_ISOPEN) {
+					if ((ch->ch_tun.un_tty->flags & 
+					   (1 << TTY_DO_WRITE_WAKEUP)) &&
+						ch->ch_tun.un_tty->ldisc->ops->write_wakeup)
+					{
+						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+						DGAP_UNLOCK(bd->bd_lock, lock_flags);
+						(ch->ch_tun.un_tty->ldisc->ops->write_wakeup)(ch->ch_tun.un_tty);
+						DGAP_LOCK(bd->bd_lock, lock_flags);
+						DGAP_LOCK(ch->ch_lock, lock_flags2);
+					}
+					wake_up_interruptible(&ch->ch_tun.un_tty->write_wait);
+					wake_up_interruptible(&ch->ch_tun.un_flags_wait);
+
+					DPR_EVENT(("event: Got low event. jiffies: %lu\n", jiffies));
+				}
+			}
+
+			if (ch->ch_pun.un_flags & UN_LOW) {
+				ch->ch_pun.un_flags &= ~UN_LOW;
+				if (ch->ch_pun.un_flags & UN_ISOPEN) {
+					if ((ch->ch_pun.un_tty->flags & 
+					   (1 << TTY_DO_WRITE_WAKEUP)) &&
+						ch->ch_pun.un_tty->ldisc->ops->write_wakeup)
+					{
+						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+						DGAP_UNLOCK(bd->bd_lock, lock_flags);
+						(ch->ch_pun.un_tty->ldisc->ops->write_wakeup)(ch->ch_pun.un_tty);
+						DGAP_LOCK(bd->bd_lock, lock_flags);
+						DGAP_LOCK(ch->ch_lock, lock_flags2);
+					}
+					wake_up_interruptible(&ch->ch_pun.un_tty->write_wait);
+					wake_up_interruptible(&ch->ch_pun.un_flags_wait);
+				}
+			}
+
+			if (ch->ch_flags & CH_WLOW) {
+				ch->ch_flags &= ~CH_WLOW;
+				wake_up_interruptible(&ch->ch_flags_wait);
+			}
+		}
+
+		/*
+		 * Process Transmit empty.
+		 */
+		if (reason & IFTEM) {
+			DPR_EVENT(("event: got empty event\n"));
+
+			if (ch->ch_tun.un_flags & UN_EMPTY) {
+				ch->ch_tun.un_flags &= ~UN_EMPTY;
+				if (ch->ch_tun.un_flags & UN_ISOPEN) {
+					if ((ch->ch_tun.un_tty->flags & 
+					   (1 << TTY_DO_WRITE_WAKEUP)) &&
+						ch->ch_tun.un_tty->ldisc->ops->write_wakeup)
+					{
+						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+						DGAP_UNLOCK(bd->bd_lock, lock_flags);
+						(ch->ch_tun.un_tty->ldisc->ops->write_wakeup)(ch->ch_tun.un_tty);
+						DGAP_LOCK(bd->bd_lock, lock_flags);
+						DGAP_LOCK(ch->ch_lock, lock_flags2);
+					}
+					wake_up_interruptible(&ch->ch_tun.un_tty->write_wait);
+					wake_up_interruptible(&ch->ch_tun.un_flags_wait);
+				}
+			}
+
+			if (ch->ch_pun.un_flags & UN_EMPTY) {
+				ch->ch_pun.un_flags &= ~UN_EMPTY;
+				if (ch->ch_pun.un_flags & UN_ISOPEN) {
+					if ((ch->ch_pun.un_tty->flags & 
+					   (1 << TTY_DO_WRITE_WAKEUP)) &&
+						ch->ch_pun.un_tty->ldisc->ops->write_wakeup)
+					{
+						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+						DGAP_UNLOCK(bd->bd_lock, lock_flags);
+						(ch->ch_pun.un_tty->ldisc->ops->write_wakeup)(ch->ch_pun.un_tty);
+						DGAP_LOCK(bd->bd_lock, lock_flags);
+						DGAP_LOCK(ch->ch_lock, lock_flags2);
+					}
+					wake_up_interruptible(&ch->ch_pun.un_tty->write_wait);
+					wake_up_interruptible(&ch->ch_pun.un_flags_wait);
+				}
+			}
+
+
+			if (ch->ch_flags & CH_WEMPTY) {
+				ch->ch_flags &= ~CH_WEMPTY;
+				wake_up_interruptible(&ch->ch_flags_wait);
+			}
+		}
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+
+next:
+		tail = (tail + 4) & (EVMAX - EVSTART - 4);
+	}
+
+	writew(tail, &(eaddr->ev_tail));
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	return 0;
+}               
+
+/*
+ * Parse a configuration file read into memory as a string.
+ */
+int	dgap_parsefile(char **in, int Remove)
+{
+	struct cnode *p, *brd, *line, *conc;
+	int	rc;
+	char	*s = NULL, *s2 = NULL;
+	int	linecnt = 0;
+
+	p = &dgap_head;
+	brd = line = conc = NULL;
+
+	/* perhaps we are adding to an existing list? */
+	while (p->next != NULL) {
+		p = p->next;
+	}
+
+	/* file must start with a BEGIN */
+	while ( (rc = dgap_gettok(in,p)) != BEGIN ) {
+		if (rc == 0) {
+			dgap_err("unexpected EOF");
+			return(-1);
+		}
+	}
+
+	for (; ; ) {
+		rc = dgap_gettok(in,p);
+		if (rc == 0) {
+			dgap_err("unexpected EOF");
+			return(-1);
+		}
+
+		switch (rc) {
+		case 0:
+			dgap_err("unexpected end of file");
+			return(-1);
+
+		case BEGIN:	/* should only be 1 begin */
+			dgap_err("unexpected config_begin\n");
+			return(-1);
+
+		case END:
+			return(0);
+
+		case BOARD:	/* board info */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(BNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+
+			p->u.board.status = dgap_savestring("No");
+			line = conc = NULL;
+			brd = p;
+			linecnt = -1;
+			break;
+
+		case APORT2_920P:	/* AccelePort_4 */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_2r_920 string");
+				return(-1);
+			}
+			p->u.board.type = APORT2_920P;
+			p->u.board.v_type = 1;
+			DPR_INIT(("Adding Digi_2r_920 PCI to config...\n"));
+			break;
+
+		case APORT4_920P:	/* AccelePort_4 */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_4r_920 string");
+				return(-1);
+			}
+			p->u.board.type = APORT4_920P;
+			p->u.board.v_type = 1;
+			DPR_INIT(("Adding Digi_4r_920 PCI to config...\n"));
+			break;
+
+		case APORT8_920P:	/* AccelePort_8 */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_8r_920 string");
+				return(-1);
+			}
+			p->u.board.type = APORT8_920P;
+			p->u.board.v_type = 1;
+			DPR_INIT(("Adding Digi_8r_920 PCI to config...\n"));
+			break;
+
+		case PAPORT4:	/* AccelePort_4 PCI */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_4r(PCI) string");
+				return(-1);
+			}
+			p->u.board.type = PAPORT4;
+			p->u.board.v_type = 1;
+			DPR_INIT(("Adding Digi_4r PCI to config...\n"));
+			break;
+
+		case PAPORT8:	/* AccelePort_8 PCI */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_8r string");
+				return(-1);
+			}
+			p->u.board.type = PAPORT8;
+			p->u.board.v_type = 1;
+			DPR_INIT(("Adding Digi_8r PCI to config...\n"));
+			break;
+
+		case PCX:	/* PCI C/X */
+			if (p->type != BNODE) {
+				dgap_err("unexpected Digi_C/X_(PCI) string");
+				return(-1);
+			}
+			p->u.board.type = PCX;
+			p->u.board.v_type = 1;
+			p->u.board.conc1 = 0;
+			p->u.board.conc2 = 0;
+			p->u.board.module1 = 0;
+			p->u.board.module2 = 0;
+			DPR_INIT(("Adding PCI C/X to config...\n"));
+			break;
+
+		case PEPC:	/* PCI EPC/X */
+			if (p->type != BNODE) {
+				dgap_err("unexpected \"Digi_EPC/X_(PCI)\" string");
+				return(-1);
+			}
+			p->u.board.type = PEPC;
+			p->u.board.v_type = 1;
+			p->u.board.conc1 = 0;
+			p->u.board.conc2 = 0;
+			p->u.board.module1 = 0;
+			p->u.board.module2 = 0;
+			DPR_INIT(("Adding PCI EPC/X to config...\n"));
+			break;
+
+		case PPCM:	/* PCI/Xem */
+			if (p->type != BNODE) {
+				dgap_err("unexpected PCI/Xem string");
+				return(-1);
+			}
+			p->u.board.type = PPCM;
+			p->u.board.v_type = 1;
+			p->u.board.conc1 = 0;
+			p->u.board.conc2 = 0;
+			DPR_INIT(("Adding PCI XEM to config...\n"));
+			break;
+
+		case IO:	/* i/o port */
+			if (p->type != BNODE) {
+				dgap_err("IO port only vaild for boards");
+				return(-1);
+			}
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.portstr = dgap_savestring(s);
+			p->u.board.port = (short)simple_strtol(s, &s2, 0);
+			if ((short)strlen(s) > (short)(s2 - s)) {
+				dgap_err("bad number for IO port");
+				return(-1);
+			}
+			p->u.board.v_port = 1;
+			DPR_INIT(("Adding IO (%s) to config...\n", s));
+			break;
+
+		case MEM:	/* memory address */
+			if (p->type != BNODE) {
+				dgap_err("memory address only vaild for boards");
+				return(-1);
+			}
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.addrstr = dgap_savestring(s);
+			p->u.board.addr = simple_strtoul(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for memory address");
+				return(-1);
+			}
+			p->u.board.v_addr = 1;
+			DPR_INIT(("Adding MEM (%s) to config...\n", s));
+			break;
+
+		case PCIINFO:	/* pci information */
+			if (p->type != BNODE) {
+				dgap_err("memory address only vaild for boards");
+				return(-1);
+			}
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.pcibusstr = dgap_savestring(s);
+			p->u.board.pcibus = simple_strtoul(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for pci bus");
+				return(-1);
+			}
+			p->u.board.v_pcibus = 1;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.pcislotstr = dgap_savestring(s);
+			p->u.board.pcislot = simple_strtoul(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for pci slot");
+				return(-1);
+			}
+			p->u.board.v_pcislot = 1;
+
+			DPR_INIT(("Adding PCIINFO (%s %s) to config...\n", p->u.board.pcibusstr, 
+				p->u.board.pcislotstr));
+			break;
+
+		case METHOD:
+			if (p->type != BNODE) {
+				dgap_err("install method only vaild for boards");
+				return(-1);
+			}
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.method = dgap_savestring(s);
+			p->u.board.v_method = 1;
+			DPR_INIT(("Adding METHOD (%s) to config...\n", s));
+			break;
+
+		case STATUS:
+			if (p->type != BNODE) {
+				dgap_err("config status only vaild for boards");
+				return(-1);
+			}
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.board.status = dgap_savestring(s);
+			DPR_INIT(("Adding STATUS (%s) to config...\n", s));
+			break;
+
+		case NPORTS:	/* number of ports */
+			if (p->type == BNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.board.nport = (char)simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for number of ports");
+					return(-1);
+				}
+				p->u.board.v_nport = 1;
+			} else if (p->type == CNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.conc.nport = (char)simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for number of ports");
+					return(-1);
+				}
+				p->u.conc.v_nport = 1;
+			} else if (p->type == MNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.module.nport = (char)simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for number of ports");
+					return(-1);
+				}
+				p->u.module.v_nport = 1;
+			} else {
+				dgap_err("nports only valid for concentrators or modules");
+				return(-1);
+			}
+			DPR_INIT(("Adding NPORTS (%s) to config...\n", s));
+			break;
+
+		case ID:	/* letter ID used in tty name */
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+
+			p->u.board.status = dgap_savestring(s);
+
+			if (p->type == CNODE) {
+				p->u.conc.id = dgap_savestring(s);
+				p->u.conc.v_id = 1;
+			} else if (p->type == MNODE) {
+				p->u.module.id = dgap_savestring(s);
+				p->u.module.v_id = 1;
+			} else {
+				dgap_err("id only valid for concentrators or modules");
+				return(-1);
+			}
+			DPR_INIT(("Adding ID (%s) to config...\n", s));
+			break;
+
+		case STARTO:	/* start offset of ID */
+			if (p->type == BNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.board.start = simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for start of tty count");
+					return(-1);
+				}
+				p->u.board.v_start = 1;
+			} else if (p->type == CNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.conc.start = simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for start of tty count");
+					return(-1);
+				}
+				p->u.conc.v_start = 1;
+			} else if (p->type == MNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.module.start = simple_strtol(s, &s2, 0);
+				if ((int)strlen(s) > (int)(s2 - s)) {
+					dgap_err("bad number for start of tty count");
+					return(-1);
+				}
+				p->u.module.v_start = 1;
+			} else {
+				dgap_err("start only valid for concentrators or modules");
+				return(-1);
+			}
+			DPR_INIT(("Adding START (%s) to config...\n", s));
+			break;
+
+		case TTYN:	/* tty name prefix */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(TNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			if ( (s = dgap_getword(in)) == NULL ) {
+				dgap_err("unexpeced end of file");
+				return(-1);
+			}
+			if ( (p->u.ttyname = dgap_savestring(s)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			DPR_INIT(("Adding TTY (%s) to config...\n", s));
+			break;
+
+		case CU:	/* cu name prefix */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(CUNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			if ( (s = dgap_getword(in)) == NULL ) {
+				dgap_err("unexpeced end of file");
+				return(-1);
+			}
+			if ( (p->u.cuname = dgap_savestring(s)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			DPR_INIT(("Adding CU (%s) to config...\n", s));
+			break;
+
+		case LINE:	/* line information */
+			if (dgap_checknode(p))
+				return(-1);
+			if (brd == NULL) {
+				dgap_err("must specify board before line info");
+				return(-1);
+			}
+			switch (brd->u.board.type) {
+			case PPCM:
+				dgap_err("line not vaild for PC/em");
+				return(-1);
+			}
+			if ( (p->next = dgap_newnode(LNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			conc = NULL;
+			line = p;
+			linecnt++;
+			DPR_INIT(("Adding LINE to config...\n"));
+			break;
+
+		case CONC:	/* concentrator information */
+			if (dgap_checknode(p))
+				return(-1);
+			if (line == NULL) {
+				dgap_err("must specify line info before concentrator");
+				return(-1);
+			}
+			if ( (p->next = dgap_newnode(CNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			conc = p;
+			if (linecnt)
+				brd->u.board.conc2++;
+			else
+				brd->u.board.conc1++;
+
+			DPR_INIT(("Adding CONC to config...\n"));
+			break;
+
+		case CX:	/* c/x type concentrator */
+			if (p->type != CNODE) {
+				dgap_err("cx only valid for concentrators");
+				return(-1);
+			}
+			p->u.conc.type = CX;
+			p->u.conc.v_type = 1;
+			DPR_INIT(("Adding CX to config...\n"));
+			break;
+
+		case EPC:	/* epc type concentrator */
+			if (p->type != CNODE) {
+				dgap_err("cx only valid for concentrators");
+				return(-1);
+			}
+			p->u.conc.type = EPC;
+			p->u.conc.v_type = 1;
+			DPR_INIT(("Adding EPC to config...\n"));
+			break;
+
+		case MOD:	/* EBI module */
+			if (dgap_checknode(p))
+				return(-1);
+			if (brd == NULL) {
+				dgap_err("must specify board info before EBI modules");
+				return(-1);
+			}
+			switch (brd->u.board.type) {
+			case PPCM:
+				linecnt = 0;
+				break;
+			default:
+				if (conc == NULL) {
+					dgap_err("must specify concentrator info before EBI module");
+					return(-1);
+				}
+			}
+			if ( (p->next = dgap_newnode(MNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			if (linecnt)
+				brd->u.board.module2++;
+			else
+				brd->u.board.module1++;
+
+			DPR_INIT(("Adding MOD to config...\n"));
+			break;
+
+		case PORTS:	/* ports type EBI module */
+			if (p->type != MNODE) {
+				dgap_err("ports only valid for EBI modules");
+				return(-1);
+			}
+			p->u.module.type = PORTS;
+			p->u.module.v_type = 1;
+			DPR_INIT(("Adding PORTS to config...\n"));
+			break;
+
+		case MODEM:	/* ports type EBI module */
+			if (p->type != MNODE) {
+				dgap_err("modem only valid for modem modules");
+				return(-1);
+			}
+			p->u.module.type = MODEM;
+			p->u.module.v_type = 1;
+			DPR_INIT(("Adding MODEM to config...\n"));
+			break;
+
+		case CABLE:
+			if (p->type == LNODE) {
+				if ((s = dgap_getword(in)) == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.line.cable = dgap_savestring(s);
+				p->u.line.v_cable = 1;
+			}
+			DPR_INIT(("Adding CABLE (%s) to config...\n", s));
+			break;
+
+		case SPEED:	/* sync line speed indication */
+			if (p->type == LNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.line.speed = (char)simple_strtol(s, &s2, 0);
+				if ((short)strlen(s) > (short)(s2 - s)) {
+					dgap_err("bad number for line speed");
+					return(-1);
+				}
+				p->u.line.v_speed = 1;
+			} else if (p->type == CNODE) {
+				s = dgap_getword(in);
+				if (s == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.conc.speed = (char)simple_strtol(s, &s2, 0);
+				if ((short)strlen(s) > (short)(s2 - s)) {
+					dgap_err("bad number for line speed");
+					return(-1);
+				}
+				p->u.conc.v_speed = 1;
+			} else {
+				dgap_err("speed valid only for lines or concentrators.");
+				return(-1);
+			}
+			DPR_INIT(("Adding SPEED (%s) to config...\n", s));
+			break;
+
+		case CONNECT:
+			if (p->type == CNODE) {
+				if ((s = dgap_getword(in)) == NULL) {
+					dgap_err("unexpected end of file");
+					return(-1);
+				}
+				p->u.conc.connect = dgap_savestring(s);
+				p->u.conc.v_connect = 1;
+			}
+			DPR_INIT(("Adding CONNECT (%s) to config...\n", s));
+			break;
+		case PRINT:	/* transparent print name prefix */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(PNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			if ( (s = dgap_getword(in)) == NULL ) {
+				dgap_err("unexpeced end of file");
+				return(-1);
+			}
+			if ( (p->u.printname = dgap_savestring(s)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			DPR_INIT(("Adding PRINT (%s) to config...\n", s));
+			break;
+
+		case CMAJOR:	/* major number */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(JNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.majornumber = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for major number");
+				return(-1);
+			}
+			DPR_INIT(("Adding CMAJOR (%s) to config...\n", s));
+			break;
+
+		case ALTPIN:	/* altpin setting */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(ANODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.altpin = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for altpin");
+				return(-1);
+			}
+			DPR_INIT(("Adding ALTPIN (%s) to config...\n", s));
+			break;
+
+		case USEINTR:		/* enable interrupt setting */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(INTRNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.useintr = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for useintr");
+				return(-1);
+			}
+			DPR_INIT(("Adding USEINTR (%s) to config...\n", s));
+			break;
+
+		case TTSIZ:	/* size of tty structure */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(TSNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.ttysize = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for ttysize");
+				return(-1);
+			}
+			DPR_INIT(("Adding TTSIZ (%s) to config...\n", s));
+			break;
+
+		case CHSIZ:	/* channel structure size */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(CSNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.chsize = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for chsize");
+				return(-1);
+			}
+			DPR_INIT(("Adding CHSIZE (%s) to config...\n", s));
+			break;
+
+		case BSSIZ:	/* board structure size */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(BSNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.bssize = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for bssize");
+				return(-1);
+			}
+			DPR_INIT(("Adding BSSIZ (%s) to config...\n", s));
+			break;
+
+		case UNTSIZ:	/* sched structure size */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(USNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.unsize = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for schedsize");
+				return(-1);
+			}
+			DPR_INIT(("Adding UNTSIZ (%s) to config...\n", s));
+			break;
+
+		case F2SIZ:	/* f2200 structure size */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(FSNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.f2size = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for f2200size");
+				return(-1);
+			}
+			DPR_INIT(("Adding F2SIZ (%s) to config...\n", s));
+			break;
+
+		case VPSIZ:	/* vpix structure size */
+			if (dgap_checknode(p))
+				return(-1);
+			if ( (p->next = dgap_newnode(VSNODE)) == NULL ) {
+				dgap_err("out of memory");
+				return(-1);
+			}
+			p = p->next;
+			s = dgap_getword(in);
+			if (s == NULL) {
+				dgap_err("unexpected end of file");
+				return(-1);
+			}
+			p->u.vpixsize = simple_strtol(s, &s2, 0);
+			if ((int)strlen(s) > (int)(s2 - s)) {
+				dgap_err("bad number for vpixsize");
+				return(-1);
+			}
+			DPR_INIT(("Adding VPSIZ (%s) to config...\n", s));
+			break;
+		}
+	}
+}
+
+
+/*
+ * dgap_sindex: much like index(), but it looks for a match of any character in
+ * the group, and returns that position.  If the first character is a ^, then
+ * this will match the first occurrence not in that group.
+ */
+static char *dgap_sindex (char *string, char *group)
+{
+	char    *ptr;
+
+	if (!string || !group)
+		return (char *) NULL;
+
+	if (*group == '^') {   
+		group++;
+		for (; *string; string++) {
+			for (ptr = group; *ptr; ptr++) {
+				if (*ptr == *string)
+					break;
+			}
+			if (*ptr == '\0')
+				return string;
+		}
+	}   
+	else {
+		for (; *string; string++) {
+			for (ptr = group; *ptr; ptr++) {
+				if (*ptr == *string)
+					return string;
+			}
+		}
+	}
+
+	return (char *) NULL;
+}
+
+
+/*
+ * Get a token from the input file; return 0 if end of file is reached
+ */
+static int dgap_gettok(char **in, struct cnode *p)
+{
+	char	*w;
+	struct toklist *t;
+	
+	if (strstr(dgap_cword, "boar")) {
+		w = dgap_getword(in);
+		snprintf(dgap_cword, MAXCWORD, "%s", w);
+		for (t = dgap_tlist; t->token != 0; t++) {
+			if ( !strcmp(w, t->string)) {
+				return(t->token);
+			} 
+		}
+		dgap_err("board !!type not specified");
+		return(1);
+	}
+	else {
+		while ( (w = dgap_getword(in)) != NULL ) {
+			snprintf(dgap_cword, MAXCWORD, "%s", w);
+			for (t = dgap_tlist; t->token != 0; t++) {
+				if ( !strcmp(w, t->string) )
+					return(t->token);
+			}
+		}
+		return(0);
+	}
+}
+
+
+/*
+ * get a word from the input stream, also keep track of current line number.
+ * words are separated by whitespace.
+ */
+static char *dgap_getword(char **in)
+{
+	char *ret_ptr = *in;
+
+        char *ptr = dgap_sindex(*in, " \t\n");
+
+	/* If no word found, return null */
+	if (!ptr)
+		return NULL;
+
+	/* Mark new location for our buffer */
+	*ptr = '\0';
+	*in = ptr + 1;
+
+	/* Eat any extra spaces/tabs/newlines that might be present */
+	while (*in && **in && ((**in == ' ') || (**in == '\t') || (**in == '\n'))) {
+		**in = '\0';
+		*in = *in + 1;
+	}
+
+	return ret_ptr;
+}
+
+
+/*
+ * print an error message, giving the line number in the file where
+ * the error occurred.
+ */
+static void dgap_err(char *s)
+{
+	printk("DGAP: parse: %s\n", s);
+}
+
+
+/*
+ * allocate a new configuration node of type t
+ */
+static struct cnode *dgap_newnode(int t)
+{
+	struct cnode *n;
+
+	n = kmalloc(sizeof(struct cnode), GFP_ATOMIC);
+	if (n != NULL) {
+		memset((char *)n, 0, sizeof(struct cnode));
+		n->type = t;
+	}
+	return(n);
+}
+
+
+/*
+ * dgap_checknode: see if all the necessary info has been supplied for a node
+ * before creating the next node.
+ */
+static int dgap_checknode(struct cnode *p)
+{
+	switch (p->type) {
+	case BNODE:
+		if (p->u.board.v_type == 0) {
+			dgap_err("board type !not specified");
+			return(1);
+		}
+
+		return(0);
+
+	case LNODE:
+		if (p->u.line.v_speed == 0) {
+			dgap_err("line speed not specified");
+			return(1);
+		}
+		return(0);
+
+	case CNODE:
+		if (p->u.conc.v_type == 0) {
+			dgap_err("concentrator type not specified");
+			return(1);
+		}
+		if (p->u.conc.v_speed == 0) {
+			dgap_err("concentrator line speed not specified");
+			return(1);
+		}
+		if (p->u.conc.v_nport == 0) {
+			dgap_err("number of ports on concentrator not specified");
+			return(1);
+		}
+		if (p->u.conc.v_id == 0) {
+			dgap_err("concentrator id letter not specified");
+			return(1);
+		}
+		return(0);
+
+	case MNODE:
+		if (p->u.module.v_type == 0) {
+			dgap_err("EBI module type not specified");
+			return(1);
+		}
+		if (p->u.module.v_nport == 0) {
+			dgap_err("number of ports on EBI module not specified");
+			return(1);
+		}
+		if (p->u.module.v_id == 0) {
+			dgap_err("EBI module id letter not specified");
+			return(1);
+		}
+		return(0);
+	}
+	return(0);
+}
+
+/*
+ * save a string somewhere
+ */
+static char	*dgap_savestring(char *s)
+{
+	char	*p;
+	if ( (p = kmalloc(strlen(s) + 1, GFP_ATOMIC) ) != NULL) {
+		strcpy(p, s);
+	}
+	return(p);
+}
+
+
+/*
+ * Given a board pointer, returns whether we should use interrupts or not.
+ */
+uint dgap_config_get_useintr(struct board_t *bd)
+{
+	struct cnode *p = NULL;
+
+	if (!bd)
+		return(0);
+
+	for (p = bd->bd_config; p; p = p->next) {
+		switch (p->type) {
+		case INTRNODE:
+			/*
+			 * check for pcxr types.
+			 */
+			return p->u.useintr;
+		default:
+			break;
+		}
+	}
+
+	/* If not found, then don't turn on interrupts. */
+	return 0;
+}
+
+
+/*
+ * Given a board pointer, returns whether we turn on altpin or not.
+ */
+uint dgap_config_get_altpin(struct board_t *bd)
+{
+	struct cnode *p = NULL;
+
+	if (!bd)
+		return(0);
+
+	for (p = bd->bd_config; p; p = p->next) {
+		switch (p->type) {
+		case ANODE:
+			/*
+			 * check for pcxr types.
+			 */
+			return p->u.altpin;
+		default:
+			break;
+		}
+	}
+
+	/* If not found, then don't turn on interrupts. */
+	return 0;
+}
+
+
+
+/*
+ * Given a specific type of board, if found, detached link and 
+ * returns the first occurrence in the list.
+ */
+struct cnode *dgap_find_config(int type, int bus, int slot)
+{
+	struct cnode *p, *prev = NULL, *prev2 = NULL, *found = NULL;
+
+	p = &dgap_head;
+
+	while (p->next != NULL) {
+		prev = p;
+		p = p->next;
+
+		if (p->type == BNODE) {
+
+			if (p->u.board.type == type) {
+
+				if (p->u.board.v_pcibus && p->u.board.pcibus != bus) {
+					DPR(("Found matching board, but wrong bus position. System says bus %d, we want bus %ld\n",
+						bus, p->u.board.pcibus));
+					continue;
+				}
+				if (p->u.board.v_pcislot && p->u.board.pcislot != slot) {
+					DPR_INIT(("Found matching board, but wrong slot position. System says slot %d, we want slot %ld\n",
+						slot, p->u.board.pcislot));
+					continue;
+				}
+
+				DPR_INIT(("Matched type in config file\n"));
+
+				found = p;
+				/*
+				 * Keep walking thru the list till we find the next board.
+				 */
+				while (p->next != NULL) {
+					prev2 = p;
+					p = p->next;
+					if (p->type == BNODE) {
+
+						/*
+						 * Mark the end of our 1 board chain of configs.
+						 */
+						prev2->next = NULL;
+
+						/*
+						 * Link the "next" board to the previous board,
+						 * effectively "unlinking" our board from the main config.
+						 */
+						prev->next = p;
+
+						return found;
+					}
+				}
+				/*
+				 * It must be the last board in the list.
+				 */
+				prev->next = NULL;
+				return found;
+			}
+		}
+	}
+	return NULL;
+}
+
+/*
+ * Given a board pointer, walks the config link, counting up
+ * all ports user specified should be on the board.
+ * (This does NOT mean they are all actually present right now tho)
+ */
+uint dgap_config_get_number_of_ports(struct board_t *bd)
+{
+	int count = 0;
+	struct cnode *p = NULL;
+
+	if (!bd)
+		return(0);
+
+	for (p = bd->bd_config; p; p = p->next) {
+
+		switch (p->type) {
+		case BNODE:
+			/*
+			 * check for pcxr types.
+			 */
+			if (p->u.board.type > EPCFE)
+				count += p->u.board.nport;
+			break;
+		case CNODE:
+			count += p->u.conc.nport;
+			break;
+		case MNODE:
+			count += p->u.module.nport;
+			break;
+		}
+	}
+	return (count);
+}
+
+char *dgap_create_config_string(struct board_t *bd, char *string)
+{
+	char *ptr = string;
+	struct cnode *p = NULL;
+	struct cnode *q = NULL;
+	int speed;
+
+	if (!bd) {
+		*ptr = 0xff;
+		return string;
+	}
+
+	for (p = bd->bd_config; p; p = p->next) {
+
+		switch (p->type) {
+		case LNODE:
+			*ptr = '\0';
+			ptr++;
+			*ptr = p->u.line.speed;
+			ptr++;
+			break;
+		case CNODE:
+			/*
+			 * Because the EPC/con concentrators can have EM modules
+			 * hanging off of them, we have to walk ahead in the list
+			 * and keep adding the number of ports on each EM to the config.
+			 * UGH!
+			 */
+			speed = p->u.conc.speed;
+			q = p->next;
+			if ((q != NULL) && (q->type == MNODE) ) {
+				*ptr = (p->u.conc.nport + 0x80);
+				ptr++;
+				p = q;
+				while ((q->next != NULL) && (q->next->type) == MNODE) {
+					*ptr = (q->u.module.nport + 0x80);
+					ptr++;
+					p = q;
+					q = q->next;
+				}
+				*ptr = q->u.module.nport;
+				ptr++;
+			} else {
+				*ptr = p->u.conc.nport;
+				ptr++;
+			}
+
+			*ptr = speed;
+			ptr++;
+			break;
+		}
+	}
+
+	*ptr = 0xff;
+	return string;
+}
+
+
+
+char *dgap_get_config_letters(struct board_t *bd, char *string)
+{
+	int found = FALSE;
+	char *ptr = string;
+	struct cnode *cptr = NULL;
+	int len = 0;
+	int left = MAXTTYNAMELEN;
+
+	if (!bd) {
+		return "<NULL>";
+	}
+
+	for (cptr = bd->bd_config; cptr; cptr = cptr->next) {
+
+		if ((cptr->type == BNODE) &&
+		     ((cptr->u.board.type == APORT2_920P) || (cptr->u.board.type == APORT4_920P) ||
+		     (cptr->u.board.type == APORT8_920P) || (cptr->u.board.type == PAPORT4) ||
+		     (cptr->u.board.type == PAPORT8))) {
+
+			found = TRUE;
+		}
+
+		if (cptr->type == TNODE && found == TRUE) {
+			char *ptr1;
+			if (strstr(cptr->u.ttyname, "tty")) {
+				ptr1 = cptr->u.ttyname;
+				ptr1 += 3;
+			}
+			else {
+				ptr1 = cptr->u.ttyname;
+			}
+			if (ptr1) {
+				len = snprintf(ptr, left, "%s", ptr1);
+				left -= len;
+				ptr  += len;
+				if (left <= 0)
+					break;
+			}
+		}
+
+		if (cptr->type == CNODE) {
+			if (cptr->u.conc.id) {
+				len = snprintf(ptr, left, "%s", cptr->u.conc.id);
+				left -= len;
+				ptr  += len;
+				if (left <= 0)
+					break;
+			}
+                }
+
+		if (cptr->type == MNODE) {
+			if (cptr->u.module.id) {
+				len = snprintf(ptr, left, "%s", cptr->u.module.id);
+				left -= len;
+				ptr  += len;
+				if (left <= 0)
+					break;
+			}
+		}
+	}
+
+	return string;
+}
+
+/************************************************************************
+ *                      
+ * TTY Initialization/Cleanup Functions
+ *      
+ ************************************************************************/
+         
+/*
+ * dgap_tty_preinit()
+ *
+ * Initialize any global tty related data before we download any boards.
+ */
+int dgap_tty_preinit(void)
+{
+	unsigned long flags;
+
+	DGAP_LOCK(dgap_global_lock, flags);  
+
+	/*
+	 * Allocate a buffer for doing the copy from user space to
+	 * kernel space in dgap_input().  We only use one buffer and
+	 * control access to it with a semaphore.  If we are paging, we
+	 * are already in trouble so one buffer won't hurt much anyway.
+	 */
+	dgap_TmpWriteBuf = kmalloc(WRITEBUFLEN, GFP_ATOMIC);
+
+	if (!dgap_TmpWriteBuf) {
+		DGAP_UNLOCK(dgap_global_lock, flags);
+		DPR_INIT(("unable to allocate tmp write buf"));
+		return (-ENOMEM);
+	}
+         
+        DGAP_UNLOCK(dgap_global_lock, flags);
+        return(0);
+}
+
+
+/*
+ * dgap_tty_register()
+ *
+ * Init the tty subsystem for this board.
+ */
+int dgap_tty_register(struct board_t *brd)
+{
+	int rc = 0;
+
+	DPR_INIT(("tty_register start"));
+
+	brd->SerialDriver = alloc_tty_driver(MAXPORTS);
+
+	snprintf(brd->SerialName, MAXTTYNAMELEN, "tty_dgap_%d_", brd->boardnum);
+	brd->SerialDriver->name = brd->SerialName;
+	brd->SerialDriver->name_base = 0;
+	brd->SerialDriver->major = 0;
+	brd->SerialDriver->minor_start = 0;
+	brd->SerialDriver->type = TTY_DRIVER_TYPE_SERIAL; 
+	brd->SerialDriver->subtype = SERIAL_TYPE_NORMAL;   
+	brd->SerialDriver->init_termios = DgapDefaultTermios;
+	brd->SerialDriver->driver_name = DRVSTR;
+	brd->SerialDriver->flags = (TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_HARDWARE_BREAK);
+
+	/* The kernel wants space to store pointers to tty_structs */
+	brd->SerialDriver->ttys = dgap_driver_kzmalloc(MAXPORTS * sizeof(struct tty_struct *), GFP_KERNEL);
+	if (!brd->SerialDriver->ttys)
+		return(-ENOMEM);
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
+	brd->SerialDriver->refcount = brd->TtyRefCnt;
+#endif
+
+	/*
+	 * Entry points for driver.  Called by the kernel from
+	 * tty_io.c and n_tty.c.
+	 */
+	tty_set_operations(brd->SerialDriver, &dgap_tty_ops);
+
+	/*
+	 * If we're doing transparent print, we have to do all of the above
+	 * again, separately so we don't get the LD confused about what major
+	 * we are when we get into the dgap_tty_open() routine.
+	 */
+	brd->PrintDriver = alloc_tty_driver(MAXPORTS);
+
+	snprintf(brd->PrintName, MAXTTYNAMELEN, "pr_dgap_%d_", brd->boardnum);
+	brd->PrintDriver->name = brd->PrintName;
+	brd->PrintDriver->name_base = 0;
+	brd->PrintDriver->major = 0;
+	brd->PrintDriver->minor_start = 0;
+	brd->PrintDriver->type = TTY_DRIVER_TYPE_SERIAL;   
+	brd->PrintDriver->subtype = SERIAL_TYPE_NORMAL;
+	brd->PrintDriver->init_termios = DgapDefaultTermios;
+	brd->PrintDriver->driver_name = DRVSTR;
+	brd->PrintDriver->flags = (TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_HARDWARE_BREAK);
+
+	/* The kernel wants space to store pointers to tty_structs */
+	brd->PrintDriver->ttys = dgap_driver_kzmalloc(MAXPORTS * sizeof(struct tty_struct *), GFP_KERNEL);
+	if (!brd->PrintDriver->ttys)
+		return(-ENOMEM);
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
+	brd->PrintDriver->refcount = brd->TtyRefCnt;
+#endif
+
+	/*
+	 * Entry points for driver.  Called by the kernel from
+	 * tty_io.c and n_tty.c.
+	 */
+	tty_set_operations(brd->PrintDriver, &dgap_tty_ops);
+
+	if (!brd->dgap_Major_Serial_Registered) {
+		/* Register tty devices */
+		rc = tty_register_driver(brd->SerialDriver);
+		if (rc < 0) {
+			APR(("Can't register tty device (%d)\n", rc));
+			return(rc);
+		}
+		brd->dgap_Major_Serial_Registered = TRUE;
+		dgap_BoardsByMajor[brd->SerialDriver->major] = brd;
+		brd->dgap_Serial_Major = brd->SerialDriver->major;
+	}
+
+	if (!brd->dgap_Major_TransparentPrint_Registered) {
+		/* Register Transparent Print devices */
+ 		rc = tty_register_driver(brd->PrintDriver);
+		if (rc < 0) {
+			APR(("Can't register Transparent Print device (%d)\n", rc));
+			return(rc);
+		}
+		brd->dgap_Major_TransparentPrint_Registered = TRUE;
+		dgap_BoardsByMajor[brd->PrintDriver->major] = brd;
+		brd->dgap_TransparentPrint_Major = brd->PrintDriver->major;
+	}
+
+	DPR_INIT(("DGAP REGISTER TTY: MAJORS: %d %d\n", brd->SerialDriver->major,
+		brd->PrintDriver->major));
+
+	return (rc);
+}
+
+
+/*
+ * dgap_tty_init()
+ *
+ * Init the tty subsystem.  Called once per board after board has been
+ * downloaded and init'ed.
+ */
+int dgap_tty_init(struct board_t *brd)
+{
+	int i;
+	int tlw;
+	uint true_count = 0;
+	uchar *vaddr;
+	uchar modem = 0;
+	struct channel_t *ch;
+	struct bs_t *bs;
+	struct cm_t *cm;
+
+	if (!brd)
+		return (-ENXIO);
+
+	DPR_INIT(("dgap_tty_init start\n"));
+
+	/*
+	 * Initialize board structure elements.
+	 */
+
+	vaddr = brd->re_map_membase;
+	true_count = readw((vaddr + NCHAN));
+
+	brd->nasync = dgap_config_get_number_of_ports(brd);
+
+	if (!brd->nasync) {
+		brd->nasync = brd->maxports;
+	}
+
+	if (brd->nasync > brd->maxports) {
+		brd->nasync = brd->maxports;
+	}
+
+	if (true_count != brd->nasync) {
+		if ((brd->type == PPCM) && (true_count == 64)) {
+			APR(("***WARNING**** %s configured for %d ports, has %d ports.\nPlease make SURE the EBI cable running from the card\nto each EM module is plugged into EBI IN!\n",
+				brd->name, brd->nasync, true_count));
+		}
+		else if ((brd->type == PPCM) && (true_count == 0)) {
+			APR(("***WARNING**** %s configured for %d ports, has %d ports.\nPlease make SURE the EBI cable running from the card\nto each EM module is plugged into EBI IN!\n",
+				brd->name, brd->nasync, true_count));
+		}
+		else {
+			APR(("***WARNING**** %s configured for %d ports, has %d ports.\n",
+				brd->name, brd->nasync, true_count));
+		}
+
+		brd->nasync = true_count;
+
+		/* If no ports, don't bother going any further */
+		if (!brd->nasync) {
+			brd->state = BOARD_FAILED;
+			brd->dpastatus = BD_NOFEP;
+			return(-ENXIO);
+		}
+	}
+
+	/*
+	 * Allocate channel memory that might not have been allocated
+	 * when the driver was first loaded.
+	 */
+	for (i = 0; i < brd->nasync; i++) {
+		if (!brd->channels[i]) {
+			brd->channels[i] = dgap_driver_kzmalloc(sizeof(struct channel_t), GFP_ATOMIC);
+			if (!brd->channels[i]) {
+				DPR_CORE(("%s:%d Unable to allocate memory for channel struct\n",
+				    __FILE__, __LINE__));
+			}
+		}
+	}
+
+	ch = brd->channels[0];
+	vaddr = brd->re_map_membase;
+
+	bs = (struct bs_t *) ((ulong) vaddr + CHANBUF);
+	cm = (struct cm_t *) ((ulong) vaddr + CMDBUF);
+
+	brd->bd_bs = bs;
+
+	/* Set up channel variables */
+	for (i = 0; i < brd->nasync; i++, ch = brd->channels[i], bs++) {
+
+		if (!brd->channels[i])
+			continue;
+
+		DGAP_SPINLOCK_INIT(ch->ch_lock);
+
+		/* Store all our magic numbers */
+		ch->magic = DGAP_CHANNEL_MAGIC;
+		ch->ch_tun.magic = DGAP_UNIT_MAGIC;
+		ch->ch_tun.un_type = DGAP_SERIAL;
+		ch->ch_tun.un_ch = ch;
+		ch->ch_tun.un_dev = i;
+
+		ch->ch_pun.magic = DGAP_UNIT_MAGIC;
+		ch->ch_pun.un_type = DGAP_PRINT;
+		ch->ch_pun.un_ch = ch;
+		ch->ch_pun.un_dev = i;
+
+		ch->ch_vaddr = vaddr;
+		ch->ch_bs = bs;
+		ch->ch_cm = cm;
+		ch->ch_bd = brd;
+		ch->ch_portnum = i;
+		ch->ch_digi = dgap_digi_init;
+
+		/*
+		 * Set up digi dsr and dcd bits based on altpin flag.
+		 */
+		if (dgap_config_get_altpin(brd)) {
+			ch->ch_dsr	= DM_CD;
+			ch->ch_cd	= DM_DSR;
+			ch->ch_digi.digi_flags |= DIGI_ALTPIN;
+		}
+		else {
+			ch->ch_cd	= DM_CD;
+			ch->ch_dsr	= DM_DSR;
+		}
+
+		ch->ch_taddr = vaddr + ((ch->ch_bs->tx_seg) << 4);
+		ch->ch_raddr = vaddr + ((ch->ch_bs->rx_seg) << 4);
+		ch->ch_tx_win = 0;
+		ch->ch_rx_win = 0;
+		ch->ch_tsize = readw(&(ch->ch_bs->tx_max)) + 1;
+		ch->ch_rsize = readw(&(ch->ch_bs->rx_max)) + 1;
+		ch->ch_tstart = 0;
+		ch->ch_rstart = 0;
+
+		/* .25 second delay */
+		ch->ch_close_delay = 250;
+
+		/*
+		 * Set queue water marks, interrupt mask,
+		 * and general tty parameters. 
+		 */
+		ch->ch_tlw = tlw = ch->ch_tsize >= 2000 ? ((ch->ch_tsize * 5) / 8) : ch->ch_tsize / 2;
+
+		dgap_cmdw(ch, STLOW, tlw, 0);
+
+		dgap_cmdw(ch, SRLOW, ch->ch_rsize / 2, 0);
+
+		dgap_cmdw(ch, SRHIGH, 7 * ch->ch_rsize / 8, 0);
+
+		ch->ch_mistat = readb(&(ch->ch_bs->m_stat));
+
+		init_waitqueue_head(&ch->ch_flags_wait);
+		init_waitqueue_head(&ch->ch_tun.un_flags_wait);
+		init_waitqueue_head(&ch->ch_pun.un_flags_wait);
+		init_waitqueue_head(&ch->ch_sniff_wait);
+
+		/* Turn on all modem interrupts for now */
+		modem = (DM_CD | DM_DSR | DM_CTS | DM_RI);
+		writeb(modem, &(ch->ch_bs->m_int));
+
+		/*
+		 * Set edelay to 0 if interrupts are turned on,
+		 * otherwise set edelay to the usual 100.
+		 */
+		if (brd->intr_used)
+			writew(0, &(ch->ch_bs->edelay));
+		else
+			writew(100, &(ch->ch_bs->edelay));
+	
+		writeb(1, &(ch->ch_bs->idata));
+	}
+
+
+	DPR_INIT(("dgap_tty_init finish\n"));
+
+	return (0);
+}
+
+
+/*
+ * dgap_tty_post_uninit()
+ *
+ * UnInitialize any global tty related data.
+ */
+void dgap_tty_post_uninit(void)
+{
+	kfree(dgap_TmpWriteBuf);
+	dgap_TmpWriteBuf = NULL;
+}
+
+
+/*
+ * dgap_tty_uninit()
+ *
+ * Uninitialize the TTY portion of this driver.  Free all memory and
+ * resources. 
+ */
+void dgap_tty_uninit(struct board_t *brd)
+{
+	int i = 0;
+
+	if (brd->dgap_Major_Serial_Registered) {
+		dgap_BoardsByMajor[brd->SerialDriver->major] = NULL;
+		brd->dgap_Serial_Major = 0;
+		for (i = 0; i < brd->nasync; i++) {
+			dgap_remove_tty_sysfs(brd->channels[i]->ch_tun.un_sysfs);
+			tty_unregister_device(brd->SerialDriver, i);
+		}
+		tty_unregister_driver(brd->SerialDriver);
+		kfree(brd->SerialDriver->ttys);
+		brd->SerialDriver->ttys = NULL;
+		put_tty_driver(brd->SerialDriver);
+		brd->dgap_Major_Serial_Registered = FALSE;
+	}
+
+	if (brd->dgap_Major_TransparentPrint_Registered) {
+		dgap_BoardsByMajor[brd->PrintDriver->major] = NULL;
+		brd->dgap_TransparentPrint_Major = 0;
+		for (i = 0; i < brd->nasync; i++) {
+			dgap_remove_tty_sysfs(brd->channels[i]->ch_pun.un_sysfs);
+			tty_unregister_device(brd->PrintDriver, i);
+		}
+		tty_unregister_driver(brd->PrintDriver);
+		kfree(brd->PrintDriver->ttys);
+		brd->PrintDriver->ttys = NULL;
+		put_tty_driver(brd->PrintDriver);
+		brd->dgap_Major_TransparentPrint_Registered = FALSE;
+	}
+}
+
+
+#define TMPBUFLEN (1024)
+
+/*
+ * dgap_sniff - Dump data out to the "sniff" buffer if the
+ * proc sniff file is opened...
+ */
+static void dgap_sniff_nowait_nolock(struct channel_t *ch, uchar *text, uchar *buf, int len)
+{
+	struct timeval tv;
+	int n;
+	int r;
+	int nbuf;
+	int i;
+	int tmpbuflen;
+	char tmpbuf[TMPBUFLEN];
+	char *p = tmpbuf;
+	int too_much_data;
+
+	/* Leave if sniff not open */
+	if (!(ch->ch_sniff_flags & SNIFF_OPEN))
+		return;
+
+	do_gettimeofday(&tv);
+
+	/* Create our header for data dump */
+	p += sprintf(p, "<%ld %ld><%s><", tv.tv_sec, tv.tv_usec, text);
+	tmpbuflen = p - tmpbuf;
+
+	do {
+		too_much_data = 0;
+
+		for (i = 0; i < len && tmpbuflen < (TMPBUFLEN - 4); i++) {
+			p += sprintf(p, "%02x ", *buf);
+			buf++;
+			tmpbuflen = p - tmpbuf;
+		}
+
+		if (tmpbuflen < (TMPBUFLEN - 4)) {
+			if (i > 0)
+				p += sprintf(p - 1, "%s\n", ">");
+			else
+				p += sprintf(p, "%s\n", ">");
+		} else {
+			too_much_data = 1;
+			len -= i;
+		}
+
+		nbuf = strlen(tmpbuf);
+		p = tmpbuf;
+
+		/*
+		 *  Loop while data remains.
+		 */
+		while (nbuf > 0 && ch->ch_sniff_buf) {
+			/*
+			 *  Determine the amount of available space left in the
+			 *  buffer.  If there's none, wait until some appears.
+			 */
+			n = (ch->ch_sniff_out - ch->ch_sniff_in - 1) & SNIFF_MASK;
+
+			/*
+			 * If there is no space left to write to in our sniff buffer,
+			 * we have no choice but to drop the data.
+			 * We *cannot* sleep here waiting for space, because this
+			 * function was probably called by the interrupt/timer routines!
+			 */
+			if (n == 0) {
+				return;
+			}
+	
+			/*
+			 * Copy as much data as will fit.
+			 */
+
+			if (n > nbuf)
+				n = nbuf;
+
+			r = SNIFF_MAX - ch->ch_sniff_in;
+
+			if (r <= n) {
+				memcpy(ch->ch_sniff_buf + ch->ch_sniff_in, p, r);
+
+				n -= r;
+				ch->ch_sniff_in = 0;
+				p += r;
+				nbuf -= r;
+			}
+
+			memcpy(ch->ch_sniff_buf + ch->ch_sniff_in, p, n);
+
+			ch->ch_sniff_in += n;
+			p += n;
+			nbuf -= n;
+
+			/*
+			 *  Wakeup any thread waiting for data
+			 */
+			if (ch->ch_sniff_flags & SNIFF_WAIT_DATA) {
+				ch->ch_sniff_flags &= ~SNIFF_WAIT_DATA;
+				wake_up_interruptible(&ch->ch_sniff_wait);
+			}
+		}
+
+		/*
+		 * If the user sent us too much data to push into our tmpbuf,
+		 * we need to keep looping around on all the data.
+		 */
+		if (too_much_data) {
+			p = tmpbuf;
+			tmpbuflen = 0;
+		}
+
+	} while (too_much_data);
+}
+
+
+/*=======================================================================
+ *
+ *      dgap_input - Process received data.
+ * 
+ *              ch      - Pointer to channel structure.
+ * 
+ *=======================================================================*/
+
+void dgap_input(struct channel_t *ch)
+{
+	struct board_t *bd;
+	struct bs_t	*bs;
+	struct tty_struct *tp;
+	struct tty_ldisc *ld;
+	uint	rmask;
+	uint	head;
+	uint	tail;
+	int	data_len;
+	ulong	lock_flags;
+	ulong   lock_flags2;
+	int flip_len;
+	int len = 0;
+	int n = 0;
+	uchar *buf;
+	uchar tmpchar;
+	int s = 0;
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	tp = ch->ch_tun.un_tty;
+
+	bs  = ch->ch_bs;
+	if (!bs) {
+		return;
+	}
+
+	bd = ch->ch_bd;
+	if(!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_READ(("dgap_input start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	/* 
+	 *      Figure the number of characters in the buffer.   
+	 *      Exit immediately if none.
+	 */
+
+	rmask = ch->ch_rsize - 1;
+
+	head = readw(&(bs->rx_head));
+	head &= rmask;
+	tail = readw(&(bs->rx_tail));
+	tail &= rmask;
+
+	data_len = (head - tail) & rmask;
+
+	if (data_len == 0) {
+		writeb(1, &(bs->idata));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		DPR_READ(("No data on port %d\n", ch->ch_portnum));
+		return;
+	}
+
+	/*
+	 * If the device is not open, or CREAD is off, flush
+	 * input data and return immediately.
+	 */
+	if ((bd->state != BOARD_READY) || !tp  || (tp->magic != TTY_MAGIC) ||
+            !(ch->ch_tun.un_flags & UN_ISOPEN) || !(tp->termios.c_cflag & CREAD) ||
+	    (ch->ch_tun.un_flags & UN_CLOSING)) {
+
+		DPR_READ(("input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum));
+		DPR_READ(("input. tp: %p tp->magic: %x MAGIC:%x ch flags: %x\n",
+			tp, tp ? tp->magic : 0, TTY_MAGIC, ch->ch_tun.un_flags));
+		writew(head, &(bs->rx_tail));
+		writeb(1, &(bs->idata));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return;
+	}
+
+	/*
+	 * If we are throttled, simply don't read any data.
+	 */
+	if (ch->ch_flags & CH_RXBLOCK) {
+		writeb(1, &(bs->idata));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		DPR_READ(("Port %d throttled, not reading any data. head: %x tail: %x\n",
+			ch->ch_portnum, head, tail));
+		return;
+	}
+
+	/*
+	 *      Ignore oruns.
+	 */
+	tmpchar = readb(&(bs->orun));
+	if (tmpchar) {
+		ch->ch_err_overrun++;
+		writeb(0, &(bs->orun));
+	}
+
+	DPR_READ(("dgap_input start 2\n"));
+
+	/* Decide how much data we can send into the tty layer */
+	flip_len = TTY_FLIPBUF_SIZE;
+
+	/* Chop down the length, if needed */
+	len = min(data_len, flip_len);
+	len = min(len, (N_TTY_BUF_SIZE - 1));
+
+	ld = tty_ldisc_ref(tp);
+                
+#ifdef TTY_DONT_FLIP
+	/*
+	 * If the DONT_FLIP flag is on, don't flush our buffer, and act
+	 * like the ld doesn't have any space to put the data right now.  
+	 */
+	if (test_bit(TTY_DONT_FLIP, &tp->flags))   
+		len = 0;
+#endif
+
+	/*
+	 * If we were unable to get a reference to the ld,
+	 * don't flush our buffer, and act like the ld doesn't
+	 * have any space to put the data right now.
+	 */
+	if (!ld) {
+		len = 0;
+	} else {
+		/*
+		 * If ld doesn't have a pointer to a receive_buf function,
+		 * flush the data, then act like the ld doesn't have any
+		 * space to put the data right now.
+		 */
+		if (!ld->ops->receive_buf) {
+			writew(head, &(bs->rx_tail));
+			len = 0;
+		}
+	}
+
+	if (len <= 0) {
+		writeb(1, &(bs->idata));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		DPR_READ(("dgap_input 1 - finish\n"));
+		if (ld)
+			tty_ldisc_deref(ld);
+		return;
+	}
+
+	buf = ch->ch_bd->flipbuf;
+	n = len;
+
+	/*
+	 * n now contains the most amount of data we can copy,
+	 * bounded either by our buffer size or the amount
+	 * of data the card actually has pending...
+	 */
+	while (n) {
+
+		s = ((head >= tail) ? head : ch->ch_rsize) - tail;
+		s = min(s, n);
+
+		if (s <= 0)
+			break;
+
+		memcpy_fromio(buf, (char *) ch->ch_raddr + tail, s);
+		dgap_sniff_nowait_nolock(ch, "USER READ", buf, s);
+
+		tail += s;
+		buf += s;
+
+		n -= s;
+		/* Flip queue if needed */
+		tail &= rmask;
+	}
+
+	writew(tail, &(bs->rx_tail));
+	writeb(1, &(bs->idata));
+	ch->ch_rxcount += len;
+
+	/*
+	 * If we are completely raw, we don't need to go through a lot
+	 * of the tty layers that exist.
+	 * In this case, we take the shortest and fastest route we
+	 * can to relay the data to the user.
+	 *
+	 * On the other hand, if we are not raw, we need to go through
+	 * the tty layer, which has its API more well defined.
+	 */
+	if (I_PARMRK(tp) || I_BRKINT(tp) || I_INPCK(tp)) {
+		dgap_parity_scan(ch, ch->ch_bd->flipbuf, ch->ch_bd->flipflagbuf, &len);
+
+		len = tty_buffer_request_room(tp->port, len);
+		tty_insert_flip_string_flags(tp->port, ch->ch_bd->flipbuf,
+			ch->ch_bd->flipflagbuf, len);
+	}
+	else {
+		len = tty_buffer_request_room(tp->port, len);
+		tty_insert_flip_string(tp->port, ch->ch_bd->flipbuf, len);
+	}
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	/* Tell the tty layer its okay to "eat" the data now */
+	tty_flip_buffer_push(tp->port);
+
+	if (ld)
+		tty_ldisc_deref(ld);
+
+	DPR_READ(("dgap_input - finish\n"));
+}
+
+
+/************************************************************************   
+ * Determines when CARRIER changes state and takes appropriate
+ * action. 
+ ************************************************************************/
+void dgap_carrier(struct channel_t *ch)
+{
+	struct board_t *bd;
+
+        int virt_carrier = 0;
+        int phys_carrier = 0;
+ 
+	DPR_CARR(("dgap_carrier called...\n"));
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	bd = ch->ch_bd;
+
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	/* Make sure altpin is always set correctly */
+	if (ch->ch_digi.digi_flags & DIGI_ALTPIN) {
+		ch->ch_dsr      = DM_CD;
+		ch->ch_cd       = DM_DSR;
+	}
+	else {
+		ch->ch_dsr      = DM_DSR;
+		ch->ch_cd       = DM_CD;
+	}
+
+	if (ch->ch_mistat & D_CD(ch)) {
+		DPR_CARR(("mistat: %x  D_CD: %x\n", ch->ch_mistat, D_CD(ch)));
+		phys_carrier = 1;
+	}
+
+	if (ch->ch_digi.digi_flags & DIGI_FORCEDCD) {
+		virt_carrier = 1;
+	}  
+
+	if (ch->ch_c_cflag & CLOCAL) {
+		virt_carrier = 1;
+	}  
+
+
+	DPR_CARR(("DCD: physical: %d virt: %d\n", phys_carrier, virt_carrier));
+
+	/*
+	 * Test for a VIRTUAL carrier transition to HIGH.
+	 */
+	if (((ch->ch_flags & CH_FCAR) == 0) && (virt_carrier == 1)) {
+
+		/*
+		 * When carrier rises, wake any threads waiting
+		 * for carrier in the open routine.
+		 */
+
+		DPR_CARR(("carrier: virt DCD rose\n"));
+
+		if (waitqueue_active(&(ch->ch_flags_wait)))
+			wake_up_interruptible(&ch->ch_flags_wait);
+	}
+
+	/*
+	 * Test for a PHYSICAL carrier transition to HIGH.
+	 */
+	if (((ch->ch_flags & CH_CD) == 0) && (phys_carrier == 1)) {
+
+		/*
+		 * When carrier rises, wake any threads waiting
+		 * for carrier in the open routine.
+		 */
+
+		DPR_CARR(("carrier: physical DCD rose\n"));
+
+		if (waitqueue_active(&(ch->ch_flags_wait)))
+			wake_up_interruptible(&ch->ch_flags_wait);
+	}
+
+	/*
+	 *  Test for a PHYSICAL transition to low, so long as we aren't
+	 *  currently ignoring physical transitions (which is what "virtual
+	 *  carrier" indicates).
+	 *
+	 *  The transition of the virtual carrier to low really doesn't
+	 *  matter... it really only means "ignore carrier state", not
+	 *  "make pretend that carrier is there".
+	 */
+	if ((virt_carrier == 0) && ((ch->ch_flags & CH_CD) != 0) &&
+	    (phys_carrier == 0)) 
+	{
+
+		/*
+		 *   When carrier drops:
+		 *
+		 *   Drop carrier on all open units.
+		 *
+		 *   Flush queues, waking up any task waiting in the
+		 *   line discipline.
+		 *
+		 *   Send a hangup to the control terminal.
+		 *
+		 *   Enable all select calls.
+		 */
+		if (waitqueue_active(&(ch->ch_flags_wait)))
+			wake_up_interruptible(&ch->ch_flags_wait);
+
+		if (ch->ch_tun.un_open_count > 0) {
+			DPR_CARR(("Sending tty hangup\n"));
+			tty_hangup(ch->ch_tun.un_tty);
+		}
+
+		if (ch->ch_pun.un_open_count > 0) { 
+			DPR_CARR(("Sending pr hangup\n"));
+			tty_hangup(ch->ch_pun.un_tty);
+		}
+	}
+
+	/*
+	 *  Make sure that our cached values reflect the current reality.
+	 */
+	if (virt_carrier == 1)
+		ch->ch_flags |= CH_FCAR;
+	else      
+		ch->ch_flags &= ~CH_FCAR;
+
+	if (phys_carrier == 1)
+		ch->ch_flags |= CH_CD;
+	else
+		ch->ch_flags &= ~CH_CD;
+}
+
+
+/************************************************************************
+ *      
+ * TTY Entry points and helper functions
+ *              
+ ************************************************************************/
+
+/*
+ * dgap_tty_open()
+ *
+ */
+static int dgap_tty_open(struct tty_struct *tty, struct file *file)
+{
+	struct board_t	*brd;
+	struct channel_t *ch;
+	struct un_t	*un;
+	struct bs_t	*bs;
+	uint		major = 0;
+	uint		minor = 0;
+	int		rc = 0;
+	ulong		lock_flags;
+	ulong		lock_flags2;
+	u16		head;
+
+	rc = 0;
+
+	major = MAJOR(tty_devnum(tty));
+	minor = MINOR(tty_devnum(tty));
+
+	if (major > 255) {
+		return -ENXIO;
+	}
+
+	/* Get board pointer from our array of majors we have allocated */
+	brd = dgap_BoardsByMajor[major];
+	if (!brd) {
+		return -ENXIO;
+	}
+
+	/*
+	 * If board is not yet up to a state of READY, go to
+	 * sleep waiting for it to happen or they cancel the open.
+	 */
+	rc = wait_event_interruptible(brd->state_wait,
+		(brd->state & BOARD_READY));
+
+	if (rc) {
+		return rc;
+	}
+
+	DGAP_LOCK(brd->bd_lock, lock_flags);
+
+	/* The wait above should guarantee this cannot happen */
+	if (brd->state != BOARD_READY) {
+		DGAP_UNLOCK(brd->bd_lock, lock_flags);
+		return -ENXIO;
+	}
+
+	/* If opened device is greater than our number of ports, bail. */
+	if (MINOR(tty_devnum(tty)) > brd->nasync) {
+		DGAP_UNLOCK(brd->bd_lock, lock_flags);
+		return -ENXIO;
+	}
+
+	ch = brd->channels[minor];
+	if (!ch) {
+		DGAP_UNLOCK(brd->bd_lock, lock_flags);
+		return -ENXIO;
+	}
+
+	/* Grab channel lock */
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	/* Figure out our type */
+	if (major == brd->dgap_Serial_Major) {
+		un = &brd->channels[minor]->ch_tun;
+		un->un_type = DGAP_SERIAL;
+	}
+	else if (major == brd->dgap_TransparentPrint_Major) {
+		un = &brd->channels[minor]->ch_pun;
+		un->un_type = DGAP_PRINT;
+	}
+	else {
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(brd->bd_lock, lock_flags);
+		DPR_OPEN(("%d Unknown TYPE!\n", __LINE__));
+		return -ENXIO;
+	}
+
+	/* Store our unit into driver_data, so we always have it available. */
+	tty->driver_data = un;
+
+	DPR_OPEN(("Open called. MAJOR: %d MINOR:%d unit: %p NAME: %s\n",
+		MAJOR(tty_devnum(tty)), MINOR(tty_devnum(tty)), un, brd->name));
+
+	/*
+	 * Error if channel info pointer is NULL.
+	 */
+	bs = ch->ch_bs;
+	if (!bs) {
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(brd->bd_lock, lock_flags);
+		DPR_OPEN(("%d BS is 0!\n", __LINE__));
+		return -ENXIO;
+        }
+
+	DPR_OPEN(("%d: tflag=%x  pflag=%x\n", __LINE__, ch->ch_tun.un_flags, ch->ch_pun.un_flags));
+
+	/*
+	 * Initialize tty's
+	 */
+	if (!(un->un_flags & UN_ISOPEN)) {
+		/* Store important variables. */
+		un->un_tty     = tty;
+
+		/* Maybe do something here to the TTY struct as well? */
+	}
+
+	/*
+	 * Initialize if neither terminal or printer is open.
+	 */
+	if (!((ch->ch_tun.un_flags | ch->ch_pun.un_flags) & UN_ISOPEN)) {
+
+		DPR_OPEN(("dgap_open: initializing channel in open...\n"));
+
+		ch->ch_mforce = 0;
+		ch->ch_mval = 0;
+
+		/*
+		 * Flush input queue.
+		 */
+		head = readw(&(bs->rx_head));
+		writew(head, &(bs->rx_tail));
+
+		ch->ch_flags = 0;
+		ch->pscan_state = 0;
+		ch->pscan_savechar = 0;
+
+		ch->ch_c_cflag   = tty->termios.c_cflag;
+		ch->ch_c_iflag   = tty->termios.c_iflag;
+		ch->ch_c_oflag   = tty->termios.c_oflag;
+		ch->ch_c_lflag   = tty->termios.c_lflag;
+		ch->ch_startc = tty->termios.c_cc[VSTART];
+		ch->ch_stopc  = tty->termios.c_cc[VSTOP];
+
+		/* TODO: flush our TTY struct here? */
+	}
+
+	dgap_carrier(ch);
+	/*
+	 * Run param in case we changed anything
+	 */
+	dgap_param(tty);
+
+	/*                              
+	 * follow protocol for opening port
+	 */
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(brd->bd_lock, lock_flags);
+
+	rc = dgap_block_til_ready(tty, file, ch);
+
+	if (!un->un_tty) {
+		return -ENODEV;
+	}
+
+	if (rc) {
+		DPR_OPEN(("dgap_tty_open returning after dgap_block_til_ready "
+			"with %d\n", rc));
+	}
+
+	/* No going back now, increment our unit and channel counters */
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+	ch->ch_open_count++;
+	un->un_open_count++;
+	un->un_flags |= (UN_ISOPEN);
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	DPR_OPEN(("dgap_tty_open finished\n"));
+	return (rc);
+}
+
+
+/*   
+ * dgap_block_til_ready()
+ *
+ * Wait for DCD, if needed.
+ */
+static int dgap_block_til_ready(struct tty_struct *tty, struct file *file, struct channel_t *ch)
+{ 
+	int retval = 0;
+	struct un_t *un = NULL;
+	ulong   lock_flags;
+	uint	old_flags = 0;
+	int sleep_on_un_flags = 0;
+
+	if (!tty || tty->magic != TTY_MAGIC || !file || !ch || ch->magic != DGAP_CHANNEL_MAGIC) {
+		return (-ENXIO);
+	}
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC) {
+		return (-ENXIO);
+	}
+
+	DPR_OPEN(("dgap_block_til_ready - before block.\n"));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	ch->ch_wopen++;
+
+	/* Loop forever */
+	while (1) {
+
+		sleep_on_un_flags = 0;
+
+		/*
+		 * If board has failed somehow during our sleep, bail with error.
+		 */
+		if (ch->ch_bd->state == BOARD_FAILED) {
+			retval = -ENXIO;
+			break;
+		}
+
+		/* If tty was hung up, break out of loop and set error. */
+		if (tty_hung_up_p(file)) {
+			retval = -EAGAIN;
+			break;
+		}
+
+		/*
+		 * If either unit is in the middle of the fragile part of close,
+		 * we just cannot touch the channel safely.
+		 * Go back to sleep, knowing that when the channel can be
+		 * touched safely, the close routine will signal the 
+		 * ch_wait_flags to wake us back up.
+		 */
+		if (!((ch->ch_tun.un_flags | ch->ch_pun.un_flags) & UN_CLOSING)) {
+
+			/*
+			 * Our conditions to leave cleanly and happily:
+			 * 1) NONBLOCKING on the tty is set.
+			 * 2) CLOCAL is set.
+			 * 3) DCD (fake or real) is active.
+			 */
+
+			if (file->f_flags & O_NONBLOCK) {
+				break;
+			}
+
+			if (tty->flags & (1 << TTY_IO_ERROR)) {
+				break;
+			}
+
+			if (ch->ch_flags & CH_CD) {
+				DPR_OPEN(("%d: ch_flags: %x\n", __LINE__, ch->ch_flags));
+				break;
+			}
+
+			if (ch->ch_flags & CH_FCAR) {
+				DPR_OPEN(("%d: ch_flags: %x\n", __LINE__, ch->ch_flags));
+				break;
+			}
+		}
+		else {
+			sleep_on_un_flags = 1;
+		}
+
+		/*
+		 * If there is a signal pending, the user probably
+		 * interrupted (ctrl-c) us.
+		 * Leave loop with error set.
+		 */
+		if (signal_pending(current)) {
+			DPR_OPEN(("%d: signal pending...\n", __LINE__));
+			retval = -ERESTARTSYS;
+			break;
+		}
+
+		DPR_OPEN(("dgap_block_til_ready - blocking.\n"));
+
+		/*
+		 * Store the flags before we let go of channel lock
+		 */
+		if (sleep_on_un_flags)
+			old_flags = ch->ch_tun.un_flags | ch->ch_pun.un_flags;
+		else
+			old_flags = ch->ch_flags;
+
+		/*
+		 * Let go of channel lock before calling schedule.
+		 * Our poller will get any FEP events and wake us up when DCD
+		 * eventually goes active.
+		 */
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+		DPR_OPEN(("Going to sleep on %s flags...\n",
+			(sleep_on_un_flags ? "un" : "ch")));
+
+		/*
+		 * Wait for something in the flags to change from the current value.
+		 */
+		if (sleep_on_un_flags) {
+			retval = wait_event_interruptible(un->un_flags_wait,
+				(old_flags != (ch->ch_tun.un_flags | ch->ch_pun.un_flags)));
+		}
+		else {
+			retval = wait_event_interruptible(ch->ch_flags_wait,
+				(old_flags != ch->ch_flags));
+		}
+
+		DPR_OPEN(("After sleep... retval: %x\n", retval));
+
+		/*
+		 * We got woken up for some reason.
+		 * Before looping around, grab our channel lock.
+		 */
+		DGAP_LOCK(ch->ch_lock, lock_flags);
+	}
+
+	ch->ch_wopen--;
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	DPR_OPEN(("dgap_block_til_ready - after blocking.\n"));
+
+	if (retval) {
+		DPR_OPEN(("dgap_block_til_ready - done. error. retval: %x\n", retval));
+		return(retval);
+	}
+
+	DPR_OPEN(("dgap_block_til_ready - done no error. jiffies: %lu\n", jiffies));
+
+	return(0);
+}
+
+
+/*
+ * dgap_tty_hangup()
+ *
+ * Hangup the port.  Like a close, but don't wait for output to drain.
+ */     
+static void dgap_tty_hangup(struct tty_struct *tty)
+{
+	struct board_t	*bd;
+	struct channel_t *ch;
+	struct un_t	*un;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_CLOSE(("dgap_hangup called. ch->ch_open_count: %d un->un_open_count: %d\n",
+		ch->ch_open_count, un->un_open_count));
+
+	/* flush the transmit queues */
+	dgap_tty_flush_buffer(tty);
+
+	DPR_CLOSE(("dgap_hangup finished. ch->ch_open_count: %d un->un_open_count: %d\n",
+		ch->ch_open_count, un->un_open_count));
+}
+
+
+
+/*
+ * dgap_tty_close()
+ *
+ */
+static void dgap_tty_close(struct tty_struct *tty, struct file *file)
+{
+	struct ktermios *ts;
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong lock_flags;
+	int rc = 0;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	ts = &tty->termios;
+
+	DPR_CLOSE(("Close called\n"));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	/*
+	 * Determine if this is the last close or not - and if we agree about
+	 * which type of close it is with the Line Discipline
+	 */
+	if ((tty->count == 1) && (un->un_open_count != 1)) {
+		/*
+		 * Uh, oh.  tty->count is 1, which means that the tty
+		 * structure will be freed.  un_open_count should always
+		 * be one in these conditions.  If it's greater than
+		 * one, we've got real problems, since it means the
+		 * serial port won't be shutdown.
+		 */
+		APR(("tty->count is 1, un open count is %d\n", un->un_open_count));
+		un->un_open_count = 1;
+	}  
+
+	if (--un->un_open_count < 0) {
+		APR(("bad serial port open count of %d\n", un->un_open_count));
+		un->un_open_count = 0;
+	}
+
+	ch->ch_open_count--;
+
+	if (ch->ch_open_count && un->un_open_count) {
+		DPR_CLOSE(("dgap_tty_close: not last close ch: %d un:%d\n",
+			ch->ch_open_count, un->un_open_count));
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+                return;
+        }
+
+	/* OK, its the last close on the unit */
+	DPR_CLOSE(("dgap_tty_close - last close on unit procedures\n"));
+
+	un->un_flags |= UN_CLOSING;
+
+	tty->closing = 1;
+
+	/*
+	 * Only officially close channel if count is 0 and
+         * DIGI_PRINTER bit is not set.
+	 */
+	if ((ch->ch_open_count == 0) && !(ch->ch_digi.digi_flags & DIGI_PRINTER)) {
+
+		ch->ch_flags &= ~(CH_RXBLOCK);
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+		/* wait for output to drain */
+		/* This will also return if we take an interrupt */
+
+		DPR_CLOSE(("Calling wait_for_drain\n"));
+		rc = dgap_wait_for_drain(tty);
+		DPR_CLOSE(("After calling wait_for_drain\n"));
+
+		if (rc) {
+			DPR_BASIC(("dgap_tty_close - bad return: %d ", rc));
+		}
+
+		dgap_tty_flush_buffer(tty);
+		tty_ldisc_flush(tty);
+
+		DGAP_LOCK(ch->ch_lock, lock_flags);
+
+		tty->closing = 0;
+
+		/*
+		 * If we have HUPCL set, lower DTR and RTS
+		 */
+		if (ch->ch_c_cflag & HUPCL ) {
+			DPR_CLOSE(("Close. HUPCL set, dropping DTR/RTS\n"));
+			ch->ch_mostat &= ~(D_RTS(ch)|D_DTR(ch));
+			dgap_cmdb( ch, SMODEM, 0, D_DTR(ch)|D_RTS(ch), 0 );
+
+			/*
+			 * Go to sleep to ensure RTS/DTR 
+			 * have been dropped for modems to see it.
+			 */
+			if (ch->ch_close_delay) {
+				DPR_CLOSE(("Close. Sleeping for RTS/DTR drop\n"));
+
+				DGAP_UNLOCK(ch->ch_lock, lock_flags);
+				dgap_ms_sleep(ch->ch_close_delay);
+				DGAP_LOCK(ch->ch_lock, lock_flags);
+
+				DPR_CLOSE(("Close. After sleeping for RTS/DTR drop\n"));
+			}
+		}
+
+		ch->pscan_state = 0;
+		ch->pscan_savechar = 0;
+		ch->ch_baud_info = 0;
+
+	}
+
+	/*
+	 * turn off print device when closing print device.
+	 */
+	if ((un->un_type == DGAP_PRINT)  && (ch->ch_flags & CH_PRON) ) {
+		dgap_wmove(ch, ch->ch_digi.digi_offstr,
+			(int) ch->ch_digi.digi_offlen);
+		ch->ch_flags &= ~CH_PRON;
+	}
+
+	un->un_tty = NULL;
+	un->un_flags &= ~(UN_ISOPEN | UN_CLOSING);
+	tty->driver_data = NULL;
+
+	DPR_CLOSE(("Close. Doing wakeups\n"));
+	wake_up_interruptible(&ch->ch_flags_wait);
+	wake_up_interruptible(&un->un_flags_wait);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+                
+        DPR_BASIC(("dgap_tty_close - complete\n"));
+}
+
+
+/*
+ * dgap_tty_chars_in_buffer()
+ *
+ * Return number of characters that have not been transmitted yet.
+ *
+ * This routine is used by the line discipline to determine if there
+ * is data waiting to be transmitted/drained/flushed or not.
+ */
+static int dgap_tty_chars_in_buffer(struct tty_struct *tty)
+{
+	struct board_t *bd = NULL;
+	struct channel_t *ch = NULL;
+	struct un_t *un = NULL;
+	struct bs_t *bs = NULL;
+	uchar tbusy;
+	uint chars = 0;
+	u16 thead, ttail, tmask, chead, ctail;
+	ulong   lock_flags = 0;
+	ulong   lock_flags2 = 0;
+
+	if (tty == NULL)
+		return(0);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+
+        bs = ch->ch_bs;
+	if (!bs)
+		return (0);
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	tmask = (ch->ch_tsize - 1);
+
+	/* Get Transmit queue pointers */
+	thead = readw(&(bs->tx_head)) & tmask;
+	ttail = readw(&(bs->tx_tail)) & tmask;
+
+	/* Get tbusy flag */
+	tbusy = readb(&(bs->tbusy));
+
+	/* Get Command queue pointers */
+	chead = readw(&(ch->ch_cm->cm_head));
+	ctail = readw(&(ch->ch_cm->cm_tail));
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	/*
+	 * The only way we know for sure if there is no pending
+	 * data left to be transferred, is if:
+	 * 1) Transmit head and tail are equal (empty).
+	 * 2) Command queue head and tail are equal (empty).
+	 * 3) The "TBUSY" flag is 0. (Transmitter not busy).
+ 	 */
+
+	if ((ttail == thead) && (tbusy == 0) && (chead == ctail)) {
+		chars = 0;
+	}
+	else {
+		if (thead >= ttail)
+			chars = thead - ttail;
+		else
+			chars = thead - ttail + ch->ch_tsize;
+		/*
+		 * Fudge factor here.
+		 * If chars is zero, we know that the command queue had
+		 * something in it or tbusy was set.  Because we cannot
+		 * be sure if there is still some data to be transmitted,
+		 * lets lie, and tell ld we have 1 byte left.
+		 */
+		if (chars == 0) {
+			/*
+			 * If TBUSY is still set, and our tx buffers are empty,
+			 * force the firmware to send me another wakeup after
+			 * TBUSY has been cleared.
+			 */
+			if (tbusy != 0) {
+				DGAP_LOCK(ch->ch_lock, lock_flags);
+				un->un_flags |= UN_EMPTY;
+				writeb(1, &(bs->iempty));
+				DGAP_UNLOCK(ch->ch_lock, lock_flags);
+			}
+			chars = 1;
+		}
+	}
+
+ 	DPR_WRITE(("dgap_tty_chars_in_buffer. Port: %x - %d (head: %d tail: %d tsize: %d)\n", 
+		ch->ch_portnum, chars, thead, ttail, ch->ch_tsize));
+        return(chars);
+}
+
+
+static int dgap_wait_for_drain(struct tty_struct *tty)
+{
+	struct channel_t *ch;
+	struct un_t *un;
+	struct bs_t *bs;
+	int ret = -EIO;
+	uint count = 1;
+	ulong   lock_flags = 0;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return ret;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return ret;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return ret;
+
+        bs = ch->ch_bs;
+	if (!bs)
+		return ret;
+
+	ret = 0;
+
+	DPR_DRAIN(("dgap_wait_for_drain start\n"));
+
+	/* Loop until data is drained */
+	while (count != 0) {
+
+		count = dgap_tty_chars_in_buffer(tty);
+
+		if (count == 0)
+			break;
+
+		/* Set flag waiting for drain */
+		DGAP_LOCK(ch->ch_lock, lock_flags);
+		un->un_flags |= UN_EMPTY;
+		writeb(1, &(bs->iempty));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+		/* Go to sleep till we get woken up */
+		ret = wait_event_interruptible(un->un_flags_wait, ((un->un_flags & UN_EMPTY) == 0));
+		/* If ret is non-zero, user ctrl-c'ed us */
+		if (ret) {
+			break;
+		}
+	}
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+	un->un_flags &= ~(UN_EMPTY);
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	DPR_DRAIN(("dgap_wait_for_drain finish\n"));
+	return (ret);
+}
+
+
+/*               
+ * dgap_maxcps_room
+ *
+ * Reduces bytes_available to the max number of characters
+ * that can be sent currently given the maxcps value, and
+ * returns the new bytes_available.  This only affects printer
+ * output.
+ */                     
+static int dgap_maxcps_room(struct tty_struct *tty, int bytes_available)
+{
+	struct channel_t *ch = NULL;
+	struct un_t *un = NULL;
+
+	if (tty == NULL)
+		return (bytes_available);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (bytes_available);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (bytes_available);
+
+	/*
+	 * If its not the Transparent print device, return
+	 * the full data amount.
+	 */
+	if (un->un_type != DGAP_PRINT)
+		return (bytes_available);
+
+	if (ch->ch_digi.digi_maxcps > 0 && ch->ch_digi.digi_bufsize > 0 ) {
+		int cps_limit = 0;
+		unsigned long current_time = jiffies;
+		unsigned long buffer_time = current_time +
+			(HZ * ch->ch_digi.digi_bufsize) / ch->ch_digi.digi_maxcps;
+
+		if (ch->ch_cpstime < current_time) {
+			/* buffer is empty */
+			ch->ch_cpstime = current_time;            /* reset ch_cpstime */
+			cps_limit = ch->ch_digi.digi_bufsize;
+		}
+		else if (ch->ch_cpstime < buffer_time) {
+			/* still room in the buffer */
+			cps_limit = ((buffer_time - ch->ch_cpstime) * ch->ch_digi.digi_maxcps) / HZ;
+		}
+		else {
+			/* no room in the buffer */
+			cps_limit = 0; 
+		}
+
+		bytes_available = min(cps_limit, bytes_available);
+	}
+
+	return (bytes_available);
+}
+
+
+static inline void dgap_set_firmware_event(struct un_t *un, unsigned int event)
+{
+	struct channel_t *ch = NULL;
+	struct bs_t *bs = NULL;
+
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+        bs = ch->ch_bs;
+	if (!bs)
+		return;
+
+	if ((event & UN_LOW) != 0) {
+		if ((un->un_flags & UN_LOW) == 0) {
+			un->un_flags |= UN_LOW;
+			writeb(1, &(bs->ilow));
+		}
+	}
+	if ((event & UN_LOW) != 0) {
+		if ((un->un_flags & UN_EMPTY) == 0) {
+			un->un_flags |= UN_EMPTY;
+			writeb(1, &(bs->iempty));
+		}
+	}
+}
+
+
+/*
+ * dgap_tty_write_room()
+ *
+ * Return space available in Tx buffer
+ */        
+static int dgap_tty_write_room(struct tty_struct *tty)
+{
+	struct channel_t *ch = NULL;
+	struct un_t *un = NULL;
+	struct bs_t *bs = NULL;
+	u16 head, tail, tmask;
+	int ret = 0;
+	ulong   lock_flags = 0;
+
+	if (tty == NULL || dgap_TmpWriteBuf == NULL)
+		return(0);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+
+        bs = ch->ch_bs;
+	if (!bs)
+		return (0);
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	tmask = ch->ch_tsize - 1;
+	head = readw(&(bs->tx_head)) & tmask;
+	tail = readw(&(bs->tx_tail)) & tmask;
+
+        if ((ret = tail - head - 1) < 0)
+                ret += ch->ch_tsize;
+
+	/* Limit printer to maxcps */
+	ret = dgap_maxcps_room(tty, ret);
+
+	/*
+	 * If we are printer device, leave space for 
+	 * possibly both the on and off strings.
+	 */
+	if (un->un_type == DGAP_PRINT) {
+		if (!(ch->ch_flags & CH_PRON))
+			ret -= ch->ch_digi.digi_onlen;
+		ret -= ch->ch_digi.digi_offlen;
+	}
+	else {
+		if (ch->ch_flags & CH_PRON)
+			ret -= ch->ch_digi.digi_offlen;
+	}
+
+	if (ret < 0)
+		ret = 0;
+
+	/*
+	 * Schedule FEP to wake us up if needed.
+	 *
+	 * TODO:  This might be overkill...
+	 * Do we really need to schedule callbacks from the FEP
+	 * in every case?  Can we get smarter based on ret?
+	 */
+	dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+ 
+	DPR_WRITE(("dgap_tty_write_room - %d tail: %d head: %d\n", ret, tail, head));
+
+        return(ret);
+}
+
+
+/*
+ * dgap_tty_put_char()
+ *
+ * Put a character into ch->ch_buf
+ *                              
+ *      - used by the line discipline for OPOST processing
+ */
+static int dgap_tty_put_char(struct tty_struct *tty, unsigned char c)
+{
+	/*
+	 * Simply call tty_write.
+	 */
+	DPR_WRITE(("dgap_tty_put_char called\n"));
+	dgap_tty_write(tty, &c, 1);
+	return 1;
+}
+
+
+/*
+ * dgap_tty_write()
+ *
+ * Take data from the user or kernel and send it out to the FEP.
+ * In here exists all the Transparent Print magic as well.
+ */
+static int dgap_tty_write(struct tty_struct *tty, const unsigned char *buf, int count)
+{
+	struct channel_t *ch = NULL;
+	struct un_t *un = NULL;
+	struct bs_t *bs = NULL;
+	char *vaddr = NULL;
+	u16 head, tail, tmask, remain;
+	int bufcount = 0, n = 0;
+	int orig_count = 0;
+	ulong lock_flags;
+	int from_user = 0;
+
+	if (tty == NULL || dgap_TmpWriteBuf == NULL)
+		return(0);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return(0);
+
+        bs = ch->ch_bs;
+	if (!bs)
+		return(0);
+
+	if (!count)
+		return(0);
+
+	DPR_WRITE(("dgap_tty_write: Port: %x tty=%p user=%d len=%d\n",
+		ch->ch_portnum, tty, from_user, count));
+
+	/*
+	 * Store original amount of characters passed in.
+	 * This helps to figure out if we should ask the FEP
+	 * to send us an event when it has more space available.
+	 */
+	orig_count = count;
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	/* Get our space available for the channel from the board */
+	tmask = ch->ch_tsize - 1;
+	head = readw(&(bs->tx_head)) & tmask;
+	tail = readw(&(bs->tx_tail)) & tmask;
+
+	if ((bufcount = tail - head - 1) < 0)
+		bufcount += ch->ch_tsize;
+
+	DPR_WRITE(("%d: bufcount: %x count: %x tail: %x head: %x tmask: %x\n",
+		__LINE__, bufcount, count, tail, head, tmask));
+
+	/*
+	 * Limit printer output to maxcps overall, with bursts allowed
+	 * up to bufsize characters.
+	 */
+	bufcount = dgap_maxcps_room(tty, bufcount);
+
+	/*
+	 * Take minimum of what the user wants to send, and the
+	 * space available in the FEP buffer.
+	 */
+	count = min(count, bufcount);
+
+	/*
+	 * Bail if no space left.
+	 */
+	if (count <= 0) {
+		dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+		return(0);
+	}
+
+	/*
+	 * Output the printer ON string, if we are in terminal mode, but
+	 * need to be in printer mode.
+	 */
+	if ((un->un_type == DGAP_PRINT) && !(ch->ch_flags & CH_PRON)) {
+		dgap_wmove(ch, ch->ch_digi.digi_onstr,
+		    (int) ch->ch_digi.digi_onlen);
+		head = readw(&(bs->tx_head)) & tmask;
+		ch->ch_flags |= CH_PRON;
+	}
+
+	/*
+	 * On the other hand, output the printer OFF string, if we are
+	 * currently in printer mode, but need to output to the terminal.
+	 */
+	if ((un->un_type != DGAP_PRINT) && (ch->ch_flags & CH_PRON)) {
+		dgap_wmove(ch, ch->ch_digi.digi_offstr,
+			(int) ch->ch_digi.digi_offlen);
+		head = readw(&(bs->tx_head)) & tmask;
+		ch->ch_flags &= ~CH_PRON;
+	}
+
+	/*
+	 * If there is nothing left to copy, or I can't handle any more data, leave.
+	 */
+	if (count <= 0) {
+		dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+		return(0);
+	}
+
+	if (from_user) {
+
+		count = min(count, WRITEBUFLEN);
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+		/*
+		 * If data is coming from user space, copy it into a temporary
+		 * buffer so we don't get swapped out while doing the copy to
+		 * the board.
+		 */
+		/* we're allowed to block if it's from_user */
+		if (down_interruptible(&dgap_TmpWriteSem)) {
+			return (-EINTR);
+		}
+
+		if (copy_from_user(dgap_TmpWriteBuf, (const uchar __user *) buf, count)) {
+			up(&dgap_TmpWriteSem);
+			printk("Write: Copy from user failed!\n");
+			return -EFAULT;
+		}
+
+		DGAP_LOCK(ch->ch_lock, lock_flags);
+
+		buf = dgap_TmpWriteBuf;
+	}
+
+	n = count;
+
+	/*
+	 * If the write wraps over the top of the circular buffer,
+	 * move the portion up to the wrap point, and reset the
+	 * pointers to the bottom.
+	 */
+	remain = ch->ch_tstart + ch->ch_tsize - head;
+
+	if (n >= remain) {
+		n -= remain;
+		vaddr = ch->ch_taddr + head;
+
+		memcpy_toio(vaddr, (uchar *) buf, remain);
+		dgap_sniff_nowait_nolock(ch, "USER WRITE", (uchar *) buf, remain);
+
+		head = ch->ch_tstart;
+		buf += remain;
+	}
+
+	if (n > 0) {
+
+		/*
+		 * Move rest of data.
+		 */
+		vaddr = ch->ch_taddr + head;
+		remain = n;
+
+		memcpy_toio(vaddr, (uchar *) buf, remain);
+		dgap_sniff_nowait_nolock(ch, "USER WRITE", (uchar *) buf, remain);
+
+		head += remain;
+
+	}
+
+	if (count) {
+		ch->ch_txcount += count;
+		head &= tmask;
+		writew(head, &(bs->tx_head));
+	}
+
+
+	dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
+
+	/*
+	 * If this is the print device, and the
+	 * printer is still on, we need to turn it
+	 * off before going idle.  If the buffer is
+	 * non-empty, wait until it goes empty.
+	 * Otherwise turn it off right now.
+	 */
+	if ((un->un_type == DGAP_PRINT) && (ch->ch_flags & CH_PRON)) {
+		tail = readw(&(bs->tx_tail)) & tmask;
+
+		if (tail != head) {
+			un->un_flags |= UN_EMPTY;
+			writeb(1, &(bs->iempty));
+		}
+		else {
+			dgap_wmove(ch, ch->ch_digi.digi_offstr,
+				(int) ch->ch_digi.digi_offlen);
+			head = readw(&(bs->tx_head)) & tmask;
+			ch->ch_flags &= ~CH_PRON;
+		}
+	}
+
+	/* Update printer buffer empty time. */
+	if ((un->un_type == DGAP_PRINT) && (ch->ch_digi.digi_maxcps > 0)
+	    && (ch->ch_digi.digi_bufsize > 0)) {
+                ch->ch_cpstime += (HZ * count) / ch->ch_digi.digi_maxcps;
+	}
+
+	if (from_user) {
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+		up(&dgap_TmpWriteSem);
+	} 
+	else {
+		DGAP_UNLOCK(ch->ch_lock, lock_flags);
+	}
+
+	DPR_WRITE(("Write finished - Write %d bytes of %d.\n", count, orig_count));
+
+	return (count);
+}
+
+
+
+/*
+ * Return modem signals to ld.
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39)
+static int dgap_tty_tiocmget(struct tty_struct *tty)
+#else
+static int dgap_tty_tiocmget(struct tty_struct *tty, struct file *file)
+#endif
+{
+	struct channel_t *ch;
+	struct un_t *un;
+	int result = -EIO;
+	uchar mstat = 0;
+	ulong lock_flags;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return result;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return result;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return result;
+
+	DPR_IOCTL(("dgap_tty_tiocmget start\n"));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	mstat = readb(&(ch->ch_bs->m_stat));
+        /* Append any outbound signals that might be pending... */
+        mstat |= ch->ch_mostat;
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	result = 0;
+
+	if (mstat & D_DTR(ch))
+		result |= TIOCM_DTR;
+	if (mstat & D_RTS(ch))
+		result |= TIOCM_RTS;
+	if (mstat & D_CTS(ch))
+		result |= TIOCM_CTS;
+	if (mstat & D_DSR(ch))
+		result |= TIOCM_DSR;
+	if (mstat & D_RI(ch))
+		result |= TIOCM_RI;
+	if (mstat & D_CD(ch))
+		result |= TIOCM_CD;
+
+	DPR_IOCTL(("dgap_tty_tiocmget finish\n"));
+
+	return result;
+}
+
+
+/*
+ * dgap_tty_tiocmset()
+ *
+ * Set modem signals, called by ld.
+ */
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39)
+static int dgap_tty_tiocmset(struct tty_struct *tty,
+                unsigned int set, unsigned int clear)
+#else
+static int dgap_tty_tiocmset(struct tty_struct *tty, struct file *file,
+		unsigned int set, unsigned int clear)
+#endif
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int ret = -EIO;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return ret;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return ret;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return ret;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return ret;
+
+	DPR_IOCTL(("dgap_tty_tiocmset start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	if (set & TIOCM_RTS) {
+		ch->ch_mforce |= D_RTS(ch);
+		ch->ch_mval   |= D_RTS(ch);
+        }         
+
+	if (set & TIOCM_DTR) {
+		ch->ch_mforce |= D_DTR(ch);
+		ch->ch_mval   |= D_DTR(ch);
+        }         
+
+	if (clear & TIOCM_RTS) {
+		ch->ch_mforce |= D_RTS(ch);
+		ch->ch_mval   &= ~(D_RTS(ch));
+        }
+
+	if (clear & TIOCM_DTR) {
+		ch->ch_mforce |= D_DTR(ch);
+		ch->ch_mval   &= ~(D_DTR(ch));
+        }
+
+	dgap_param(tty);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_tiocmset finish\n"));
+
+	return (0);
+}
+
+
+
+/*
+ * dgap_tty_send_break()
+ *
+ * Send a Break, called by ld.
+ */
+static int dgap_tty_send_break(struct tty_struct *tty, int msec)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int ret = -EIO;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return ret;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return ret;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return ret;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return ret;
+
+	switch (msec) {
+	case -1:
+		msec = 0xFFFF;
+		break;
+	case 0:
+		msec = 1;
+		break;
+	default:
+		msec /= 10;
+		break;
+	}
+
+	DPR_IOCTL(("dgap_tty_send_break start 1.  %lx\n", jiffies));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+#if 0
+	dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
+#endif
+	dgap_cmdw(ch, SBREAK, (u16) msec, 0);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_send_break finish\n"));
+
+	return (0);
+}
+
+
+
+
+/*
+ * dgap_tty_wait_until_sent()
+ *
+ * wait until data has been transmitted, called by ld.
+ */
+static void dgap_tty_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+	int rc;
+	rc = dgap_wait_for_drain(tty);
+	if (rc) {
+		DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+		return;
+	}
+	return;
+}
+
+
+
+/*
+ * dgap_send_xchar()
+ * 
+ * send a high priority character, called by ld.
+ */
+static void dgap_tty_send_xchar(struct tty_struct *tty, char c)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_send_xchar start 1.  %lx\n", jiffies));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	/*
+	 * This is technically what we should do.
+	 * However, the NIST tests specifically want
+	 * to see each XON or XOFF character that it
+	 * sends, so lets just send each character
+	 * by hand...
+	 */
+#if 0
+	if (c == STOP_CHAR(tty)) {
+		dgap_cmdw(ch, RPAUSE, 0, 0);
+	}
+	else if (c == START_CHAR(tty)) {
+		dgap_cmdw(ch, RRESUME, 0, 0);
+	}
+	else {
+		dgap_wmove(ch, &c, 1);
+	}
+#else
+	dgap_wmove(ch, &c, 1);
+#endif
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_send_xchar finish\n"));
+
+	return;
+}
+
+
+
+
+/*
+ * Return modem signals to ld.
+ */
+static int dgap_get_modem_info(struct channel_t *ch, unsigned int __user *value)
+{
+	int result = 0;
+	uchar mstat = 0;
+	ulong lock_flags;
+	int rc = 0;
+
+	DPR_IOCTL(("dgap_get_modem_info start\n"));
+
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return(-ENXIO);
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+
+	mstat = readb(&(ch->ch_bs->m_stat));
+	/* Append any outbound signals that might be pending... */
+	mstat |= ch->ch_mostat;
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	result = 0;
+
+	if (mstat & D_DTR(ch))
+		result |= TIOCM_DTR;
+	if (mstat & D_RTS(ch))
+		result |= TIOCM_RTS;
+	if (mstat & D_CTS(ch))
+		result |= TIOCM_CTS;
+	if (mstat & D_DSR(ch))
+		result |= TIOCM_DSR;
+	if (mstat & D_RI(ch))
+		result |= TIOCM_RI;
+	if (mstat & D_CD(ch))
+		result |= TIOCM_CD;
+
+	rc = put_user(result, value);
+
+	DPR_IOCTL(("dgap_get_modem_info finish\n"));
+	return(rc);
+}
+
+
+/*
+ * dgap_set_modem_info()
+ *
+ * Set modem signals, called by ld.
+ */
+static int dgap_set_modem_info(struct tty_struct *tty, unsigned int command, unsigned int __user *value)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int ret = -ENXIO;
+	unsigned int arg = 0;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return ret;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return ret;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return ret;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return ret;
+
+	DPR_IOCTL(("dgap_set_modem_info() start\n"));
+
+	ret = get_user(arg, value);
+	if (ret) {
+		DPR_IOCTL(("dgap_set_modem_info %d ret: %x. finished.\n", __LINE__, ret));
+		return(ret);
+	}
+
+	DPR_IOCTL(("dgap_set_modem_info: command: %x arg: %x\n", command, arg));
+
+	switch (command) {
+	case TIOCMBIS:
+		if (arg & TIOCM_RTS) {
+			ch->ch_mforce |= D_RTS(ch);
+			ch->ch_mval   |= D_RTS(ch);
+        	}
+
+		if (arg & TIOCM_DTR) {
+			ch->ch_mforce |= D_DTR(ch);
+			ch->ch_mval   |= D_DTR(ch);
+        	}
+
+		break;
+
+	case TIOCMBIC:
+		if (arg & TIOCM_RTS) {
+			ch->ch_mforce |= D_RTS(ch);
+			ch->ch_mval   &= ~(D_RTS(ch));
+        	}
+
+		if (arg & TIOCM_DTR) {
+			ch->ch_mforce |= D_DTR(ch);
+			ch->ch_mval   &= ~(D_DTR(ch));
+        	}
+
+		break;
+
+        case TIOCMSET:
+		ch->ch_mforce = D_DTR(ch)|D_RTS(ch);
+
+		if (arg & TIOCM_RTS) {
+			ch->ch_mval |= D_RTS(ch);
+        	}
+		else {
+			ch->ch_mval &= ~(D_RTS(ch));
+		}
+
+		if (arg & TIOCM_DTR) {
+			ch->ch_mval |= (D_DTR(ch));
+        	}
+		else {
+			ch->ch_mval &= ~(D_DTR(ch));
+		}
+
+		break;
+
+	default:
+		return(-EINVAL);
+	}
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	dgap_param(tty);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_set_modem_info finish\n"));
+
+	return (0);
+}
+
+
+/*
+ * dgap_tty_digigeta() 
+ *
+ * Ioctl to get the information for ditty.
+ *
+ *
+ *
+ */
+static int dgap_tty_digigeta(struct tty_struct *tty, struct digi_t __user *retinfo)
+{
+	struct channel_t *ch;
+	struct un_t *un;
+	struct digi_t tmp;
+	ulong lock_flags;
+
+	if (!retinfo)
+		return (-EFAULT);
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	memset(&tmp, 0, sizeof(tmp));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+	memcpy(&tmp, &ch->ch_digi, sizeof(tmp));
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+		return (-EFAULT);
+
+	return (0);
+}
+
+
+/*
+ * dgap_tty_digiseta() 
+ *
+ * Ioctl to set the information for ditty.
+ *
+ *
+ *
+ */
+static int dgap_tty_digiseta(struct tty_struct *tty, struct digi_t __user *new_info)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	struct digi_t new_digi;
+	ulong   lock_flags = 0;
+	unsigned long lock_flags2;
+
+	DPR_IOCTL(("DIGI_SETA start\n"));
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (-EFAULT);
+
+        if (copy_from_user(&new_digi, new_info, sizeof(struct digi_t))) {
+		DPR_IOCTL(("DIGI_SETA failed copy_from_user\n"));
+                return(-EFAULT);
+	}
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	memcpy(&ch->ch_digi, &new_digi, sizeof(struct digi_t));
+
+	if (ch->ch_digi.digi_maxcps < 1) 
+		ch->ch_digi.digi_maxcps = 1;
+
+	if (ch->ch_digi.digi_maxcps > 10000) 
+		ch->ch_digi.digi_maxcps = 10000;
+
+	if (ch->ch_digi.digi_bufsize < 10)
+		ch->ch_digi.digi_bufsize = 10;
+
+	if (ch->ch_digi.digi_maxchar < 1)
+		ch->ch_digi.digi_maxchar = 1;
+
+	if (ch->ch_digi.digi_maxchar > ch->ch_digi.digi_bufsize)
+		ch->ch_digi.digi_maxchar = ch->ch_digi.digi_bufsize;
+
+	if (ch->ch_digi.digi_onlen > DIGI_PLEN)
+		ch->ch_digi.digi_onlen = DIGI_PLEN;
+
+	if (ch->ch_digi.digi_offlen > DIGI_PLEN)
+		ch->ch_digi.digi_offlen = DIGI_PLEN;
+
+	dgap_param(tty);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("DIGI_SETA finish\n"));
+
+	return(0);
+}
+
+
+/*
+ * dgap_tty_digigetedelay() 
+ *
+ * Ioctl to get the current edelay setting.
+ *
+ *
+ *
+ */
+static int dgap_tty_digigetedelay(struct tty_struct *tty, int __user *retinfo)
+{
+	struct channel_t *ch;
+	struct un_t *un;
+	int tmp;
+	ulong lock_flags;
+
+	if (!retinfo)
+		return (-EFAULT);
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	memset(&tmp, 0, sizeof(tmp));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+	tmp = readw(&(ch->ch_bs->edelay));
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+		return (-EFAULT);
+
+	return (0);
+}
+
+
+/*
+ * dgap_tty_digisetedelay() 
+ *
+ * Ioctl to set the EDELAY setting
+ *
+ */
+static int dgap_tty_digisetedelay(struct tty_struct *tty, int __user *new_info)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int new_digi;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	DPR_IOCTL(("DIGI_SETA start\n"));
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (-EFAULT);
+
+        if (copy_from_user(&new_digi, new_info, sizeof(int))) {
+		DPR_IOCTL(("DIGI_SETEDELAY failed copy_from_user\n"));
+                return(-EFAULT);
+	}
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	writew((u16) new_digi, &(ch->ch_bs->edelay));
+
+	dgap_param(tty);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("DIGI_SETA finish\n"));
+
+	return(0);
+}
+
+
+/*
+ * dgap_tty_digigetcustombaud()
+ *
+ * Ioctl to get the current custom baud rate setting.
+ */
+static int dgap_tty_digigetcustombaud(struct tty_struct *tty, int __user *retinfo)
+{
+	struct channel_t *ch;
+	struct un_t *un;
+	int tmp;
+	ulong lock_flags;
+
+	if (!retinfo)
+		return (-EFAULT);
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	memset(&tmp, 0, sizeof(tmp));
+
+	DGAP_LOCK(ch->ch_lock, lock_flags);
+	tmp = dgap_get_custom_baud(ch);
+	DGAP_UNLOCK(ch->ch_lock, lock_flags);
+
+	DPR_IOCTL(("DIGI_GETCUSTOMBAUD. Returning %d\n", tmp));
+
+	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+		return (-EFAULT);
+
+	return (0);
+}
+
+
+/*
+ * dgap_tty_digisetcustombaud() 
+ *
+ * Ioctl to set the custom baud rate setting
+ */
+static int dgap_tty_digisetcustombaud(struct tty_struct *tty, int __user *new_info)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	uint new_rate;
+	ulong lock_flags;
+	ulong lock_flags2;
+
+	DPR_IOCTL(("DIGI_SETCUSTOMBAUD start\n"));
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-EFAULT);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-EFAULT);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-EFAULT);
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (-EFAULT);
+
+
+	if (copy_from_user(&new_rate, new_info, sizeof(unsigned int))) {
+		DPR_IOCTL(("DIGI_SETCUSTOMBAUD failed copy_from_user\n"));
+		return(-EFAULT);
+	}
+
+	if (bd->bd_flags & BD_FEP5PLUS) {
+
+		DPR_IOCTL(("DIGI_SETCUSTOMBAUD. Setting %d\n", new_rate));
+
+		DGAP_LOCK(bd->bd_lock, lock_flags);
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+		ch->ch_custom_speed = new_rate;
+
+		dgap_param(tty);
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+	}
+
+	DPR_IOCTL(("DIGI_SETCUSTOMBAUD finish\n"));
+
+	return(0);
+}
+
+
+/*
+ * dgap_set_termios()
+ */
+static void dgap_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	unsigned long lock_flags;
+	unsigned long lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	ch->ch_c_cflag   = tty->termios.c_cflag;
+	ch->ch_c_iflag   = tty->termios.c_iflag;
+	ch->ch_c_oflag   = tty->termios.c_oflag;
+	ch->ch_c_lflag   = tty->termios.c_lflag;
+	ch->ch_startc    = tty->termios.c_cc[VSTART];
+	ch->ch_stopc     = tty->termios.c_cc[VSTOP];
+
+	dgap_carrier(ch);
+	dgap_param(tty);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+}
+
+
+static void dgap_tty_throttle(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_throttle start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	ch->ch_flags |= (CH_RXBLOCK);
+#if 1
+	dgap_cmdw(ch, RPAUSE, 0, 0);
+#endif
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_throttle finish\n"));
+}
+
+
+static void dgap_tty_unthrottle(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_unthrottle start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	ch->ch_flags &= ~(CH_RXBLOCK);
+
+#if 1
+	dgap_cmdw(ch, RRESUME, 0, 0);
+#endif
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_unthrottle finish\n"));
+}
+
+
+static void dgap_tty_start(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_start start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	dgap_cmdw(ch, RESUMETX, 0, 0);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_start finish\n"));
+}
+
+
+static void dgap_tty_stop(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_stop start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	dgap_cmdw(ch, PAUSETX, 0, 0);
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_stop finish\n"));
+}
+
+
+/* 
+ * dgap_tty_flush_chars()
+ *
+ * Flush the cook buffer
+ *
+ * Note to self, and any other poor souls who venture here:
+ *
+ * flush in this case DOES NOT mean dispose of the data.
+ * instead, it means "stop buffering and send it if you
+ * haven't already."  Just guess how I figured that out...   SRW 2-Jun-98
+ *
+ * It is also always called in interrupt context - JAR 8-Sept-99
+ */
+static void dgap_tty_flush_chars(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_flush_chars start\n"));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	/* TODO: Do something here */
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+	DPR_IOCTL(("dgap_tty_flush_chars finish\n"));
+}
+
+
+
+/*
+ * dgap_tty_flush_buffer()
+ *              
+ * Flush Tx buffer (make in == out)
+ */
+static void dgap_tty_flush_buffer(struct tty_struct *tty)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	ulong   lock_flags;
+	ulong   lock_flags2;
+	u16	head = 0;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return;
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return;
+        
+        ch = un->un_ch;
+        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+                return;
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return;
+
+	DPR_IOCTL(("dgap_tty_flush_buffer on port: %d start\n", ch->ch_portnum));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	ch->ch_flags &= ~CH_STOP;
+	head = readw(&(ch->ch_bs->tx_head));
+	dgap_cmdw(ch, FLUSHTX, (u16) head, 0);
+	dgap_cmdw(ch, RESUMETX, 0, 0);
+	if (ch->ch_tun.un_flags & (UN_LOW|UN_EMPTY)) {
+		ch->ch_tun.un_flags &= ~(UN_LOW|UN_EMPTY);
+		wake_up_interruptible(&ch->ch_tun.un_flags_wait);
+	}
+	if (ch->ch_pun.un_flags & (UN_LOW|UN_EMPTY)) {
+		ch->ch_pun.un_flags &= ~(UN_LOW|UN_EMPTY);
+		wake_up_interruptible(&ch->ch_pun.un_flags_wait);
+	}
+
+	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+	DGAP_UNLOCK(bd->bd_lock, lock_flags);
+	if (waitqueue_active(&tty->write_wait))
+		wake_up_interruptible(&tty->write_wait);
+	tty_wakeup(tty);
+
+	DPR_IOCTL(("dgap_tty_flush_buffer finish\n"));
+}
+
+
+
+/*****************************************************************************
+ *
+ * The IOCTL function and all of its helpers
+ *
+ *****************************************************************************/
+                        
+/*
+ * dgap_tty_ioctl()
+ *
+ * The usual assortment of ioctl's
+ */
+static int dgap_tty_ioctl(struct tty_struct *tty, unsigned int cmd,
+		unsigned long arg)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int rc;
+	u16	head = 0;
+	ulong   lock_flags = 0;
+	ulong   lock_flags2 = 0;
+	void __user *uarg = (void __user *) arg;
+
+	if (!tty || tty->magic != TTY_MAGIC)
+		return (-ENODEV);
+
+	un = tty->driver_data;
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (-ENODEV);
+
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (-ENODEV);
+
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (-ENODEV);
+
+	DPR_IOCTL(("dgap_tty_ioctl start on port %d - cmd %s (%x), arg %lx\n", 
+		ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+	DGAP_LOCK(bd->bd_lock, lock_flags);
+	DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+	if (un->un_open_count <= 0) {
+		DPR_BASIC(("dgap_tty_ioctl - unit not open.\n"));
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(-EIO);
+	}
+
+	switch (cmd) {
+
+	/* Here are all the standard ioctl's that we MUST implement */
+
+	case TCSBRK:
+		/*
+		 * TCSBRK is SVID version: non-zero arg --> no break  
+		 * this behaviour is exploited by tcdrain().
+		 *
+		 * According to POSIX.1 spec (7.2.2.1.2) breaks should be
+		 * between 0.25 and 0.5 seconds so we'll ask for something
+		 * in the middle: 0.375 seconds.
+		 */
+		rc = tty_check_change(tty);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		if (rc) {
+			return(rc);
+		}
+
+		rc = dgap_wait_for_drain(tty);
+
+		if (rc) {
+			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+			return(-EINTR);
+		}
+
+		DGAP_LOCK(bd->bd_lock, lock_flags);
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+		if(((cmd == TCSBRK) && (!arg)) || (cmd == TCSBRKP)) {
+			dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
+		}
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
+			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+                return(0);
+
+
+	case TCSBRKP:
+ 		/* support for POSIX tcsendbreak()
+
+		 * According to POSIX.1 spec (7.2.2.1.2) breaks should be
+		 * between 0.25 and 0.5 seconds so we'll ask for something
+		 * in the middle: 0.375 seconds.
+		 */
+		rc = tty_check_change(tty);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		if (rc) {
+			return(rc);
+		}
+
+		rc = dgap_wait_for_drain(tty);
+		if (rc) {
+			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+			return(-EINTR);
+		}
+
+		DGAP_LOCK(bd->bd_lock, lock_flags);
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+		dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
+			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+		return(0);
+
+        case TIOCSBRK:
+		/*
+		 * FEP5 doesn't support turning on a break unconditionally.
+		 * The FEP5 device will stop sending a break automatically
+		 * after the specified time value that was sent when turning on
+		 * the break.
+		 */
+		rc = tty_check_change(tty);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		if (rc) {
+			return(rc);
+		}
+
+		rc = dgap_wait_for_drain(tty);
+		if (rc) {
+			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+			return(-EINTR);
+		}
+
+		DGAP_LOCK(bd->bd_lock, lock_flags);
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+
+		dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
+			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+		return 0;
+                
+        case TIOCCBRK:
+		/*
+		 * FEP5 doesn't support turning off a break unconditionally.
+		 * The FEP5 device will stop sending a break automatically
+		 * after the specified time value that was sent when turning on
+		 * the break.
+		 */
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return 0;
+
+	case TIOCGSOFTCAR:
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		rc = put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *) arg);
+		return(rc);
+
+	case TIOCSSOFTCAR:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		rc = get_user(arg, (unsigned long __user *) arg);
+		if (rc)
+			return(rc);
+
+		DGAP_LOCK(bd->bd_lock, lock_flags);
+		DGAP_LOCK(ch->ch_lock, lock_flags2);
+		tty->termios.c_cflag = ((tty->termios.c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
+		dgap_param(tty);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		return(0);
+                        
+	case TIOCMGET:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+                return(dgap_get_modem_info(ch, uarg));
+
+	case TIOCMBIS:
+	case TIOCMBIC:
+	case TIOCMSET:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_set_modem_info(tty, cmd, uarg));
+
+		/*
+		 * Here are any additional ioctl's that we want to implement
+		 */
+                        
+	case TCFLSH:  
+		/*
+		 * The linux tty driver doesn't have a flush
+		 * input routine for the driver, assuming all backed
+		 * up data is in the line disc. buffers.  However,
+		 * we all know that's not the case.  Here, we
+		 * act on the ioctl, but then lie and say we didn't
+		 * so the line discipline will process the flush
+		 * also.
+		 */   
+		rc = tty_check_change(tty);
+		if (rc) {
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			return(rc);
+		}
+
+		if ((arg == TCIFLUSH) || (arg == TCIOFLUSH)) {
+			if (!(un->un_type == DGAP_PRINT)) {
+				head = readw(&(ch->ch_bs->rx_head));
+				writew(head, &(ch->ch_bs->rx_tail));
+				writeb(0, &(ch->ch_bs->orun));
+			}
+		}
+
+		if ((arg == TCOFLUSH) || (arg == TCIOFLUSH)) {
+			ch->ch_flags &= ~CH_STOP;
+			head = readw(&(ch->ch_bs->tx_head));
+			dgap_cmdw(ch, FLUSHTX, (u16) head, 0 );
+			dgap_cmdw(ch, RESUMETX, 0, 0);
+			if (ch->ch_tun.un_flags & (UN_LOW|UN_EMPTY)) {
+				ch->ch_tun.un_flags &= ~(UN_LOW|UN_EMPTY);
+				wake_up_interruptible(&ch->ch_tun.un_flags_wait);
+			}
+			if (ch->ch_pun.un_flags & (UN_LOW|UN_EMPTY)) {
+				ch->ch_pun.un_flags &= ~(UN_LOW|UN_EMPTY);
+				wake_up_interruptible(&ch->ch_pun.un_flags_wait);
+			}
+			if (waitqueue_active(&tty->write_wait))
+				wake_up_interruptible(&tty->write_wait);
+
+			/* Can't hold any locks when calling tty_wakeup! */
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			tty_wakeup(tty);
+			DGAP_LOCK(bd->bd_lock, lock_flags);
+			DGAP_LOCK(ch->ch_lock, lock_flags2);
+		}                  
+
+		/* pretend we didn't recognize this IOCTL */  
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		DPR_IOCTL(("dgap_tty_ioctl (LINE:%d) finish on port %d - cmd %s (%x), arg %lx\n", 
+			__LINE__, ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+		return(-ENOIOCTLCMD);
+
+	case TCSETSF:
+	case TCSETSW:
+		/*
+		 * The linux tty driver doesn't have a flush
+		 * input routine for the driver, assuming all backed
+		 * up data is in the line disc. buffers.  However,
+		 * we all know that's not the case.  Here, we
+		 * act on the ioctl, but then lie and say we didn't
+		 * so the line discipline will process the flush
+		 * also.
+		 */
+		if (cmd == TCSETSF) {
+			/* flush rx */
+			ch->ch_flags &= ~CH_STOP;
+			head = readw(&(ch->ch_bs->rx_head));
+			writew(head, &(ch->ch_bs->rx_tail));
+		}
+
+		/* now wait for all the output to drain */
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		rc = dgap_wait_for_drain(tty);
+		if (rc) {
+			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+			return(-EINTR);
+		}
+
+		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
+			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
+
+		/* pretend we didn't recognize this */
+		return(-ENOIOCTLCMD);
+
+	case TCSETAW:
+
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		rc = dgap_wait_for_drain(tty);
+		if (rc) {
+			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+			return(-EINTR);
+		}
+
+		/* pretend we didn't recognize this */
+		return(-ENOIOCTLCMD);  
+
+	case TCXONC:
+		/*
+		 * The Linux Line Discipline (LD) would do this for us if we
+		 * let it, but we have the special firmware options to do this
+		 * the "right way" regardless of hardware or software flow
+		 * control so we'll do it outselves instead of letting the LD
+		 * do it.
+		 */
+		rc = tty_check_change(tty);
+		if (rc) {
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			return(rc);
+		}
+
+		DPR_IOCTL(("dgap_ioctl - in TCXONC - %d\n", cmd));
+		switch (arg) {
+
+		case TCOON:
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			dgap_tty_start(tty);
+			return(0);
+		case TCOOFF:
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			dgap_tty_stop(tty);
+			return(0);
+		case TCION:
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			/* Make the ld do it */
+			return(-ENOIOCTLCMD);
+		case TCIOFF:
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			/* Make the ld do it */
+			return(-ENOIOCTLCMD);
+		default:
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			return(-EINVAL);
+		}
+
+	case DIGI_GETA:
+		/* get information for ditty */
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digigeta(tty, uarg));
+
+	case DIGI_SETAW:
+	case DIGI_SETAF:
+
+		/* set information for ditty */
+		if (cmd == (DIGI_SETAW)) {
+
+			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+			DGAP_UNLOCK(bd->bd_lock, lock_flags);
+			rc = dgap_wait_for_drain(tty);
+			if (rc) {
+				DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
+				return(-EINTR);
+			}
+			DGAP_LOCK(bd->bd_lock, lock_flags);
+			DGAP_LOCK(ch->ch_lock, lock_flags2);
+		}
+		else {
+			tty_ldisc_flush(tty);
+		}
+		/* fall thru */
+
+	case DIGI_SETA:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digiseta(tty, uarg));
+
+	case DIGI_GEDELAY:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digigetedelay(tty, uarg));
+
+	case DIGI_SEDELAY:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digisetedelay(tty, uarg));
+
+	case DIGI_GETCUSTOMBAUD:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digigetcustombaud(tty, uarg));
+
+	case DIGI_SETCUSTOMBAUD:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return(dgap_tty_digisetcustombaud(tty, uarg));
+
+	case DIGI_RESET_PORT:
+		dgap_firmware_reset_port(ch);
+		dgap_param(tty);
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+		return 0;
+
+	default:
+		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
+		DGAP_UNLOCK(bd->bd_lock, lock_flags);
+
+		DPR_IOCTL(("dgap_tty_ioctl - in default\n"));
+		DPR_IOCTL(("dgap_tty_ioctl end - cmd %s (%x), arg %lx\n", 
+			dgap_ioctl_name(cmd), cmd, arg));
+
+		return(-ENOIOCTLCMD);
+	}
+}
+static ssize_t dgap_driver_version_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%s\n", DG_PART);
+}
+static DRIVER_ATTR(version, S_IRUSR, dgap_driver_version_show, NULL);
+
+
+static ssize_t dgap_driver_boards_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%d\n", dgap_NumBoards);
+}
+static DRIVER_ATTR(boards, S_IRUSR, dgap_driver_boards_show, NULL);
+
+
+static ssize_t dgap_driver_maxboards_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%d\n", MAXBOARDS);
+}
+static DRIVER_ATTR(maxboards, S_IRUSR, dgap_driver_maxboards_show, NULL);
+
+
+static ssize_t dgap_driver_pollcounter_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%ld\n", dgap_poll_counter);
+}
+static DRIVER_ATTR(pollcounter, S_IRUSR, dgap_driver_pollcounter_show, NULL);
+
+
+static ssize_t dgap_driver_state_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%s\n", dgap_driver_state_text[dgap_driver_state]);
+}
+static DRIVER_ATTR(state, S_IRUSR, dgap_driver_state_show, NULL);
+
+
+static ssize_t dgap_driver_debug_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "0x%x\n", dgap_debug);
+}
+
+static ssize_t dgap_driver_debug_store(struct device_driver *ddp, const char *buf, size_t count)
+{
+	sscanf(buf, "0x%x\n", &dgap_debug);
+	return count;
+}
+static DRIVER_ATTR(debug, (S_IRUSR | S_IWUSR), dgap_driver_debug_show, dgap_driver_debug_store);
+
+
+static ssize_t dgap_driver_rawreadok_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "0x%x\n", dgap_rawreadok);
+}
+
+static ssize_t dgap_driver_rawreadok_store(struct device_driver *ddp, const char *buf, size_t count)
+{
+	sscanf(buf, "0x%x\n", &dgap_rawreadok);
+	return count;
+}
+static DRIVER_ATTR(rawreadok, (S_IRUSR | S_IWUSR), dgap_driver_rawreadok_show, dgap_driver_rawreadok_store);
+
+
+static ssize_t dgap_driver_pollrate_show(struct device_driver *ddp, char *buf)
+{
+	return snprintf(buf, PAGE_SIZE, "%dms\n", dgap_poll_tick);
+}
+
+static ssize_t dgap_driver_pollrate_store(struct device_driver *ddp, const char *buf, size_t count)
+{
+	sscanf(buf, "%d\n", &dgap_poll_tick);
+	return count;
+}
+static DRIVER_ATTR(pollrate, (S_IRUSR | S_IWUSR), dgap_driver_pollrate_show, dgap_driver_pollrate_store);
+
+
+static void dgap_create_driver_sysfiles(struct pci_driver *dgap_driver)
+{
+	int rc = 0;
+	struct device_driver *driverfs = &dgap_driver->driver;
+
+	rc |= driver_create_file(driverfs, &driver_attr_version);
+	rc |= driver_create_file(driverfs, &driver_attr_boards);
+	rc |= driver_create_file(driverfs, &driver_attr_maxboards);
+	rc |= driver_create_file(driverfs, &driver_attr_debug);
+	rc |= driver_create_file(driverfs, &driver_attr_rawreadok); 
+	rc |= driver_create_file(driverfs, &driver_attr_pollrate);
+	rc |= driver_create_file(driverfs, &driver_attr_pollcounter);
+	rc |= driver_create_file(driverfs, &driver_attr_state);
+	if (rc) {
+		printk(KERN_ERR "DGAP: sysfs driver_create_file failed!\n");
+	}
+}
+
+
+static void dgap_remove_driver_sysfiles(struct pci_driver *dgap_driver)
+{
+	struct device_driver *driverfs = &dgap_driver->driver;
+	driver_remove_file(driverfs, &driver_attr_version);
+	driver_remove_file(driverfs, &driver_attr_boards);
+	driver_remove_file(driverfs, &driver_attr_maxboards);
+	driver_remove_file(driverfs, &driver_attr_debug);
+	driver_remove_file(driverfs, &driver_attr_rawreadok);
+	driver_remove_file(driverfs, &driver_attr_pollrate);
+	driver_remove_file(driverfs, &driver_attr_pollcounter);
+	driver_remove_file(driverfs, &driver_attr_state);
+}
+
+
+#define DGAP_VERIFY_BOARD(p, bd)			\
+	if (!p)						\
+		return (0);				\
+							\
+	bd = dev_get_drvdata(p);			\
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)	\
+		return (0);				\
+	if (bd->state != BOARD_READY)			\
+		return (0);				\
+
+
+static ssize_t dgap_ports_state_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count,
+			"%d %s\n", bd->channels[i]->ch_portnum,
+			bd->channels[i]->ch_open_count ? "Open" : "Closed");
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_state, S_IRUSR, dgap_ports_state_show, NULL);
+
+
+static ssize_t dgap_ports_baud_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count +=  snprintf(buf + count, PAGE_SIZE - count,
+			"%d %d\n", bd->channels[i]->ch_portnum, bd->channels[i]->ch_baud_info);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_baud, S_IRUSR, dgap_ports_baud_show, NULL);
+
+
+static ssize_t dgap_ports_msignals_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		if (bd->channels[i]->ch_open_count) {
+			count += snprintf(buf + count, PAGE_SIZE - count,
+				"%d %s %s %s %s %s %s\n", bd->channels[i]->ch_portnum,
+				(bd->channels[i]->ch_mostat & UART_MCR_RTS) ? "RTS" : "",
+				(bd->channels[i]->ch_mistat & UART_MSR_CTS) ? "CTS" : "",
+				(bd->channels[i]->ch_mostat & UART_MCR_DTR) ? "DTR" : "",
+				(bd->channels[i]->ch_mistat & UART_MSR_DSR) ? "DSR" : "",
+				(bd->channels[i]->ch_mistat & UART_MSR_DCD) ? "DCD" : "",
+				(bd->channels[i]->ch_mistat & UART_MSR_RI)  ? "RI"  : "");
+		} else {
+			count += snprintf(buf + count, PAGE_SIZE - count,
+				"%d\n", bd->channels[i]->ch_portnum);
+		}
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_msignals, S_IRUSR, dgap_ports_msignals_show, NULL);
+
+
+static ssize_t dgap_ports_iflag_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_iflag);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_iflag, S_IRUSR, dgap_ports_iflag_show, NULL);
+
+
+static ssize_t dgap_ports_cflag_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_cflag);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_cflag, S_IRUSR, dgap_ports_cflag_show, NULL);
+
+
+static ssize_t dgap_ports_oflag_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_oflag);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_oflag, S_IRUSR, dgap_ports_oflag_show, NULL);
+
+
+static ssize_t dgap_ports_lflag_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_lflag);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_lflag, S_IRUSR, dgap_ports_lflag_show, NULL);
+
+
+static ssize_t dgap_ports_digi_flag_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_digi.digi_flags);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_digi_flag, S_IRUSR, dgap_ports_digi_flag_show, NULL);
+
+
+static ssize_t dgap_ports_rxcount_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %ld\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_rxcount);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_rxcount, S_IRUSR, dgap_ports_rxcount_show, NULL);
+
+
+static ssize_t dgap_ports_txcount_show(struct device *p, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	int count = 0;
+	int i = 0;
+
+	DGAP_VERIFY_BOARD(p, bd);
+
+	for (i = 0; i < bd->nasync; i++) {
+		count += snprintf(buf + count, PAGE_SIZE - count, "%d %ld\n",
+			bd->channels[i]->ch_portnum, bd->channels[i]->ch_txcount);
+	}
+	return count;
+}
+static DEVICE_ATTR(ports_txcount, S_IRUSR, dgap_ports_txcount_show, NULL);
+
+
+/* this function creates the sys files that will export each signal status
+ * to sysfs each value will be put in a separate filename
+ */
+static void dgap_create_ports_sysfiles(struct board_t *bd)
+{
+	int rc = 0;
+
+	dev_set_drvdata(&bd->pdev->dev, bd);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_state);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_baud);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_msignals);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_iflag);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_cflag);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_oflag);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_lflag);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_digi_flag);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_rxcount);
+	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_txcount);
+	if (rc) {
+		printk(KERN_ERR "DGAP: sysfs device_create_file failed!\n");
+	}
+}
+
+
+/* removes all the sys files created for that port */
+static void dgap_remove_ports_sysfiles(struct board_t *bd)
+{
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_state);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_baud);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_msignals);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_iflag);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_cflag);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_oflag);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_lflag);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_digi_flag);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_rxcount);
+	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_txcount);
+}
+
+
+static ssize_t dgap_tty_state_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%s", un->un_open_count ? "Open" : "Closed");
+}
+static DEVICE_ATTR(state, S_IRUSR, dgap_tty_state_show, NULL);
+
+
+static ssize_t dgap_tty_baud_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", ch->ch_baud_info);
+}
+static DEVICE_ATTR(baud, S_IRUSR, dgap_tty_baud_show, NULL);
+
+
+static ssize_t dgap_tty_msignals_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	if (ch->ch_open_count) {
+		return snprintf(buf, PAGE_SIZE, "%s %s %s %s %s %s\n",
+			(ch->ch_mostat & UART_MCR_RTS) ? "RTS" : "",
+			(ch->ch_mistat & UART_MSR_CTS) ? "CTS" : "",
+			(ch->ch_mostat & UART_MCR_DTR) ? "DTR" : "",
+			(ch->ch_mistat & UART_MSR_DSR) ? "DSR" : "",
+			(ch->ch_mistat & UART_MSR_DCD) ? "DCD" : "",
+			(ch->ch_mistat & UART_MSR_RI)  ? "RI"  : "");
+	}
+	return 0;
+}
+static DEVICE_ATTR(msignals, S_IRUSR, dgap_tty_msignals_show, NULL);
+
+
+static ssize_t dgap_tty_iflag_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_iflag);
+}
+static DEVICE_ATTR(iflag, S_IRUSR, dgap_tty_iflag_show, NULL);
+
+
+static ssize_t dgap_tty_cflag_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_cflag);
+}
+static DEVICE_ATTR(cflag, S_IRUSR, dgap_tty_cflag_show, NULL);
+
+
+static ssize_t dgap_tty_oflag_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_oflag);
+}
+static DEVICE_ATTR(oflag, S_IRUSR, dgap_tty_oflag_show, NULL);
+
+
+static ssize_t dgap_tty_lflag_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_lflag);
+}
+static DEVICE_ATTR(lflag, S_IRUSR, dgap_tty_lflag_show, NULL);
+
+
+static ssize_t dgap_tty_digi_flag_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_digi.digi_flags);
+}
+static DEVICE_ATTR(digi_flag, S_IRUSR, dgap_tty_digi_flag_show, NULL);
+
+
+static ssize_t dgap_tty_rxcount_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%ld\n", ch->ch_rxcount);
+}
+static DEVICE_ATTR(rxcount, S_IRUSR, dgap_tty_rxcount_show, NULL);
+
+
+static ssize_t dgap_tty_txcount_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+	return snprintf(buf, PAGE_SIZE, "%ld\n", ch->ch_txcount);
+}
+static DEVICE_ATTR(txcount, S_IRUSR, dgap_tty_txcount_show, NULL);
+
+
+static ssize_t dgap_tty_name_show(struct device *d, struct device_attribute *attr, char *buf)
+{
+	struct board_t *bd;
+	struct channel_t *ch;
+	struct un_t *un;
+	int	cn;
+	int	bn;
+	struct cnode *cptr = NULL;
+	int found = FALSE;
+	int ncount = 0;
+	int starto = 0;
+	int i = 0;
+
+	if (!d)
+		return (0);
+	un = dev_get_drvdata(d);
+	if (!un || un->magic != DGAP_UNIT_MAGIC)
+		return (0);
+	ch = un->un_ch;
+	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
+		return (0);
+	bd = ch->ch_bd;
+	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
+		return (0);
+	if (bd->state != BOARD_READY)
+		return (0);
+
+        bn = bd->boardnum;
+	cn = ch->ch_portnum;
+
+	for (cptr = bd->bd_config; cptr; cptr = cptr->next) {
+
+		if ((cptr->type == BNODE) &&
+		    ((cptr->u.board.type == APORT2_920P) || (cptr->u.board.type == APORT4_920P) ||
+		     (cptr->u.board.type == APORT8_920P) || (cptr->u.board.type == PAPORT4) ||
+		     (cptr->u.board.type == PAPORT8))) {
+
+				found = TRUE;
+				if (cptr->u.board.v_start)
+					starto = cptr->u.board.start;
+				else
+					starto = 1;
+		}
+
+		if (cptr->type == TNODE && found == TRUE) {
+			char *ptr1;
+			if (strstr(cptr->u.ttyname, "tty")) {
+				ptr1 = cptr->u.ttyname;
+				ptr1 += 3;
+			}
+			else {
+				ptr1 = cptr->u.ttyname;
+			}
+
+			for (i = 0; i < dgap_config_get_number_of_ports(bd); i++) {
+				if (cn == i) {
+					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
+						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
+						ptr1, i + starto);
+				}
+			}
+		}
+
+		if (cptr->type == CNODE) {
+
+			for (i = 0; i < cptr->u.conc.nport; i++) {
+				if (cn == (i + ncount)) {
+
+					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
+						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
+						cptr->u.conc.id,
+						i + (cptr->u.conc.v_start ? cptr->u.conc.start : 1));
+				}
+			}
+
+			ncount += cptr->u.conc.nport;
+		}
+
+		if (cptr->type == MNODE) {
+
+			for (i = 0; i < cptr->u.module.nport; i++) {
+				if (cn == (i + ncount)) {
+					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
+						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
+						cptr->u.module.id,
+						i + (cptr->u.module.v_start ? cptr->u.module.start : 1));
+				}
+			}
+
+			ncount += cptr->u.module.nport;
+
+		}
+	}
+
+	return snprintf(buf, PAGE_SIZE, "%s_dgap_%d_%d\n",
+		(un->un_type == DGAP_PRINT) ? "pr" : "tty", bn, cn);
+
+}
+static DEVICE_ATTR(custom_name, S_IRUSR, dgap_tty_name_show, NULL);
+
+
+static struct attribute *dgap_sysfs_tty_entries[] = {
+	&dev_attr_state.attr,
+	&dev_attr_baud.attr,
+	&dev_attr_msignals.attr,
+	&dev_attr_iflag.attr,
+	&dev_attr_cflag.attr,
+	&dev_attr_oflag.attr,
+	&dev_attr_lflag.attr,
+	&dev_attr_digi_flag.attr,
+	&dev_attr_rxcount.attr,
+	&dev_attr_txcount.attr,
+	&dev_attr_custom_name.attr,
+	NULL
+};
+
+
+static struct attribute_group dgap_tty_attribute_group = {
+	.name = NULL,
+	.attrs = dgap_sysfs_tty_entries,
+};
+
+
+
+
+static void dgap_create_tty_sysfs(struct un_t *un, struct device *c)
+{
+	int ret;
+
+	ret = sysfs_create_group(&c->kobj, &dgap_tty_attribute_group);
+	if (ret) {
+		printk(KERN_ERR "dgap: failed to create sysfs tty device attributes.\n");
+		sysfs_remove_group(&c->kobj, &dgap_tty_attribute_group);
+		return;
+	}
+
+	dev_set_drvdata(c, un);
+
+}
+
+
+static void dgap_remove_tty_sysfs(struct device *c)
+{
+	sysfs_remove_group(&c->kobj, &dgap_tty_attribute_group);
+}
diff -urpN linux-3.13.1-orig/drivers/staging/dgap/dgap_driver.c linux-3.13.1-new/drivers/staging/dgap/dgap_driver.c
--- linux-3.13.1-orig/drivers/staging/dgap/dgap_driver.c	2014-02-11 10:07:00.122346031 -0500
+++ linux-3.13.1-new/drivers/staging/dgap/dgap_driver.c	1969-12-31 19:00:00.000000000 -0500
@@ -1,8606 +0,0 @@
-/*
- * Copyright 2003 Digi International (www.digi.com)
- *	Scott H Kilau <Scott_Kilau at digi dot com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- * 
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the 
- * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR 
- * PURPOSE.  See the GNU General Public License for more details.
- * 
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- */
-
-/*
- *      In the original out of kernel Digi dgap driver, firmware
- *      loading was done via user land to driver handshaking.
- *
- *      For cards that support a concentrator (port expander),
- *      I believe the concentrator its self told the card which
- *      concentrator is actually attached and then that info
- *      was used to tell user land which concentrator firmware
- *      image was to be downloaded. I think even the BIOS or
- *      FEP images required would change with the connection
- *      of a particular concentrator. 
- *
- *      Since I have no access to any of these cards or
- *      concentrators, I cannot put the correct concentrator
- *      firmware file names into the firmware_info structure
- *      as is now done for the BIOS and FEP images. 
- *
- *      I think, but am not certain, that the cards supporting
- *      concentrators will function without them. So support
- *      of these cards has been left in this driver.
- *
- *      In order to fully support those cards, they would
- *      either have to be acquired for dissection or maybe
- *      Digi International could provide some assistance.
- */
-#undef DIGI_CONCENTRATORS_SUPPORTED
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/delay.h>	/* For udelay */
-#include <linux/slab.h>
-#include <asm/uaccess.h>	/* For copy_from_user/copy_to_user */
-#include <linux/sched.h>
-#include <linux/firmware.h>
-
-#include <linux/version.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>     /* For tty_schedule_flip */
-#include <linux/ctype.h>
-
-#include <linux/interrupt.h>    /* For tasklet and interrupt structs/defines */
-#include <linux/serial_reg.h>
-#include <asm/uaccess.h>        /* For copy_from_user/copy_to_user */
-#include <asm/io.h>             /* For read[bwl]/write[bwl] */
-
-#include <linux/string.h>
-#include <linux/device.h>
-#include <linux/kdev_t.h>
-
-#include "dgap_driver.h"
-
-/*
- * Function prototypes.
- */
-static int dgap_gettok(char **in, struct cnode *p);
-static char *dgap_getword(char **in);
-static char *dgap_savestring(char *s);
-static struct cnode *dgap_newnode(int t);
-static int dgap_checknode(struct cnode *p);
-static void dgap_err(char *s);
-
-/*
- * Our needed internal static variables...
- */
-static struct cnode dgap_head;
-#define MAXCWORD 200
-static char dgap_cword[MAXCWORD];
-
-#define init_MUTEX(sem)         sema_init(sem, 1)
-#define DECLARE_MUTEX(name)     \
-        struct semaphore name = __SEMAPHORE_INITIALIZER(name, 1)
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Digi International, http://www.digi.com";);
-MODULE_DESCRIPTION("Driver for the Digi International EPCA PCI based product line");
-MODULE_SUPPORTED_DEVICE("dgap");
-
-/*
- * insmod command line overrideable parameters
- *
- * NOTE: we use a set of macros to create the variables, which allows
- * us to specify the variable type, name, initial value, and description.
- */
-PARM_INT(debug,		0x00,		0644,	"Driver debugging level");
-PARM_INT(rawreadok,	1,		0644,	"Bypass flip buffers on input");
-
-/**************************************************************************
- *
- * protos for this file
- *
- */
-
-static int		dgap_start(void);
-static void		dgap_init_globals(void);
-static int		dgap_found_board(struct pci_dev *pdev, int id);
-static void		dgap_cleanup_board(struct board_t *brd);
-static void		dgap_poll_handler(ulong dummy);
-static int		dgap_init_pci(void);
-static int		dgap_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
-static void		dgap_remove_one(struct pci_dev *dev);
-static int		dgap_probe1(struct pci_dev *pdev, int card_type);
-static void		dgap_mbuf(struct board_t *brd, const char *fmt, ...);
-static int		dgap_do_remap(struct board_t *brd);
-static irqreturn_t	dgap_intr(int irq, void *voidbrd);
-static void 		dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds);
-static int 		dgap_event(struct board_t *bd);
-static int 		dgap_firmware_load(struct pci_dev *pdev, int card_type);
-static void 		dgap_do_bios_load(struct board_t *brd, uchar *ubios, int len);
-static void 		dgap_do_fep_load(struct board_t *brd, uchar *ufep, int len);
-static void 		dgap_sysfs_create(struct board_t *brd);
-static void 		dgap_get_vpd(struct board_t *brd);
-static void 		dgap_do_reset_board(struct board_t *brd);
-static void 		dgap_do_wait_for_bios(struct board_t *brd);
-static void 		dgap_do_wait_for_fep(struct board_t *brd);
-static int 		dgap_after_config_loaded(int brd);
-static int 		dgap_finalize_board_init(struct board_t *brd);
-static void 		dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds);
-static int 		dgap_event(struct board_t *bd);
-
-/*****************************************************************************
- * Function prototypes from dgap_tty.c
- *****************************************************************************/
-static int dgap_tty_open(struct tty_struct *tty, struct file *file);
-static void dgap_tty_close(struct tty_struct *tty, struct file *file);
-static int dgap_block_til_ready(struct tty_struct *tty, struct file *file, struct channel_t *ch);
-static int dgap_tty_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
-static int dgap_tty_digigeta(struct tty_struct *tty, struct digi_t __user *retinfo);
-static int dgap_tty_digiseta(struct tty_struct *tty, struct digi_t __user *new_info);
-static int dgap_tty_digigetedelay(struct tty_struct *tty, int __user *retinfo);
-static int dgap_tty_digisetedelay(struct tty_struct *tty, int __user *new_info);
-static int dgap_tty_write_room(struct tty_struct* tty);
-static int dgap_tty_chars_in_buffer(struct tty_struct* tty);
-static void dgap_tty_start(struct tty_struct *tty);
-static void dgap_tty_stop(struct tty_struct *tty);
-static void dgap_tty_throttle(struct tty_struct *tty);
-static void dgap_tty_unthrottle(struct tty_struct *tty);
-static void dgap_tty_flush_chars(struct tty_struct *tty);
-static void dgap_tty_flush_buffer(struct tty_struct *tty);
-static void dgap_tty_hangup(struct tty_struct *tty);
-static int dgap_wait_for_drain(struct tty_struct *tty);
-static int dgap_set_modem_info(struct tty_struct *tty, unsigned int command, unsigned int __user *value);
-static int dgap_get_modem_info(struct channel_t *ch, unsigned int __user *value);
-static int dgap_tty_digisetcustombaud(struct tty_struct *tty, int __user *new_info);
-static int dgap_tty_digigetcustombaud(struct tty_struct *tty, int __user *retinfo);
-static int dgap_tty_tiocmget(struct tty_struct *tty);
-static int dgap_tty_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear);
-static int dgap_tty_send_break(struct tty_struct *tty, int msec);
-static void dgap_tty_wait_until_sent(struct tty_struct *tty, int timeout);
-static int dgap_tty_write(struct tty_struct *tty, const unsigned char *buf, int count);
-static void dgap_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios);
-static int dgap_tty_put_char(struct tty_struct *tty, unsigned char c);
-static void dgap_tty_send_xchar(struct tty_struct *tty, char ch);
-
-static const struct tty_operations dgap_tty_ops = {
-	.open = dgap_tty_open,
-	.close = dgap_tty_close,
-	.write = dgap_tty_write,
-	.write_room = dgap_tty_write_room,
-	.flush_buffer = dgap_tty_flush_buffer,
-	.chars_in_buffer = dgap_tty_chars_in_buffer,
-	.flush_chars = dgap_tty_flush_chars,
-	.ioctl = dgap_tty_ioctl,
-	.set_termios = dgap_tty_set_termios,
-	.stop = dgap_tty_stop, 
-	.start = dgap_tty_start,
-	.throttle = dgap_tty_throttle,
-	.unthrottle = dgap_tty_unthrottle,
-	.hangup = dgap_tty_hangup,
-	.put_char = dgap_tty_put_char,
-	.tiocmget = dgap_tty_tiocmget,
-	.tiocmset = dgap_tty_tiocmset,
-	.break_ctl = dgap_tty_send_break,
-	.wait_until_sent = dgap_tty_wait_until_sent,
-	.send_xchar = dgap_tty_send_xchar
-};
-
-/*****************************************************************************
- * Function prototypes from dgap_sysfs.h
- *****************************************************************************/
-static void dgap_create_ports_sysfiles(struct board_t *bd);
-static void dgap_remove_ports_sysfiles(struct board_t *bd);
-static void dgap_create_driver_sysfiles(struct pci_driver *);
-static void dgap_remove_driver_sysfiles(struct pci_driver *);
-static void dgap_create_tty_sysfs(struct un_t *un, struct device *c);
-static void dgap_remove_tty_sysfs(struct device *c);
-
-#ifdef DIGI_CONCENTRATORS_SUPPORTED
-static void             dgap_do_conc_load(struct board_t *brd, uchar *uaddr, int len);
-#endif
-
-/* Driver load/unload functions */
-int			dgap_init_module(void);
-void			dgap_cleanup_module(void);
-
-module_init(dgap_init_module);
-module_exit(dgap_cleanup_module);
-
-/*
- * File operations permitted on Control/Management major.
- */
-static struct file_operations DgapBoardFops =
-{
-	.owner		=	THIS_MODULE,
-};
-
-/*
- * Globals
- */
-uint			dgap_NumBoards;
-struct board_t		*dgap_Board[MAXBOARDS];
-DEFINE_SPINLOCK(dgap_global_lock);
-ulong			dgap_poll_counter;
-char			*dgap_config_buf;
-int			dgap_driver_state = DRIVER_INITIALIZED;
-DEFINE_SPINLOCK(dgap_dl_lock);
-wait_queue_head_t	dgap_dl_wait;
-int			dgap_dl_action;
-int			dgap_poll_tick = 20;	/* Poll interval - 20 ms */
-
-/*
- * Static vars.
- */
-static int		dgap_Major_Control_Registered = FALSE;
-static uint		dgap_driver_start = FALSE;
-static uint 		dgap_count = 500;
-static struct class *	dgap_class;
-
-/*
- * Poller stuff
- */
-static 			DEFINE_SPINLOCK(dgap_poll_lock);	/* Poll scheduling lock */
-static ulong		dgap_poll_time;				/* Time of next poll */
-static uint		dgap_poll_stop;				/* Used to tell poller to stop */
-static struct timer_list dgap_poll_timer;
-
-/*
-     SUPPORTED PRODUCTS
-
-     Card Model               Number of Ports      Interface
-     ----------------------------------------------------------------
-     Acceleport Xem           4 - 64              (EIA232 & EIA422)
-     Acceleport Xr            4 & 8               (EIA232)
-     Acceleport Xr 920        4 & 8               (EIA232)
-     Acceleport C/X           8 - 128             (EIA232)
-     Acceleport EPC/X         8 - 224             (EIA232)
-     Acceleport Xr/422        4 & 8               (EIA422)
-     Acceleport 2r/920        2                   (EIA232)
-     Acceleport 4r/920        4                   (EIA232)
-     Acceleport 8r/920        8                   (EIA232)
-
-     IBM 8-Port Asynchronous PCI Adapter          (EIA232)
-     IBM 128-Port Asynchronous PCI Adapter        (EIA232 & EIA422)
-*/
-
-static struct pci_device_id dgap_pci_tbl[] = {
-	{       DIGI_VID, PCI_DEVICE_XEM_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	0 },
-	{       DIGI_VID, PCI_DEVICE_CX_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,   1 },
-	{       DIGI_VID, PCI_DEVICE_CX_IBM_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	2 },
-	{       DIGI_VID, PCI_DEVICE_EPCJ_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	3 },
-	{       DIGI_VID, PCI_DEVICE_920_2_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	4 },
-	{       DIGI_VID, PCI_DEVICE_920_4_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	5 },
-	{       DIGI_VID, PCI_DEVICE_920_8_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	6 },
-	{       DIGI_VID, PCI_DEVICE_XR_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	7 },
-	{       DIGI_VID, PCI_DEVICE_XRJ_DID,	PCI_ANY_ID, PCI_ANY_ID, 0, 0,	8 },
-	{       DIGI_VID, PCI_DEVICE_XR_422_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	9 },
-	{       DIGI_VID, PCI_DEVICE_XR_IBM_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	10 },
-	{       DIGI_VID, PCI_DEVICE_XR_SAIP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	11 },
-	{       DIGI_VID, PCI_DEVICE_XR_BULL_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	12 },
-	{       DIGI_VID, PCI_DEVICE_920_8_HP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13 },
-	{       DIGI_VID, PCI_DEVICE_XEM_HP_DID, PCI_ANY_ID, PCI_ANY_ID, 0, 0,	14 },
-	{0,}					/* 0 terminated list. */
-};
-MODULE_DEVICE_TABLE(pci, dgap_pci_tbl);
-
-/*
- * A generic list of Product names, PCI Vendor ID, and PCI Device ID.
- */
-struct board_id {
-	uint config_type;
-	uchar *name;
-	uint maxports;
-	uint dpatype;
-};
-
-static struct board_id dgap_Ids[] =
-{
-	{	PPCM,		PCI_DEVICE_XEM_NAME,	64,	(T_PCXM | T_PCLITE | T_PCIBUS)	},
-	{	PCX,		PCI_DEVICE_CX_NAME,	128,	(T_CX | T_PCIBUS)		},
-	{	PCX,		PCI_DEVICE_CX_IBM_NAME,	128,	(T_CX | T_PCIBUS)		},
-	{	PEPC,		PCI_DEVICE_EPCJ_NAME,	224,	(T_EPC  | T_PCIBUS)		},
-	{	APORT2_920P,	PCI_DEVICE_920_2_NAME,	2,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	APORT4_920P,	PCI_DEVICE_920_4_NAME,	4,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	APORT8_920P,	PCI_DEVICE_920_8_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XR_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XRJ_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XR_422_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XR_IBM_NAME,	8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XR_SAIP_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PAPORT8,	PCI_DEVICE_XR_BULL_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	APORT8_920P,	PCI_DEVICE_920_8_HP_NAME, 8,	(T_PCXR | T_PCLITE | T_PCIBUS)	},
-	{	PPCM,		PCI_DEVICE_XEM_HP_NAME,	64,	(T_PCXM | T_PCLITE | T_PCIBUS)	},
-	{0,}						/* 0 terminated list. */
-};
-
-static struct pci_driver dgap_driver = {
-	.name		= "dgap",
-	.probe		= dgap_init_one,
-	.id_table	= dgap_pci_tbl,
-	.remove		= dgap_remove_one,
-};
-
-struct firmware_info {
-        uchar *conf_name;       /* dgap.conf */	
-	uchar *bios_name;	/* BIOS filename */
-        uchar *fep_name;	/* FEP  filename */
-	uchar *con_name;	/* Concentrator filename  FIXME*/ 
-	int num;                /* sequence number */
-};
-
-/*
- * Firmware - BIOS, FEP, and CONC filenames
- */
-#define _CONFIG_ "dgap/dgap.conf"
-static struct firmware_info fw_info[] = {
-	{ _CONFIG_, "dgap/sxbios.bin",  "dgap/sxfep.bin",  0, 0 },	/* XEM_DID */
-	{ _CONFIG_, "dgap/cxpbios.bin", "dgap/cxpfep.bin", 0, 1 },	/* CX_DID  */           
-	{ _CONFIG_, "dgap/cxpbios.bin", "dgap/cxpfep.bin", 0, 2 },	/* CX_IBM_DID */         
-	{ _CONFIG_, "dgap/pcibios.bin", "dgap/pcifep.bin", 0, 3 },	/* EPCJ_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 4 }, 	/* 920_2_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 5 },	/* 920_4_DID */	
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 6 },	/* 920_8_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 7 },	/* XR_DID */ 
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 8 },	/* XRJ_DID */ 
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 9 },	/* XR_422_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 10 },	/* XR_IBM_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 11 },	/* XR_SAIP_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 12 },	/* XR_BULL_DID */
-	{ _CONFIG_, "dgap/xrbios.bin",  "dgap/xrfep.bin",  0, 13 },	/* 920_8_HP_DID */
-	{ _CONFIG_, "dgap/sxbios.bin",  "dgap/sxfep.bin",  0, 14 },	/* XEM_HP_DID */
-	{0,}
-};
-
-struct toklist {
-	int	token;
-	char	*string;
-};
-
-static struct toklist dgap_tlist[] = {
-	{	BEGIN,		"config_begin"			},
-	{	END,		"config_end"			},
-	{	BOARD,		"board"				},
-	{	PCX,		"Digi_AccelePort_C/X_PCI"	},	/* C/X_PCI */
-	{	PEPC,		"Digi_AccelePort_EPC/X_PCI"	},	/* EPC/X_PCI */
-	{	PPCM,		"Digi_AccelePort_Xem_PCI"	},	/* PCI/Xem */
-	{	APORT2_920P,	"Digi_AccelePort_2r_920_PCI"	},
-	{	APORT4_920P,	"Digi_AccelePort_4r_920_PCI"	},
-	{	APORT8_920P,	"Digi_AccelePort_8r_920_PCI"	},
-	{	PAPORT4,	"Digi_AccelePort_4r_PCI(EIA-232/RS-422)" },
-	{	PAPORT8,	"Digi_AccelePort_8r_PCI(EIA-232/RS-422)" },
-	{	IO,		"io"				},
-	{	PCIINFO,	"pciinfo"			},
-	{	LINE,		"line"				},
-	{	CONC,		"conc"				},
-	{	CONC,		"concentrator"			},
-	{	CX,		"cx"				},
-	{	CX,		"ccon"				},
-	{	EPC,		"epccon"			},
-	{	EPC,		"epc"				},
-	{	MOD,		"module"			},
-	{	ID,		"id"				},
-	{	STARTO,		"start"				},
-	{	SPEED,		"speed"				},
-	{	CABLE,		"cable"				},
-	{	CONNECT,	"connect"			},
-	{	METHOD,		"method"			},
-	{	STATUS,		"status"			},
-	{	CUSTOM,		"Custom"			},
-	{	BASIC,		"Basic"				},
-	{	MEM,		"mem"				},
-	{	MEM,		"memory"			},
-	{	PORTS,		"ports"				},
-	{	MODEM,		"modem"				},
-	{	NPORTS,		"nports"			},
-	{	TTYN,		"ttyname"			},
-	{	CU,		"cuname"			},
-	{	PRINT,		"prname"			},
-	{	CMAJOR,		"major"				},
-	{	ALTPIN,		"altpin"			},
-	{	USEINTR,	"useintr"			},
-	{	TTSIZ,		"ttysize"			},
-	{	CHSIZ,		"chsize"			},
-	{	BSSIZ,		"boardsize"			},
-	{	UNTSIZ,		"schedsize"			},
-	{	F2SIZ,		"f2200size"			},
-	{	VPSIZ,		"vpixsize"			},
-	{	0,		NULL				}
-};
-
-char *dgap_state_text[] = {
-	"Board Failed",
-	"Configuration for board not found.\n\t\t\tRun mpi to configure board.",
-	"Board Found",
-	"Need Reset",
-	"Finished Reset",
-	"Need Config",
-	"Finished Config",
-	"Need Device Creation",
-	"Requested Device Creation",
-	"Finished Device Creation",
-	"Need BIOS Load", 
-	"Requested BIOS", 
-	"Doing BIOS Load",
-	"Finished BIOS Load",
-	"Need FEP Load", 
-	"Requested FEP",
-	"Doing FEP Load",
-	"Finished FEP Load",
-	"Requested PROC creation",
-	"Finished PROC creation",
-	"Board READY",
-};
-
-char *dgap_driver_state_text[] = {
-	"Driver Initialized",
-	"Driver needs configuration load.",
-	"Driver requested configuration from download daemon.",
-	"Driver Ready."
-};
-
-/*
- * internal variables
- */
-static struct board_t	*dgap_BoardsByMajor[256];
-static uchar		*dgap_TmpWriteBuf = NULL;
-static DECLARE_MUTEX(dgap_TmpWriteSem);
-
-/*
- * Default transparent print information.
- */
-static struct digi_t dgap_digi_init = {
-	.digi_flags =	DIGI_COOK,	/* Flags			*/
-	.digi_maxcps =	100,		/* Max CPS			*/
-	.digi_maxchar =	50,		/* Max chars in print queue	*/
-	.digi_bufsize =	100,		/* Printer buffer size		*/
-	.digi_onlen =	4,		/* size of printer on string	*/
-	.digi_offlen =	4,		/* size of printer off string	*/
-	.digi_onstr =	"\033[5i",	/* ANSI printer on string ]	*/
-	.digi_offstr =	"\033[4i",	/* ANSI printer off string ]	*/
-	.digi_term =	"ansi"		/* default terminal type	*/
-};
-
-
-/*
- * Define a local default termios struct. All ports will be created
- * with this termios initially.
- *
- * This defines a raw port at 9600 baud, 8 data bits, no parity,
- * 1 stop bit.
- */
-
-static struct ktermios DgapDefaultTermios =
-{
-	.c_iflag =	(DEFAULT_IFLAGS),	/* iflags */
-	.c_oflag =	(DEFAULT_OFLAGS),	/* oflags */
-	.c_cflag =	(DEFAULT_CFLAGS),	/* cflags */
-	.c_lflag =	(DEFAULT_LFLAGS),	/* lflags */
-	.c_cc =		INIT_C_CC,
-	.c_line = 	0,
-};
-
-
-/************************************************************************
- *
- * Driver load/unload functions
- *
- ************************************************************************/
-
-/*
- * init_module()
- *
- * Module load.  This is where it all starts.
- */
-int dgap_init_module(void)
-{
-	int rc = 0;
-
-	APR(("%s, Digi International Part Number %s\n", DG_NAME, DG_PART));
-
-	dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
-	
-	/*
-	 * Initialize global stuff
-	 */
-	rc = dgap_start();
-
-	if (rc < 0) 
-		return(rc);
-
-	/*
-	 * Find and configure all the cards
-	 */
-	rc = dgap_init_pci();
-
-	/*
-	 * If something went wrong in the scan, bail out of driver.
-	 */
-	if (rc < 0) {
-		/* Only unregister the pci driver if it was actually registered. */
-		if (dgap_NumBoards)
-			pci_unregister_driver(&dgap_driver);
-		else
-			printk("WARNING: dgap driver load failed.  No DGAP boards found.\n");
-
-		dgap_cleanup_module();
-	} else {
-		dgap_create_driver_sysfiles(&dgap_driver);
-		dgap_driver_state = DRIVER_READY;
-	}
-  
-	DPR_INIT(("Finished init_module. Returning %d\n", rc));
-	return (rc);
-}
-
-/*
- * Start of driver.
- */
-static int dgap_start(void)
-{
-	int rc = 0;
-	unsigned long flags;
-
-	if (dgap_driver_start == FALSE) {
-
-		dgap_driver_start = TRUE;
-
-	        /* make sure that the globals are init'd before we do anything else */
-	        dgap_init_globals();
-
-		dgap_NumBoards = 0;
-
-		APR(("For the tools package or updated drivers please visit http://www.digi.com\n";));
-
-		/*
-		 * Register our base character device into the kernel.
-		 * This allows the download daemon to connect to the downld device
-		 * before any of the boards are init'ed.
-		 */
-		if (!dgap_Major_Control_Registered) {
-			/*
-			 * Register management/dpa devices
-			 */
-			rc = register_chrdev(DIGI_DGAP_MAJOR, "dgap", &DgapBoardFops);
-			if (rc < 0) {
-				APR(("Can't register dgap driver device (%d)\n", rc));
-				return (rc);
-			}
-
-			dgap_class = class_create(THIS_MODULE, "dgap_mgmt");
-			device_create(dgap_class, NULL,
-				MKDEV(DIGI_DGAP_MAJOR, 0),
-				NULL, "dgap_mgmt");
-			dgap_Major_Control_Registered = TRUE;
-		}
-
-		/*
-		 * Init any global tty stuff.
-		 */
-		rc = dgap_tty_preinit();
-
-		if (rc < 0) {
-			APR(("tty preinit - not enough memory (%d)\n", rc));
-			return(rc); 
-		}
-
-		/* Start the poller */
-		DGAP_LOCK(dgap_poll_lock, flags);
-		init_timer(&dgap_poll_timer);
-		dgap_poll_timer.function = dgap_poll_handler;
-		dgap_poll_timer.data = 0;
-		dgap_poll_time = jiffies + dgap_jiffies_from_ms(dgap_poll_tick);
-		dgap_poll_timer.expires = dgap_poll_time;
-		DGAP_UNLOCK(dgap_poll_lock, flags);
-
-		add_timer(&dgap_poll_timer);
-
-		dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
-	}
-
-	return (rc);
-}
-
-/*
- * Register pci driver, and return how many boards we have.
- */
-static int dgap_init_pci(void)
-{
-	return pci_register_driver(&dgap_driver);
-}
-
-/* returns count (>= 0), or negative on error */
-static int dgap_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
-{
-	int rc;
-
-	/* wake up and enable device */
-	rc = pci_enable_device(pdev);
-
-	if (rc < 0) {
-		rc = -EIO;
-	} else {  
-		rc = dgap_probe1(pdev, ent->driver_data);
-		if (rc == 0) {
-			dgap_NumBoards++;
-			DPR_INIT(("Incrementing numboards to %d\n", dgap_NumBoards));
-			rc = dgap_firmware_load(pdev, ent->driver_data);
-		}
-	}
-	return rc;
-}               
-
-static int dgap_probe1(struct pci_dev *pdev, int card_type)
-{
-	return dgap_found_board(pdev, card_type);
-}
-         
-static void dgap_remove_one(struct pci_dev *dev)
-{
-	/* Do Nothing */
-}
-
-/*
- * dgap_cleanup_module()
- *
- * Module unload.  This is where it all ends.
- */
-void dgap_cleanup_module(void)
-{
-	int i;
-	ulong lock_flags;
-
-	DGAP_LOCK(dgap_poll_lock, lock_flags);
-	dgap_poll_stop = 1;
-	DGAP_UNLOCK(dgap_poll_lock, lock_flags);
-
-	/* Turn off poller right away. */
-	del_timer_sync(&dgap_poll_timer);
-
-	dgap_remove_driver_sysfiles(&dgap_driver);
-
-
-	if (dgap_Major_Control_Registered) {
-		device_destroy(dgap_class, MKDEV(DIGI_DGAP_MAJOR, 0));
-		device_destroy(dgap_class, MKDEV(DIGI_DGAP_MAJOR, 1));
-		class_destroy(dgap_class);
-		unregister_chrdev(DIGI_DGAP_MAJOR, "dgap");
-	}
-
-	kfree(dgap_config_buf);
-
-	for (i = 0; i < dgap_NumBoards; ++i) {
-		dgap_remove_ports_sysfiles(dgap_Board[i]);
-		dgap_tty_uninit(dgap_Board[i]);
-		dgap_cleanup_board(dgap_Board[i]);
-	}
-
-	dgap_tty_post_uninit();
-
-#if defined(DGAP_TRACER)
-	/* last thing, make sure we release the tracebuffer */
-	dgap_tracer_free();
-#endif
-	if (dgap_NumBoards)
-		pci_unregister_driver(&dgap_driver);
-}
-
-/*
- * dgap_cleanup_board()
- *
- * Free all the memory associated with a board
- */
-static void dgap_cleanup_board(struct board_t *brd)
-{
-	int i = 0;
-
-        if(!brd || brd->magic != DGAP_BOARD_MAGIC)
-                return;
-
-	if (brd->intr_used && brd->irq)
-		free_irq(brd->irq, brd);
-
-	tasklet_kill(&brd->helper_tasklet);
-
-	if (brd->re_map_port) {
-		release_mem_region(brd->membase + 0x200000, 0x200000);
-		iounmap(brd->re_map_port);
-		brd->re_map_port = NULL;
-	}
-
-	if (brd->re_map_membase) {
-		release_mem_region(brd->membase, 0x200000);
-		iounmap(brd->re_map_membase);
-		brd->re_map_membase = NULL;
-	}
-
-        if (brd->msgbuf_head) {
-                unsigned long flags;
-
-                DGAP_LOCK(dgap_global_lock, flags);
-                brd->msgbuf = NULL;
-                printk("%s", brd->msgbuf_head);
-                kfree(brd->msgbuf_head);
-                brd->msgbuf_head = NULL;
-                DGAP_UNLOCK(dgap_global_lock, flags);
-        }
-
-	/* Free all allocated channels structs */
-	for (i = 0; i < MAXPORTS ; i++) {
-		if (brd->channels[i]) {
-			kfree(brd->channels[i]);
-			brd->channels[i] = NULL;
-		}
-	}
-
-	kfree(brd->flipbuf);
-	kfree(brd->flipflagbuf);
-
-	dgap_Board[brd->boardnum] = NULL;
-
-        kfree(brd);
-}
-
-/*
- * dgap_found_board()
- *
- * A board has been found, init it.
- */
-static int dgap_found_board(struct pci_dev *pdev, int id)
-{
-	struct board_t *brd;
-	unsigned int pci_irq;
-	int i = 0;
-	unsigned long flags;
-
-	/* get the board structure and prep it */
-	brd = dgap_Board[dgap_NumBoards] =
-	(struct board_t *) dgap_driver_kzmalloc(sizeof(struct board_t), GFP_KERNEL);
-	if (!brd) {
-		APR(("memory allocation for board structure failed\n"));
-		return(-ENOMEM);
-	}
-
-	/* make a temporary message buffer for the boot messages */
-	brd->msgbuf = brd->msgbuf_head =
-		(char *) dgap_driver_kzmalloc(sizeof(char) * 8192, GFP_KERNEL);
-	if(!brd->msgbuf) {
-		kfree(brd);
-		APR(("memory allocation for board msgbuf failed\n"));
-		return(-ENOMEM);
-	}
-
-	/* store the info for the board we've found */
-	brd->magic = DGAP_BOARD_MAGIC;
-	brd->boardnum = dgap_NumBoards;
-	brd->firstminor = 0;
-	brd->vendor = dgap_pci_tbl[id].vendor;
-	brd->device = dgap_pci_tbl[id].device;
-	brd->pdev = pdev;
-	brd->pci_bus = pdev->bus->number;
-	brd->pci_slot = PCI_SLOT(pdev->devfn);
-	brd->name = dgap_Ids[id].name;
-	brd->maxports = dgap_Ids[id].maxports;
-	brd->type = dgap_Ids[id].config_type;
-	brd->dpatype = dgap_Ids[id].dpatype;
-	brd->dpastatus = BD_NOFEP;
-	init_waitqueue_head(&brd->state_wait);
-
-	DGAP_SPINLOCK_INIT(brd->bd_lock);
-
-	brd->state		= BOARD_FOUND;
-	brd->runwait		= 0;
-	brd->inhibit_poller	= FALSE;
-	brd->wait_for_bios	= 0;
-	brd->wait_for_fep	= 0;
-
-	for (i = 0; i < MAXPORTS; i++) 
-		brd->channels[i] = NULL;
-
-	/* store which card & revision we have */
-	pci_read_config_word(pdev, PCI_SUBSYSTEM_VENDOR_ID, &brd->subvendor);
-	pci_read_config_word(pdev, PCI_SUBSYSTEM_ID, &brd->subdevice);
-	pci_read_config_byte(pdev, PCI_REVISION_ID, &brd->rev);
-
-	pci_irq = pdev->irq;
-	brd->irq = pci_irq;
-
-	/* get the PCI Base Address Registers */
-
-	if (brd->device == PCI_DEVICE_XRJ_DID || brd->device == PCI_DEVICE_EPCJ_DID) {
-		/* Xr Jupiter and EPC use BAR 2 */
-		brd->membase     = pci_resource_start(pdev, 2);
-		brd->membase_end = pci_resource_end(pdev, 2);
-	} else {		
-		/* Everyone else uses BAR 0 */
-		brd->membase     = pci_resource_start(pdev, 0);
-		brd->membase_end = pci_resource_end(pdev, 0);
-	}
-
-	if (!brd->membase) {
-		APR(("card has no PCI IO resources, failing board.\n"));
-		return -ENODEV;
-	}
-
-	if (brd->membase & 1)
-		brd->membase &= ~3;
-	else
-		brd->membase &= ~15;
-
-	/*
-	 * On the PCI boards, there is no IO space allocated
-	 * The I/O registers will be in the first 3 bytes of the
-	 * upper 2MB of the 4MB memory space.  The board memory
-	 * will be mapped into the low 2MB of the 4MB memory space
-	 */
-	brd->port = brd->membase + PCI_IO_OFFSET;
-	brd->port_end = brd->port + PCI_IO_SIZE;
-
-	/*
-	 * Special initialization for non-PLX boards
-	 */
-	if (brd->device != PCI_DEVICE_XRJ_DID && brd->device != PCI_DEVICE_EPCJ_DID) {
-		unsigned short cmd;
-
-		pci_write_config_byte(pdev, 0x40, 0);
-		pci_write_config_byte(pdev, 0x46, 0);
-
-		/* Limit burst length to 2 doubleword transactions */ 
-		pci_write_config_byte(pdev, 0x42, 1);
-
-		/*
-		 * Enable IO and mem if not already done.
-		 * This was needed for support on Itanium.
-		 */
-		pci_read_config_word(pdev, PCI_COMMAND, &cmd);
-		cmd |= (PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
-		pci_write_config_word(pdev, PCI_COMMAND, cmd);
-	}
-
-	/* init our poll helper tasklet */
-	tasklet_init(&brd->helper_tasklet, dgap_poll_tasklet, (unsigned long) brd);
-
-	 /* Log the information about the board */
-	dgap_mbuf(brd, DRVSTR": board %d: %s (rev %d), irq %d\n",
-		dgap_NumBoards, brd->name, brd->rev, brd->irq);
-
-	DPR_INIT(("dgap_scan(%d) - printing out the msgbuf\n", i));
-	DGAP_LOCK(dgap_global_lock, flags);
-	brd->msgbuf = NULL;
-	printk("%s", brd->msgbuf_head);
-	kfree(brd->msgbuf_head);
-	brd->msgbuf_head = NULL;
-	DGAP_UNLOCK(dgap_global_lock, flags);
-
-	i = dgap_do_remap(brd);
-	if (i)
-		brd->state = BOARD_FAILED;
-	else
-		brd->state = NEED_RESET;
-
-        return 0;
-}
-
-int dgap_finalize_board_init(struct board_t *brd) {
-
-        int rc;
-
-        DPR_INIT(("dgap_finalize_board_init() - start\n"));
-
-	if (!brd || brd->magic != DGAP_BOARD_MAGIC)
-                return(-ENODEV);
-
-        DPR_INIT(("dgap_finalize_board_init() - start #2\n"));
-
-	brd->use_interrupts = dgap_config_get_useintr(brd);
-
-	/*
-	 * Set up our interrupt handler if we are set to do interrupts.
-	 */
-	if (brd->use_interrupts && brd->irq) {
-
-		rc = request_irq(brd->irq, dgap_intr, IRQF_SHARED, "DGAP", brd);
-
-		if (rc) {
-			dgap_mbuf(brd, DRVSTR": Failed to hook IRQ %d. Board will work in poll mode.\n",
-                                  brd->irq);
-			brd->intr_used = 0;
-		} else
-			brd->intr_used = 1;
-	} else 
-		brd->intr_used = 0;
-
-	return(0);
-}
-
-static int dgap_firmware_load(struct pci_dev *pdev, int card_type)
-{
-	struct board_t *brd = dgap_Board[dgap_NumBoards - 1];
-	const struct firmware *fw;
-	char *uaddr;
-	int ret;
-	
-	dgap_get_vpd(brd);
-	dgap_do_reset_board(brd);
-
-	if ((fw_info[card_type].conf_name) && 
-	    (dgap_driver_state == DRIVER_NEED_CONFIG_LOAD)) {
-		ret = request_firmware(&fw, fw_info[card_type].conf_name, &pdev->dev);
-		if (ret) {
-			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
-					"you've placed '%s' file into your firmware "
-					"loader directory (e.g. /lib/firmware)\n",
-					fw_info[card_type].conf_name);
-			return ret; 
-		} else {
-			if (!dgap_config_buf) {
-				uaddr = dgap_config_buf = dgap_driver_kzmalloc(fw->size + 1, GFP_ATOMIC);
-				if (!dgap_config_buf) {
-					DPR_INIT(("DGAP: dgap_firmware_load - unable to allocate memory for config file\n"));
-					release_firmware(fw);
-					return -ENOMEM;
-				}
-			}
-
-			memcpy(uaddr, fw->data, fw->size);
-			release_firmware(fw);
-			uaddr[fw->size + 1] = '\0'; 	// The config file is treated as a string
-
-			if (dgap_parsefile(&uaddr, TRUE) != 0) 
-				return -EINVAL;
-
-			dgap_driver_state = -1;
-		}
-	}
-
-	ret = dgap_after_config_loaded(brd->boardnum);
-	if (ret != 0)
-		return ret;
-	/*
-	 * Match this board to a config the user created for us.
-	 */
-	brd->bd_config = dgap_find_config(brd->type, brd->pci_bus, brd->pci_slot);
-
-	/*
-	 * Because the 4 port Xr products share the same PCI ID
-	 * as the 8 port Xr products, if we receive a NULL config
-	 * back, and this is a PAPORT8 board, retry with a
-	 * PAPORT4 attempt as well.
-	 */
-	if (brd->type == PAPORT8 && !brd->bd_config)
-		brd->bd_config = dgap_find_config(PAPORT4, brd->pci_bus, brd->pci_slot);
-
-	if (!brd->bd_config) {
-		printk(KERN_ERR "DGAP: dgap_firmware_load: No valid configuration found\n");
-		return -EINVAL;
-	}
-
-	dgap_tty_register(brd);
-	dgap_finalize_board_init(brd);
-
-	if (fw_info[card_type].bios_name) {
-		ret = request_firmware(&fw, fw_info[card_type].bios_name, &pdev->dev);
-		if (ret) {
-			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
-					"you've placed '%s' file into your firmware "
-					"loader directory (e.g. /lib/firmware)\n",
-					fw_info[card_type].bios_name);
-			return ret;
-		} else {
-			uaddr = (char *)fw->data;
-			dgap_do_bios_load(brd, uaddr, fw->size);
-			release_firmware(fw);
-
-			/* Wait for BIOS to test board... */
-			dgap_do_wait_for_bios(brd);
-
-			if (brd->state != FINISHED_BIOS_LOAD)
-				return -ENXIO;
-		}
-	}
-
-        if (fw_info[card_type].fep_name) {
-                ret = request_firmware(&fw, fw_info[card_type].fep_name, &pdev->dev);
-                if (ret) {
-                        printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
-                                        "you've placed '%s' file into your firmware "
-                                        "loader directory (e.g. /lib/firmware)\n",
-                                        fw_info[card_type].fep_name);
-                        return ret;
-                } else {
-                        uaddr = (char *)fw->data;
-                        dgap_do_fep_load(brd, uaddr, fw->size);
-			release_firmware(fw);
-
-                        /* Wait for FEP to load on board... */
-                        dgap_do_wait_for_fep(brd);
-
-                        if (brd->state != FINISHED_FEP_LOAD)
-                                return -ENXIO;
-                }
-        }
-
-#ifdef DIGI_CONCENTRATORS_SUPPORTED
-	/*
-	 * If this is a CX or EPCX, we need to see if the firmware
-	 * is requesting a concentrator image from us.
-	 */
-	if ((bd->type == PCX) || (bd->type == PEPC)) {
-		chk_addr = (u16 *) (vaddr + DOWNREQ);
-		/* Nonzero if FEP is requesting concentrator image. */
-		check = readw(chk_addr);
-		vaddr = brd->re_map_membase;
-	}
-
-	if (fw_info[card_type].con_name && check && vaddr) {
-		ret = request_firmware(&fw, fw_info[card_type].con_name, &pdev->dev);
-		if (ret) {
-			printk(KERN_ERR "DGAP: request_firmware failed. Make sure "
-					"you've placed '%s' file into your firmware "
-					"loader directory (e.g. /lib/firmware)\n",
-					fw_info[card_type].con_name);
-			return ret;
-		} else {
-			/* Put concentrator firmware loading code here */
-			offset = readw((u16 *) (vaddr + DOWNREQ)); 
-        		memcpy_toio(offset, fw->data, fw->size);
-
-                        uaddr = (char *)fw->data;
-			dgap_do_conc_load(brd, uaddr, fw->size)
-			release_firmware(fw);
-		}
-	}
-#endif
-	/*
-	 * Do tty device initialization.
-	 */
-	ret = dgap_tty_init(brd); 
-	if (ret < 0) {
-		dgap_tty_uninit(brd);
-        	printk("DGAP: dgap_firmware_load: Can't init tty devices (%d)\n", ret);
-		return -EIO;
-	}
-
-	dgap_sysfs_create(brd);
-
-	brd->state = BOARD_READY;
-	brd->dpastatus = BD_RUNNING;
-
-	return 0;
-}
-
-/*
- * Remap PCI memory.
- */
-static int dgap_do_remap(struct board_t *brd)
-{
-	if (!brd || brd->magic != DGAP_BOARD_MAGIC)
-		return -ENXIO;
-
-	if (!request_mem_region(brd->membase, 0x200000, "dgap")) {
-		APR(("dgap: mem_region %lx already in use.\n", brd->membase));
-		return -ENOMEM;
-        }
-
-	if (!request_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000, "dgap")) {
-		APR(("dgap: mem_region IO %lx already in use.\n",
-			brd->membase + PCI_IO_OFFSET));
-		release_mem_region(brd->membase, 0x200000);
-		return -ENOMEM;
-        }
-
-	brd->re_map_membase = ioremap(brd->membase, 0x200000);
-	if (!brd->re_map_membase) {
-		APR(("dgap: ioremap mem %lx cannot be mapped.\n", brd->membase));
-		release_mem_region(brd->membase, 0x200000);
-		release_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000);
-		return -ENOMEM;
-	}
-
-	brd->re_map_port = ioremap((brd->membase + PCI_IO_OFFSET), 0x200000);
-	if (!brd->re_map_port) {
-		release_mem_region(brd->membase, 0x200000);
-		release_mem_region(brd->membase + PCI_IO_OFFSET, 0x200000);
-		iounmap(brd->re_map_membase);
-		APR(("dgap: ioremap IO mem %lx cannot be mapped.\n",
-			brd->membase + PCI_IO_OFFSET));
-		return -ENOMEM;
-	}
-
-	DPR_INIT(("remapped io: 0x%p  remapped mem: 0x%p\n",
-		brd->re_map_port, brd->re_map_membase));
-	return 0;
-}
-
-/*****************************************************************************
-*
-* Function:
-*                                       
-*    dgap_poll_handler
-*
-* Author:
-*
-*    Scott H Kilau
-*       
-* Parameters:
-*
-*    dummy -- ignored                    
-*
-* Return Values:
-*
-*    none
-*
-* Description:   
-*                                       
-*    As each timer expires, it determines (a) whether the "transmit"
-*    waiter needs to be woken up, and (b) whether the poller needs to
-*    be rescheduled.
-*
-******************************************************************************/
-
-static void dgap_poll_handler(ulong dummy)
-{
-	int i;
-        struct board_t *brd;
-        unsigned long lock_flags;
-        ulong new_time;
-
-	dgap_poll_counter++;
-
-	/*
-	 * Do not start the board state machine until
-	 * driver tells us its up and running, and has
-	 * everything it needs.
-	 */
-	if (dgap_driver_state != DRIVER_READY)
-		goto schedule_poller;
-	
-	/*
-	 * If we have just 1 board, or the system is not SMP,
-	 * then use the typical old style poller.
-	 * Otherwise, use our new tasklet based poller, which should
-	 * speed things up for multiple boards.
-	 */
-	if ((dgap_NumBoards == 1) || (num_online_cpus() <= 1)) {
-		for (i = 0; i < dgap_NumBoards; i++) {
-
-			brd = dgap_Board[i];
-
-			if (brd->state == BOARD_FAILED) 
-				continue;
-			
-			if (!brd->intr_running) 
-				/* Call the real board poller directly */
-				dgap_poll_tasklet((unsigned long) brd);
-			
-		}
-	} else {
-		/* Go thru each board, kicking off a tasklet for each if needed */
-		for (i = 0; i < dgap_NumBoards; i++) {
-			brd = dgap_Board[i];
-
-			/*
-			 * Attempt to grab the board lock.
-			 *
-			 * If we can't get it, no big deal, the next poll will get it.
-			 * Basically, I just really don't want to spin in here, because I want
-			 * to kick off my tasklets as fast as I can, and then get out the poller.
-			 */
-			if (!spin_trylock(&brd->bd_lock)) 
-				continue;
-
-			/* If board is in a failed state, don't bother scheduling a tasklet */
-			if (brd->state == BOARD_FAILED) {
-				spin_unlock(&brd->bd_lock);
-				continue;
-			}
-
-			/* Schedule a poll helper task */
-			if (!brd->intr_running) 
-				tasklet_schedule(&brd->helper_tasklet);
-
-			/*
-			 * Can't do DGAP_UNLOCK here, as we don't have
-			 * lock_flags because we did a trylock above.
-			 */
-			spin_unlock(&brd->bd_lock);
-		}
-	}
-
-schedule_poller:
-
-	/*
-	 * Schedule ourself back at the nominal wakeup interval.
-	 */
-	DGAP_LOCK(dgap_poll_lock, lock_flags);
-	dgap_poll_time +=  dgap_jiffies_from_ms(dgap_poll_tick);
-
-	new_time = dgap_poll_time - jiffies;
-
-	if ((ulong) new_time >= 2 * dgap_poll_tick) 
-		dgap_poll_time = jiffies +  dgap_jiffies_from_ms(dgap_poll_tick);
-
-	dgap_poll_timer.function = dgap_poll_handler;
-	dgap_poll_timer.data = 0;
-	dgap_poll_timer.expires = dgap_poll_time;
-	DGAP_UNLOCK(dgap_poll_lock, lock_flags);
-
-	if (!dgap_poll_stop)
-		add_timer(&dgap_poll_timer);
-}
-
-/*
- * dgap_intr()
- *
- * Driver interrupt handler.
- */
-static irqreturn_t dgap_intr(int irq, void *voidbrd)
-{
-	struct board_t *brd = (struct board_t *) voidbrd;
-
-	if (!brd) {
-		APR(("Received interrupt (%d) with null board associated\n", irq));
-		return IRQ_NONE;
-	}
-
-	/*
-	 * Check to make sure its for us.
-	 */
-	if (brd->magic != DGAP_BOARD_MAGIC) {
-		APR(("Received interrupt (%d) with a board pointer that wasn't ours!\n", irq));
-		return IRQ_NONE;
-	}
-
-	brd->intr_count++;
-
-	/*
-	 * Schedule tasklet to run at a better time.
-	 */
-	tasklet_schedule(&brd->helper_tasklet);
-	return IRQ_HANDLED;
-}
-
-/*
- * dgap_init_globals()
- *
- * This is where we initialize the globals from the static insmod
- * configuration variables.  These are declared near the head of
- * this file.
- */
-static void dgap_init_globals(void)
-{
-	int i = 0;
-
-	dgap_rawreadok		= rawreadok;
-	dgap_debug		= debug;
-
-	for (i = 0; i < MAXBOARDS; i++) 
-		dgap_Board[i] = NULL;
-
-	init_timer(&dgap_poll_timer); 
-
-	init_waitqueue_head(&dgap_dl_wait);
-	dgap_dl_action = 0;
-}
-
-/************************************************************************
- *
- * Utility functions
- *
- ************************************************************************/
-
-/*
- * dgap_driver_kzmalloc()
- *
- * Malloc and clear memory,
- */
-void *dgap_driver_kzmalloc(size_t size, int priority)
-{
- 	void *p = kmalloc(size, priority);
-	if(p)
-		memset(p, 0, size);
-	return(p);
-}
-
-/*
- * dgap_mbuf()
- *
- * Used to print to the message buffer during board init.
- */
-static void dgap_mbuf(struct board_t *brd, const char *fmt, ...) {
-	va_list		ap;
-	char		buf[1024];
-	int		i;
-	unsigned long	flags;
-	size_t		length;
-
-	DGAP_LOCK(dgap_global_lock, flags);
-
-	/* Format buf using fmt and arguments contained in ap. */
-	va_start(ap, fmt);
-	i = vsnprintf(buf, sizeof(buf), fmt,  ap);
-	va_end(ap);
-
-	DPR((buf));
-
-	if (!brd || !brd->msgbuf) {
-		printk("%s", buf);
-		DGAP_UNLOCK(dgap_global_lock, flags);
-		return;
-	}
-
-	length = strlen(buf) + 1;
-	if (brd->msgbuf - brd->msgbuf_head < length)
-		length = brd->msgbuf - brd->msgbuf_head;
-	memcpy(brd->msgbuf, buf, length);
-	brd->msgbuf += length;
-
-	DGAP_UNLOCK(dgap_global_lock, flags);
-}
-
-/*
- * dgap_ms_sleep()
- *
- * Put the driver to sleep for x ms's
- *
- * Returns 0 if timed out, !0 (showing signal) if interrupted by a signal.
- */
-int dgap_ms_sleep(ulong ms)
-{
-	current->state = TASK_INTERRUPTIBLE;
-	schedule_timeout((ms * HZ) / 1000);
-	return (signal_pending(current));
-}
-
-/*
- *      dgap_ioctl_name() : Returns a text version of each ioctl value.
- */
-char *dgap_ioctl_name(int cmd)
-{
-	switch(cmd) {
-
-	case TCGETA:		return("TCGETA");
-	case TCGETS:		return("TCGETS");
-	case TCSETA:		return("TCSETA");
-	case TCSETS:		return("TCSETS");
-	case TCSETAW:		return("TCSETAW");
-	case TCSETSW:		return("TCSETSW");
-	case TCSETAF:		return("TCSETAF");
-	case TCSETSF:		return("TCSETSF");
-	case TCSBRK:		return("TCSBRK");
-	case TCXONC:		return("TCXONC");
-	case TCFLSH:		return("TCFLSH");
-	case TIOCGSID:		return("TIOCGSID");
-
-	case TIOCGETD:		return("TIOCGETD");
-	case TIOCSETD:		return("TIOCSETD");
-	case TIOCGWINSZ:	return("TIOCGWINSZ");
-	case TIOCSWINSZ:	return("TIOCSWINSZ");
-
-	case TIOCMGET:		return("TIOCMGET");
-	case TIOCMSET:		return("TIOCMSET");
-	case TIOCMBIS:		return("TIOCMBIS");
-	case TIOCMBIC:		return("TIOCMBIC");
-
-	/* from digi.h */
-	case DIGI_SETA:		return("DIGI_SETA");
-	case DIGI_SETAW:	return("DIGI_SETAW");
-	case DIGI_SETAF:	return("DIGI_SETAF");
-	case DIGI_SETFLOW:	return("DIGI_SETFLOW");
-	case DIGI_SETAFLOW:	return("DIGI_SETAFLOW");
-	case DIGI_GETFLOW:	return("DIGI_GETFLOW");
-	case DIGI_GETAFLOW:	return("DIGI_GETAFLOW");
-	case DIGI_GETA:		return("DIGI_GETA");
-	case DIGI_GEDELAY:	return("DIGI_GEDELAY");
-	case DIGI_SEDELAY:	return("DIGI_SEDELAY");
-	case DIGI_GETCUSTOMBAUD: return("DIGI_GETCUSTOMBAUD");
-	case DIGI_SETCUSTOMBAUD: return("DIGI_SETCUSTOMBAUD");
-	case TIOCMODG:		return("TIOCMODG");
-	case TIOCMODS:		return("TIOCMODS");
-	case TIOCSDTR:		return("TIOCSDTR");
-	case TIOCCDTR:		return("TIOCCDTR");
-
-	default:		return("unknown");
-	}
-}
- 
-/*
- * Loads the dgap.conf config file from the user.
- */
-void dgap_do_config_load(uchar __user *uaddr, int len)
-{
-	int orig_len = len;
-	char *to_addr;
-	uchar __user *from_addr = uaddr;
-	char buf[U2BSIZE];
-	int n;
-
-	to_addr = dgap_config_buf = dgap_driver_kzmalloc(len + 1, GFP_ATOMIC);
-	if (!dgap_config_buf) {
-		DPR_INIT(("dgap_do_config_load - unable to allocate memory for file\n"));
-		dgap_driver_state = DRIVER_NEED_CONFIG_LOAD;
-		return;
-	}
-
-	n = U2BSIZE;
-	while (len) {
-
-		if (n > len)
-			n = len;
-
-		if (copy_from_user((char *) &buf, from_addr, n) == -1)
-			return;
-
-		/* Copy data from buffer to kernel memory */
-		memcpy(to_addr, buf, n);
-
-		/* increment counts */
-		len -= n;
-		to_addr += n;
-		from_addr += n;
-		n = U2BSIZE;
-        }
-
-	dgap_config_buf[orig_len] = '\0';
-
-	to_addr = dgap_config_buf;
-	dgap_parsefile(&to_addr, TRUE);
-
-	DPR_INIT(("dgap_config_load() finish\n"));
-
-	return;
-}
-
-static int dgap_after_config_loaded(int board)
-{
-        int ret = 0;
-
-	/*
-	 * Initialize KME waitqueues...
-	 */
-	init_waitqueue_head(&(dgap_Board[board]->kme_wait));
-
-	/*
-	 * allocate flip buffer for board.
-	 */
-	dgap_Board[board]->flipbuf = dgap_driver_kzmalloc(MYFLIPLEN, GFP_ATOMIC);
-	if (!dgap_Board[board]->flipbuf) {
-		ret = -ENOMEM;
-		goto out;
-	}
-	dgap_Board[board]->flipflagbuf = dgap_driver_kzmalloc(MYFLIPLEN, GFP_ATOMIC);
-	if (!dgap_Board[board]->flipflagbuf) 
-		ret = -ENOMEM;
-
-    out:
-        return ret;
-}
-
-/*
- * Create pr and tty device entries
- */
-static void dgap_sysfs_create(struct board_t *brd)
-{
-	struct channel_t *ch;
-	int j = 0;
-
-	ch = brd->channels[0];
-	for (j = 0; j < brd->nasync; j++, ch = brd->channels[j]) {
-		struct device *classp;
-		classp = tty_register_device(brd->SerialDriver, j, &(ch->ch_bd->pdev->dev));
-		ch->ch_tun.un_sysfs = classp;
-		dgap_create_tty_sysfs(&ch->ch_tun, classp);
-
-		classp = tty_register_device(brd->PrintDriver, j, &(ch->ch_bd->pdev->dev));
-		ch->ch_pun.un_sysfs = classp;
-		dgap_create_tty_sysfs(&ch->ch_pun, classp);
-	}
-	dgap_create_ports_sysfiles(brd);
-}
-
-/*
- * Copies the BIOS code from the user to the board,
- * and starts the BIOS running.
- */
-static void dgap_do_bios_load(struct board_t *brd, uchar *ubios, int len)
-{
-	uchar *addr;
-	uint offset;
-	int i;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
-		return;
-
-	DPR_INIT(("dgap_do_bios_load() start\n"));
-
-	addr = brd->re_map_membase;
-
-	/*
-	 * clear POST area
-	 */
-	for (i = 0; i < 16; i++)
-		writeb(0, addr + POSTAREA + i);
-                                
-	/*
-	 * Download bios
-	 */
-	offset = 0x1000;
-	memcpy_toio(addr + offset, ubios, len);
-
-	writel(0x0bf00401, addr);
-	writel(0, (addr + 4));
-
-	/* Clear the reset, and change states. */
-	writeb(FEPCLR, brd->re_map_port);
-}
-
-/*
- * Checks to see if the BIOS completed running on the card.
- */
-static void dgap_do_wait_for_bios(struct board_t *brd)
-{
-	uchar *addr;
-	u16 word;
-	u16 err1;
-	u16 err2;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
-		return;
-	
-	addr = brd->re_map_membase;
-	word = readw(addr + POSTAREA);
-
-	/*
-	 * It can take 5-6 seconds for a board to
-	 * pass the bios self test and post results.
-	 * Give it 10 seconds.
-	 */
-	brd->wait_for_bios = 0;
-	while (brd->wait_for_bios < 1000) {
-		/* Check to see if BIOS thinks board is good. (GD). */
-		if (word == *(u16 *) "GD") {
-			DPR_INIT(("GOT GD in memory, moving states.\n"));
-			brd->state = FINISHED_BIOS_LOAD;
-			return;
-		}
-		msleep_interruptible(10);
-		brd->wait_for_bios++;
-		word = readw(addr + POSTAREA);
-	}
-
-	/* Gave up on board after too long of time taken */
-	err1 = readw(addr + SEQUENCE);
-	err2 = readw(addr + ERROR);
-	APR(("***WARNING*** %s failed diagnostics.  Error #(%x,%x).\n",
-		brd->name, err1, err2));
-	brd->state = BOARD_FAILED;
-	brd->dpastatus = BD_NOBIOS;
-}
-
-/*
- * Copies the FEP code from the user to the board,
- * and starts the FEP running.
- */
-static void dgap_do_fep_load(struct board_t *brd, uchar *ufep, int len)
-{
-	uchar *addr;
-	uint offset;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
-		return;
-
-	addr = brd->re_map_membase;
-
-	DPR_INIT(("dgap_do_fep_load() for board %s : start\n", brd->name));
-
-	/*
-	 * Download FEP
-	 */
-	offset = 0x1000;
-	memcpy_toio(addr + offset, ufep, len);
-
-	/*
-	 * If board is a concentrator product, we need to give
-	 * it its config string describing how the concentrators look.
-	 */
-	if ((brd->type == PCX) || (brd->type == PEPC)) {
-		uchar string[100];
-		uchar *config, *xconfig;
-		int i = 0;
-
-		xconfig = dgap_create_config_string(brd, string);
-
-		/* Write string to board memory */
-		config = addr + CONFIG;
-		for (; i < CONFIGSIZE; i++, config++, xconfig++) {
-			writeb(*xconfig, config);
-			if ((*xconfig & 0xff) == 0xff)
-				break;
-		}
-	}
-
-	writel(0xbfc01004, (addr + 0xc34));
-	writel(0x3, (addr + 0xc30));
-
-	DPR_INIT(("dgap_do_fep_load() for board %s : finish\n", brd->name));
-}
-
-/*
- * Waits for the FEP to report thats its ready for us to use.
- */
-void dgap_do_wait_for_fep(struct board_t *brd)
-{
-	uchar *addr;
-	u16 word;
-	u16 err1;
-	u16 err2;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
-		return;
-
-	addr = brd->re_map_membase;
-	word = readw(addr + FEPSTAT);
-
-	/*
-	 * It can take 2-3 seconds for the FEP to
-         * be up and running. Give it 5 secs.
-	 */
-	brd->wait_for_fep = 0;
-	while (brd->wait_for_fep < 500) {
-		/* Check to see if FEP is up and running now. */
-		if (word == *(u16 *) "OS") {
-			DPR_INIT(("GOT OS in memory for board %s, moving states.\n", brd->name));
-			brd->state = FINISHED_FEP_LOAD;
-			/*
-		 	* Check to see if the board can support FEP5+ commands.
-		 	*/
-			word = readw(addr + FEP5_PLUS);
-			if (word == *(u16 *) "5A") {
-				DPR_INIT(("GOT 5A in memory for board %s, board supports extended FEP5 commands.\n", brd->name));
-				brd->bd_flags |= BD_FEP5PLUS;
-			}
-
-			return;
-		}
-		msleep_interruptible(10);
-		brd->wait_for_fep++;
-		word = readw(addr + FEPSTAT);
-	}
-
-	/* Gave up on board after too long of time taken */
-	err1 = readw(addr + SEQUENCE);
-	err2 = readw(addr + ERROR);
-	APR(("***WARNING*** FEPOS for %s not functioning.  Error #(%x,%x).\n",
-		brd->name, err1, err2));
-	brd->state = BOARD_FAILED;
-	brd->dpastatus = BD_NOFEP;
-
-	DPR_INIT(("dgap_do_wait_for_fep() for board %s : finish\n", brd->name));
-}
-
-/*
- * Physically forces the FEP5 card to reset itself.
- */
-static void dgap_do_reset_board(struct board_t *brd)
-{
-	uchar check;
-	u32 check1;
-	u32 check2;
-	int i = 0;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase || !brd->re_map_port) {
-		DPR_INIT(("dgap_do_reset_board() start. bad values. brd: %p mem: %p io: %p\n", 
-			brd, brd ? brd->re_map_membase : 0, brd ? brd->re_map_port : 0));
-		return;
-	}
-
-	DPR_INIT(("dgap_do_reset_board() start. io: %p\n", brd->re_map_port));
-
-	/* FEPRST does not vary among supported boards */
-	writeb(FEPRST, brd->re_map_port);
-
-	for (i = 0; i <= 1000; i++) {
-		check = readb(brd->re_map_port) & 0xe;
-		if (check == FEPRST)
-			break;
-		udelay(10);
-
-	}
-	if (i > 1000) {
-		APR(("*** WARNING *** Board not resetting...  Failing board.\n"));
-		brd->state = BOARD_FAILED;
-		brd->dpastatus = BD_NOFEP;
-		goto failed;
-	}
-
-	/*
-	 * Make sure there really is memory out there.
-	 */
-	writel(0xa55a3cc3, (brd->re_map_membase + LOWMEM));
-	writel(0x5aa5c33c, (brd->re_map_membase + HIGHMEM));
-	check1 = readl(brd->re_map_membase + LOWMEM);
-	check2 = readl(brd->re_map_membase + HIGHMEM);
-
-	if ((check1 != 0xa55a3cc3) || (check2 != 0x5aa5c33c)) {
-		APR(("*** Warning *** No memory at %p for board.\n", brd->re_map_membase));
-		brd->state = BOARD_FAILED;
-		brd->dpastatus = BD_NOFEP;
-		goto failed;
-	}
-
-	if (brd->state != BOARD_FAILED)
-		brd->state = FINISHED_RESET;
-
-failed:
-	DPR_INIT(("dgap_do_reset_board() finish\n"));
-}
-
-#ifdef DIGI_CONCENTRATORS_SUPPORTED
-/*
- * Sends a concentrator image into the FEP5 board.  FIXME: 
- */
-void dgap_do_conc_load(struct board_t *brd, uchar *uaddr, int len)
-{
-	char *vaddr;
-	u16 offset = 0;
-	struct downld_t *to_dp;
-
-	if (!brd || (brd->magic != DGAP_BOARD_MAGIC) || !brd->re_map_membase)
-		return;
-
-	vaddr = brd->re_map_membase;
-
-	offset = readw((u16 *) (vaddr + DOWNREQ));
-	to_dp = (struct downld_t *) (vaddr + (int) offset);
-	memcpy_toio(to_dp, uaddr, len);
-
-	/* Tell card we have data for it */
-	writew(0, vaddr + (DOWNREQ));
-}
-#endif
-
-#define EXPANSION_ROM_SIZE	(64 * 1024)
-#define FEP5_ROM_MAGIC		(0xFEFFFFFF)
-
-static void dgap_get_vpd(struct board_t *brd)
-{
-	u32 magic;
-	u32 base_offset;
-	u16 rom_offset;
-	u16 vpd_offset;
-	u16 image_length;
-	u16 i;
-	uchar byte1;
-	uchar byte2;
-
-	/*
-	 * Poke the magic number at the PCI Rom Address location.
-	 * If VPD is supported, the value read from that address
-	 * will be non-zero.
-	 */
-	magic = FEP5_ROM_MAGIC;
-	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
-	pci_read_config_dword(brd->pdev, PCI_ROM_ADDRESS, &magic);
-
-	/* VPD not supported, bail */
-	if (!magic)
-		return;
-
-	/*
-	 * To get to the OTPROM memory, we have to send the boards base
-         * address or'ed with 1 into the PCI Rom Address location.
-	 */
-	magic = brd->membase | 0x01;
-	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
-	pci_read_config_dword(brd->pdev, PCI_ROM_ADDRESS, &magic);
-
-	byte1 = readb(brd->re_map_membase);
-	byte2 = readb(brd->re_map_membase + 1);
-
-	/*
-	 * If the board correctly swapped to the OTPROM memory,
-	 * the first 2 bytes (header) should be 0x55, 0xAA
-	 */
-	if (byte1 == 0x55 && byte2 == 0xAA) {
-
-		base_offset = 0;
-
-		/*
-		 * We have to run through all the OTPROM memory looking
-		 * for the VPD offset.
-		 */
-		while (base_offset <= EXPANSION_ROM_SIZE) {
-                
-			/*
-			 * Lots of magic numbers here.
-			 *
-			 * The VPD offset is located inside the ROM Data Structure.
-			 * We also have to remember the length of each
-			 * ROM Data Structure, so we can "hop" to the next
-			 * entry if the VPD isn't in the current
-			 * ROM Data Structure.
-			 */
-			rom_offset = readw(brd->re_map_membase + base_offset + 0x18);
-			image_length = readw(brd->re_map_membase + rom_offset + 0x10) * 512;
-			vpd_offset = readw(brd->re_map_membase + rom_offset + 0x08);
-
-			/* Found the VPD entry */
-			if (vpd_offset)
-				break;
-
-			/* We didn't find a VPD entry, go to next ROM entry. */
-			base_offset += image_length;
-
-			byte1 = readb(brd->re_map_membase + base_offset);
-			byte2 = readb(brd->re_map_membase + base_offset + 1);
-
-			/*
-			 * If the new ROM offset doesn't have 0x55, 0xAA
-			 * as its header, we have run out of ROM.
-			 */
-			if (byte1 != 0x55 || byte2 != 0xAA)
-				break;
-		}
-
-		/*
-		 * If we have a VPD offset, then mark the board
-		 * as having a valid VPD, and copy VPDSIZE (512) bytes of
-		 * that VPD to the buffer we have in our board structure.
-		 */
-		if (vpd_offset) {
-			brd->bd_flags |= BD_HAS_VPD;
-			for (i = 0; i < VPDSIZE; i++)
-				brd->vpd[i] = readb(brd->re_map_membase + vpd_offset + i);
-		}
-	}
-
-	/*
-	 * We MUST poke the magic number at the PCI Rom Address location again.
-	 * This makes the card report the regular board memory back to us,
-	 * rather than the OTPROM memory.
-	 */
-	magic = FEP5_ROM_MAGIC;
-	pci_write_config_dword(brd->pdev, PCI_ROM_ADDRESS, magic);
-}
-
-/*
- * Our board poller function.
- */
-void dgap_poll_tasklet(unsigned long data)
-{
-        struct board_t *bd = (struct board_t *) data;
-	ulong  lock_flags;
-	ulong  lock_flags2;
-	char *vaddr;
-	u16 head, tail;
-
-	if (!bd || (bd->magic != DGAP_BOARD_MAGIC)) {
-		APR(("dgap_poll_tasklet() - NULL or bad bd.\n"));
-		return;
-	}
-
-	if (bd->inhibit_poller)
-		return;
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-
-	vaddr = bd->re_map_membase;
-
-	/*
-	 * If board is ready, parse deeper to see if there is anything to do.
-	 */
-	if (bd->state == BOARD_READY) {
-
-		struct ev_t *eaddr = NULL;
-
-		if (!bd->re_map_membase) {
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			return;
-		}
-		if (!bd->re_map_port) {
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			return;
-		}
-
-		if (!bd->nasync) {
-			goto out;
-		}
-
-		eaddr = (struct ev_t *) (vaddr + EVBUF);
-
-		/* Get our head and tail */
-		head = readw(&(eaddr->ev_head));
-		tail = readw(&(eaddr->ev_tail));
-
-		/*
-		 * If there is an event pending. Go service it.
-		 */
-		if (head != tail) {
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			dgap_event(bd);
-			DGAP_LOCK(bd->bd_lock, lock_flags);
-		}
-
-out:
-		/*
-		 * If board is doing interrupts, ACK the interrupt.
-		 */
-		if (bd && bd->intr_running) {
-			readb(bd->re_map_port + 2);
-		}
-
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return;
-	}
-
-	/* Our state machine to get the board up and running */
-
-	/* Reset board */
-	if (bd->state == NEED_RESET) {
-
-		/* Get VPD info */
-		dgap_get_vpd(bd);
-
-		dgap_do_reset_board(bd);
-	}
-
-	/* Move to next state */
-	if (bd->state == FINISHED_RESET) {
-		bd->state = NEED_CONFIG;
-	}
-
-	if (bd->state == NEED_CONFIG) {
-		/*
-		 * Match this board to a config the user created for us.
-		 */
-		bd->bd_config = dgap_find_config(bd->type, bd->pci_bus, bd->pci_slot);
-
-		/*
-		 * Because the 4 port Xr products share the same PCI ID
-		 * as the 8 port Xr products, if we receive a NULL config
-		 * back, and this is a PAPORT8 board, retry with a
-		 * PAPORT4 attempt as well.
-		 */
-		if (bd->type == PAPORT8 && !bd->bd_config) {
-			bd->bd_config = dgap_find_config(PAPORT4, bd->pci_bus, bd->pci_slot);
-		}
-
-		/*
-		 * Register the ttys (if any) into the kernel.
-		 */
-		if (bd->bd_config) {
-			bd->state = FINISHED_CONFIG;
-		}
-		else {
-			bd->state = CONFIG_NOT_FOUND;
-		}
-	}
-
-	/* Move to next state */
-	if (bd->state == FINISHED_CONFIG) {
-		bd->state = NEED_DEVICE_CREATION;
-	}
-
-	/* Move to next state */
-	if (bd->state == NEED_DEVICE_CREATION) {
-		/*
-		 * Signal downloader, its got some work to do.
-		 */
-		DGAP_LOCK(dgap_dl_lock, lock_flags2);
-		if (dgap_dl_action != 1) {
-			dgap_dl_action = 1;
-			wake_up_interruptible(&dgap_dl_wait);
-		}
-		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
-	}
-
-	/* Move to next state */
-	if (bd->state == FINISHED_DEVICE_CREATION) {
-		bd->state = NEED_BIOS_LOAD;
-	}
-
-	/* Move to next state */
-	if (bd->state == NEED_BIOS_LOAD) {
-		/*
-		 * Signal downloader, its got some work to do.
-		 */
-		DGAP_LOCK(dgap_dl_lock, lock_flags2);
-		if (dgap_dl_action != 1) {
-			dgap_dl_action = 1;
-			wake_up_interruptible(&dgap_dl_wait);
-		}
-		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
-	}
-
-	/* Wait for BIOS to test board... */
-	if (bd->state == WAIT_BIOS_LOAD) {
-		dgap_do_wait_for_bios(bd);
-	}
-
-	/* Move to next state */
-	if (bd->state == FINISHED_BIOS_LOAD) {
-		bd->state = NEED_FEP_LOAD;
-
-		/*
-		 * Signal downloader, its got some work to do.
-		 */
-		DGAP_LOCK(dgap_dl_lock, lock_flags2);
-		if (dgap_dl_action != 1) {
-			dgap_dl_action = 1;
-			wake_up_interruptible(&dgap_dl_wait);
-		}
-		DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
-	}
-
-	/* Wait for FEP to load on board... */
-	if (bd->state == WAIT_FEP_LOAD) {
-		dgap_do_wait_for_fep(bd);
-	}
-
-
-	/* Move to next state */
-	if (bd->state == FINISHED_FEP_LOAD) {
-
-		/*
-		 * Do tty device initialization.
-		 */
-		int rc = dgap_tty_init(bd);
-
-		if (rc < 0) {
-			dgap_tty_uninit(bd);
-			APR(("Can't init tty devices (%d)\n", rc));
-			bd->state = BOARD_FAILED;
-			bd->dpastatus = BD_NOFEP;
-		}
-		else {
-			bd->state = NEED_PROC_CREATION;
-
-			/*
-			 * Signal downloader, its got some work to do.
-			 */
-			DGAP_LOCK(dgap_dl_lock, lock_flags2);
-			if (dgap_dl_action != 1) {
-				dgap_dl_action = 1;
-				wake_up_interruptible(&dgap_dl_wait);
-			}
-			DGAP_UNLOCK(dgap_dl_lock, lock_flags2);
-		}
-	}
-
-	/* Move to next state */
-	if (bd->state == FINISHED_PROC_CREATION) {
-
-		bd->state = BOARD_READY;
-		bd->dpastatus = BD_RUNNING;
-
-		/*
-		 * If user requested the board to run in interrupt mode,
-		 * go and set it up on the board.
-		 */
-		if (bd->intr_used) {
-			writew(1, (bd->re_map_membase + ENABLE_INTR));
-			/*
-			 * Tell the board to poll the UARTS as fast as possible.
-			 */
-			writew(FEPPOLL_MIN, (bd->re_map_membase + FEPPOLL));
-			bd->intr_running = 1;
-		}
-
-		/* Wake up anyone waiting for board state to change to ready */
-		wake_up_interruptible(&bd->state_wait);
-	}
-
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-}
-
-/*=======================================================================
- *
- *      dgap_cmdb - Sends a 2 byte command to the FEP.
- *
- *              ch      - Pointer to channel structure.
- *              cmd     - Command to be sent.
- *              byte1   - Integer containing first byte to be sent.
- *              byte2   - Integer containing second byte to be sent.
- *              ncmds   - Wait until ncmds or fewer cmds are left
- *                        in the cmd buffer before returning.
- *
- *=======================================================================*/
-void dgap_cmdb(struct channel_t *ch, uchar cmd, uchar byte1, uchar byte2, uint ncmds)
-{                       
-	char		*vaddr = NULL;
-	struct cm_t	*cm_addr = NULL;
-	uint		count;
-	uint		n;
-	u16		head;
-        u16		tail;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	/*
-	 * Check if board is still alive.
-	 */
-	if (ch->ch_bd->state == BOARD_FAILED) {
-		DPR_CORE(("%s:%d board is in failed state.\n", __FILE__, __LINE__));
-		return;
-        }               
-
-	/*
-	 * Make sure the pointers are in range before
-	 * writing to the FEP memory.
-	 */
-	vaddr = ch->ch_bd->re_map_membase;
-
-	if (!vaddr)
-		return;
-
-	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
-	head = readw(&(cm_addr->cm_head));
-
-	/* 
-	 * Forget it if pointers out of range.
-	 */
-	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
-		DPR_CORE(("%s:%d pointers out of range, failing board!\n", __FILE__, __LINE__));
-		ch->ch_bd->state = BOARD_FAILED;
-		return; 
-	}
-
-	/*
-	 * Put the data in the circular command buffer.
-	 */
-	writeb(cmd, (char *) (vaddr + head + CMDSTART + 0));
-	writeb((uchar) ch->ch_portnum, (char *) (vaddr + head + CMDSTART + 1));
-	writeb(byte1, (char *) (vaddr + head + CMDSTART + 2));
-	writeb(byte2, (char *) (vaddr + head + CMDSTART + 3));
-
-	head = (head + 4) & (CMDMAX - CMDSTART - 4);
-
-	writew(head, &(cm_addr->cm_head));
-
-	/*
-	 * Wait if necessary before updating the head  
-	 * pointer to limit the number of outstanding
-	 * commands to the FEP.   If the time spent waiting
-	 * is outlandish, declare the FEP dead.
-	 */
-	for (count = dgap_count ;;) {
-
-		head = readw(&(cm_addr->cm_head));
-		tail = readw(&(cm_addr->cm_tail));
-
-		n = (head - tail) & (CMDMAX - CMDSTART - 4);
-
-		if (n <= ncmds * sizeof(struct cm_t))
-			break;
-
-		if (--count == 0) {
-			DPR_CORE(("%s:%d failing board.\n",__FILE__, __LINE__));
-			ch->ch_bd->state = BOARD_FAILED;
-			return;
-		}
-		udelay(10);
-	}  
-}
-
-/*=======================================================================
- *
- *      dgap_cmdw - Sends a 1 word command to the FEP.
- *      
- *              ch      - Pointer to channel structure.
- *              cmd     - Command to be sent.
- *              word    - Integer containing word to be sent.
- *              ncmds   - Wait until ncmds or fewer cmds are left
- *                        in the cmd buffer before returning.
- *
- *=======================================================================*/
-void dgap_cmdw(struct channel_t *ch, uchar cmd, u16 word, uint ncmds)
-{
-	char		*vaddr = NULL;
-	struct cm_t	*cm_addr = NULL;
-	uint		count;
-	uint		n;
-	u16		head;
-	u16		tail;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	/*
-	 * Check if board is still alive.
-	 */
-	if (ch->ch_bd->state == BOARD_FAILED) {
-		DPR_CORE(("%s:%d board is failed!\n", __FILE__, __LINE__));
-		return;
-	}
-
-	/*
-	 * Make sure the pointers are in range before
-	 * writing to the FEP memory.
-	 */
-	vaddr = ch->ch_bd->re_map_membase;
-	if (!vaddr)
-		return;
-
-	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
-	head = readw(&(cm_addr->cm_head));
-
-	/* 
-	 * Forget it if pointers out of range.
-	 */
-	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
-		DPR_CORE(("%s:%d Pointers out of range.  Failing board.\n",__FILE__, __LINE__));
-		ch->ch_bd->state = BOARD_FAILED;
-		return;
-	}
-
-	/*
-	 * Put the data in the circular command buffer.
-	 */
-	writeb(cmd, (char *) (vaddr + head + CMDSTART + 0));
-	writeb((uchar) ch->ch_portnum, (char *) (vaddr + head + CMDSTART + 1));
-	writew((u16) word, (char *) (vaddr + head + CMDSTART + 2));
-
-	head = (head + 4) & (CMDMAX - CMDSTART - 4);
-
-	writew(head, &(cm_addr->cm_head));
-
-	/*
-	 * Wait if necessary before updating the head
-	 * pointer to limit the number of outstanding  
-	 * commands to the FEP.   If the time spent waiting
-	 * is outlandish, declare the FEP dead.
-	 */
-	for (count = dgap_count ;;) {
-
-		head = readw(&(cm_addr->cm_head));
-		tail = readw(&(cm_addr->cm_tail));
-
-		n = (head - tail) & (CMDMAX - CMDSTART - 4);
-
-		if (n <= ncmds * sizeof(struct cm_t))
-			break;
-
-		if (--count == 0) {
-			DPR_CORE(("%s:%d Failing board.\n",__FILE__, __LINE__));
-			ch->ch_bd->state = BOARD_FAILED;
-			return;
-		}
-		udelay(10);
-	}  
-}
-
-/*=======================================================================
- *
- *      dgap_cmdw_ext - Sends a extended word command to the FEP.
- *      
- *              ch      - Pointer to channel structure.
- *              cmd     - Command to be sent.
- *              word    - Integer containing word to be sent.
- *              ncmds   - Wait until ncmds or fewer cmds are left
- *                        in the cmd buffer before returning.
- *
- *=======================================================================*/
-static void dgap_cmdw_ext(struct channel_t *ch, u16 cmd, u16 word, uint ncmds)
-{
-	char		*vaddr = NULL;
-	struct cm_t	*cm_addr = NULL;
-	uint		count;
-	uint		n;
-	u16		head;
-	u16		tail;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	/*
-	 * Check if board is still alive.
-	 */
-	if (ch->ch_bd->state == BOARD_FAILED) {
-		DPR_CORE(("%s:%d board is failed!\n", __FILE__, __LINE__));
-		return;
-	}
-
-	/*
-	 * Make sure the pointers are in range before
-	 * writing to the FEP memory.
-	 */
-	vaddr = ch->ch_bd->re_map_membase;
-	if (!vaddr)
-		return;
-
-	cm_addr = (struct cm_t *) (vaddr + CMDBUF);
-	head = readw(&(cm_addr->cm_head));
-
-	/* 
-	 * Forget it if pointers out of range.
-	 */
-	if (head >= (CMDMAX - CMDSTART) || (head & 03)) {
-		DPR_CORE(("%s:%d Pointers out of range.  Failing board.\n",__FILE__, __LINE__));
-		ch->ch_bd->state = BOARD_FAILED;
-		return;
-	}
-
-	/*
-	 * Put the data in the circular command buffer.
-	 */
-
-	/* Write an FF to tell the FEP that we want an extended command */
-	writeb((uchar) 0xff, (char *) (vaddr + head + CMDSTART + 0));
-
-	writeb((uchar) ch->ch_portnum, (uchar *) (vaddr + head + CMDSTART + 1));
-	writew((u16) cmd, (char *) (vaddr + head + CMDSTART + 2));
-
-	/*
-	 * If the second part of the command won't fit,
-	 * put it at the beginning of the circular buffer.
-	 */
-	if (((head + 4) >= ((CMDMAX - CMDSTART)) || (head & 03))) {
-		writew((u16) word, (char *) (vaddr + CMDSTART));
-	} else {
-		writew((u16) word, (char *) (vaddr + head + CMDSTART + 4));
-	}
-
-	head = (head + 8) & (CMDMAX - CMDSTART - 4);
-
-	writew(head, &(cm_addr->cm_head));
-
-	/*
-	 * Wait if necessary before updating the head
-	 * pointer to limit the number of outstanding  
-	 * commands to the FEP.   If the time spent waiting
-	 * is outlandish, declare the FEP dead.
-	 */
-	for (count = dgap_count ;;) {
-
-		head = readw(&(cm_addr->cm_head));
-		tail = readw(&(cm_addr->cm_tail));
-
-		n = (head - tail) & (CMDMAX - CMDSTART - 4);
-
-		if (n <= ncmds * sizeof(struct cm_t))
-			break;
-
-		if (--count == 0) {
-			DPR_CORE(("%s:%d Failing board.\n",__FILE__, __LINE__));
-			ch->ch_bd->state = BOARD_FAILED;
-			return;
-		}
-		udelay(10);
-	}  
-}
-
-/*=======================================================================
- *
- *      dgap_wmove - Write data to FEP buffer.
- *
- *              ch      - Pointer to channel structure.
- *              buf     - Poiter to characters to be moved.
- *              cnt     - Number of characters to move.
- *
- *=======================================================================*/
-void dgap_wmove(struct channel_t *ch, char *buf, uint cnt)
-{
-	int    n;
-	char   *taddr;
-	struct bs_t    *bs;
-	u16    head;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
- 
-	/*
-	 * Check parameters.
-	 */
-	bs   = ch->ch_bs;
-	head = readw(&(bs->tx_head));
-
-	/*
-	 * If pointers are out of range, just return.
-	 */
-	if ((cnt > ch->ch_tsize) || (unsigned)(head - ch->ch_tstart) >= ch->ch_tsize) {
-		DPR_CORE(("%s:%d pointer out of range", __FILE__, __LINE__));
-		return;
-	}
-
-	/*
-	 * If the write wraps over the top of the circular buffer,
-	 * move the portion up to the wrap point, and reset the
-	 * pointers to the bottom.
-	 */
-	n = ch->ch_tstart + ch->ch_tsize - head;
-
-	if (cnt >= n) {
-		cnt -= n;
-		taddr = ch->ch_taddr + head;
-		memcpy_toio(taddr, buf, n);
-		head = ch->ch_tstart;
-		buf += n;
-	}
-
-	/*
-	 * Move rest of data.
-	 */
-	taddr = ch->ch_taddr + head;
-	n = cnt;
-	memcpy_toio(taddr, buf, n);
-	head += cnt;
-
-	writew(head, &(bs->tx_head));
-}
-
-/*
- * Retrives the current custom baud rate from FEP memory,
- * and returns it back to the user.
- * Returns 0 on error.
- */
-uint dgap_get_custom_baud(struct channel_t *ch)
-{
-	uchar *vaddr;
-	ulong offset = 0;
-	uint value = 0;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC) {
-		return 0;
-	}
-
-	if (!ch->ch_bd || ch->ch_bd->magic != DGAP_BOARD_MAGIC) {
-		return 0;
-	}
-
-	if (!(ch->ch_bd->bd_flags & BD_FEP5PLUS))
-		return 0;
-
-	vaddr = ch->ch_bd->re_map_membase;
-
-	if (!vaddr)
-		return 0;
-
-	/*
-	 * Go get from fep mem, what the fep
-	 * believes the custom baud rate is. 
-	 */
-	offset = ((((*(unsigned short *)(vaddr + ECS_SEG)) << 4) +  
-		(ch->ch_portnum * 0x28) + LINE_SPEED));
-
-	value = readw(vaddr + offset);
-	return value;
-}
-
-/*
- * Calls the firmware to reset this channel.
- */
-void dgap_firmware_reset_port(struct channel_t *ch)
-{
-	dgap_cmdb(ch, CHRESET, 0, 0, 0);
-
-	/*
-	 * Now that the channel is reset, we need to make sure
-	 * all the current settings get reapplied to the port
-	 * in the firmware.
-	 *
-	 * So we will set the driver's cache of firmware
-	 * settings all to 0, and then call param.
-	 */
-	ch->ch_fepiflag = 0;
-	ch->ch_fepcflag = 0;
-	ch->ch_fepoflag = 0;
-	ch->ch_fepstartc = 0;
-	ch->ch_fepstopc = 0;
-	ch->ch_fepastartc = 0;
-	ch->ch_fepastopc = 0;
-	ch->ch_mostat = 0;
-	ch->ch_hflow = 0;
-}
-
-/*=======================================================================
- *      
- *      dgap_param - Set Digi parameters.
- *
- *              struct tty_struct *     - TTY for port.
- *
- *=======================================================================*/
-int dgap_param(struct tty_struct *tty)
-{
-	struct ktermios *ts;
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct bs_t   *bs;
-	struct un_t   *un;
-	u16	head;
-	u16	cflag;
-	u16	iflag;
-	uchar	mval;
-	uchar	hflow;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return -ENXIO;
-
-	un = (struct un_t *) tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return -ENXIO;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return -ENXIO;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return -ENXIO;
-
-        bs = ch->ch_bs;
-	if (!bs)
-		return -ENXIO;
-
-	DPR_PARAM(("param start: tdev: %x cflags: %x oflags: %x iflags: %x\n",
-		ch->ch_tun.un_dev, ch->ch_c_cflag, ch->ch_c_oflag, ch->ch_c_iflag));
-
-	ts = &tty->termios;
-
-	/*
-	 * If baud rate is zero, flush queues, and set mval to drop DTR.
-	 */
-	if ((ch->ch_c_cflag & (CBAUD)) == 0) {
-
-		/* flush rx */
-		head = readw(&(ch->ch_bs->rx_head));
-		writew(head, &(ch->ch_bs->rx_tail));
-
-		/* flush tx */
-		head = readw(&(ch->ch_bs->tx_head));
-		writew(head, &(ch->ch_bs->tx_tail));
-
-		ch->ch_flags |= (CH_BAUD0);
-
-		/* Drop RTS and DTR */
-		ch->ch_mval &= ~(D_RTS(ch)|D_DTR(ch));
-		mval = D_DTR(ch) | D_RTS(ch);
-		ch->ch_baud_info = 0;
-
-	} else if (ch->ch_custom_speed && (bd->bd_flags & BD_FEP5PLUS)) {
-		/*
-		 * Tell the fep to do the command
-		 */
-
-		DPR_PARAM(("param: Want %d speed\n", ch->ch_custom_speed));
-
-		dgap_cmdw_ext(ch, 0xff01, ch->ch_custom_speed, 0);
-
-		/*
-		 * Now go get from fep mem, what the fep
-		 * believes the custom baud rate is. 
-		 */
-		ch->ch_baud_info = ch->ch_custom_speed = dgap_get_custom_baud(ch);
-
-		DPR_PARAM(("param: Got %d speed\n", ch->ch_custom_speed));
-
-		/* Handle transition from B0 */   
-		if (ch->ch_flags & CH_BAUD0) {
-			ch->ch_flags &= ~(CH_BAUD0);
-			ch->ch_mval |= (D_RTS(ch)|D_DTR(ch));
-		}
-		mval = D_DTR(ch) | D_RTS(ch);
-
-	} else {
-		/*
-		 * Set baud rate, character size, and parity.
-		 */
-
-
-		int iindex = 0;
-		int jindex = 0;
-		int baud = 0;
-
-		ulong bauds[4][16] = {
-			{ /* slowbaud */
-				0,	50,	75,	110,
-				134,	150,	200,	300,
-				600,	1200,	1800,	2400,
-				4800,	9600,	19200,	38400 },
-			{ /* slowbaud & CBAUDEX */
-				0,	57600,	115200,	230400,
-				460800,	150,	200,	921600,
-				600,	1200,	1800,	2400,
-				4800,	9600,	19200,	38400 },
-			{ /* fastbaud */
-				0,	57600,	76800,	115200,
-				14400,	57600,	230400,	76800,
-				115200,	230400,	28800,	460800,
-				921600,	9600,	19200,	38400 },
-			{ /* fastbaud & CBAUDEX */
-				0,	57600,	115200,	230400,
-				460800,	150,	200,	921600,
-				600,	1200,	1800,	2400,
-				4800,	9600,	19200,	38400 }
-		};
-
-		/* Only use the TXPrint baud rate if the terminal unit is NOT open */
-		if (!(ch->ch_tun.un_flags & UN_ISOPEN) && (un->un_type == DGAP_PRINT))
-			baud = C_BAUD(ch->ch_pun.un_tty) & 0xff;
-		else
-			baud = C_BAUD(ch->ch_tun.un_tty) & 0xff;
-
-		if (ch->ch_c_cflag & CBAUDEX)
-			iindex = 1;
-
-		if (ch->ch_digi.digi_flags & DIGI_FAST)
-			iindex += 2;
-
-		jindex = baud;
-
-		if ((iindex >= 0) && (iindex < 4) && (jindex >= 0) && (jindex < 16)) {
-			baud = bauds[iindex][jindex];
-		} else {
-			DPR_IOCTL(("baud indices were out of range (%d)(%d)",
-				iindex, jindex));
-			baud = 0;
-		}
-
-		if (baud == 0)  
-			baud = 9600;
-
-		ch->ch_baud_info = baud;
-
-
-		/*
-		 * CBAUD has bit position 0x1000 set these days to indicate Linux
-		 * baud rate remap.
-		 * We use a different bit assignment for high speed.  Clear this
-		 * bit out while grabbing the parts of "cflag" we want.
-		 */
-		cflag = ch->ch_c_cflag & ((CBAUD ^ CBAUDEX) | PARODD | PARENB | CSTOPB | CSIZE);
-
-		/*
-		 * HUPCL bit is used by FEP to indicate fast baud
-		 * table is to be used.
-		 */
-		if ((ch->ch_digi.digi_flags & DIGI_FAST) || (ch->ch_c_cflag & CBAUDEX))
-			cflag |= HUPCL;
-
-
-		if ((ch->ch_c_cflag & CBAUDEX) && !(ch->ch_digi.digi_flags & DIGI_FAST)) {
-		/*
-		 * The below code is trying to guarantee that only baud rates
-		 * 115200, 230400, 460800, 921600 are remapped.  We use exclusive or
-		 * because the various baud rates share common bit positions
-		 * and therefore can't be tested for easily.
-		 */
-			tcflag_t tcflag = (ch->ch_c_cflag & CBAUD) | CBAUDEX;
-			int baudpart = 0;
-
-			/* Map high speed requests to index into FEP's baud table */
-			switch (tcflag) {
-			case B57600 :
-				baudpart = 1;
-				break;
-#ifdef B76800
-			case B76800 :
-				baudpart = 2;
-				break;
-#endif
-			case B115200 :
-				baudpart = 3;
-				break;
-			case B230400 :
-				baudpart = 9;
-				break;
-			case B460800 :
-				baudpart = 11;
-				break;
-#ifdef B921600
-			case B921600 :
-				baudpart = 12;
-				break;
-#endif
-			default:
-				baudpart = 0;
-			}
-
-			if (baudpart)
-				cflag = (cflag & ~(CBAUD | CBAUDEX)) | baudpart;
-		}
-
-		cflag &= 0xffff;
-
-		if (cflag != ch->ch_fepcflag) {
-			ch->ch_fepcflag = (u16) (cflag & 0xffff);
-
-			/* Okay to have channel and board locks held calling this */
-			dgap_cmdw(ch, SCFLAG, (u16) cflag, 0);
-		}
-
-		/* Handle transition from B0 */   
-		if (ch->ch_flags & CH_BAUD0) {
-			ch->ch_flags &= ~(CH_BAUD0);
-			ch->ch_mval |= (D_RTS(ch)|D_DTR(ch));
-		}
-		mval = D_DTR(ch) | D_RTS(ch);
-	}
-
-	/*
-	 * Get input flags.
-	 */
-	iflag = ch->ch_c_iflag & (IGNBRK | BRKINT | IGNPAR | PARMRK | INPCK | ISTRIP | IXON | IXANY | IXOFF);
-
-	if ((ch->ch_startc == _POSIX_VDISABLE) || (ch->ch_stopc == _POSIX_VDISABLE)) {
-		iflag &= ~(IXON | IXOFF);
-		ch->ch_c_iflag &= ~(IXON | IXOFF);
-	}
-
-	/*
-	 * Only the IBM Xr card can switch between
-	 * 232 and 422 modes on the fly
-	 */
-	if (bd->device == PCI_DEVICE_XR_IBM_DID) {
-		if (ch->ch_digi.digi_flags & DIGI_422)
-			dgap_cmdb(ch, SCOMMODE, MODE_422, 0, 0);
-		else
-			dgap_cmdb(ch, SCOMMODE, MODE_232, 0, 0);
-	}
-
-	if (ch->ch_digi.digi_flags & DIGI_ALTPIN)
-		iflag |= IALTPIN ;
-
-	if (iflag != ch->ch_fepiflag) {
-		ch->ch_fepiflag = iflag;
-
-		/* Okay to have channel and board locks held calling this */
-		dgap_cmdw(ch, SIFLAG, (u16) ch->ch_fepiflag, 0);
-	}
-
-	/*
-	 * Select hardware handshaking.
-	 */
-	hflow = 0;
-
-	if (ch->ch_c_cflag & CRTSCTS) {
-		hflow |= (D_RTS(ch) | D_CTS(ch));
-	}
-	if (ch->ch_digi.digi_flags & RTSPACE)
-		hflow |= D_RTS(ch);
-	if (ch->ch_digi.digi_flags & DTRPACE)
-		hflow |= D_DTR(ch);  
-	if (ch->ch_digi.digi_flags & CTSPACE)
-		hflow |= D_CTS(ch);
-	if (ch->ch_digi.digi_flags & DSRPACE)
-		hflow |= D_DSR(ch);
-	if (ch->ch_digi.digi_flags & DCDPACE)
-		hflow |= D_CD(ch);
-
-	if (hflow != ch->ch_hflow) {
-		ch->ch_hflow = hflow;
-
-		/* Okay to have channel and board locks held calling this */
-		dgap_cmdb(ch, SHFLOW, (uchar) hflow, 0xff, 0);
-        }
-
-
-	/*
-	 * Set RTS and/or DTR Toggle if needed, but only if product is FEP5+ based.
-	 */
-	if (bd->bd_flags & BD_FEP5PLUS) {
-		u16 hflow2 = 0;
-		if (ch->ch_digi.digi_flags & DIGI_RTS_TOGGLE) {
-			hflow2 |= (D_RTS(ch));
-		}
-		if (ch->ch_digi.digi_flags & DIGI_DTR_TOGGLE) {
-			hflow2 |= (D_DTR(ch));
-		}
-
-		dgap_cmdw_ext(ch, 0xff03, hflow2, 0);
-	}
-
-	/*
-	 * Set modem control lines.  
-	 */
-
-	mval ^= ch->ch_mforce & (mval ^ ch->ch_mval);
-
-	DPR_PARAM(("dgap_param: mval: %x ch_mforce: %x ch_mval: %x ch_mostat: %x\n",
-		mval, ch->ch_mforce, ch->ch_mval, ch->ch_mostat));
-
-	if (ch->ch_mostat ^ mval) {
-		ch->ch_mostat = mval;
-
-		/* Okay to have channel and board locks held calling this */
-		DPR_PARAM(("dgap_param: Sending SMODEM mval: %x\n", mval));
-		dgap_cmdb(ch, SMODEM, (uchar) mval, D_RTS(ch)|D_DTR(ch), 0);
-	}
-
-	/*
-	 * Read modem signals, and then call carrier function.             
-	 */
-	ch->ch_mistat = readb(&(bs->m_stat));
-	dgap_carrier(ch);
-
-	/*      
-	 * Set the start and stop characters.
-	 */
-	if (ch->ch_startc != ch->ch_fepstartc || ch->ch_stopc != ch->ch_fepstopc) {
-		ch->ch_fepstartc = ch->ch_startc;
-		ch->ch_fepstopc =  ch->ch_stopc;
-
-		/* Okay to have channel and board locks held calling this */
-		dgap_cmdb(ch, SFLOWC, ch->ch_fepstartc, ch->ch_fepstopc, 0);
-	}
-
-	/*
-	 * Set the Auxiliary start and stop characters.
-	 */     
-	if (ch->ch_astartc != ch->ch_fepastartc || ch->ch_astopc != ch->ch_fepastopc) {
-		ch->ch_fepastartc = ch->ch_astartc;
-		ch->ch_fepastopc = ch->ch_astopc;
-
-		/* Okay to have channel and board locks held calling this */
-		dgap_cmdb(ch, SAFLOWC, ch->ch_fepastartc, ch->ch_fepastopc, 0);
-	}
-
-	DPR_PARAM(("param finish\n"));
-
-	return 0;
-}
-
-/*
- * dgap_parity_scan()
- *
- * Convert the FEP5 way of reporting parity errors and breaks into
- * the Linux line discipline way.
- */
-void dgap_parity_scan(struct channel_t *ch, unsigned char *cbuf, unsigned char *fbuf, int *len)
-{
-	int l = *len;
-	int count = 0;
-	unsigned char *in, *cout, *fout;
-	unsigned char c;
-
-	in = cbuf;
-	cout = cbuf;
-	fout = fbuf;
-
-	DPR_PSCAN(("dgap_parity_scan start\n"));
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	while (l--) {
-		c = *in++;
-		switch (ch->pscan_state) {
-		default:
-			/* reset to sanity and fall through */
-			ch->pscan_state = 0;
-
-		case 0:
-			/* No FF seen yet */
-			if (c == (unsigned char) '\377') {
-				/* delete this character from stream */
-				ch->pscan_state = 1;
-			} else {
-				*cout++ = c;
-				*fout++ = TTY_NORMAL;
-				count += 1;
-			}
-			break;
-
-		case 1:
-			/* first FF seen */
-			if (c == (unsigned char) '\377') {
-				/* doubled ff, transform to single ff */
-				*cout++ = c;
-				*fout++ = TTY_NORMAL;
-				count += 1;
-				ch->pscan_state = 0;
-			} else {
-				/* save value examination in next state */
-				ch->pscan_savechar = c;
-				ch->pscan_state = 2; 
-			}
-			break;
-
-		case 2:
-			/* third character of ff sequence */
-
-			*cout++ = c;
-
-			if (ch->pscan_savechar == 0x0) {
-
-				if (c == 0x0) {
-					DPR_PSCAN(("dgap_parity_scan in 3rd char of ff seq. c: %x setting break.\n", c));
-					ch->ch_err_break++;
-					*fout++ = TTY_BREAK;
-				}
-				else {
-					DPR_PSCAN(("dgap_parity_scan in 3rd char of ff seq. c: %x setting parity.\n", c));
-					ch->ch_err_parity++;
-					*fout++ = TTY_PARITY;
-				}
-			}
-			else {
-				DPR_PSCAN(("%s:%d Logic Error.\n", __FILE__, __LINE__));
-			}
-
-			count += 1;
-			ch->pscan_state = 0;
-		}       
-	}
-	*len = count;
-	DPR_PSCAN(("dgap_parity_scan finish\n"));
-}
-
-/*=======================================================================
- *
- *      dgap_event - FEP to host event processing routine.
- *
- *              bd     - Board of current event.
- *
- *=======================================================================*/
-static int dgap_event(struct board_t *bd)
-{
-	struct channel_t *ch;
-	ulong		lock_flags;
-	ulong		lock_flags2;
-	struct bs_t	*bs;
-	uchar		*event;
-	uchar		*vaddr = NULL;
-	struct ev_t	*eaddr = NULL;
-	uint		head;
-	uint		tail;
-	int		port;
-	int		reason;
-	int		modem;
-	int		b1;
-
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return -ENXIO;
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-
-	vaddr = bd->re_map_membase;
-
-	if (!vaddr) {
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return -ENXIO;
-	}
-
-	eaddr = (struct ev_t *) (vaddr + EVBUF);
-
-	/* Get our head and tail */
-	head = readw(&(eaddr->ev_head));
-	tail = readw(&(eaddr->ev_tail));
-
-	/*
-	 * Forget it if pointers out of range.
-	 */
-
-	if (head >= EVMAX - EVSTART || tail >= EVMAX - EVSTART ||
-	    (head | tail) & 03) {
-		DPR_EVENT(("should be calling xxfail %d\n", __LINE__));
-		/* Let go of board lock */
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return -ENXIO;
-	}
-
-	/*
-	 * Loop to process all the events in the buffer.
-	 */
-	while (tail != head) {
-
-		/*
-		 * Get interrupt information.
-		 */
-
-		event = bd->re_map_membase + tail + EVSTART;
-
-		port   = event[0];
-		reason = event[1];
-		modem  = event[2];
-		b1     = event[3];
-
-		DPR_EVENT(("event: jiffies: %ld port: %d reason: %x modem: %x\n",
-			jiffies, port, reason, modem));
-
-		/*
-		 * Make sure the interrupt is valid.
-		 */
-                if (port >= bd->nasync) 
-			goto next;
-
-		if (!(reason & (IFMODEM | IFBREAK | IFTLW | IFTEM | IFDATA))) 
-			goto next;
-
-		ch = bd->channels[port];
-
-		if (!ch || ch->magic != DGAP_CHANNEL_MAGIC) 
-			goto next;
-
-		/*
-		 * If we have made it here, the event was valid.
-		 * Lock down the channel.
-		 */
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-		bs = ch->ch_bs;
-
-		if (!bs) {
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			goto next;
-		}
-
-		/*
-		 * Process received data.
-		 */
-		if (reason & IFDATA) {
-
-			/*
-			 * ALL LOCKS *MUST* BE DROPPED BEFORE CALLING INPUT!
-			 * input could send some data to ld, which in turn
-			 * could do a callback to one of our other functions.
-			 */
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-			dgap_input(ch);
-
-			DGAP_LOCK(bd->bd_lock, lock_flags);
-			DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-			if (ch->ch_flags & CH_RACTIVE)
-				ch->ch_flags |= CH_RENABLE;
-			else
-				writeb(1, &(bs->idata));
-
-			if (ch->ch_flags & CH_RWAIT) {
-				ch->ch_flags &= ~CH_RWAIT;
-
-				wake_up_interruptible(&ch->ch_tun.un_flags_wait);
-			}
-		}
-
-		/*
-		 * Process Modem change signals. 
-		 */
-		if (reason & IFMODEM) {
-			ch->ch_mistat = modem;
-			dgap_carrier(ch);
-		}
-
-		/*
-		 * Process break.
-		 */
-		if (reason & IFBREAK) {
-
-			DPR_EVENT(("got IFBREAK\n"));
-
-			if (ch->ch_tun.un_tty) {
-				/* A break has been indicated */
-				ch->ch_err_break++;
-				tty_buffer_request_room(ch->ch_tun.un_tty->port, 1);
-				tty_insert_flip_char(ch->ch_tun.un_tty->port, 0, TTY_BREAK);
-				tty_flip_buffer_push(ch->ch_tun.un_tty->port);
-			}
-		}
-
-		/*
-		 * Process Transmit low.
-		 */
-		if (reason & IFTLW) {
-
-			DPR_EVENT(("event: got low event\n"));
-
-			if (ch->ch_tun.un_flags & UN_LOW) {
-				ch->ch_tun.un_flags &= ~UN_LOW;
-
-				if (ch->ch_tun.un_flags & UN_ISOPEN) {
-					if ((ch->ch_tun.un_tty->flags & 
-					   (1 << TTY_DO_WRITE_WAKEUP)) &&
-						ch->ch_tun.un_tty->ldisc->ops->write_wakeup)
-					{
-						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-						DGAP_UNLOCK(bd->bd_lock, lock_flags);
-						(ch->ch_tun.un_tty->ldisc->ops->write_wakeup)(ch->ch_tun.un_tty);
-						DGAP_LOCK(bd->bd_lock, lock_flags);
-						DGAP_LOCK(ch->ch_lock, lock_flags2);
-					}
-					wake_up_interruptible(&ch->ch_tun.un_tty->write_wait);
-					wake_up_interruptible(&ch->ch_tun.un_flags_wait);
-
-					DPR_EVENT(("event: Got low event. jiffies: %lu\n", jiffies));
-				}
-			}
-
-			if (ch->ch_pun.un_flags & UN_LOW) {
-				ch->ch_pun.un_flags &= ~UN_LOW;
-				if (ch->ch_pun.un_flags & UN_ISOPEN) {
-					if ((ch->ch_pun.un_tty->flags & 
-					   (1 << TTY_DO_WRITE_WAKEUP)) &&
-						ch->ch_pun.un_tty->ldisc->ops->write_wakeup)
-					{
-						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-						DGAP_UNLOCK(bd->bd_lock, lock_flags);
-						(ch->ch_pun.un_tty->ldisc->ops->write_wakeup)(ch->ch_pun.un_tty);
-						DGAP_LOCK(bd->bd_lock, lock_flags);
-						DGAP_LOCK(ch->ch_lock, lock_flags2);
-					}
-					wake_up_interruptible(&ch->ch_pun.un_tty->write_wait);
-					wake_up_interruptible(&ch->ch_pun.un_flags_wait);
-				}
-			}
-
-			if (ch->ch_flags & CH_WLOW) {
-				ch->ch_flags &= ~CH_WLOW;
-				wake_up_interruptible(&ch->ch_flags_wait);
-			}
-		}
-
-		/*
-		 * Process Transmit empty.
-		 */
-		if (reason & IFTEM) {
-			DPR_EVENT(("event: got empty event\n"));
-
-			if (ch->ch_tun.un_flags & UN_EMPTY) {
-				ch->ch_tun.un_flags &= ~UN_EMPTY;
-				if (ch->ch_tun.un_flags & UN_ISOPEN) {
-					if ((ch->ch_tun.un_tty->flags & 
-					   (1 << TTY_DO_WRITE_WAKEUP)) &&
-						ch->ch_tun.un_tty->ldisc->ops->write_wakeup)
-					{
-						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-						DGAP_UNLOCK(bd->bd_lock, lock_flags);
-						(ch->ch_tun.un_tty->ldisc->ops->write_wakeup)(ch->ch_tun.un_tty);
-						DGAP_LOCK(bd->bd_lock, lock_flags);
-						DGAP_LOCK(ch->ch_lock, lock_flags2);
-					}
-					wake_up_interruptible(&ch->ch_tun.un_tty->write_wait);
-					wake_up_interruptible(&ch->ch_tun.un_flags_wait);
-				}
-			}
-
-			if (ch->ch_pun.un_flags & UN_EMPTY) {
-				ch->ch_pun.un_flags &= ~UN_EMPTY;
-				if (ch->ch_pun.un_flags & UN_ISOPEN) {
-					if ((ch->ch_pun.un_tty->flags & 
-					   (1 << TTY_DO_WRITE_WAKEUP)) &&
-						ch->ch_pun.un_tty->ldisc->ops->write_wakeup)
-					{
-						DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-						DGAP_UNLOCK(bd->bd_lock, lock_flags);
-						(ch->ch_pun.un_tty->ldisc->ops->write_wakeup)(ch->ch_pun.un_tty);
-						DGAP_LOCK(bd->bd_lock, lock_flags);
-						DGAP_LOCK(ch->ch_lock, lock_flags2);
-					}
-					wake_up_interruptible(&ch->ch_pun.un_tty->write_wait);
-					wake_up_interruptible(&ch->ch_pun.un_flags_wait);
-				}
-			}
-
-
-			if (ch->ch_flags & CH_WEMPTY) {
-				ch->ch_flags &= ~CH_WEMPTY;
-				wake_up_interruptible(&ch->ch_flags_wait);
-			}
-		}
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-
-next:
-		tail = (tail + 4) & (EVMAX - EVSTART - 4);
-	}
-
-	writew(tail, &(eaddr->ev_tail));
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	return 0;
-}               
-
-/*
- * Parse a configuration file read into memory as a string.
- */
-int	dgap_parsefile(char **in, int Remove)
-{
-	struct cnode *p, *brd, *line, *conc;
-	int	rc;
-	char	*s = NULL, *s2 = NULL;
-	int	linecnt = 0;
-
-	p = &dgap_head;
-	brd = line = conc = NULL;
-
-	/* perhaps we are adding to an existing list? */
-	while (p->next != NULL) {
-		p = p->next;
-	}
-
-	/* file must start with a BEGIN */
-	while ( (rc = dgap_gettok(in,p)) != BEGIN ) {
-		if (rc == 0) {
-			dgap_err("unexpected EOF");
-			return(-1);
-		}
-	}
-
-	for (; ; ) {
-		rc = dgap_gettok(in,p);
-		if (rc == 0) {
-			dgap_err("unexpected EOF");
-			return(-1);
-		}
-
-		switch (rc) {
-		case 0:
-			dgap_err("unexpected end of file");
-			return(-1);
-
-		case BEGIN:	/* should only be 1 begin */
-			dgap_err("unexpected config_begin\n");
-			return(-1);
-
-		case END:
-			return(0);
-
-		case BOARD:	/* board info */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(BNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-
-			p->u.board.status = dgap_savestring("No");
-			line = conc = NULL;
-			brd = p;
-			linecnt = -1;
-			break;
-
-		case APORT2_920P:	/* AccelePort_4 */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_2r_920 string");
-				return(-1);
-			}
-			p->u.board.type = APORT2_920P;
-			p->u.board.v_type = 1;
-			DPR_INIT(("Adding Digi_2r_920 PCI to config...\n"));
-			break;
-
-		case APORT4_920P:	/* AccelePort_4 */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_4r_920 string");
-				return(-1);
-			}
-			p->u.board.type = APORT4_920P;
-			p->u.board.v_type = 1;
-			DPR_INIT(("Adding Digi_4r_920 PCI to config...\n"));
-			break;
-
-		case APORT8_920P:	/* AccelePort_8 */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_8r_920 string");
-				return(-1);
-			}
-			p->u.board.type = APORT8_920P;
-			p->u.board.v_type = 1;
-			DPR_INIT(("Adding Digi_8r_920 PCI to config...\n"));
-			break;
-
-		case PAPORT4:	/* AccelePort_4 PCI */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_4r(PCI) string");
-				return(-1);
-			}
-			p->u.board.type = PAPORT4;
-			p->u.board.v_type = 1;
-			DPR_INIT(("Adding Digi_4r PCI to config...\n"));
-			break;
-
-		case PAPORT8:	/* AccelePort_8 PCI */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_8r string");
-				return(-1);
-			}
-			p->u.board.type = PAPORT8;
-			p->u.board.v_type = 1;
-			DPR_INIT(("Adding Digi_8r PCI to config...\n"));
-			break;
-
-		case PCX:	/* PCI C/X */
-			if (p->type != BNODE) {
-				dgap_err("unexpected Digi_C/X_(PCI) string");
-				return(-1);
-			}
-			p->u.board.type = PCX;
-			p->u.board.v_type = 1;
-			p->u.board.conc1 = 0;
-			p->u.board.conc2 = 0;
-			p->u.board.module1 = 0;
-			p->u.board.module2 = 0;
-			DPR_INIT(("Adding PCI C/X to config...\n"));
-			break;
-
-		case PEPC:	/* PCI EPC/X */
-			if (p->type != BNODE) {
-				dgap_err("unexpected \"Digi_EPC/X_(PCI)\" string");
-				return(-1);
-			}
-			p->u.board.type = PEPC;
-			p->u.board.v_type = 1;
-			p->u.board.conc1 = 0;
-			p->u.board.conc2 = 0;
-			p->u.board.module1 = 0;
-			p->u.board.module2 = 0;
-			DPR_INIT(("Adding PCI EPC/X to config...\n"));
-			break;
-
-		case PPCM:	/* PCI/Xem */
-			if (p->type != BNODE) {
-				dgap_err("unexpected PCI/Xem string");
-				return(-1);
-			}
-			p->u.board.type = PPCM;
-			p->u.board.v_type = 1;
-			p->u.board.conc1 = 0;
-			p->u.board.conc2 = 0;
-			DPR_INIT(("Adding PCI XEM to config...\n"));
-			break;
-
-		case IO:	/* i/o port */
-			if (p->type != BNODE) {
-				dgap_err("IO port only vaild for boards");
-				return(-1);
-			}
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.portstr = dgap_savestring(s);
-			p->u.board.port = (short)simple_strtol(s, &s2, 0);
-			if ((short)strlen(s) > (short)(s2 - s)) {
-				dgap_err("bad number for IO port");
-				return(-1);
-			}
-			p->u.board.v_port = 1;
-			DPR_INIT(("Adding IO (%s) to config...\n", s));
-			break;
-
-		case MEM:	/* memory address */
-			if (p->type != BNODE) {
-				dgap_err("memory address only vaild for boards");
-				return(-1);
-			}
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.addrstr = dgap_savestring(s);
-			p->u.board.addr = simple_strtoul(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for memory address");
-				return(-1);
-			}
-			p->u.board.v_addr = 1;
-			DPR_INIT(("Adding MEM (%s) to config...\n", s));
-			break;
-
-		case PCIINFO:	/* pci information */
-			if (p->type != BNODE) {
-				dgap_err("memory address only vaild for boards");
-				return(-1);
-			}
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.pcibusstr = dgap_savestring(s);
-			p->u.board.pcibus = simple_strtoul(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for pci bus");
-				return(-1);
-			}
-			p->u.board.v_pcibus = 1;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.pcislotstr = dgap_savestring(s);
-			p->u.board.pcislot = simple_strtoul(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for pci slot");
-				return(-1);
-			}
-			p->u.board.v_pcislot = 1;
-
-			DPR_INIT(("Adding PCIINFO (%s %s) to config...\n", p->u.board.pcibusstr, 
-				p->u.board.pcislotstr));
-			break;
-
-		case METHOD:
-			if (p->type != BNODE) {
-				dgap_err("install method only vaild for boards");
-				return(-1);
-			}
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.method = dgap_savestring(s);
-			p->u.board.v_method = 1;
-			DPR_INIT(("Adding METHOD (%s) to config...\n", s));
-			break;
-
-		case STATUS:
-			if (p->type != BNODE) {
-				dgap_err("config status only vaild for boards");
-				return(-1);
-			}
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.board.status = dgap_savestring(s);
-			DPR_INIT(("Adding STATUS (%s) to config...\n", s));
-			break;
-
-		case NPORTS:	/* number of ports */
-			if (p->type == BNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.board.nport = (char)simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for number of ports");
-					return(-1);
-				}
-				p->u.board.v_nport = 1;
-			} else if (p->type == CNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.conc.nport = (char)simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for number of ports");
-					return(-1);
-				}
-				p->u.conc.v_nport = 1;
-			} else if (p->type == MNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.module.nport = (char)simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for number of ports");
-					return(-1);
-				}
-				p->u.module.v_nport = 1;
-			} else {
-				dgap_err("nports only valid for concentrators or modules");
-				return(-1);
-			}
-			DPR_INIT(("Adding NPORTS (%s) to config...\n", s));
-			break;
-
-		case ID:	/* letter ID used in tty name */
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-
-			p->u.board.status = dgap_savestring(s);
-
-			if (p->type == CNODE) {
-				p->u.conc.id = dgap_savestring(s);
-				p->u.conc.v_id = 1;
-			} else if (p->type == MNODE) {
-				p->u.module.id = dgap_savestring(s);
-				p->u.module.v_id = 1;
-			} else {
-				dgap_err("id only valid for concentrators or modules");
-				return(-1);
-			}
-			DPR_INIT(("Adding ID (%s) to config...\n", s));
-			break;
-
-		case STARTO:	/* start offset of ID */
-			if (p->type == BNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.board.start = simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for start of tty count");
-					return(-1);
-				}
-				p->u.board.v_start = 1;
-			} else if (p->type == CNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.conc.start = simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for start of tty count");
-					return(-1);
-				}
-				p->u.conc.v_start = 1;
-			} else if (p->type == MNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.module.start = simple_strtol(s, &s2, 0);
-				if ((int)strlen(s) > (int)(s2 - s)) {
-					dgap_err("bad number for start of tty count");
-					return(-1);
-				}
-				p->u.module.v_start = 1;
-			} else {
-				dgap_err("start only valid for concentrators or modules");
-				return(-1);
-			}
-			DPR_INIT(("Adding START (%s) to config...\n", s));
-			break;
-
-		case TTYN:	/* tty name prefix */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(TNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			if ( (s = dgap_getword(in)) == NULL ) {
-				dgap_err("unexpeced end of file");
-				return(-1);
-			}
-			if ( (p->u.ttyname = dgap_savestring(s)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			DPR_INIT(("Adding TTY (%s) to config...\n", s));
-			break;
-
-		case CU:	/* cu name prefix */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(CUNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			if ( (s = dgap_getword(in)) == NULL ) {
-				dgap_err("unexpeced end of file");
-				return(-1);
-			}
-			if ( (p->u.cuname = dgap_savestring(s)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			DPR_INIT(("Adding CU (%s) to config...\n", s));
-			break;
-
-		case LINE:	/* line information */
-			if (dgap_checknode(p))
-				return(-1);
-			if (brd == NULL) {
-				dgap_err("must specify board before line info");
-				return(-1);
-			}
-			switch (brd->u.board.type) {
-			case PPCM:
-				dgap_err("line not vaild for PC/em");
-				return(-1);
-			}
-			if ( (p->next = dgap_newnode(LNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			conc = NULL;
-			line = p;
-			linecnt++;
-			DPR_INIT(("Adding LINE to config...\n"));
-			break;
-
-		case CONC:	/* concentrator information */
-			if (dgap_checknode(p))
-				return(-1);
-			if (line == NULL) {
-				dgap_err("must specify line info before concentrator");
-				return(-1);
-			}
-			if ( (p->next = dgap_newnode(CNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			conc = p;
-			if (linecnt)
-				brd->u.board.conc2++;
-			else
-				brd->u.board.conc1++;
-
-			DPR_INIT(("Adding CONC to config...\n"));
-			break;
-
-		case CX:	/* c/x type concentrator */
-			if (p->type != CNODE) {
-				dgap_err("cx only valid for concentrators");
-				return(-1);
-			}
-			p->u.conc.type = CX;
-			p->u.conc.v_type = 1;
-			DPR_INIT(("Adding CX to config...\n"));
-			break;
-
-		case EPC:	/* epc type concentrator */
-			if (p->type != CNODE) {
-				dgap_err("cx only valid for concentrators");
-				return(-1);
-			}
-			p->u.conc.type = EPC;
-			p->u.conc.v_type = 1;
-			DPR_INIT(("Adding EPC to config...\n"));
-			break;
-
-		case MOD:	/* EBI module */
-			if (dgap_checknode(p))
-				return(-1);
-			if (brd == NULL) {
-				dgap_err("must specify board info before EBI modules");
-				return(-1);
-			}
-			switch (brd->u.board.type) {
-			case PPCM:
-				linecnt = 0;
-				break;
-			default:
-				if (conc == NULL) {
-					dgap_err("must specify concentrator info before EBI module");
-					return(-1);
-				}
-			}
-			if ( (p->next = dgap_newnode(MNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			if (linecnt)
-				brd->u.board.module2++;
-			else
-				brd->u.board.module1++;
-
-			DPR_INIT(("Adding MOD to config...\n"));
-			break;
-
-		case PORTS:	/* ports type EBI module */
-			if (p->type != MNODE) {
-				dgap_err("ports only valid for EBI modules");
-				return(-1);
-			}
-			p->u.module.type = PORTS;
-			p->u.module.v_type = 1;
-			DPR_INIT(("Adding PORTS to config...\n"));
-			break;
-
-		case MODEM:	/* ports type EBI module */
-			if (p->type != MNODE) {
-				dgap_err("modem only valid for modem modules");
-				return(-1);
-			}
-			p->u.module.type = MODEM;
-			p->u.module.v_type = 1;
-			DPR_INIT(("Adding MODEM to config...\n"));
-			break;
-
-		case CABLE:
-			if (p->type == LNODE) {
-				if ((s = dgap_getword(in)) == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.line.cable = dgap_savestring(s);
-				p->u.line.v_cable = 1;
-			}
-			DPR_INIT(("Adding CABLE (%s) to config...\n", s));
-			break;
-
-		case SPEED:	/* sync line speed indication */
-			if (p->type == LNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.line.speed = (char)simple_strtol(s, &s2, 0);
-				if ((short)strlen(s) > (short)(s2 - s)) {
-					dgap_err("bad number for line speed");
-					return(-1);
-				}
-				p->u.line.v_speed = 1;
-			} else if (p->type == CNODE) {
-				s = dgap_getword(in);
-				if (s == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.conc.speed = (char)simple_strtol(s, &s2, 0);
-				if ((short)strlen(s) > (short)(s2 - s)) {
-					dgap_err("bad number for line speed");
-					return(-1);
-				}
-				p->u.conc.v_speed = 1;
-			} else {
-				dgap_err("speed valid only for lines or concentrators.");
-				return(-1);
-			}
-			DPR_INIT(("Adding SPEED (%s) to config...\n", s));
-			break;
-
-		case CONNECT:
-			if (p->type == CNODE) {
-				if ((s = dgap_getword(in)) == NULL) {
-					dgap_err("unexpected end of file");
-					return(-1);
-				}
-				p->u.conc.connect = dgap_savestring(s);
-				p->u.conc.v_connect = 1;
-			}
-			DPR_INIT(("Adding CONNECT (%s) to config...\n", s));
-			break;
-		case PRINT:	/* transparent print name prefix */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(PNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			if ( (s = dgap_getword(in)) == NULL ) {
-				dgap_err("unexpeced end of file");
-				return(-1);
-			}
-			if ( (p->u.printname = dgap_savestring(s)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			DPR_INIT(("Adding PRINT (%s) to config...\n", s));
-			break;
-
-		case CMAJOR:	/* major number */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(JNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.majornumber = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for major number");
-				return(-1);
-			}
-			DPR_INIT(("Adding CMAJOR (%s) to config...\n", s));
-			break;
-
-		case ALTPIN:	/* altpin setting */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(ANODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.altpin = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for altpin");
-				return(-1);
-			}
-			DPR_INIT(("Adding ALTPIN (%s) to config...\n", s));
-			break;
-
-		case USEINTR:		/* enable interrupt setting */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(INTRNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.useintr = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for useintr");
-				return(-1);
-			}
-			DPR_INIT(("Adding USEINTR (%s) to config...\n", s));
-			break;
-
-		case TTSIZ:	/* size of tty structure */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(TSNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.ttysize = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for ttysize");
-				return(-1);
-			}
-			DPR_INIT(("Adding TTSIZ (%s) to config...\n", s));
-			break;
-
-		case CHSIZ:	/* channel structure size */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(CSNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.chsize = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for chsize");
-				return(-1);
-			}
-			DPR_INIT(("Adding CHSIZE (%s) to config...\n", s));
-			break;
-
-		case BSSIZ:	/* board structure size */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(BSNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.bssize = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for bssize");
-				return(-1);
-			}
-			DPR_INIT(("Adding BSSIZ (%s) to config...\n", s));
-			break;
-
-		case UNTSIZ:	/* sched structure size */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(USNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.unsize = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for schedsize");
-				return(-1);
-			}
-			DPR_INIT(("Adding UNTSIZ (%s) to config...\n", s));
-			break;
-
-		case F2SIZ:	/* f2200 structure size */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(FSNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.f2size = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for f2200size");
-				return(-1);
-			}
-			DPR_INIT(("Adding F2SIZ (%s) to config...\n", s));
-			break;
-
-		case VPSIZ:	/* vpix structure size */
-			if (dgap_checknode(p))
-				return(-1);
-			if ( (p->next = dgap_newnode(VSNODE)) == NULL ) {
-				dgap_err("out of memory");
-				return(-1);
-			}
-			p = p->next;
-			s = dgap_getword(in);
-			if (s == NULL) {
-				dgap_err("unexpected end of file");
-				return(-1);
-			}
-			p->u.vpixsize = simple_strtol(s, &s2, 0);
-			if ((int)strlen(s) > (int)(s2 - s)) {
-				dgap_err("bad number for vpixsize");
-				return(-1);
-			}
-			DPR_INIT(("Adding VPSIZ (%s) to config...\n", s));
-			break;
-		}
-	}
-}
-
-
-/*
- * dgap_sindex: much like index(), but it looks for a match of any character in
- * the group, and returns that position.  If the first character is a ^, then
- * this will match the first occurrence not in that group.
- */
-static char *dgap_sindex (char *string, char *group)
-{
-	char    *ptr;
-
-	if (!string || !group)
-		return (char *) NULL;
-
-	if (*group == '^') {   
-		group++;
-		for (; *string; string++) {
-			for (ptr = group; *ptr; ptr++) {
-				if (*ptr == *string)
-					break;
-			}
-			if (*ptr == '\0')
-				return string;
-		}
-	}   
-	else {
-		for (; *string; string++) {
-			for (ptr = group; *ptr; ptr++) {
-				if (*ptr == *string)
-					return string;
-			}
-		}
-	}
-
-	return (char *) NULL;
-}
-
-
-/*
- * Get a token from the input file; return 0 if end of file is reached
- */
-static int dgap_gettok(char **in, struct cnode *p)
-{
-	char	*w;
-	struct toklist *t;
-	
-	if (strstr(dgap_cword, "boar")) {
-		w = dgap_getword(in);
-		snprintf(dgap_cword, MAXCWORD, "%s", w);
-		for (t = dgap_tlist; t->token != 0; t++) {
-			if ( !strcmp(w, t->string)) {
-				return(t->token);
-			} 
-		}
-		dgap_err("board !!type not specified");
-		return(1);
-	}
-	else {
-		while ( (w = dgap_getword(in)) != NULL ) {
-			snprintf(dgap_cword, MAXCWORD, "%s", w);
-			for (t = dgap_tlist; t->token != 0; t++) {
-				if ( !strcmp(w, t->string) )
-					return(t->token);
-			}
-		}
-		return(0);
-	}
-}
-
-
-/*
- * get a word from the input stream, also keep track of current line number.
- * words are separated by whitespace.
- */
-static char *dgap_getword(char **in)
-{
-	char *ret_ptr = *in;
-
-        char *ptr = dgap_sindex(*in, " \t\n");
-
-	/* If no word found, return null */
-	if (!ptr)
-		return NULL;
-
-	/* Mark new location for our buffer */
-	*ptr = '\0';
-	*in = ptr + 1;
-
-	/* Eat any extra spaces/tabs/newlines that might be present */
-	while (*in && **in && ((**in == ' ') || (**in == '\t') || (**in == '\n'))) {
-		**in = '\0';
-		*in = *in + 1;
-	}
-
-	return ret_ptr;
-}
-
-
-/*
- * print an error message, giving the line number in the file where
- * the error occurred.
- */
-static void dgap_err(char *s)
-{
-	printk("DGAP: parse: %s\n", s);
-}
-
-
-/*
- * allocate a new configuration node of type t
- */
-static struct cnode *dgap_newnode(int t)
-{
-	struct cnode *n;
-
-	n = kmalloc(sizeof(struct cnode), GFP_ATOMIC);
-	if (n != NULL) {
-		memset((char *)n, 0, sizeof(struct cnode));
-		n->type = t;
-	}
-	return(n);
-}
-
-
-/*
- * dgap_checknode: see if all the necessary info has been supplied for a node
- * before creating the next node.
- */
-static int dgap_checknode(struct cnode *p)
-{
-	switch (p->type) {
-	case BNODE:
-		if (p->u.board.v_type == 0) {
-			dgap_err("board type !not specified");
-			return(1);
-		}
-
-		return(0);
-
-	case LNODE:
-		if (p->u.line.v_speed == 0) {
-			dgap_err("line speed not specified");
-			return(1);
-		}
-		return(0);
-
-	case CNODE:
-		if (p->u.conc.v_type == 0) {
-			dgap_err("concentrator type not specified");
-			return(1);
-		}
-		if (p->u.conc.v_speed == 0) {
-			dgap_err("concentrator line speed not specified");
-			return(1);
-		}
-		if (p->u.conc.v_nport == 0) {
-			dgap_err("number of ports on concentrator not specified");
-			return(1);
-		}
-		if (p->u.conc.v_id == 0) {
-			dgap_err("concentrator id letter not specified");
-			return(1);
-		}
-		return(0);
-
-	case MNODE:
-		if (p->u.module.v_type == 0) {
-			dgap_err("EBI module type not specified");
-			return(1);
-		}
-		if (p->u.module.v_nport == 0) {
-			dgap_err("number of ports on EBI module not specified");
-			return(1);
-		}
-		if (p->u.module.v_id == 0) {
-			dgap_err("EBI module id letter not specified");
-			return(1);
-		}
-		return(0);
-	}
-	return(0);
-}
-
-/*
- * save a string somewhere
- */
-static char	*dgap_savestring(char *s)
-{
-	char	*p;
-	if ( (p = kmalloc(strlen(s) + 1, GFP_ATOMIC) ) != NULL) {
-		strcpy(p, s);
-	}
-	return(p);
-}
-
-
-/*
- * Given a board pointer, returns whether we should use interrupts or not.
- */
-uint dgap_config_get_useintr(struct board_t *bd)
-{
-	struct cnode *p = NULL;
-
-	if (!bd)
-		return(0);
-
-	for (p = bd->bd_config; p; p = p->next) {
-		switch (p->type) {
-		case INTRNODE:
-			/*
-			 * check for pcxr types.
-			 */
-			return p->u.useintr;
-		default:
-			break;
-		}
-	}
-
-	/* If not found, then don't turn on interrupts. */
-	return 0;
-}
-
-
-/*
- * Given a board pointer, returns whether we turn on altpin or not.
- */
-uint dgap_config_get_altpin(struct board_t *bd)
-{
-	struct cnode *p = NULL;
-
-	if (!bd)
-		return(0);
-
-	for (p = bd->bd_config; p; p = p->next) {
-		switch (p->type) {
-		case ANODE:
-			/*
-			 * check for pcxr types.
-			 */
-			return p->u.altpin;
-		default:
-			break;
-		}
-	}
-
-	/* If not found, then don't turn on interrupts. */
-	return 0;
-}
-
-
-
-/*
- * Given a specific type of board, if found, detached link and 
- * returns the first occurrence in the list.
- */
-struct cnode *dgap_find_config(int type, int bus, int slot)
-{
-	struct cnode *p, *prev = NULL, *prev2 = NULL, *found = NULL;
-
-	p = &dgap_head;
-
-	while (p->next != NULL) {
-		prev = p;
-		p = p->next;
-
-		if (p->type == BNODE) {
-
-			if (p->u.board.type == type) {
-
-				if (p->u.board.v_pcibus && p->u.board.pcibus != bus) {
-					DPR(("Found matching board, but wrong bus position. System says bus %d, we want bus %ld\n",
-						bus, p->u.board.pcibus));
-					continue;
-				}
-				if (p->u.board.v_pcislot && p->u.board.pcislot != slot) {
-					DPR_INIT(("Found matching board, but wrong slot position. System says slot %d, we want slot %ld\n",
-						slot, p->u.board.pcislot));
-					continue;
-				}
-
-				DPR_INIT(("Matched type in config file\n"));
-
-				found = p;
-				/*
-				 * Keep walking thru the list till we find the next board.
-				 */
-				while (p->next != NULL) {
-					prev2 = p;
-					p = p->next;
-					if (p->type == BNODE) {
-
-						/*
-						 * Mark the end of our 1 board chain of configs.
-						 */
-						prev2->next = NULL;
-
-						/*
-						 * Link the "next" board to the previous board,
-						 * effectively "unlinking" our board from the main config.
-						 */
-						prev->next = p;
-
-						return found;
-					}
-				}
-				/*
-				 * It must be the last board in the list.
-				 */
-				prev->next = NULL;
-				return found;
-			}
-		}
-	}
-	return NULL;
-}
-
-/*
- * Given a board pointer, walks the config link, counting up
- * all ports user specified should be on the board.
- * (This does NOT mean they are all actually present right now tho)
- */
-uint dgap_config_get_number_of_ports(struct board_t *bd)
-{
-	int count = 0;
-	struct cnode *p = NULL;
-
-	if (!bd)
-		return(0);
-
-	for (p = bd->bd_config; p; p = p->next) {
-
-		switch (p->type) {
-		case BNODE:
-			/*
-			 * check for pcxr types.
-			 */
-			if (p->u.board.type > EPCFE)
-				count += p->u.board.nport;
-			break;
-		case CNODE:
-			count += p->u.conc.nport;
-			break;
-		case MNODE:
-			count += p->u.module.nport;
-			break;
-		}
-	}
-	return (count);
-}
-
-char *dgap_create_config_string(struct board_t *bd, char *string)
-{
-	char *ptr = string;
-	struct cnode *p = NULL;
-	struct cnode *q = NULL;
-	int speed;
-
-	if (!bd) {
-		*ptr = 0xff;
-		return string;
-	}
-
-	for (p = bd->bd_config; p; p = p->next) {
-
-		switch (p->type) {
-		case LNODE:
-			*ptr = '\0';
-			ptr++;
-			*ptr = p->u.line.speed;
-			ptr++;
-			break;
-		case CNODE:
-			/*
-			 * Because the EPC/con concentrators can have EM modules
-			 * hanging off of them, we have to walk ahead in the list
-			 * and keep adding the number of ports on each EM to the config.
-			 * UGH!
-			 */
-			speed = p->u.conc.speed;
-			q = p->next;
-			if ((q != NULL) && (q->type == MNODE) ) {
-				*ptr = (p->u.conc.nport + 0x80);
-				ptr++;
-				p = q;
-				while ((q->next != NULL) && (q->next->type) == MNODE) {
-					*ptr = (q->u.module.nport + 0x80);
-					ptr++;
-					p = q;
-					q = q->next;
-				}
-				*ptr = q->u.module.nport;
-				ptr++;
-			} else {
-				*ptr = p->u.conc.nport;
-				ptr++;
-			}
-
-			*ptr = speed;
-			ptr++;
-			break;
-		}
-	}
-
-	*ptr = 0xff;
-	return string;
-}
-
-
-
-char *dgap_get_config_letters(struct board_t *bd, char *string)
-{
-	int found = FALSE;
-	char *ptr = string;
-	struct cnode *cptr = NULL;
-	int len = 0;
-	int left = MAXTTYNAMELEN;
-
-	if (!bd) {
-		return "<NULL>";
-	}
-
-	for (cptr = bd->bd_config; cptr; cptr = cptr->next) {
-
-		if ((cptr->type == BNODE) &&
-		     ((cptr->u.board.type == APORT2_920P) || (cptr->u.board.type == APORT4_920P) ||
-		     (cptr->u.board.type == APORT8_920P) || (cptr->u.board.type == PAPORT4) ||
-		     (cptr->u.board.type == PAPORT8))) {
-
-			found = TRUE;
-		}
-
-		if (cptr->type == TNODE && found == TRUE) {
-			char *ptr1;
-			if (strstr(cptr->u.ttyname, "tty")) {
-				ptr1 = cptr->u.ttyname;
-				ptr1 += 3;
-			}
-			else {
-				ptr1 = cptr->u.ttyname;
-			}
-			if (ptr1) {
-				len = snprintf(ptr, left, "%s", ptr1);
-				left -= len;
-				ptr  += len;
-				if (left <= 0)
-					break;
-			}
-		}
-
-		if (cptr->type == CNODE) {
-			if (cptr->u.conc.id) {
-				len = snprintf(ptr, left, "%s", cptr->u.conc.id);
-				left -= len;
-				ptr  += len;
-				if (left <= 0)
-					break;
-			}
-                }
-
-		if (cptr->type == MNODE) {
-			if (cptr->u.module.id) {
-				len = snprintf(ptr, left, "%s", cptr->u.module.id);
-				left -= len;
-				ptr  += len;
-				if (left <= 0)
-					break;
-			}
-		}
-	}
-
-	return string;
-}
-
-/************************************************************************
- *                      
- * TTY Initialization/Cleanup Functions
- *      
- ************************************************************************/
-         
-/*
- * dgap_tty_preinit()
- *
- * Initialize any global tty related data before we download any boards.
- */
-int dgap_tty_preinit(void)
-{
-	unsigned long flags;
-
-	DGAP_LOCK(dgap_global_lock, flags);  
-
-	/*
-	 * Allocate a buffer for doing the copy from user space to
-	 * kernel space in dgap_input().  We only use one buffer and
-	 * control access to it with a semaphore.  If we are paging, we
-	 * are already in trouble so one buffer won't hurt much anyway.
-	 */
-	dgap_TmpWriteBuf = kmalloc(WRITEBUFLEN, GFP_ATOMIC);
-
-	if (!dgap_TmpWriteBuf) {
-		DGAP_UNLOCK(dgap_global_lock, flags);
-		DPR_INIT(("unable to allocate tmp write buf"));
-		return (-ENOMEM);
-	}
-         
-        DGAP_UNLOCK(dgap_global_lock, flags);
-        return(0);
-}
-
-
-/*
- * dgap_tty_register()
- *
- * Init the tty subsystem for this board.
- */
-int dgap_tty_register(struct board_t *brd)
-{
-	int rc = 0;
-
-	DPR_INIT(("tty_register start"));
-
-	brd->SerialDriver = alloc_tty_driver(MAXPORTS);
-
-	snprintf(brd->SerialName, MAXTTYNAMELEN, "tty_dgap_%d_", brd->boardnum);
-	brd->SerialDriver->name = brd->SerialName;
-	brd->SerialDriver->name_base = 0;
-	brd->SerialDriver->major = 0;
-	brd->SerialDriver->minor_start = 0;
-	brd->SerialDriver->type = TTY_DRIVER_TYPE_SERIAL; 
-	brd->SerialDriver->subtype = SERIAL_TYPE_NORMAL;   
-	brd->SerialDriver->init_termios = DgapDefaultTermios;
-	brd->SerialDriver->driver_name = DRVSTR;
-	brd->SerialDriver->flags = (TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_HARDWARE_BREAK);
-
-	/* The kernel wants space to store pointers to tty_structs */
-	brd->SerialDriver->ttys = dgap_driver_kzmalloc(MAXPORTS * sizeof(struct tty_struct *), GFP_KERNEL);
-	if (!brd->SerialDriver->ttys)
-		return(-ENOMEM);
-
-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-	brd->SerialDriver->refcount = brd->TtyRefCnt;
-#endif
-
-	/*
-	 * Entry points for driver.  Called by the kernel from
-	 * tty_io.c and n_tty.c.
-	 */
-	tty_set_operations(brd->SerialDriver, &dgap_tty_ops);
-
-	/*
-	 * If we're doing transparent print, we have to do all of the above
-	 * again, separately so we don't get the LD confused about what major
-	 * we are when we get into the dgap_tty_open() routine.
-	 */
-	brd->PrintDriver = alloc_tty_driver(MAXPORTS);
-
-	snprintf(brd->PrintName, MAXTTYNAMELEN, "pr_dgap_%d_", brd->boardnum);
-	brd->PrintDriver->name = brd->PrintName;
-	brd->PrintDriver->name_base = 0;
-	brd->PrintDriver->major = 0;
-	brd->PrintDriver->minor_start = 0;
-	brd->PrintDriver->type = TTY_DRIVER_TYPE_SERIAL;   
-	brd->PrintDriver->subtype = SERIAL_TYPE_NORMAL;
-	brd->PrintDriver->init_termios = DgapDefaultTermios;
-	brd->PrintDriver->driver_name = DRVSTR;
-	brd->PrintDriver->flags = (TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_HARDWARE_BREAK);
-
-	/* The kernel wants space to store pointers to tty_structs */
-	brd->PrintDriver->ttys = dgap_driver_kzmalloc(MAXPORTS * sizeof(struct tty_struct *), GFP_KERNEL);
-	if (!brd->PrintDriver->ttys)
-		return(-ENOMEM);
-
-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-	brd->PrintDriver->refcount = brd->TtyRefCnt;
-#endif
-
-	/*
-	 * Entry points for driver.  Called by the kernel from
-	 * tty_io.c and n_tty.c.
-	 */
-	tty_set_operations(brd->PrintDriver, &dgap_tty_ops);
-
-	if (!brd->dgap_Major_Serial_Registered) {
-		/* Register tty devices */
-		rc = tty_register_driver(brd->SerialDriver);
-		if (rc < 0) {
-			APR(("Can't register tty device (%d)\n", rc));
-			return(rc);
-		}
-		brd->dgap_Major_Serial_Registered = TRUE;
-		dgap_BoardsByMajor[brd->SerialDriver->major] = brd;
-		brd->dgap_Serial_Major = brd->SerialDriver->major;
-	}
-
-	if (!brd->dgap_Major_TransparentPrint_Registered) {
-		/* Register Transparent Print devices */
- 		rc = tty_register_driver(brd->PrintDriver);
-		if (rc < 0) {
-			APR(("Can't register Transparent Print device (%d)\n", rc));
-			return(rc);
-		}
-		brd->dgap_Major_TransparentPrint_Registered = TRUE;
-		dgap_BoardsByMajor[brd->PrintDriver->major] = brd;
-		brd->dgap_TransparentPrint_Major = brd->PrintDriver->major;
-	}
-
-	DPR_INIT(("DGAP REGISTER TTY: MAJORS: %d %d\n", brd->SerialDriver->major,
-		brd->PrintDriver->major));
-
-	return (rc);
-}
-
-
-/*
- * dgap_tty_init()
- *
- * Init the tty subsystem.  Called once per board after board has been
- * downloaded and init'ed.
- */
-int dgap_tty_init(struct board_t *brd)
-{
-	int i;
-	int tlw;
-	uint true_count = 0;
-	uchar *vaddr;
-	uchar modem = 0;
-	struct channel_t *ch;
-	struct bs_t *bs;
-	struct cm_t *cm;
-
-	if (!brd)
-		return (-ENXIO);
-
-	DPR_INIT(("dgap_tty_init start\n"));
-
-	/*
-	 * Initialize board structure elements.
-	 */
-
-	vaddr = brd->re_map_membase;
-	true_count = readw((vaddr + NCHAN));
-
-	brd->nasync = dgap_config_get_number_of_ports(brd);
-
-	if (!brd->nasync) {
-		brd->nasync = brd->maxports;
-	}
-
-	if (brd->nasync > brd->maxports) {
-		brd->nasync = brd->maxports;
-	}
-
-	if (true_count != brd->nasync) {
-		if ((brd->type == PPCM) && (true_count == 64)) {
-			APR(("***WARNING**** %s configured for %d ports, has %d ports.\nPlease make SURE the EBI cable running from the card\nto each EM module is plugged into EBI IN!\n",
-				brd->name, brd->nasync, true_count));
-		}
-		else if ((brd->type == PPCM) && (true_count == 0)) {
-			APR(("***WARNING**** %s configured for %d ports, has %d ports.\nPlease make SURE the EBI cable running from the card\nto each EM module is plugged into EBI IN!\n",
-				brd->name, brd->nasync, true_count));
-		}
-		else {
-			APR(("***WARNING**** %s configured for %d ports, has %d ports.\n",
-				brd->name, brd->nasync, true_count));
-		}
-
-		brd->nasync = true_count;
-
-		/* If no ports, don't bother going any further */
-		if (!brd->nasync) {
-			brd->state = BOARD_FAILED;
-			brd->dpastatus = BD_NOFEP;
-			return(-ENXIO);
-		}
-	}
-
-	/*
-	 * Allocate channel memory that might not have been allocated
-	 * when the driver was first loaded.
-	 */
-	for (i = 0; i < brd->nasync; i++) {
-		if (!brd->channels[i]) {
-			brd->channels[i] = dgap_driver_kzmalloc(sizeof(struct channel_t), GFP_ATOMIC);
-			if (!brd->channels[i]) {
-				DPR_CORE(("%s:%d Unable to allocate memory for channel struct\n",
-				    __FILE__, __LINE__));
-			}
-		}
-	}
-
-	ch = brd->channels[0];
-	vaddr = brd->re_map_membase;
-
-	bs = (struct bs_t *) ((ulong) vaddr + CHANBUF);
-	cm = (struct cm_t *) ((ulong) vaddr + CMDBUF);
-
-	brd->bd_bs = bs;
-
-	/* Set up channel variables */
-	for (i = 0; i < brd->nasync; i++, ch = brd->channels[i], bs++) {
-
-		if (!brd->channels[i])
-			continue;
-
-		DGAP_SPINLOCK_INIT(ch->ch_lock);
-
-		/* Store all our magic numbers */
-		ch->magic = DGAP_CHANNEL_MAGIC;
-		ch->ch_tun.magic = DGAP_UNIT_MAGIC;
-		ch->ch_tun.un_type = DGAP_SERIAL;
-		ch->ch_tun.un_ch = ch;
-		ch->ch_tun.un_dev = i;
-
-		ch->ch_pun.magic = DGAP_UNIT_MAGIC;
-		ch->ch_pun.un_type = DGAP_PRINT;
-		ch->ch_pun.un_ch = ch;
-		ch->ch_pun.un_dev = i;
-
-		ch->ch_vaddr = vaddr;
-		ch->ch_bs = bs;
-		ch->ch_cm = cm;
-		ch->ch_bd = brd;
-		ch->ch_portnum = i;
-		ch->ch_digi = dgap_digi_init;
-
-		/*
-		 * Set up digi dsr and dcd bits based on altpin flag.
-		 */
-		if (dgap_config_get_altpin(brd)) {
-			ch->ch_dsr	= DM_CD;
-			ch->ch_cd	= DM_DSR;
-			ch->ch_digi.digi_flags |= DIGI_ALTPIN;
-		}
-		else {
-			ch->ch_cd	= DM_CD;
-			ch->ch_dsr	= DM_DSR;
-		}
-
-		ch->ch_taddr = vaddr + ((ch->ch_bs->tx_seg) << 4);
-		ch->ch_raddr = vaddr + ((ch->ch_bs->rx_seg) << 4);
-		ch->ch_tx_win = 0;
-		ch->ch_rx_win = 0;
-		ch->ch_tsize = readw(&(ch->ch_bs->tx_max)) + 1;
-		ch->ch_rsize = readw(&(ch->ch_bs->rx_max)) + 1;
-		ch->ch_tstart = 0;
-		ch->ch_rstart = 0;
-
-		/* .25 second delay */
-		ch->ch_close_delay = 250;
-
-		/*
-		 * Set queue water marks, interrupt mask,
-		 * and general tty parameters. 
-		 */
-		ch->ch_tlw = tlw = ch->ch_tsize >= 2000 ? ((ch->ch_tsize * 5) / 8) : ch->ch_tsize / 2;
-
-		dgap_cmdw(ch, STLOW, tlw, 0);
-
-		dgap_cmdw(ch, SRLOW, ch->ch_rsize / 2, 0);
-
-		dgap_cmdw(ch, SRHIGH, 7 * ch->ch_rsize / 8, 0);
-
-		ch->ch_mistat = readb(&(ch->ch_bs->m_stat));
-
-		init_waitqueue_head(&ch->ch_flags_wait);
-		init_waitqueue_head(&ch->ch_tun.un_flags_wait);
-		init_waitqueue_head(&ch->ch_pun.un_flags_wait);
-		init_waitqueue_head(&ch->ch_sniff_wait);
-
-		/* Turn on all modem interrupts for now */
-		modem = (DM_CD | DM_DSR | DM_CTS | DM_RI);
-		writeb(modem, &(ch->ch_bs->m_int));
-
-		/*
-		 * Set edelay to 0 if interrupts are turned on,
-		 * otherwise set edelay to the usual 100.
-		 */
-		if (brd->intr_used)
-			writew(0, &(ch->ch_bs->edelay));
-		else
-			writew(100, &(ch->ch_bs->edelay));
-	
-		writeb(1, &(ch->ch_bs->idata));
-	}
-
-
-	DPR_INIT(("dgap_tty_init finish\n"));
-
-	return (0);
-}
-
-
-/*
- * dgap_tty_post_uninit()
- *
- * UnInitialize any global tty related data.
- */
-void dgap_tty_post_uninit(void)
-{
-	kfree(dgap_TmpWriteBuf);
-	dgap_TmpWriteBuf = NULL;
-}
-
-
-/*
- * dgap_tty_uninit()
- *
- * Uninitialize the TTY portion of this driver.  Free all memory and
- * resources. 
- */
-void dgap_tty_uninit(struct board_t *brd)
-{
-	int i = 0;
-
-	if (brd->dgap_Major_Serial_Registered) {
-		dgap_BoardsByMajor[brd->SerialDriver->major] = NULL;
-		brd->dgap_Serial_Major = 0;
-		for (i = 0; i < brd->nasync; i++) {
-			dgap_remove_tty_sysfs(brd->channels[i]->ch_tun.un_sysfs);
-			tty_unregister_device(brd->SerialDriver, i);
-		}
-		tty_unregister_driver(brd->SerialDriver);
-		kfree(brd->SerialDriver->ttys);
-		brd->SerialDriver->ttys = NULL;
-		put_tty_driver(brd->SerialDriver);
-		brd->dgap_Major_Serial_Registered = FALSE;
-	}
-
-	if (brd->dgap_Major_TransparentPrint_Registered) {
-		dgap_BoardsByMajor[brd->PrintDriver->major] = NULL;
-		brd->dgap_TransparentPrint_Major = 0;
-		for (i = 0; i < brd->nasync; i++) {
-			dgap_remove_tty_sysfs(brd->channels[i]->ch_pun.un_sysfs);
-			tty_unregister_device(brd->PrintDriver, i);
-		}
-		tty_unregister_driver(brd->PrintDriver);
-		kfree(brd->PrintDriver->ttys);
-		brd->PrintDriver->ttys = NULL;
-		put_tty_driver(brd->PrintDriver);
-		brd->dgap_Major_TransparentPrint_Registered = FALSE;
-	}
-}
-
-
-#define TMPBUFLEN (1024)
-
-/*
- * dgap_sniff - Dump data out to the "sniff" buffer if the
- * proc sniff file is opened...
- */
-static void dgap_sniff_nowait_nolock(struct channel_t *ch, uchar *text, uchar *buf, int len)
-{
-	struct timeval tv;
-	int n;
-	int r;
-	int nbuf;
-	int i;
-	int tmpbuflen;
-	char tmpbuf[TMPBUFLEN];
-	char *p = tmpbuf;
-	int too_much_data;
-
-	/* Leave if sniff not open */
-	if (!(ch->ch_sniff_flags & SNIFF_OPEN))
-		return;
-
-	do_gettimeofday(&tv);
-
-	/* Create our header for data dump */
-	p += sprintf(p, "<%ld %ld><%s><", tv.tv_sec, tv.tv_usec, text);
-	tmpbuflen = p - tmpbuf;
-
-	do {
-		too_much_data = 0;
-
-		for (i = 0; i < len && tmpbuflen < (TMPBUFLEN - 4); i++) {
-			p += sprintf(p, "%02x ", *buf);
-			buf++;
-			tmpbuflen = p - tmpbuf;
-		}
-
-		if (tmpbuflen < (TMPBUFLEN - 4)) {
-			if (i > 0)
-				p += sprintf(p - 1, "%s\n", ">");
-			else
-				p += sprintf(p, "%s\n", ">");
-		} else {
-			too_much_data = 1;
-			len -= i;
-		}
-
-		nbuf = strlen(tmpbuf);
-		p = tmpbuf;
-
-		/*
-		 *  Loop while data remains.
-		 */
-		while (nbuf > 0 && ch->ch_sniff_buf) {
-			/*
-			 *  Determine the amount of available space left in the
-			 *  buffer.  If there's none, wait until some appears.
-			 */
-			n = (ch->ch_sniff_out - ch->ch_sniff_in - 1) & SNIFF_MASK;
-
-			/*
-			 * If there is no space left to write to in our sniff buffer,
-			 * we have no choice but to drop the data.
-			 * We *cannot* sleep here waiting for space, because this
-			 * function was probably called by the interrupt/timer routines!
-			 */
-			if (n == 0) {
-				return;
-			}
-	
-			/*
-			 * Copy as much data as will fit.
-			 */
-
-			if (n > nbuf)
-				n = nbuf;
-
-			r = SNIFF_MAX - ch->ch_sniff_in;
-
-			if (r <= n) {
-				memcpy(ch->ch_sniff_buf + ch->ch_sniff_in, p, r);
-
-				n -= r;
-				ch->ch_sniff_in = 0;
-				p += r;
-				nbuf -= r;
-			}
-
-			memcpy(ch->ch_sniff_buf + ch->ch_sniff_in, p, n);
-
-			ch->ch_sniff_in += n;
-			p += n;
-			nbuf -= n;
-
-			/*
-			 *  Wakeup any thread waiting for data
-			 */
-			if (ch->ch_sniff_flags & SNIFF_WAIT_DATA) {
-				ch->ch_sniff_flags &= ~SNIFF_WAIT_DATA;
-				wake_up_interruptible(&ch->ch_sniff_wait);
-			}
-		}
-
-		/*
-		 * If the user sent us too much data to push into our tmpbuf,
-		 * we need to keep looping around on all the data.
-		 */
-		if (too_much_data) {
-			p = tmpbuf;
-			tmpbuflen = 0;
-		}
-
-	} while (too_much_data);
-}
-
-
-/*=======================================================================
- *
- *      dgap_input - Process received data.
- * 
- *              ch      - Pointer to channel structure.
- * 
- *=======================================================================*/
-
-void dgap_input(struct channel_t *ch)
-{
-	struct board_t *bd;
-	struct bs_t	*bs;
-	struct tty_struct *tp;
-	struct tty_ldisc *ld;
-	uint	rmask;
-	uint	head;
-	uint	tail;
-	int	data_len;
-	ulong	lock_flags;
-	ulong   lock_flags2;
-	int flip_len;
-	int len = 0;
-	int n = 0;
-	uchar *buf;
-	uchar tmpchar;
-	int s = 0;
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	tp = ch->ch_tun.un_tty;
-
-	bs  = ch->ch_bs;
-	if (!bs) {
-		return;
-	}
-
-	bd = ch->ch_bd;
-	if(!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_READ(("dgap_input start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	/* 
-	 *      Figure the number of characters in the buffer.   
-	 *      Exit immediately if none.
-	 */
-
-	rmask = ch->ch_rsize - 1;
-
-	head = readw(&(bs->rx_head));
-	head &= rmask;
-	tail = readw(&(bs->rx_tail));
-	tail &= rmask;
-
-	data_len = (head - tail) & rmask;
-
-	if (data_len == 0) {
-		writeb(1, &(bs->idata));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		DPR_READ(("No data on port %d\n", ch->ch_portnum));
-		return;
-	}
-
-	/*
-	 * If the device is not open, or CREAD is off, flush
-	 * input data and return immediately.
-	 */
-	if ((bd->state != BOARD_READY) || !tp  || (tp->magic != TTY_MAGIC) ||
-            !(ch->ch_tun.un_flags & UN_ISOPEN) || !(tp->termios.c_cflag & CREAD) ||
-	    (ch->ch_tun.un_flags & UN_CLOSING)) {
-
-		DPR_READ(("input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum));
-		DPR_READ(("input. tp: %p tp->magic: %x MAGIC:%x ch flags: %x\n",
-			tp, tp ? tp->magic : 0, TTY_MAGIC, ch->ch_tun.un_flags));
-		writew(head, &(bs->rx_tail));
-		writeb(1, &(bs->idata));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return;
-	}
-
-	/*
-	 * If we are throttled, simply don't read any data.
-	 */
-	if (ch->ch_flags & CH_RXBLOCK) {
-		writeb(1, &(bs->idata));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		DPR_READ(("Port %d throttled, not reading any data. head: %x tail: %x\n",
-			ch->ch_portnum, head, tail));
-		return;
-	}
-
-	/*
-	 *      Ignore oruns.
-	 */
-	tmpchar = readb(&(bs->orun));
-	if (tmpchar) {
-		ch->ch_err_overrun++;
-		writeb(0, &(bs->orun));
-	}
-
-	DPR_READ(("dgap_input start 2\n"));
-
-	/* Decide how much data we can send into the tty layer */
-	flip_len = TTY_FLIPBUF_SIZE;
-
-	/* Chop down the length, if needed */
-	len = min(data_len, flip_len);
-	len = min(len, (N_TTY_BUF_SIZE - 1));
-
-	ld = tty_ldisc_ref(tp);
-                
-#ifdef TTY_DONT_FLIP
-	/*
-	 * If the DONT_FLIP flag is on, don't flush our buffer, and act
-	 * like the ld doesn't have any space to put the data right now.  
-	 */
-	if (test_bit(TTY_DONT_FLIP, &tp->flags))   
-		len = 0;
-#endif
-
-	/*
-	 * If we were unable to get a reference to the ld,
-	 * don't flush our buffer, and act like the ld doesn't
-	 * have any space to put the data right now.
-	 */
-	if (!ld) {
-		len = 0;
-	} else {
-		/*
-		 * If ld doesn't have a pointer to a receive_buf function,
-		 * flush the data, then act like the ld doesn't have any
-		 * space to put the data right now.
-		 */
-		if (!ld->ops->receive_buf) {
-			writew(head, &(bs->rx_tail));
-			len = 0;
-		}
-	}
-
-	if (len <= 0) {
-		writeb(1, &(bs->idata));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		DPR_READ(("dgap_input 1 - finish\n"));
-		if (ld)
-			tty_ldisc_deref(ld);
-		return;
-	}
-
-	buf = ch->ch_bd->flipbuf;
-	n = len;
-
-	/*
-	 * n now contains the most amount of data we can copy,
-	 * bounded either by our buffer size or the amount
-	 * of data the card actually has pending...
-	 */
-	while (n) {
-
-		s = ((head >= tail) ? head : ch->ch_rsize) - tail;
-		s = min(s, n);
-
-		if (s <= 0)
-			break;
-
-		memcpy_fromio(buf, (char *) ch->ch_raddr + tail, s);
-		dgap_sniff_nowait_nolock(ch, "USER READ", buf, s);
-
-		tail += s;
-		buf += s;
-
-		n -= s;
-		/* Flip queue if needed */
-		tail &= rmask;
-	}
-
-	writew(tail, &(bs->rx_tail));
-	writeb(1, &(bs->idata));
-	ch->ch_rxcount += len;
-
-	/*
-	 * If we are completely raw, we don't need to go through a lot
-	 * of the tty layers that exist.
-	 * In this case, we take the shortest and fastest route we
-	 * can to relay the data to the user.
-	 *
-	 * On the other hand, if we are not raw, we need to go through
-	 * the tty layer, which has its API more well defined.
-	 */
-	if (I_PARMRK(tp) || I_BRKINT(tp) || I_INPCK(tp)) {
-		dgap_parity_scan(ch, ch->ch_bd->flipbuf, ch->ch_bd->flipflagbuf, &len);
-
-		len = tty_buffer_request_room(tp->port, len);
-		tty_insert_flip_string_flags(tp->port, ch->ch_bd->flipbuf,
-			ch->ch_bd->flipflagbuf, len);
-	}
-	else {
-		len = tty_buffer_request_room(tp->port, len);
-		tty_insert_flip_string(tp->port, ch->ch_bd->flipbuf, len);
-	}
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	/* Tell the tty layer its okay to "eat" the data now */
-	tty_flip_buffer_push(tp->port);
-
-	if (ld)
-		tty_ldisc_deref(ld);
-
-	DPR_READ(("dgap_input - finish\n"));
-}
-
-
-/************************************************************************   
- * Determines when CARRIER changes state and takes appropriate
- * action. 
- ************************************************************************/
-void dgap_carrier(struct channel_t *ch)
-{
-	struct board_t *bd;
-
-        int virt_carrier = 0;
-        int phys_carrier = 0;
- 
-	DPR_CARR(("dgap_carrier called...\n"));
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	bd = ch->ch_bd;
-
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	/* Make sure altpin is always set correctly */
-	if (ch->ch_digi.digi_flags & DIGI_ALTPIN) {
-		ch->ch_dsr      = DM_CD;
-		ch->ch_cd       = DM_DSR;
-	}
-	else {
-		ch->ch_dsr      = DM_DSR;
-		ch->ch_cd       = DM_CD;
-	}
-
-	if (ch->ch_mistat & D_CD(ch)) {
-		DPR_CARR(("mistat: %x  D_CD: %x\n", ch->ch_mistat, D_CD(ch)));
-		phys_carrier = 1;
-	}
-
-	if (ch->ch_digi.digi_flags & DIGI_FORCEDCD) {
-		virt_carrier = 1;
-	}  
-
-	if (ch->ch_c_cflag & CLOCAL) {
-		virt_carrier = 1;
-	}  
-
-
-	DPR_CARR(("DCD: physical: %d virt: %d\n", phys_carrier, virt_carrier));
-
-	/*
-	 * Test for a VIRTUAL carrier transition to HIGH.
-	 */
-	if (((ch->ch_flags & CH_FCAR) == 0) && (virt_carrier == 1)) {
-
-		/*
-		 * When carrier rises, wake any threads waiting
-		 * for carrier in the open routine.
-		 */
-
-		DPR_CARR(("carrier: virt DCD rose\n"));
-
-		if (waitqueue_active(&(ch->ch_flags_wait)))
-			wake_up_interruptible(&ch->ch_flags_wait);
-	}
-
-	/*
-	 * Test for a PHYSICAL carrier transition to HIGH.
-	 */
-	if (((ch->ch_flags & CH_CD) == 0) && (phys_carrier == 1)) {
-
-		/*
-		 * When carrier rises, wake any threads waiting
-		 * for carrier in the open routine.
-		 */
-
-		DPR_CARR(("carrier: physical DCD rose\n"));
-
-		if (waitqueue_active(&(ch->ch_flags_wait)))
-			wake_up_interruptible(&ch->ch_flags_wait);
-	}
-
-	/*
-	 *  Test for a PHYSICAL transition to low, so long as we aren't
-	 *  currently ignoring physical transitions (which is what "virtual
-	 *  carrier" indicates).
-	 *
-	 *  The transition of the virtual carrier to low really doesn't
-	 *  matter... it really only means "ignore carrier state", not
-	 *  "make pretend that carrier is there".
-	 */
-	if ((virt_carrier == 0) && ((ch->ch_flags & CH_CD) != 0) &&
-	    (phys_carrier == 0)) 
-	{
-
-		/*
-		 *   When carrier drops:
-		 *
-		 *   Drop carrier on all open units.
-		 *
-		 *   Flush queues, waking up any task waiting in the
-		 *   line discipline.
-		 *
-		 *   Send a hangup to the control terminal.
-		 *
-		 *   Enable all select calls.
-		 */
-		if (waitqueue_active(&(ch->ch_flags_wait)))
-			wake_up_interruptible(&ch->ch_flags_wait);
-
-		if (ch->ch_tun.un_open_count > 0) {
-			DPR_CARR(("Sending tty hangup\n"));
-			tty_hangup(ch->ch_tun.un_tty);
-		}
-
-		if (ch->ch_pun.un_open_count > 0) { 
-			DPR_CARR(("Sending pr hangup\n"));
-			tty_hangup(ch->ch_pun.un_tty);
-		}
-	}
-
-	/*
-	 *  Make sure that our cached values reflect the current reality.
-	 */
-	if (virt_carrier == 1)
-		ch->ch_flags |= CH_FCAR;
-	else      
-		ch->ch_flags &= ~CH_FCAR;
-
-	if (phys_carrier == 1)
-		ch->ch_flags |= CH_CD;
-	else
-		ch->ch_flags &= ~CH_CD;
-}
-
-
-/************************************************************************
- *      
- * TTY Entry points and helper functions
- *              
- ************************************************************************/
-
-/*
- * dgap_tty_open()
- *
- */
-static int dgap_tty_open(struct tty_struct *tty, struct file *file)
-{
-	struct board_t	*brd;
-	struct channel_t *ch;
-	struct un_t	*un;
-	struct bs_t	*bs;
-	uint		major = 0;
-	uint		minor = 0;
-	int		rc = 0;
-	ulong		lock_flags;
-	ulong		lock_flags2;
-	u16		head;
-
-	rc = 0;
-
-	major = MAJOR(tty_devnum(tty));
-	minor = MINOR(tty_devnum(tty));
-
-	if (major > 255) {
-		return -ENXIO;
-	}
-
-	/* Get board pointer from our array of majors we have allocated */
-	brd = dgap_BoardsByMajor[major];
-	if (!brd) {
-		return -ENXIO;
-	}
-
-	/*
-	 * If board is not yet up to a state of READY, go to
-	 * sleep waiting for it to happen or they cancel the open.
-	 */
-	rc = wait_event_interruptible(brd->state_wait,
-		(brd->state & BOARD_READY));
-
-	if (rc) {
-		return rc;
-	}
-
-	DGAP_LOCK(brd->bd_lock, lock_flags);
-
-	/* The wait above should guarantee this cannot happen */
-	if (brd->state != BOARD_READY) {
-		DGAP_UNLOCK(brd->bd_lock, lock_flags);
-		return -ENXIO;
-	}
-
-	/* If opened device is greater than our number of ports, bail. */
-	if (MINOR(tty_devnum(tty)) > brd->nasync) {
-		DGAP_UNLOCK(brd->bd_lock, lock_flags);
-		return -ENXIO;
-	}
-
-	ch = brd->channels[minor];
-	if (!ch) {
-		DGAP_UNLOCK(brd->bd_lock, lock_flags);
-		return -ENXIO;
-	}
-
-	/* Grab channel lock */
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	/* Figure out our type */
-	if (major == brd->dgap_Serial_Major) {
-		un = &brd->channels[minor]->ch_tun;
-		un->un_type = DGAP_SERIAL;
-	}
-	else if (major == brd->dgap_TransparentPrint_Major) {
-		un = &brd->channels[minor]->ch_pun;
-		un->un_type = DGAP_PRINT;
-	}
-	else {
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(brd->bd_lock, lock_flags);
-		DPR_OPEN(("%d Unknown TYPE!\n", __LINE__));
-		return -ENXIO;
-	}
-
-	/* Store our unit into driver_data, so we always have it available. */
-	tty->driver_data = un;
-
-	DPR_OPEN(("Open called. MAJOR: %d MINOR:%d unit: %p NAME: %s\n",
-		MAJOR(tty_devnum(tty)), MINOR(tty_devnum(tty)), un, brd->name));
-
-	/*
-	 * Error if channel info pointer is NULL.
-	 */
-	bs = ch->ch_bs;
-	if (!bs) {
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(brd->bd_lock, lock_flags);
-		DPR_OPEN(("%d BS is 0!\n", __LINE__));
-		return -ENXIO;
-        }
-
-	DPR_OPEN(("%d: tflag=%x  pflag=%x\n", __LINE__, ch->ch_tun.un_flags, ch->ch_pun.un_flags));
-
-	/*
-	 * Initialize tty's
-	 */
-	if (!(un->un_flags & UN_ISOPEN)) {
-		/* Store important variables. */
-		un->un_tty     = tty;
-
-		/* Maybe do something here to the TTY struct as well? */
-	}
-
-	/*
-	 * Initialize if neither terminal or printer is open.
-	 */
-	if (!((ch->ch_tun.un_flags | ch->ch_pun.un_flags) & UN_ISOPEN)) {
-
-		DPR_OPEN(("dgap_open: initializing channel in open...\n"));
-
-		ch->ch_mforce = 0;
-		ch->ch_mval = 0;
-
-		/*
-		 * Flush input queue.
-		 */
-		head = readw(&(bs->rx_head));
-		writew(head, &(bs->rx_tail));
-
-		ch->ch_flags = 0;
-		ch->pscan_state = 0;
-		ch->pscan_savechar = 0;
-
-		ch->ch_c_cflag   = tty->termios.c_cflag;
-		ch->ch_c_iflag   = tty->termios.c_iflag;
-		ch->ch_c_oflag   = tty->termios.c_oflag;
-		ch->ch_c_lflag   = tty->termios.c_lflag;
-		ch->ch_startc = tty->termios.c_cc[VSTART];
-		ch->ch_stopc  = tty->termios.c_cc[VSTOP];
-
-		/* TODO: flush our TTY struct here? */
-	}
-
-	dgap_carrier(ch);
-	/*
-	 * Run param in case we changed anything
-	 */
-	dgap_param(tty);
-
-	/*                              
-	 * follow protocol for opening port
-	 */
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(brd->bd_lock, lock_flags);
-
-	rc = dgap_block_til_ready(tty, file, ch);
-
-	if (!un->un_tty) {
-		return -ENODEV;
-	}
-
-	if (rc) {
-		DPR_OPEN(("dgap_tty_open returning after dgap_block_til_ready "
-			"with %d\n", rc));
-	}
-
-	/* No going back now, increment our unit and channel counters */
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-	ch->ch_open_count++;
-	un->un_open_count++;
-	un->un_flags |= (UN_ISOPEN);
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	DPR_OPEN(("dgap_tty_open finished\n"));
-	return (rc);
-}
-
-
-/*   
- * dgap_block_til_ready()
- *
- * Wait for DCD, if needed.
- */
-static int dgap_block_til_ready(struct tty_struct *tty, struct file *file, struct channel_t *ch)
-{ 
-	int retval = 0;
-	struct un_t *un = NULL;
-	ulong   lock_flags;
-	uint	old_flags = 0;
-	int sleep_on_un_flags = 0;
-
-	if (!tty || tty->magic != TTY_MAGIC || !file || !ch || ch->magic != DGAP_CHANNEL_MAGIC) {
-		return (-ENXIO);
-	}
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC) {
-		return (-ENXIO);
-	}
-
-	DPR_OPEN(("dgap_block_til_ready - before block.\n"));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	ch->ch_wopen++;
-
-	/* Loop forever */
-	while (1) {
-
-		sleep_on_un_flags = 0;
-
-		/*
-		 * If board has failed somehow during our sleep, bail with error.
-		 */
-		if (ch->ch_bd->state == BOARD_FAILED) {
-			retval = -ENXIO;
-			break;
-		}
-
-		/* If tty was hung up, break out of loop and set error. */
-		if (tty_hung_up_p(file)) {
-			retval = -EAGAIN;
-			break;
-		}
-
-		/*
-		 * If either unit is in the middle of the fragile part of close,
-		 * we just cannot touch the channel safely.
-		 * Go back to sleep, knowing that when the channel can be
-		 * touched safely, the close routine will signal the 
-		 * ch_wait_flags to wake us back up.
-		 */
-		if (!((ch->ch_tun.un_flags | ch->ch_pun.un_flags) & UN_CLOSING)) {
-
-			/*
-			 * Our conditions to leave cleanly and happily:
-			 * 1) NONBLOCKING on the tty is set.
-			 * 2) CLOCAL is set.
-			 * 3) DCD (fake or real) is active.
-			 */
-
-			if (file->f_flags & O_NONBLOCK) {
-				break;
-			}
-
-			if (tty->flags & (1 << TTY_IO_ERROR)) {
-				break;
-			}
-
-			if (ch->ch_flags & CH_CD) {
-				DPR_OPEN(("%d: ch_flags: %x\n", __LINE__, ch->ch_flags));
-				break;
-			}
-
-			if (ch->ch_flags & CH_FCAR) {
-				DPR_OPEN(("%d: ch_flags: %x\n", __LINE__, ch->ch_flags));
-				break;
-			}
-		}
-		else {
-			sleep_on_un_flags = 1;
-		}
-
-		/*
-		 * If there is a signal pending, the user probably
-		 * interrupted (ctrl-c) us.
-		 * Leave loop with error set.
-		 */
-		if (signal_pending(current)) {
-			DPR_OPEN(("%d: signal pending...\n", __LINE__));
-			retval = -ERESTARTSYS;
-			break;
-		}
-
-		DPR_OPEN(("dgap_block_til_ready - blocking.\n"));
-
-		/*
-		 * Store the flags before we let go of channel lock
-		 */
-		if (sleep_on_un_flags)
-			old_flags = ch->ch_tun.un_flags | ch->ch_pun.un_flags;
-		else
-			old_flags = ch->ch_flags;
-
-		/*
-		 * Let go of channel lock before calling schedule.
-		 * Our poller will get any FEP events and wake us up when DCD
-		 * eventually goes active.
-		 */
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-		DPR_OPEN(("Going to sleep on %s flags...\n",
-			(sleep_on_un_flags ? "un" : "ch")));
-
-		/*
-		 * Wait for something in the flags to change from the current value.
-		 */
-		if (sleep_on_un_flags) {
-			retval = wait_event_interruptible(un->un_flags_wait,
-				(old_flags != (ch->ch_tun.un_flags | ch->ch_pun.un_flags)));
-		}
-		else {
-			retval = wait_event_interruptible(ch->ch_flags_wait,
-				(old_flags != ch->ch_flags));
-		}
-
-		DPR_OPEN(("After sleep... retval: %x\n", retval));
-
-		/*
-		 * We got woken up for some reason.
-		 * Before looping around, grab our channel lock.
-		 */
-		DGAP_LOCK(ch->ch_lock, lock_flags);
-	}
-
-	ch->ch_wopen--;
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	DPR_OPEN(("dgap_block_til_ready - after blocking.\n"));
-
-	if (retval) {
-		DPR_OPEN(("dgap_block_til_ready - done. error. retval: %x\n", retval));
-		return(retval);
-	}
-
-	DPR_OPEN(("dgap_block_til_ready - done no error. jiffies: %lu\n", jiffies));
-
-	return(0);
-}
-
-
-/*
- * dgap_tty_hangup()
- *
- * Hangup the port.  Like a close, but don't wait for output to drain.
- */     
-static void dgap_tty_hangup(struct tty_struct *tty)
-{
-	struct board_t	*bd;
-	struct channel_t *ch;
-	struct un_t	*un;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_CLOSE(("dgap_hangup called. ch->ch_open_count: %d un->un_open_count: %d\n",
-		ch->ch_open_count, un->un_open_count));
-
-	/* flush the transmit queues */
-	dgap_tty_flush_buffer(tty);
-
-	DPR_CLOSE(("dgap_hangup finished. ch->ch_open_count: %d un->un_open_count: %d\n",
-		ch->ch_open_count, un->un_open_count));
-}
-
-
-
-/*
- * dgap_tty_close()
- *
- */
-static void dgap_tty_close(struct tty_struct *tty, struct file *file)
-{
-	struct ktermios *ts;
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong lock_flags;
-	int rc = 0;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	ts = &tty->termios;
-
-	DPR_CLOSE(("Close called\n"));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	/*
-	 * Determine if this is the last close or not - and if we agree about
-	 * which type of close it is with the Line Discipline
-	 */
-	if ((tty->count == 1) && (un->un_open_count != 1)) {
-		/*
-		 * Uh, oh.  tty->count is 1, which means that the tty
-		 * structure will be freed.  un_open_count should always
-		 * be one in these conditions.  If it's greater than
-		 * one, we've got real problems, since it means the
-		 * serial port won't be shutdown.
-		 */
-		APR(("tty->count is 1, un open count is %d\n", un->un_open_count));
-		un->un_open_count = 1;
-	}  
-
-	if (--un->un_open_count < 0) {
-		APR(("bad serial port open count of %d\n", un->un_open_count));
-		un->un_open_count = 0;
-	}
-
-	ch->ch_open_count--;
-
-	if (ch->ch_open_count && un->un_open_count) {
-		DPR_CLOSE(("dgap_tty_close: not last close ch: %d un:%d\n",
-			ch->ch_open_count, un->un_open_count));
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-                return;
-        }
-
-	/* OK, its the last close on the unit */
-	DPR_CLOSE(("dgap_tty_close - last close on unit procedures\n"));
-
-	un->un_flags |= UN_CLOSING;
-
-	tty->closing = 1;
-
-	/*
-	 * Only officially close channel if count is 0 and
-         * DIGI_PRINTER bit is not set.
-	 */
-	if ((ch->ch_open_count == 0) && !(ch->ch_digi.digi_flags & DIGI_PRINTER)) {
-
-		ch->ch_flags &= ~(CH_RXBLOCK);
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-		/* wait for output to drain */
-		/* This will also return if we take an interrupt */
-
-		DPR_CLOSE(("Calling wait_for_drain\n"));
-		rc = dgap_wait_for_drain(tty);
-		DPR_CLOSE(("After calling wait_for_drain\n"));
-
-		if (rc) {
-			DPR_BASIC(("dgap_tty_close - bad return: %d ", rc));
-		}
-
-		dgap_tty_flush_buffer(tty);
-		tty_ldisc_flush(tty);
-
-		DGAP_LOCK(ch->ch_lock, lock_flags);
-
-		tty->closing = 0;
-
-		/*
-		 * If we have HUPCL set, lower DTR and RTS
-		 */
-		if (ch->ch_c_cflag & HUPCL ) {
-			DPR_CLOSE(("Close. HUPCL set, dropping DTR/RTS\n"));
-			ch->ch_mostat &= ~(D_RTS(ch)|D_DTR(ch));
-			dgap_cmdb( ch, SMODEM, 0, D_DTR(ch)|D_RTS(ch), 0 );
-
-			/*
-			 * Go to sleep to ensure RTS/DTR 
-			 * have been dropped for modems to see it.
-			 */
-			if (ch->ch_close_delay) {
-				DPR_CLOSE(("Close. Sleeping for RTS/DTR drop\n"));
-
-				DGAP_UNLOCK(ch->ch_lock, lock_flags);
-				dgap_ms_sleep(ch->ch_close_delay);
-				DGAP_LOCK(ch->ch_lock, lock_flags);
-
-				DPR_CLOSE(("Close. After sleeping for RTS/DTR drop\n"));
-			}
-		}
-
-		ch->pscan_state = 0;
-		ch->pscan_savechar = 0;
-		ch->ch_baud_info = 0;
-
-	}
-
-	/*
-	 * turn off print device when closing print device.
-	 */
-	if ((un->un_type == DGAP_PRINT)  && (ch->ch_flags & CH_PRON) ) {
-		dgap_wmove(ch, ch->ch_digi.digi_offstr,
-			(int) ch->ch_digi.digi_offlen);
-		ch->ch_flags &= ~CH_PRON;
-	}
-
-	un->un_tty = NULL;
-	un->un_flags &= ~(UN_ISOPEN | UN_CLOSING);
-	tty->driver_data = NULL;
-
-	DPR_CLOSE(("Close. Doing wakeups\n"));
-	wake_up_interruptible(&ch->ch_flags_wait);
-	wake_up_interruptible(&un->un_flags_wait);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-                
-        DPR_BASIC(("dgap_tty_close - complete\n"));
-}
-
-
-/*
- * dgap_tty_chars_in_buffer()
- *
- * Return number of characters that have not been transmitted yet.
- *
- * This routine is used by the line discipline to determine if there
- * is data waiting to be transmitted/drained/flushed or not.
- */
-static int dgap_tty_chars_in_buffer(struct tty_struct *tty)
-{
-	struct board_t *bd = NULL;
-	struct channel_t *ch = NULL;
-	struct un_t *un = NULL;
-	struct bs_t *bs = NULL;
-	uchar tbusy;
-	uint chars = 0;
-	u16 thead, ttail, tmask, chead, ctail;
-	ulong   lock_flags = 0;
-	ulong   lock_flags2 = 0;
-
-	if (tty == NULL)
-		return(0);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-
-        bs = ch->ch_bs;
-	if (!bs)
-		return (0);
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	tmask = (ch->ch_tsize - 1);
-
-	/* Get Transmit queue pointers */
-	thead = readw(&(bs->tx_head)) & tmask;
-	ttail = readw(&(bs->tx_tail)) & tmask;
-
-	/* Get tbusy flag */
-	tbusy = readb(&(bs->tbusy));
-
-	/* Get Command queue pointers */
-	chead = readw(&(ch->ch_cm->cm_head));
-	ctail = readw(&(ch->ch_cm->cm_tail));
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	/*
-	 * The only way we know for sure if there is no pending
-	 * data left to be transferred, is if:
-	 * 1) Transmit head and tail are equal (empty).
-	 * 2) Command queue head and tail are equal (empty).
-	 * 3) The "TBUSY" flag is 0. (Transmitter not busy).
- 	 */
-
-	if ((ttail == thead) && (tbusy == 0) && (chead == ctail)) {
-		chars = 0;
-	}
-	else {
-		if (thead >= ttail)
-			chars = thead - ttail;
-		else
-			chars = thead - ttail + ch->ch_tsize;
-		/*
-		 * Fudge factor here.
-		 * If chars is zero, we know that the command queue had
-		 * something in it or tbusy was set.  Because we cannot
-		 * be sure if there is still some data to be transmitted,
-		 * lets lie, and tell ld we have 1 byte left.
-		 */
-		if (chars == 0) {
-			/*
-			 * If TBUSY is still set, and our tx buffers are empty,
-			 * force the firmware to send me another wakeup after
-			 * TBUSY has been cleared.
-			 */
-			if (tbusy != 0) {
-				DGAP_LOCK(ch->ch_lock, lock_flags);
-				un->un_flags |= UN_EMPTY;
-				writeb(1, &(bs->iempty));
-				DGAP_UNLOCK(ch->ch_lock, lock_flags);
-			}
-			chars = 1;
-		}
-	}
-
- 	DPR_WRITE(("dgap_tty_chars_in_buffer. Port: %x - %d (head: %d tail: %d tsize: %d)\n", 
-		ch->ch_portnum, chars, thead, ttail, ch->ch_tsize));
-        return(chars);
-}
-
-
-static int dgap_wait_for_drain(struct tty_struct *tty)
-{
-	struct channel_t *ch;
-	struct un_t *un;
-	struct bs_t *bs;
-	int ret = -EIO;
-	uint count = 1;
-	ulong   lock_flags = 0;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return ret;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return ret;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return ret;
-
-        bs = ch->ch_bs;
-	if (!bs)
-		return ret;
-
-	ret = 0;
-
-	DPR_DRAIN(("dgap_wait_for_drain start\n"));
-
-	/* Loop until data is drained */
-	while (count != 0) {
-
-		count = dgap_tty_chars_in_buffer(tty);
-
-		if (count == 0)
-			break;
-
-		/* Set flag waiting for drain */
-		DGAP_LOCK(ch->ch_lock, lock_flags);
-		un->un_flags |= UN_EMPTY;
-		writeb(1, &(bs->iempty));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-		/* Go to sleep till we get woken up */
-		ret = wait_event_interruptible(un->un_flags_wait, ((un->un_flags & UN_EMPTY) == 0));
-		/* If ret is non-zero, user ctrl-c'ed us */
-		if (ret) {
-			break;
-		}
-	}
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-	un->un_flags &= ~(UN_EMPTY);
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	DPR_DRAIN(("dgap_wait_for_drain finish\n"));
-	return (ret);
-}
-
-
-/*               
- * dgap_maxcps_room
- *
- * Reduces bytes_available to the max number of characters
- * that can be sent currently given the maxcps value, and
- * returns the new bytes_available.  This only affects printer
- * output.
- */                     
-static int dgap_maxcps_room(struct tty_struct *tty, int bytes_available)
-{
-	struct channel_t *ch = NULL;
-	struct un_t *un = NULL;
-
-	if (tty == NULL)
-		return (bytes_available);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (bytes_available);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (bytes_available);
-
-	/*
-	 * If its not the Transparent print device, return
-	 * the full data amount.
-	 */
-	if (un->un_type != DGAP_PRINT)
-		return (bytes_available);
-
-	if (ch->ch_digi.digi_maxcps > 0 && ch->ch_digi.digi_bufsize > 0 ) {
-		int cps_limit = 0;
-		unsigned long current_time = jiffies;
-		unsigned long buffer_time = current_time +
-			(HZ * ch->ch_digi.digi_bufsize) / ch->ch_digi.digi_maxcps;
-
-		if (ch->ch_cpstime < current_time) {
-			/* buffer is empty */
-			ch->ch_cpstime = current_time;            /* reset ch_cpstime */
-			cps_limit = ch->ch_digi.digi_bufsize;
-		}
-		else if (ch->ch_cpstime < buffer_time) {
-			/* still room in the buffer */
-			cps_limit = ((buffer_time - ch->ch_cpstime) * ch->ch_digi.digi_maxcps) / HZ;
-		}
-		else {
-			/* no room in the buffer */
-			cps_limit = 0; 
-		}
-
-		bytes_available = min(cps_limit, bytes_available);
-	}
-
-	return (bytes_available);
-}
-
-
-static inline void dgap_set_firmware_event(struct un_t *un, unsigned int event)
-{
-	struct channel_t *ch = NULL;
-	struct bs_t *bs = NULL;
-
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-        bs = ch->ch_bs;
-	if (!bs)
-		return;
-
-	if ((event & UN_LOW) != 0) {
-		if ((un->un_flags & UN_LOW) == 0) {
-			un->un_flags |= UN_LOW;
-			writeb(1, &(bs->ilow));
-		}
-	}
-	if ((event & UN_LOW) != 0) {
-		if ((un->un_flags & UN_EMPTY) == 0) {
-			un->un_flags |= UN_EMPTY;
-			writeb(1, &(bs->iempty));
-		}
-	}
-}
-
-
-/*
- * dgap_tty_write_room()
- *
- * Return space available in Tx buffer
- */        
-static int dgap_tty_write_room(struct tty_struct *tty)
-{
-	struct channel_t *ch = NULL;
-	struct un_t *un = NULL;
-	struct bs_t *bs = NULL;
-	u16 head, tail, tmask;
-	int ret = 0;
-	ulong   lock_flags = 0;
-
-	if (tty == NULL || dgap_TmpWriteBuf == NULL)
-		return(0);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-
-        bs = ch->ch_bs;
-	if (!bs)
-		return (0);
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	tmask = ch->ch_tsize - 1;
-	head = readw(&(bs->tx_head)) & tmask;
-	tail = readw(&(bs->tx_tail)) & tmask;
-
-        if ((ret = tail - head - 1) < 0)
-                ret += ch->ch_tsize;
-
-	/* Limit printer to maxcps */
-	ret = dgap_maxcps_room(tty, ret);
-
-	/*
-	 * If we are printer device, leave space for 
-	 * possibly both the on and off strings.
-	 */
-	if (un->un_type == DGAP_PRINT) {
-		if (!(ch->ch_flags & CH_PRON))
-			ret -= ch->ch_digi.digi_onlen;
-		ret -= ch->ch_digi.digi_offlen;
-	}
-	else {
-		if (ch->ch_flags & CH_PRON)
-			ret -= ch->ch_digi.digi_offlen;
-	}
-
-	if (ret < 0)
-		ret = 0;
-
-	/*
-	 * Schedule FEP to wake us up if needed.
-	 *
-	 * TODO:  This might be overkill...
-	 * Do we really need to schedule callbacks from the FEP
-	 * in every case?  Can we get smarter based on ret?
-	 */
-	dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
- 
-	DPR_WRITE(("dgap_tty_write_room - %d tail: %d head: %d\n", ret, tail, head));
-
-        return(ret);
-}
-
-
-/*
- * dgap_tty_put_char()
- *
- * Put a character into ch->ch_buf
- *                              
- *      - used by the line discipline for OPOST processing
- */
-static int dgap_tty_put_char(struct tty_struct *tty, unsigned char c)
-{
-	/*
-	 * Simply call tty_write.
-	 */
-	DPR_WRITE(("dgap_tty_put_char called\n"));
-	dgap_tty_write(tty, &c, 1);
-	return 1;
-}
-
-
-/*
- * dgap_tty_write()
- *
- * Take data from the user or kernel and send it out to the FEP.
- * In here exists all the Transparent Print magic as well.
- */
-static int dgap_tty_write(struct tty_struct *tty, const unsigned char *buf, int count)
-{
-	struct channel_t *ch = NULL;
-	struct un_t *un = NULL;
-	struct bs_t *bs = NULL;
-	char *vaddr = NULL;
-	u16 head, tail, tmask, remain;
-	int bufcount = 0, n = 0;
-	int orig_count = 0;
-	ulong lock_flags;
-	int from_user = 0;
-
-	if (tty == NULL || dgap_TmpWriteBuf == NULL)
-		return(0);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return(0);
-
-        bs = ch->ch_bs;
-	if (!bs)
-		return(0);
-
-	if (!count)
-		return(0);
-
-	DPR_WRITE(("dgap_tty_write: Port: %x tty=%p user=%d len=%d\n",
-		ch->ch_portnum, tty, from_user, count));
-
-	/*
-	 * Store original amount of characters passed in.
-	 * This helps to figure out if we should ask the FEP
-	 * to send us an event when it has more space available.
-	 */
-	orig_count = count;
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	/* Get our space available for the channel from the board */
-	tmask = ch->ch_tsize - 1;
-	head = readw(&(bs->tx_head)) & tmask;
-	tail = readw(&(bs->tx_tail)) & tmask;
-
-	if ((bufcount = tail - head - 1) < 0)
-		bufcount += ch->ch_tsize;
-
-	DPR_WRITE(("%d: bufcount: %x count: %x tail: %x head: %x tmask: %x\n",
-		__LINE__, bufcount, count, tail, head, tmask));
-
-	/*
-	 * Limit printer output to maxcps overall, with bursts allowed
-	 * up to bufsize characters.
-	 */
-	bufcount = dgap_maxcps_room(tty, bufcount);
-
-	/*
-	 * Take minimum of what the user wants to send, and the
-	 * space available in the FEP buffer.
-	 */
-	count = min(count, bufcount);
-
-	/*
-	 * Bail if no space left.
-	 */
-	if (count <= 0) {
-		dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-		return(0);
-	}
-
-	/*
-	 * Output the printer ON string, if we are in terminal mode, but
-	 * need to be in printer mode.
-	 */
-	if ((un->un_type == DGAP_PRINT) && !(ch->ch_flags & CH_PRON)) {
-		dgap_wmove(ch, ch->ch_digi.digi_onstr,
-		    (int) ch->ch_digi.digi_onlen);
-		head = readw(&(bs->tx_head)) & tmask;
-		ch->ch_flags |= CH_PRON;
-	}
-
-	/*
-	 * On the other hand, output the printer OFF string, if we are
-	 * currently in printer mode, but need to output to the terminal.
-	 */
-	if ((un->un_type != DGAP_PRINT) && (ch->ch_flags & CH_PRON)) {
-		dgap_wmove(ch, ch->ch_digi.digi_offstr,
-			(int) ch->ch_digi.digi_offlen);
-		head = readw(&(bs->tx_head)) & tmask;
-		ch->ch_flags &= ~CH_PRON;
-	}
-
-	/*
-	 * If there is nothing left to copy, or I can't handle any more data, leave.
-	 */
-	if (count <= 0) {
-		dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-		return(0);
-	}
-
-	if (from_user) {
-
-		count = min(count, WRITEBUFLEN);
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-		/*
-		 * If data is coming from user space, copy it into a temporary
-		 * buffer so we don't get swapped out while doing the copy to
-		 * the board.
-		 */
-		/* we're allowed to block if it's from_user */
-		if (down_interruptible(&dgap_TmpWriteSem)) {
-			return (-EINTR);
-		}
-
-		if (copy_from_user(dgap_TmpWriteBuf, (const uchar __user *) buf, count)) {
-			up(&dgap_TmpWriteSem);
-			printk("Write: Copy from user failed!\n");
-			return -EFAULT;
-		}
-
-		DGAP_LOCK(ch->ch_lock, lock_flags);
-
-		buf = dgap_TmpWriteBuf;
-	}
-
-	n = count;
-
-	/*
-	 * If the write wraps over the top of the circular buffer,
-	 * move the portion up to the wrap point, and reset the
-	 * pointers to the bottom.
-	 */
-	remain = ch->ch_tstart + ch->ch_tsize - head;
-
-	if (n >= remain) {
-		n -= remain;
-		vaddr = ch->ch_taddr + head;
-
-		memcpy_toio(vaddr, (uchar *) buf, remain);
-		dgap_sniff_nowait_nolock(ch, "USER WRITE", (uchar *) buf, remain);
-
-		head = ch->ch_tstart;
-		buf += remain;
-	}
-
-	if (n > 0) {
-
-		/*
-		 * Move rest of data.
-		 */
-		vaddr = ch->ch_taddr + head;
-		remain = n;
-
-		memcpy_toio(vaddr, (uchar *) buf, remain);
-		dgap_sniff_nowait_nolock(ch, "USER WRITE", (uchar *) buf, remain);
-
-		head += remain;
-
-	}
-
-	if (count) {
-		ch->ch_txcount += count;
-		head &= tmask;
-		writew(head, &(bs->tx_head));
-	}
-
-
-	dgap_set_firmware_event(un, UN_LOW | UN_EMPTY);
-
-	/*
-	 * If this is the print device, and the
-	 * printer is still on, we need to turn it
-	 * off before going idle.  If the buffer is
-	 * non-empty, wait until it goes empty.
-	 * Otherwise turn it off right now.
-	 */
-	if ((un->un_type == DGAP_PRINT) && (ch->ch_flags & CH_PRON)) {
-		tail = readw(&(bs->tx_tail)) & tmask;
-
-		if (tail != head) {
-			un->un_flags |= UN_EMPTY;
-			writeb(1, &(bs->iempty));
-		}
-		else {
-			dgap_wmove(ch, ch->ch_digi.digi_offstr,
-				(int) ch->ch_digi.digi_offlen);
-			head = readw(&(bs->tx_head)) & tmask;
-			ch->ch_flags &= ~CH_PRON;
-		}
-	}
-
-	/* Update printer buffer empty time. */
-	if ((un->un_type == DGAP_PRINT) && (ch->ch_digi.digi_maxcps > 0)
-	    && (ch->ch_digi.digi_bufsize > 0)) {
-                ch->ch_cpstime += (HZ * count) / ch->ch_digi.digi_maxcps;
-	}
-
-	if (from_user) {
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-		up(&dgap_TmpWriteSem);
-	} 
-	else {
-		DGAP_UNLOCK(ch->ch_lock, lock_flags);
-	}
-
-	DPR_WRITE(("Write finished - Write %d bytes of %d.\n", count, orig_count));
-
-	return (count);
-}
-
-
-
-/*
- * Return modem signals to ld.
- */
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39)
-static int dgap_tty_tiocmget(struct tty_struct *tty)
-#else
-static int dgap_tty_tiocmget(struct tty_struct *tty, struct file *file)
-#endif
-{
-	struct channel_t *ch;
-	struct un_t *un;
-	int result = -EIO;
-	uchar mstat = 0;
-	ulong lock_flags;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return result;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return result;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return result;
-
-	DPR_IOCTL(("dgap_tty_tiocmget start\n"));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	mstat = readb(&(ch->ch_bs->m_stat));
-        /* Append any outbound signals that might be pending... */
-        mstat |= ch->ch_mostat;
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	result = 0;
-
-	if (mstat & D_DTR(ch))
-		result |= TIOCM_DTR;
-	if (mstat & D_RTS(ch))
-		result |= TIOCM_RTS;
-	if (mstat & D_CTS(ch))
-		result |= TIOCM_CTS;
-	if (mstat & D_DSR(ch))
-		result |= TIOCM_DSR;
-	if (mstat & D_RI(ch))
-		result |= TIOCM_RI;
-	if (mstat & D_CD(ch))
-		result |= TIOCM_CD;
-
-	DPR_IOCTL(("dgap_tty_tiocmget finish\n"));
-
-	return result;
-}
-
-
-/*
- * dgap_tty_tiocmset()
- *
- * Set modem signals, called by ld.
- */
-#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39)
-static int dgap_tty_tiocmset(struct tty_struct *tty,
-                unsigned int set, unsigned int clear)
-#else
-static int dgap_tty_tiocmset(struct tty_struct *tty, struct file *file,
-		unsigned int set, unsigned int clear)
-#endif
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int ret = -EIO;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return ret;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return ret;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return ret;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return ret;
-
-	DPR_IOCTL(("dgap_tty_tiocmset start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	if (set & TIOCM_RTS) {
-		ch->ch_mforce |= D_RTS(ch);
-		ch->ch_mval   |= D_RTS(ch);
-        }         
-
-	if (set & TIOCM_DTR) {
-		ch->ch_mforce |= D_DTR(ch);
-		ch->ch_mval   |= D_DTR(ch);
-        }         
-
-	if (clear & TIOCM_RTS) {
-		ch->ch_mforce |= D_RTS(ch);
-		ch->ch_mval   &= ~(D_RTS(ch));
-        }
-
-	if (clear & TIOCM_DTR) {
-		ch->ch_mforce |= D_DTR(ch);
-		ch->ch_mval   &= ~(D_DTR(ch));
-        }
-
-	dgap_param(tty);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_tiocmset finish\n"));
-
-	return (0);
-}
-
-
-
-/*
- * dgap_tty_send_break()
- *
- * Send a Break, called by ld.
- */
-static int dgap_tty_send_break(struct tty_struct *tty, int msec)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int ret = -EIO;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return ret;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return ret;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return ret;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return ret;
-
-	switch (msec) {
-	case -1:
-		msec = 0xFFFF;
-		break;
-	case 0:
-		msec = 1;
-		break;
-	default:
-		msec /= 10;
-		break;
-	}
-
-	DPR_IOCTL(("dgap_tty_send_break start 1.  %lx\n", jiffies));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-#if 0
-	dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
-#endif
-	dgap_cmdw(ch, SBREAK, (u16) msec, 0);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_send_break finish\n"));
-
-	return (0);
-}
-
-
-
-
-/*
- * dgap_tty_wait_until_sent()
- *
- * wait until data has been transmitted, called by ld.
- */
-static void dgap_tty_wait_until_sent(struct tty_struct *tty, int timeout)
-{
-	int rc;
-	rc = dgap_wait_for_drain(tty);
-	if (rc) {
-		DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-		return;
-	}
-	return;
-}
-
-
-
-/*
- * dgap_send_xchar()
- * 
- * send a high priority character, called by ld.
- */
-static void dgap_tty_send_xchar(struct tty_struct *tty, char c)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_send_xchar start 1.  %lx\n", jiffies));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	/*
-	 * This is technically what we should do.
-	 * However, the NIST tests specifically want
-	 * to see each XON or XOFF character that it
-	 * sends, so lets just send each character
-	 * by hand...
-	 */
-#if 0
-	if (c == STOP_CHAR(tty)) {
-		dgap_cmdw(ch, RPAUSE, 0, 0);
-	}
-	else if (c == START_CHAR(tty)) {
-		dgap_cmdw(ch, RRESUME, 0, 0);
-	}
-	else {
-		dgap_wmove(ch, &c, 1);
-	}
-#else
-	dgap_wmove(ch, &c, 1);
-#endif
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_send_xchar finish\n"));
-
-	return;
-}
-
-
-
-
-/*
- * Return modem signals to ld.
- */
-static int dgap_get_modem_info(struct channel_t *ch, unsigned int __user *value)
-{
-	int result = 0;
-	uchar mstat = 0;
-	ulong lock_flags;
-	int rc = 0;
-
-	DPR_IOCTL(("dgap_get_modem_info start\n"));
-
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return(-ENXIO);
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-
-	mstat = readb(&(ch->ch_bs->m_stat));
-	/* Append any outbound signals that might be pending... */
-	mstat |= ch->ch_mostat;
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	result = 0;
-
-	if (mstat & D_DTR(ch))
-		result |= TIOCM_DTR;
-	if (mstat & D_RTS(ch))
-		result |= TIOCM_RTS;
-	if (mstat & D_CTS(ch))
-		result |= TIOCM_CTS;
-	if (mstat & D_DSR(ch))
-		result |= TIOCM_DSR;
-	if (mstat & D_RI(ch))
-		result |= TIOCM_RI;
-	if (mstat & D_CD(ch))
-		result |= TIOCM_CD;
-
-	rc = put_user(result, value);
-
-	DPR_IOCTL(("dgap_get_modem_info finish\n"));
-	return(rc);
-}
-
-
-/*
- * dgap_set_modem_info()
- *
- * Set modem signals, called by ld.
- */
-static int dgap_set_modem_info(struct tty_struct *tty, unsigned int command, unsigned int __user *value)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int ret = -ENXIO;
-	unsigned int arg = 0;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return ret;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return ret;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return ret;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return ret;
-
-	DPR_IOCTL(("dgap_set_modem_info() start\n"));
-
-	ret = get_user(arg, value);
-	if (ret) {
-		DPR_IOCTL(("dgap_set_modem_info %d ret: %x. finished.\n", __LINE__, ret));
-		return(ret);
-	}
-
-	DPR_IOCTL(("dgap_set_modem_info: command: %x arg: %x\n", command, arg));
-
-	switch (command) {
-	case TIOCMBIS:
-		if (arg & TIOCM_RTS) {
-			ch->ch_mforce |= D_RTS(ch);
-			ch->ch_mval   |= D_RTS(ch);
-        	}
-
-		if (arg & TIOCM_DTR) {
-			ch->ch_mforce |= D_DTR(ch);
-			ch->ch_mval   |= D_DTR(ch);
-        	}
-
-		break;
-
-	case TIOCMBIC:
-		if (arg & TIOCM_RTS) {
-			ch->ch_mforce |= D_RTS(ch);
-			ch->ch_mval   &= ~(D_RTS(ch));
-        	}
-
-		if (arg & TIOCM_DTR) {
-			ch->ch_mforce |= D_DTR(ch);
-			ch->ch_mval   &= ~(D_DTR(ch));
-        	}
-
-		break;
-
-        case TIOCMSET:
-		ch->ch_mforce = D_DTR(ch)|D_RTS(ch);
-
-		if (arg & TIOCM_RTS) {
-			ch->ch_mval |= D_RTS(ch);
-        	}
-		else {
-			ch->ch_mval &= ~(D_RTS(ch));
-		}
-
-		if (arg & TIOCM_DTR) {
-			ch->ch_mval |= (D_DTR(ch));
-        	}
-		else {
-			ch->ch_mval &= ~(D_DTR(ch));
-		}
-
-		break;
-
-	default:
-		return(-EINVAL);
-	}
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	dgap_param(tty);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_set_modem_info finish\n"));
-
-	return (0);
-}
-
-
-/*
- * dgap_tty_digigeta() 
- *
- * Ioctl to get the information for ditty.
- *
- *
- *
- */
-static int dgap_tty_digigeta(struct tty_struct *tty, struct digi_t __user *retinfo)
-{
-	struct channel_t *ch;
-	struct un_t *un;
-	struct digi_t tmp;
-	ulong lock_flags;
-
-	if (!retinfo)
-		return (-EFAULT);
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	memset(&tmp, 0, sizeof(tmp));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-	memcpy(&tmp, &ch->ch_digi, sizeof(tmp));
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return (-EFAULT);
-
-	return (0);
-}
-
-
-/*
- * dgap_tty_digiseta() 
- *
- * Ioctl to set the information for ditty.
- *
- *
- *
- */
-static int dgap_tty_digiseta(struct tty_struct *tty, struct digi_t __user *new_info)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	struct digi_t new_digi;
-	ulong   lock_flags = 0;
-	unsigned long lock_flags2;
-
-	DPR_IOCTL(("DIGI_SETA start\n"));
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (-EFAULT);
-
-        if (copy_from_user(&new_digi, new_info, sizeof(struct digi_t))) {
-		DPR_IOCTL(("DIGI_SETA failed copy_from_user\n"));
-                return(-EFAULT);
-	}
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	memcpy(&ch->ch_digi, &new_digi, sizeof(struct digi_t));
-
-	if (ch->ch_digi.digi_maxcps < 1) 
-		ch->ch_digi.digi_maxcps = 1;
-
-	if (ch->ch_digi.digi_maxcps > 10000) 
-		ch->ch_digi.digi_maxcps = 10000;
-
-	if (ch->ch_digi.digi_bufsize < 10)
-		ch->ch_digi.digi_bufsize = 10;
-
-	if (ch->ch_digi.digi_maxchar < 1)
-		ch->ch_digi.digi_maxchar = 1;
-
-	if (ch->ch_digi.digi_maxchar > ch->ch_digi.digi_bufsize)
-		ch->ch_digi.digi_maxchar = ch->ch_digi.digi_bufsize;
-
-	if (ch->ch_digi.digi_onlen > DIGI_PLEN)
-		ch->ch_digi.digi_onlen = DIGI_PLEN;
-
-	if (ch->ch_digi.digi_offlen > DIGI_PLEN)
-		ch->ch_digi.digi_offlen = DIGI_PLEN;
-
-	dgap_param(tty);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("DIGI_SETA finish\n"));
-
-	return(0);
-}
-
-
-/*
- * dgap_tty_digigetedelay() 
- *
- * Ioctl to get the current edelay setting.
- *
- *
- *
- */
-static int dgap_tty_digigetedelay(struct tty_struct *tty, int __user *retinfo)
-{
-	struct channel_t *ch;
-	struct un_t *un;
-	int tmp;
-	ulong lock_flags;
-
-	if (!retinfo)
-		return (-EFAULT);
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	memset(&tmp, 0, sizeof(tmp));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-	tmp = readw(&(ch->ch_bs->edelay));
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return (-EFAULT);
-
-	return (0);
-}
-
-
-/*
- * dgap_tty_digisetedelay() 
- *
- * Ioctl to set the EDELAY setting
- *
- */
-static int dgap_tty_digisetedelay(struct tty_struct *tty, int __user *new_info)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int new_digi;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	DPR_IOCTL(("DIGI_SETA start\n"));
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (-EFAULT);
-
-        if (copy_from_user(&new_digi, new_info, sizeof(int))) {
-		DPR_IOCTL(("DIGI_SETEDELAY failed copy_from_user\n"));
-                return(-EFAULT);
-	}
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	writew((u16) new_digi, &(ch->ch_bs->edelay));
-
-	dgap_param(tty);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("DIGI_SETA finish\n"));
-
-	return(0);
-}
-
-
-/*
- * dgap_tty_digigetcustombaud()
- *
- * Ioctl to get the current custom baud rate setting.
- */
-static int dgap_tty_digigetcustombaud(struct tty_struct *tty, int __user *retinfo)
-{
-	struct channel_t *ch;
-	struct un_t *un;
-	int tmp;
-	ulong lock_flags;
-
-	if (!retinfo)
-		return (-EFAULT);
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	memset(&tmp, 0, sizeof(tmp));
-
-	DGAP_LOCK(ch->ch_lock, lock_flags);
-	tmp = dgap_get_custom_baud(ch);
-	DGAP_UNLOCK(ch->ch_lock, lock_flags);
-
-	DPR_IOCTL(("DIGI_GETCUSTOMBAUD. Returning %d\n", tmp));
-
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return (-EFAULT);
-
-	return (0);
-}
-
-
-/*
- * dgap_tty_digisetcustombaud() 
- *
- * Ioctl to set the custom baud rate setting
- */
-static int dgap_tty_digisetcustombaud(struct tty_struct *tty, int __user *new_info)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	uint new_rate;
-	ulong lock_flags;
-	ulong lock_flags2;
-
-	DPR_IOCTL(("DIGI_SETCUSTOMBAUD start\n"));
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-EFAULT);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-EFAULT);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-EFAULT);
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (-EFAULT);
-
-
-	if (copy_from_user(&new_rate, new_info, sizeof(unsigned int))) {
-		DPR_IOCTL(("DIGI_SETCUSTOMBAUD failed copy_from_user\n"));
-		return(-EFAULT);
-	}
-
-	if (bd->bd_flags & BD_FEP5PLUS) {
-
-		DPR_IOCTL(("DIGI_SETCUSTOMBAUD. Setting %d\n", new_rate));
-
-		DGAP_LOCK(bd->bd_lock, lock_flags);
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-		ch->ch_custom_speed = new_rate;
-
-		dgap_param(tty);
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-	}
-
-	DPR_IOCTL(("DIGI_SETCUSTOMBAUD finish\n"));
-
-	return(0);
-}
-
-
-/*
- * dgap_set_termios()
- */
-static void dgap_tty_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	unsigned long lock_flags;
-	unsigned long lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	ch->ch_c_cflag   = tty->termios.c_cflag;
-	ch->ch_c_iflag   = tty->termios.c_iflag;
-	ch->ch_c_oflag   = tty->termios.c_oflag;
-	ch->ch_c_lflag   = tty->termios.c_lflag;
-	ch->ch_startc    = tty->termios.c_cc[VSTART];
-	ch->ch_stopc     = tty->termios.c_cc[VSTOP];
-
-	dgap_carrier(ch);
-	dgap_param(tty);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-}
-
-
-static void dgap_tty_throttle(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_throttle start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	ch->ch_flags |= (CH_RXBLOCK);
-#if 1
-	dgap_cmdw(ch, RPAUSE, 0, 0);
-#endif
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_throttle finish\n"));
-}
-
-
-static void dgap_tty_unthrottle(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_unthrottle start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	ch->ch_flags &= ~(CH_RXBLOCK);
-
-#if 1
-	dgap_cmdw(ch, RRESUME, 0, 0);
-#endif
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_unthrottle finish\n"));
-}
-
-
-static void dgap_tty_start(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_start start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	dgap_cmdw(ch, RESUMETX, 0, 0);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_start finish\n"));
-}
-
-
-static void dgap_tty_stop(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_stop start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	dgap_cmdw(ch, PAUSETX, 0, 0);
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_stop finish\n"));
-}
-
-
-/* 
- * dgap_tty_flush_chars()
- *
- * Flush the cook buffer
- *
- * Note to self, and any other poor souls who venture here:
- *
- * flush in this case DOES NOT mean dispose of the data.
- * instead, it means "stop buffering and send it if you
- * haven't already."  Just guess how I figured that out...   SRW 2-Jun-98
- *
- * It is also always called in interrupt context - JAR 8-Sept-99
- */
-static void dgap_tty_flush_chars(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_flush_chars start\n"));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	/* TODO: Do something here */
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-	DPR_IOCTL(("dgap_tty_flush_chars finish\n"));
-}
-
-
-
-/*
- * dgap_tty_flush_buffer()
- *              
- * Flush Tx buffer (make in == out)
- */
-static void dgap_tty_flush_buffer(struct tty_struct *tty)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	ulong   lock_flags;
-	ulong   lock_flags2;
-	u16	head = 0;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return;
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return;
-        
-        ch = un->un_ch;
-        if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-                return;
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return;
-
-	DPR_IOCTL(("dgap_tty_flush_buffer on port: %d start\n", ch->ch_portnum));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	ch->ch_flags &= ~CH_STOP;
-	head = readw(&(ch->ch_bs->tx_head));
-	dgap_cmdw(ch, FLUSHTX, (u16) head, 0);
-	dgap_cmdw(ch, RESUMETX, 0, 0);
-	if (ch->ch_tun.un_flags & (UN_LOW|UN_EMPTY)) {
-		ch->ch_tun.un_flags &= ~(UN_LOW|UN_EMPTY);
-		wake_up_interruptible(&ch->ch_tun.un_flags_wait);
-	}
-	if (ch->ch_pun.un_flags & (UN_LOW|UN_EMPTY)) {
-		ch->ch_pun.un_flags &= ~(UN_LOW|UN_EMPTY);
-		wake_up_interruptible(&ch->ch_pun.un_flags_wait);
-	}
-
-	DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-	DGAP_UNLOCK(bd->bd_lock, lock_flags);
-	if (waitqueue_active(&tty->write_wait))
-		wake_up_interruptible(&tty->write_wait);
-	tty_wakeup(tty);
-
-	DPR_IOCTL(("dgap_tty_flush_buffer finish\n"));
-}
-
-
-
-/*****************************************************************************
- *
- * The IOCTL function and all of its helpers
- *
- *****************************************************************************/
-                        
-/*
- * dgap_tty_ioctl()
- *
- * The usual assortment of ioctl's
- */
-static int dgap_tty_ioctl(struct tty_struct *tty, unsigned int cmd,
-		unsigned long arg)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int rc;
-	u16	head = 0;
-	ulong   lock_flags = 0;
-	ulong   lock_flags2 = 0;
-	void __user *uarg = (void __user *) arg;
-
-	if (!tty || tty->magic != TTY_MAGIC)
-		return (-ENODEV);
-
-	un = tty->driver_data;
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (-ENODEV);
-
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (-ENODEV);
-
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (-ENODEV);
-
-	DPR_IOCTL(("dgap_tty_ioctl start on port %d - cmd %s (%x), arg %lx\n", 
-		ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-	DGAP_LOCK(bd->bd_lock, lock_flags);
-	DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-	if (un->un_open_count <= 0) {
-		DPR_BASIC(("dgap_tty_ioctl - unit not open.\n"));
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(-EIO);
-	}
-
-	switch (cmd) {
-
-	/* Here are all the standard ioctl's that we MUST implement */
-
-	case TCSBRK:
-		/*
-		 * TCSBRK is SVID version: non-zero arg --> no break  
-		 * this behaviour is exploited by tcdrain().
-		 *
-		 * According to POSIX.1 spec (7.2.2.1.2) breaks should be
-		 * between 0.25 and 0.5 seconds so we'll ask for something
-		 * in the middle: 0.375 seconds.
-		 */
-		rc = tty_check_change(tty);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		if (rc) {
-			return(rc);
-		}
-
-		rc = dgap_wait_for_drain(tty);
-
-		if (rc) {
-			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-			return(-EINTR);
-		}
-
-		DGAP_LOCK(bd->bd_lock, lock_flags);
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-		if(((cmd == TCSBRK) && (!arg)) || (cmd == TCSBRKP)) {
-			dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
-		}
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
-			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-                return(0);
-
-
-	case TCSBRKP:
- 		/* support for POSIX tcsendbreak()
-
-		 * According to POSIX.1 spec (7.2.2.1.2) breaks should be
-		 * between 0.25 and 0.5 seconds so we'll ask for something
-		 * in the middle: 0.375 seconds.
-		 */
-		rc = tty_check_change(tty);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		if (rc) {
-			return(rc);
-		}
-
-		rc = dgap_wait_for_drain(tty);
-		if (rc) {
-			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-			return(-EINTR);
-		}
-
-		DGAP_LOCK(bd->bd_lock, lock_flags);
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-		dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
-			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-		return(0);
-
-        case TIOCSBRK:
-		/*
-		 * FEP5 doesn't support turning on a break unconditionally.
-		 * The FEP5 device will stop sending a break automatically
-		 * after the specified time value that was sent when turning on
-		 * the break.
-		 */
-		rc = tty_check_change(tty);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		if (rc) {
-			return(rc);
-		}
-
-		rc = dgap_wait_for_drain(tty);
-		if (rc) {
-			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-			return(-EINTR);
-		}
-
-		DGAP_LOCK(bd->bd_lock, lock_flags);
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-
-		dgap_cmdw(ch, SBREAK, (u16) SBREAK_TIME, 0);
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
-			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-		return 0;
-                
-        case TIOCCBRK:
-		/*
-		 * FEP5 doesn't support turning off a break unconditionally.
-		 * The FEP5 device will stop sending a break automatically
-		 * after the specified time value that was sent when turning on
-		 * the break.
-		 */
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return 0;
-
-	case TIOCGSOFTCAR:
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		rc = put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *) arg);
-		return(rc);
-
-	case TIOCSSOFTCAR:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		rc = get_user(arg, (unsigned long __user *) arg);
-		if (rc)
-			return(rc);
-
-		DGAP_LOCK(bd->bd_lock, lock_flags);
-		DGAP_LOCK(ch->ch_lock, lock_flags2);
-		tty->termios.c_cflag = ((tty->termios.c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
-		dgap_param(tty);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		return(0);
-                        
-	case TIOCMGET:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-                return(dgap_get_modem_info(ch, uarg));
-
-	case TIOCMBIS:
-	case TIOCMBIC:
-	case TIOCMSET:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_set_modem_info(tty, cmd, uarg));
-
-		/*
-		 * Here are any additional ioctl's that we want to implement
-		 */
-                        
-	case TCFLSH:  
-		/*
-		 * The linux tty driver doesn't have a flush
-		 * input routine for the driver, assuming all backed
-		 * up data is in the line disc. buffers.  However,
-		 * we all know that's not the case.  Here, we
-		 * act on the ioctl, but then lie and say we didn't
-		 * so the line discipline will process the flush
-		 * also.
-		 */   
-		rc = tty_check_change(tty);
-		if (rc) {
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			return(rc);
-		}
-
-		if ((arg == TCIFLUSH) || (arg == TCIOFLUSH)) {
-			if (!(un->un_type == DGAP_PRINT)) {
-				head = readw(&(ch->ch_bs->rx_head));
-				writew(head, &(ch->ch_bs->rx_tail));
-				writeb(0, &(ch->ch_bs->orun));
-			}
-		}
-
-		if ((arg == TCOFLUSH) || (arg == TCIOFLUSH)) {
-			ch->ch_flags &= ~CH_STOP;
-			head = readw(&(ch->ch_bs->tx_head));
-			dgap_cmdw(ch, FLUSHTX, (u16) head, 0 );
-			dgap_cmdw(ch, RESUMETX, 0, 0);
-			if (ch->ch_tun.un_flags & (UN_LOW|UN_EMPTY)) {
-				ch->ch_tun.un_flags &= ~(UN_LOW|UN_EMPTY);
-				wake_up_interruptible(&ch->ch_tun.un_flags_wait);
-			}
-			if (ch->ch_pun.un_flags & (UN_LOW|UN_EMPTY)) {
-				ch->ch_pun.un_flags &= ~(UN_LOW|UN_EMPTY);
-				wake_up_interruptible(&ch->ch_pun.un_flags_wait);
-			}
-			if (waitqueue_active(&tty->write_wait))
-				wake_up_interruptible(&tty->write_wait);
-
-			/* Can't hold any locks when calling tty_wakeup! */
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			tty_wakeup(tty);
-			DGAP_LOCK(bd->bd_lock, lock_flags);
-			DGAP_LOCK(ch->ch_lock, lock_flags2);
-		}                  
-
-		/* pretend we didn't recognize this IOCTL */  
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		DPR_IOCTL(("dgap_tty_ioctl (LINE:%d) finish on port %d - cmd %s (%x), arg %lx\n", 
-			__LINE__, ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-		return(-ENOIOCTLCMD);
-
-	case TCSETSF:
-	case TCSETSW:
-		/*
-		 * The linux tty driver doesn't have a flush
-		 * input routine for the driver, assuming all backed
-		 * up data is in the line disc. buffers.  However,
-		 * we all know that's not the case.  Here, we
-		 * act on the ioctl, but then lie and say we didn't
-		 * so the line discipline will process the flush
-		 * also.
-		 */
-		if (cmd == TCSETSF) {
-			/* flush rx */
-			ch->ch_flags &= ~CH_STOP;
-			head = readw(&(ch->ch_bs->rx_head));
-			writew(head, &(ch->ch_bs->rx_tail));
-		}
-
-		/* now wait for all the output to drain */
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		rc = dgap_wait_for_drain(tty);
-		if (rc) {
-			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-			return(-EINTR);
-		}
-
-		DPR_IOCTL(("dgap_tty_ioctl finish on port %d - cmd %s (%x), arg %lx\n", 
-			ch->ch_portnum, dgap_ioctl_name(cmd), cmd, arg));
-
-		/* pretend we didn't recognize this */
-		return(-ENOIOCTLCMD);
-
-	case TCSETAW:
-
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		rc = dgap_wait_for_drain(tty);
-		if (rc) {
-			DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-			return(-EINTR);
-		}
-
-		/* pretend we didn't recognize this */
-		return(-ENOIOCTLCMD);  
-
-	case TCXONC:
-		/*
-		 * The Linux Line Discipline (LD) would do this for us if we
-		 * let it, but we have the special firmware options to do this
-		 * the "right way" regardless of hardware or software flow
-		 * control so we'll do it outselves instead of letting the LD
-		 * do it.
-		 */
-		rc = tty_check_change(tty);
-		if (rc) {
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			return(rc);
-		}
-
-		DPR_IOCTL(("dgap_ioctl - in TCXONC - %d\n", cmd));
-		switch (arg) {
-
-		case TCOON:
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			dgap_tty_start(tty);
-			return(0);
-		case TCOOFF:
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			dgap_tty_stop(tty);
-			return(0);
-		case TCION:
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			/* Make the ld do it */
-			return(-ENOIOCTLCMD);
-		case TCIOFF:
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			/* Make the ld do it */
-			return(-ENOIOCTLCMD);
-		default:
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			return(-EINVAL);
-		}
-
-	case DIGI_GETA:
-		/* get information for ditty */
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digigeta(tty, uarg));
-
-	case DIGI_SETAW:
-	case DIGI_SETAF:
-
-		/* set information for ditty */
-		if (cmd == (DIGI_SETAW)) {
-
-			DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-			DGAP_UNLOCK(bd->bd_lock, lock_flags);
-			rc = dgap_wait_for_drain(tty);
-			if (rc) {
-				DPR_IOCTL(("dgap_tty_ioctl - bad return: %d ", rc));
-				return(-EINTR);
-			}
-			DGAP_LOCK(bd->bd_lock, lock_flags);
-			DGAP_LOCK(ch->ch_lock, lock_flags2);
-		}
-		else {
-			tty_ldisc_flush(tty);
-		}
-		/* fall thru */
-
-	case DIGI_SETA:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digiseta(tty, uarg));
-
-	case DIGI_GEDELAY:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digigetedelay(tty, uarg));
-
-	case DIGI_SEDELAY:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digisetedelay(tty, uarg));
-
-	case DIGI_GETCUSTOMBAUD:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digigetcustombaud(tty, uarg));
-
-	case DIGI_SETCUSTOMBAUD:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return(dgap_tty_digisetcustombaud(tty, uarg));
-
-	case DIGI_RESET_PORT:
-		dgap_firmware_reset_port(ch);
-		dgap_param(tty);
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-		return 0;
-
-	default:
-		DGAP_UNLOCK(ch->ch_lock, lock_flags2);
-		DGAP_UNLOCK(bd->bd_lock, lock_flags);
-
-		DPR_IOCTL(("dgap_tty_ioctl - in default\n"));
-		DPR_IOCTL(("dgap_tty_ioctl end - cmd %s (%x), arg %lx\n", 
-			dgap_ioctl_name(cmd), cmd, arg));
-
-		return(-ENOIOCTLCMD);
-	}
-}
-static ssize_t dgap_driver_version_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%s\n", DG_PART);
-}
-static DRIVER_ATTR(version, S_IRUSR, dgap_driver_version_show, NULL);
-
-
-static ssize_t dgap_driver_boards_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%d\n", dgap_NumBoards);
-}
-static DRIVER_ATTR(boards, S_IRUSR, dgap_driver_boards_show, NULL);
-
-
-static ssize_t dgap_driver_maxboards_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%d\n", MAXBOARDS);
-}
-static DRIVER_ATTR(maxboards, S_IRUSR, dgap_driver_maxboards_show, NULL);
-
-
-static ssize_t dgap_driver_pollcounter_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%ld\n", dgap_poll_counter);
-}
-static DRIVER_ATTR(pollcounter, S_IRUSR, dgap_driver_pollcounter_show, NULL);
-
-
-static ssize_t dgap_driver_state_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%s\n", dgap_driver_state_text[dgap_driver_state]);
-}
-static DRIVER_ATTR(state, S_IRUSR, dgap_driver_state_show, NULL);
-
-
-static ssize_t dgap_driver_debug_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "0x%x\n", dgap_debug);
-}
-
-static ssize_t dgap_driver_debug_store(struct device_driver *ddp, const char *buf, size_t count)
-{
-	sscanf(buf, "0x%x\n", &dgap_debug);
-	return count;
-}
-static DRIVER_ATTR(debug, (S_IRUSR | S_IWUSR), dgap_driver_debug_show, dgap_driver_debug_store);
-
-
-static ssize_t dgap_driver_rawreadok_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "0x%x\n", dgap_rawreadok);
-}
-
-static ssize_t dgap_driver_rawreadok_store(struct device_driver *ddp, const char *buf, size_t count)
-{
-	sscanf(buf, "0x%x\n", &dgap_rawreadok);
-	return count;
-}
-static DRIVER_ATTR(rawreadok, (S_IRUSR | S_IWUSR), dgap_driver_rawreadok_show, dgap_driver_rawreadok_store);
-
-
-static ssize_t dgap_driver_pollrate_show(struct device_driver *ddp, char *buf)
-{
-	return snprintf(buf, PAGE_SIZE, "%dms\n", dgap_poll_tick);
-}
-
-static ssize_t dgap_driver_pollrate_store(struct device_driver *ddp, const char *buf, size_t count)
-{
-	sscanf(buf, "%d\n", &dgap_poll_tick);
-	return count;
-}
-static DRIVER_ATTR(pollrate, (S_IRUSR | S_IWUSR), dgap_driver_pollrate_show, dgap_driver_pollrate_store);
-
-
-static void dgap_create_driver_sysfiles(struct pci_driver *dgap_driver)
-{
-	int rc = 0;
-	struct device_driver *driverfs = &dgap_driver->driver;
-
-	rc |= driver_create_file(driverfs, &driver_attr_version);
-	rc |= driver_create_file(driverfs, &driver_attr_boards);
-	rc |= driver_create_file(driverfs, &driver_attr_maxboards);
-	rc |= driver_create_file(driverfs, &driver_attr_debug);
-	rc |= driver_create_file(driverfs, &driver_attr_rawreadok); 
-	rc |= driver_create_file(driverfs, &driver_attr_pollrate);
-	rc |= driver_create_file(driverfs, &driver_attr_pollcounter);
-	rc |= driver_create_file(driverfs, &driver_attr_state);
-	if (rc) {
-		printk(KERN_ERR "DGAP: sysfs driver_create_file failed!\n");
-	}
-}
-
-
-static void dgap_remove_driver_sysfiles(struct pci_driver *dgap_driver)
-{
-	struct device_driver *driverfs = &dgap_driver->driver;
-	driver_remove_file(driverfs, &driver_attr_version);
-	driver_remove_file(driverfs, &driver_attr_boards);
-	driver_remove_file(driverfs, &driver_attr_maxboards);
-	driver_remove_file(driverfs, &driver_attr_debug);
-	driver_remove_file(driverfs, &driver_attr_rawreadok);
-	driver_remove_file(driverfs, &driver_attr_pollrate);
-	driver_remove_file(driverfs, &driver_attr_pollcounter);
-	driver_remove_file(driverfs, &driver_attr_state);
-}
-
-
-#define DGAP_VERIFY_BOARD(p, bd)			\
-	if (!p)						\
-		return (0);				\
-							\
-	bd = dev_get_drvdata(p);			\
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)	\
-		return (0);				\
-	if (bd->state != BOARD_READY)			\
-		return (0);				\
-
-
-static ssize_t dgap_ports_state_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count,
-			"%d %s\n", bd->channels[i]->ch_portnum,
-			bd->channels[i]->ch_open_count ? "Open" : "Closed");
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_state, S_IRUSR, dgap_ports_state_show, NULL);
-
-
-static ssize_t dgap_ports_baud_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count +=  snprintf(buf + count, PAGE_SIZE - count,
-			"%d %d\n", bd->channels[i]->ch_portnum, bd->channels[i]->ch_baud_info);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_baud, S_IRUSR, dgap_ports_baud_show, NULL);
-
-
-static ssize_t dgap_ports_msignals_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		if (bd->channels[i]->ch_open_count) {
-			count += snprintf(buf + count, PAGE_SIZE - count,
-				"%d %s %s %s %s %s %s\n", bd->channels[i]->ch_portnum,
-				(bd->channels[i]->ch_mostat & UART_MCR_RTS) ? "RTS" : "",
-				(bd->channels[i]->ch_mistat & UART_MSR_CTS) ? "CTS" : "",
-				(bd->channels[i]->ch_mostat & UART_MCR_DTR) ? "DTR" : "",
-				(bd->channels[i]->ch_mistat & UART_MSR_DSR) ? "DSR" : "",
-				(bd->channels[i]->ch_mistat & UART_MSR_DCD) ? "DCD" : "",
-				(bd->channels[i]->ch_mistat & UART_MSR_RI)  ? "RI"  : "");
-		} else {
-			count += snprintf(buf + count, PAGE_SIZE - count,
-				"%d\n", bd->channels[i]->ch_portnum);
-		}
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_msignals, S_IRUSR, dgap_ports_msignals_show, NULL);
-
-
-static ssize_t dgap_ports_iflag_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_iflag);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_iflag, S_IRUSR, dgap_ports_iflag_show, NULL);
-
-
-static ssize_t dgap_ports_cflag_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_cflag);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_cflag, S_IRUSR, dgap_ports_cflag_show, NULL);
-
-
-static ssize_t dgap_ports_oflag_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_oflag);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_oflag, S_IRUSR, dgap_ports_oflag_show, NULL);
-
-
-static ssize_t dgap_ports_lflag_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_c_lflag);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_lflag, S_IRUSR, dgap_ports_lflag_show, NULL);
-
-
-static ssize_t dgap_ports_digi_flag_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %x\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_digi.digi_flags);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_digi_flag, S_IRUSR, dgap_ports_digi_flag_show, NULL);
-
-
-static ssize_t dgap_ports_rxcount_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %ld\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_rxcount);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_rxcount, S_IRUSR, dgap_ports_rxcount_show, NULL);
-
-
-static ssize_t dgap_ports_txcount_show(struct device *p, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	int count = 0;
-	int i = 0;
-
-	DGAP_VERIFY_BOARD(p, bd);
-
-	for (i = 0; i < bd->nasync; i++) {
-		count += snprintf(buf + count, PAGE_SIZE - count, "%d %ld\n",
-			bd->channels[i]->ch_portnum, bd->channels[i]->ch_txcount);
-	}
-	return count;
-}
-static DEVICE_ATTR(ports_txcount, S_IRUSR, dgap_ports_txcount_show, NULL);
-
-
-/* this function creates the sys files that will export each signal status
- * to sysfs each value will be put in a separate filename
- */
-static void dgap_create_ports_sysfiles(struct board_t *bd)
-{
-	int rc = 0;
-
-	dev_set_drvdata(&bd->pdev->dev, bd);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_state);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_baud);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_msignals);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_iflag);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_cflag);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_oflag);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_lflag);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_digi_flag);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_rxcount);
-	rc |= device_create_file(&(bd->pdev->dev), &dev_attr_ports_txcount);
-	if (rc) {
-		printk(KERN_ERR "DGAP: sysfs device_create_file failed!\n");
-	}
-}
-
-
-/* removes all the sys files created for that port */
-static void dgap_remove_ports_sysfiles(struct board_t *bd)
-{
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_state);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_baud);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_msignals);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_iflag);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_cflag);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_oflag);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_lflag);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_digi_flag);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_rxcount);
-	device_remove_file(&(bd->pdev->dev), &dev_attr_ports_txcount);
-}
-
-
-static ssize_t dgap_tty_state_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%s", un->un_open_count ? "Open" : "Closed");
-}
-static DEVICE_ATTR(state, S_IRUSR, dgap_tty_state_show, NULL);
-
-
-static ssize_t dgap_tty_baud_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%d\n", ch->ch_baud_info);
-}
-static DEVICE_ATTR(baud, S_IRUSR, dgap_tty_baud_show, NULL);
-
-
-static ssize_t dgap_tty_msignals_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	if (ch->ch_open_count) {
-		return snprintf(buf, PAGE_SIZE, "%s %s %s %s %s %s\n",
-			(ch->ch_mostat & UART_MCR_RTS) ? "RTS" : "",
-			(ch->ch_mistat & UART_MSR_CTS) ? "CTS" : "",
-			(ch->ch_mostat & UART_MCR_DTR) ? "DTR" : "",
-			(ch->ch_mistat & UART_MSR_DSR) ? "DSR" : "",
-			(ch->ch_mistat & UART_MSR_DCD) ? "DCD" : "",
-			(ch->ch_mistat & UART_MSR_RI)  ? "RI"  : "");
-	}
-	return 0;
-}
-static DEVICE_ATTR(msignals, S_IRUSR, dgap_tty_msignals_show, NULL);
-
-
-static ssize_t dgap_tty_iflag_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_iflag);
-}
-static DEVICE_ATTR(iflag, S_IRUSR, dgap_tty_iflag_show, NULL);
-
-
-static ssize_t dgap_tty_cflag_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_cflag);
-}
-static DEVICE_ATTR(cflag, S_IRUSR, dgap_tty_cflag_show, NULL);
-
-
-static ssize_t dgap_tty_oflag_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_oflag);
-}
-static DEVICE_ATTR(oflag, S_IRUSR, dgap_tty_oflag_show, NULL);
-
-
-static ssize_t dgap_tty_lflag_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_c_lflag);
-}
-static DEVICE_ATTR(lflag, S_IRUSR, dgap_tty_lflag_show, NULL);
-
-
-static ssize_t dgap_tty_digi_flag_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%x\n", ch->ch_digi.digi_flags);
-}
-static DEVICE_ATTR(digi_flag, S_IRUSR, dgap_tty_digi_flag_show, NULL);
-
-
-static ssize_t dgap_tty_rxcount_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%ld\n", ch->ch_rxcount);
-}
-static DEVICE_ATTR(rxcount, S_IRUSR, dgap_tty_rxcount_show, NULL);
-
-
-static ssize_t dgap_tty_txcount_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-	return snprintf(buf, PAGE_SIZE, "%ld\n", ch->ch_txcount);
-}
-static DEVICE_ATTR(txcount, S_IRUSR, dgap_tty_txcount_show, NULL);
-
-
-static ssize_t dgap_tty_name_show(struct device *d, struct device_attribute *attr, char *buf)
-{
-	struct board_t *bd;
-	struct channel_t *ch;
-	struct un_t *un;
-	int	cn;
-	int	bn;
-	struct cnode *cptr = NULL;
-	int found = FALSE;
-	int ncount = 0;
-	int starto = 0;
-	int i = 0;
-
-	if (!d)
-		return (0);
-	un = dev_get_drvdata(d);
-	if (!un || un->magic != DGAP_UNIT_MAGIC)
-		return (0);
-	ch = un->un_ch;
-	if (!ch || ch->magic != DGAP_CHANNEL_MAGIC)
-		return (0);
-	bd = ch->ch_bd;
-	if (!bd || bd->magic != DGAP_BOARD_MAGIC)
-		return (0);
-	if (bd->state != BOARD_READY)
-		return (0);
-
-        bn = bd->boardnum;
-	cn = ch->ch_portnum;
-
-	for (cptr = bd->bd_config; cptr; cptr = cptr->next) {
-
-		if ((cptr->type == BNODE) &&
-		    ((cptr->u.board.type == APORT2_920P) || (cptr->u.board.type == APORT4_920P) ||
-		     (cptr->u.board.type == APORT8_920P) || (cptr->u.board.type == PAPORT4) ||
-		     (cptr->u.board.type == PAPORT8))) {
-
-				found = TRUE;
-				if (cptr->u.board.v_start)
-					starto = cptr->u.board.start;
-				else
-					starto = 1;
-		}
-
-		if (cptr->type == TNODE && found == TRUE) {
-			char *ptr1;
-			if (strstr(cptr->u.ttyname, "tty")) {
-				ptr1 = cptr->u.ttyname;
-				ptr1 += 3;
-			}
-			else {
-				ptr1 = cptr->u.ttyname;
-			}
-
-			for (i = 0; i < dgap_config_get_number_of_ports(bd); i++) {
-				if (cn == i) {
-					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
-						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
-						ptr1, i + starto);
-				}
-			}
-		}
-
-		if (cptr->type == CNODE) {
-
-			for (i = 0; i < cptr->u.conc.nport; i++) {
-				if (cn == (i + ncount)) {
-
-					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
-						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
-						cptr->u.conc.id,
-						i + (cptr->u.conc.v_start ? cptr->u.conc.start : 1));
-				}
-			}
-
-			ncount += cptr->u.conc.nport;
-		}
-
-		if (cptr->type == MNODE) {
-
-			for (i = 0; i < cptr->u.module.nport; i++) {
-				if (cn == (i + ncount)) {
-					return snprintf(buf, PAGE_SIZE, "%s%s%02d\n",
-						(un->un_type == DGAP_PRINT) ? "pr" : "tty",
-						cptr->u.module.id,
-						i + (cptr->u.module.v_start ? cptr->u.module.start : 1));
-				}
-			}
-
-			ncount += cptr->u.module.nport;
-
-		}
-	}
-
-	return snprintf(buf, PAGE_SIZE, "%s_dgap_%d_%d\n",
-		(un->un_type == DGAP_PRINT) ? "pr" : "tty", bn, cn);
-
-}
-static DEVICE_ATTR(custom_name, S_IRUSR, dgap_tty_name_show, NULL);
-
-
-static struct attribute *dgap_sysfs_tty_entries[] = {
-	&dev_attr_state.attr,
-	&dev_attr_baud.attr,
-	&dev_attr_msignals.attr,
-	&dev_attr_iflag.attr,
-	&dev_attr_cflag.attr,
-	&dev_attr_oflag.attr,
-	&dev_attr_lflag.attr,
-	&dev_attr_digi_flag.attr,
-	&dev_attr_rxcount.attr,
-	&dev_attr_txcount.attr,
-	&dev_attr_custom_name.attr,
-	NULL
-};
-
-
-static struct attribute_group dgap_tty_attribute_group = {
-	.name = NULL,
-	.attrs = dgap_sysfs_tty_entries,
-};
-
-
-
-
-static void dgap_create_tty_sysfs(struct un_t *un, struct device *c)
-{
-	int ret;
-
-	ret = sysfs_create_group(&c->kobj, &dgap_tty_attribute_group);
-	if (ret) {
-		printk(KERN_ERR "dgap: failed to create sysfs tty device attributes.\n");
-		sysfs_remove_group(&c->kobj, &dgap_tty_attribute_group);
-		return;
-	}
-
-	dev_set_drvdata(c, un);
-
-}
-
-
-static void dgap_remove_tty_sysfs(struct device *c)
-{
-	sysfs_remove_group(&c->kobj, &dgap_tty_attribute_group);
-}
diff -urpN linux-3.13.1-orig/drivers/staging/dgap/dgap_driver.h linux-3.13.1-new/drivers/staging/dgap/dgap_driver.h
--- linux-3.13.1-orig/drivers/staging/dgap/dgap_driver.h	2014-02-11 10:17:49.137517346 -0500
+++ linux-3.13.1-new/drivers/staging/dgap/dgap_driver.h	1969-12-31 19:00:00.000000000 -0500
@@ -1,1566 +0,0 @@
-/*
- * Copyright 2003 Digi International (www.digi.com)
- *      Scott H Kilau <Scott_Kilau at digi dot com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
- * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
- * PURPOSE.  See the GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- *	NOTE: THIS IS A SHARED HEADER. DO NOT CHANGE CODING STYLE!!!
- *
- *************************************************************************
- *
- * Driver includes
- *
- *************************************************************************/
-
-#ifndef __DGAP_DRIVER_H
-#define __DGAP_DRIVER_H
-
-#include <linux/version.h>	/* To get the current Linux version */
-#include <linux/types.h>        /* To pick up the varions Linux types */
-#include <linux/tty.h>          /* To pick up the various tty structs/defines */
-#include <linux/interrupt.h>    /* For irqreturn_t type */
-
-#if !defined(TTY_FLIPBUF_SIZE)
-# define TTY_FLIPBUF_SIZE 512
-#endif
-
-#define PARM_INT(VAR, INIT, PERM, DESC) \
-		static int VAR = INIT; \
-		int dgap_##VAR; \
-		module_param(VAR, int, PERM); \
-		MODULE_PARM_DESC(VAR, DESC);
-
-/*************************************************************************
- *
- * Driver defines
- *
- *************************************************************************/
-
-/*
- * Driver identification, error and debugging statments
- *
- * In theory, you can change all occurrences of "digi" in the next
- * three lines, and the driver printk's will all automagically change.
- *
- * APR((fmt, args, ...));	Always prints message
- * DPR((fmt, args, ...));	Only prints if DGAP_TRACER is defined at
- *				  compile time and dgap_debug!=0
- */
-#define	DG_NAME		"dgap-1.3-16"
-#define	DG_PART		"40002347_C"
-
-#define	PROCSTR		"dgap"			/* /proc entries	 */
-#define	DEVSTR		"/dev/dg/dgap"		/* /dev entries		 */
-#define	DRVSTR		"dgap"			/* Driver name string 
-						 * displayed by APR	 */
-#define	APR(args)	do { PRINTF_TO_KMEM(args); printk(DRVSTR": "); printk args; \
-			   } while (0)
-#define	RAPR(args)	do { PRINTF_TO_KMEM(args); printk args; } while (0)
-
-#define TRC_TO_CONSOLE 1
-
-#ifndef TRUE
-# define TRUE 1
-#endif
-
-#ifndef FALSE
-# define FALSE 0
-#endif
-
-/* Required for our shared headers! */
-typedef unsigned char           uchar;
-
-/************************************************************************
- * Stuff from dgap_pci.h
- ************************************************************************/
-#define PCIMAX 32			/* maximum number of PCI boards */
-
-#define DIGI_VID		0x114F
-
-#define PCI_DEVICE_EPC_DID	0x0002
-#define PCI_DEVICE_XEM_DID	0x0004
-#define PCI_DEVICE_XR_DID	0x0005
-#define PCI_DEVICE_CX_DID	0x0006
-#define PCI_DEVICE_XRJ_DID	0x0009	/* PLX-based Xr adapter */
-#define PCI_DEVICE_XR_IBM_DID	0x0011	/* IBM 8-port Async Adapter */
-#define PCI_DEVICE_XR_BULL_DID	0x0013	/* BULL 8-port Async Adapter */
-#define PCI_DEVICE_XR_SAIP_DID	0x001c	/* SAIP card - Xr adapter */
-#define PCI_DEVICE_XR_422_DID	0x0012	/* Xr-422 */
-#define PCI_DEVICE_920_2_DID	0x0034	/* XR-Plus 920 K, 2 port */
-#define PCI_DEVICE_920_4_DID	0x0026	/* XR-Plus 920 K, 4 port */
-#define PCI_DEVICE_920_8_DID	0x0027	/* XR-Plus 920 K, 8 port */
-#define PCI_DEVICE_EPCJ_DID	0x000a	/* PLX 9060 chip for PCI  */
-#define PCI_DEVICE_CX_IBM_DID	0x001b	/* IBM 128-port Async Adapter */
-#define PCI_DEVICE_920_8_HP_DID	0x0058	/* HP XR-Plus 920 K, 8 port */
-#define PCI_DEVICE_XEM_HP_DID	0x0059  /* HP Xem PCI */
-
-#define PCI_DEVICE_XEM_NAME	"AccelePort XEM"
-#define PCI_DEVICE_CX_NAME	"AccelePort CX"
-#define PCI_DEVICE_XR_NAME	"AccelePort Xr"
-#define PCI_DEVICE_XRJ_NAME	"AccelePort Xr (PLX)"
-#define PCI_DEVICE_XR_SAIP_NAME	"AccelePort Xr (SAIP)"
-#define PCI_DEVICE_920_2_NAME	"AccelePort Xr920 2 port"
-#define PCI_DEVICE_920_4_NAME	"AccelePort Xr920 4 port"
-#define PCI_DEVICE_920_8_NAME	"AccelePort Xr920 8 port"
-#define PCI_DEVICE_XR_422_NAME	"AccelePort Xr 422"
-#define PCI_DEVICE_EPCJ_NAME	"AccelePort EPC (PLX)"
-#define PCI_DEVICE_XR_BULL_NAME	"AccelePort Xr (BULL)"
-#define PCI_DEVICE_XR_IBM_NAME	"AccelePort Xr (IBM)"
-#define PCI_DEVICE_CX_IBM_NAME	"AccelePort CX (IBM)"
-#define PCI_DEVICE_920_8_HP_NAME "AccelePort Xr920 8 port (HP)"
-#define PCI_DEVICE_XEM_HP_NAME	"AccelePort XEM (HP)"
-
-
-/*
- * On the PCI boards, there is no IO space allocated
- * The I/O registers will be in the first 3 bytes of the
- * upper 2MB of the 4MB memory space.  The board memory
- * will be mapped into the low 2MB of the 4MB memory space
- */
-
-/* Potential location of PCI Bios from E0000 to FFFFF*/
-#define PCI_BIOS_SIZE		0x00020000
-
-/* Size of Memory and I/O for PCI (4MB) */
-#define PCI_RAM_SIZE		0x00400000
-
-/* Size of Memory (2MB) */
-#define PCI_MEM_SIZE		0x00200000
-
-/* Max PCI Window Size (2MB) */
-#define PCI_WIN_SIZE		0x00200000
-
-#define PCI_WIN_SHIFT		21 /* 21 bits max */
-
-/* Offset of I/0 in Memory (2MB) */
-#define PCI_IO_OFFSET		0x00200000
-
-/* Size of IO (2MB) */
-#define PCI_IO_SIZE		0x00200000
-
-/************************************************************************
- ***	Definitions for Digi ditty(1) command.
- ************************************************************************/
-
-
-/*
- * Copyright (c) 1988-96 Digi International Inc., All Rights Reserved.
- */
-
-/************************************************************************
- * This module provides application access to special Digi
- * serial line enhancements which are not standard UNIX(tm) features.
- ************************************************************************/
-
-#if !defined(TIOCMODG)
-
-#define	TIOCMODG	('d'<<8) | 250		/* get modem ctrl state	*/
-#define	TIOCMODS	('d'<<8) | 251		/* set modem ctrl state	*/
-
-#ifndef TIOCM_LE 
-#define		TIOCM_LE	0x01		/* line enable		*/
-#define		TIOCM_DTR	0x02		/* data terminal ready	*/
-#define		TIOCM_RTS	0x04		/* request to send	*/
-#define		TIOCM_ST	0x08		/* secondary transmit	*/
-#define		TIOCM_SR	0x10		/* secondary receive	*/
-#define		TIOCM_CTS	0x20		/* clear to send	*/
-#define		TIOCM_CAR	0x40		/* carrier detect	*/
-#define		TIOCM_RNG	0x80		/* ring	indicator	*/
-#define		TIOCM_DSR	0x100		/* data set ready	*/
-#define		TIOCM_RI	TIOCM_RNG	/* ring (alternate)	*/
-#define		TIOCM_CD	TIOCM_CAR	/* carrier detect (alt)	*/
-#endif
-
-#endif
-
-#if !defined(TIOCMSET)
-#define	TIOCMSET	('d'<<8) | 252		/* set modem ctrl state	*/
-#define	TIOCMGET	('d'<<8) | 253		/* set modem ctrl state	*/
-#endif
-
-#if !defined(TIOCMBIC)
-#define	TIOCMBIC	('d'<<8) | 254		/* set modem ctrl state */
-#define	TIOCMBIS	('d'<<8) | 255		/* set modem ctrl state */
-#endif
-
-
-#if !defined(TIOCSDTR)
-#define	TIOCSDTR	('e'<<8) | 0		/* set DTR		*/
-#define	TIOCCDTR	('e'<<8) | 1		/* clear DTR		*/
-#endif
-
-/************************************************************************
- * Ioctl command arguments for DIGI parameters.
- ************************************************************************/
-#define DIGI_GETA	('e'<<8) | 94		/* Read params		*/
-
-#define DIGI_SETA	('e'<<8) | 95		/* Set params		*/
-#define DIGI_SETAW	('e'<<8) | 96		/* Drain & set params	*/
-#define DIGI_SETAF	('e'<<8) | 97		/* Drain, flush & set params */
-
-#define DIGI_KME	('e'<<8) | 98		/* Read/Write Host	*/
-						/* Adapter Memory	*/
-
-#define	DIGI_GETFLOW	('e'<<8) | 99		/* Get startc/stopc flow */
-						/* control characters 	 */
-#define	DIGI_SETFLOW	('e'<<8) | 100		/* Set startc/stopc flow */
-						/* control characters	 */
-#define	DIGI_GETAFLOW	('e'<<8) | 101		/* Get Aux. startc/stopc */
-						/* flow control chars 	 */
-#define	DIGI_SETAFLOW	('e'<<8) | 102		/* Set Aux. startc/stopc */
-						/* flow control chars	 */
-
-#define DIGI_GEDELAY	('d'<<8) | 246		/* Get edelay */
-#define DIGI_SEDELAY	('d'<<8) | 247		/* Set edelay */
-
-struct	digiflow_t {
-	unsigned char	startc;				/* flow cntl start char	*/
-	unsigned char	stopc;				/* flow cntl stop char	*/
-};
-
-
-#ifdef	FLOW_2200
-#define	F2200_GETA	('e'<<8) | 104		/* Get 2x36 flow cntl flags */
-#define	F2200_SETAW	('e'<<8) | 105		/* Set 2x36 flow cntl flags */
-#define		F2200_MASK	0x03		/* 2200 flow cntl bit mask  */
-#define		FCNTL_2200	0x01		/* 2x36 terminal flow cntl  */
-#define		PCNTL_2200	0x02		/* 2x36 printer flow cntl   */
-#define	F2200_XON	0xf8
-#define	P2200_XON	0xf9
-#define	F2200_XOFF	0xfa
-#define	P2200_XOFF	0xfb
-
-#define	FXOFF_MASK	0x03			/* 2200 flow status mask    */
-#define	RCVD_FXOFF	0x01			/* 2x36 Terminal XOFF rcvd  */
-#define	RCVD_PXOFF	0x02			/* 2x36 Printer XOFF rcvd   */
-#endif
-
-/************************************************************************
- * Values for digi_flags 
- ************************************************************************/
-#define DIGI_IXON	0x0001		/* Handle IXON in the FEP	*/
-#define DIGI_FAST	0x0002		/* Fast baud rates		*/
-#define RTSPACE		0x0004		/* RTS input flow control	*/
-#define CTSPACE		0x0008		/* CTS output flow control	*/
-#define DSRPACE		0x0010		/* DSR output flow control	*/
-#define DCDPACE		0x0020		/* DCD output flow control	*/
-#define DTRPACE		0x0040		/* DTR input flow control	*/
-#define DIGI_COOK	0x0080		/* Cooked processing done in FEP */
-#define DIGI_FORCEDCD	0x0100		/* Force carrier		*/
-#define	DIGI_ALTPIN	0x0200		/* Alternate RJ-45 pin config	*/
-#define	DIGI_AIXON	0x0400		/* Aux flow control in fep	*/
-#define	DIGI_PRINTER	0x0800		/* Hold port open for flow cntrl*/
-#define DIGI_PP_INPUT	0x1000		/* Change parallel port to input*/
-#define DIGI_DTR_TOGGLE 0x2000		/* Support DTR Toggle		*/
-#define	DIGI_422	0x4000		/* for 422/232 selectable panel */
-#define DIGI_RTS_TOGGLE	0x8000		/* Support RTS Toggle		*/
-
-/************************************************************************
- * These options are not supported on the comxi.
- ************************************************************************/
-#define	DIGI_COMXI	(DIGI_FAST|DIGI_COOK|DSRPACE|DCDPACE|DTRPACE)
-
-#define DIGI_PLEN	28		/* String length		*/
-#define	DIGI_TSIZ	10		/* Terminal string len		*/
-
-/************************************************************************
- * Structure used with ioctl commands for DIGI parameters.
- ************************************************************************/
-struct digi_t {
-	unsigned short	digi_flags;		/* Flags (see above)	*/
-	unsigned short	digi_maxcps;		/* Max printer CPS	*/
-	unsigned short	digi_maxchar;		/* Max chars in print queue */
-	unsigned short	digi_bufsize;		/* Buffer size		*/
-	unsigned char	digi_onlen;		/* Length of ON string	*/
-	unsigned char	digi_offlen;		/* Length of OFF string	*/
-	char		digi_onstr[DIGI_PLEN];	/* Printer on string	*/
-	char		digi_offstr[DIGI_PLEN];	/* Printer off string	*/
-	char		digi_term[DIGI_TSIZ];	/* terminal string	*/
-};
-
-/************************************************************************
- * KME definitions and structures.
- ************************************************************************/
-#define	RW_IDLE		0	/* Operation complete			*/
-#define	RW_READ		1	/* Read Concentrator Memory		*/
-#define	RW_WRITE	2	/* Write Concentrator Memory		*/
-
-struct rw_t {
-	unsigned char	rw_req;		/* Request type			*/
-	unsigned char	rw_board;	/* Host Adapter board number	*/
-	unsigned char	rw_conc;	/* Concentrator number		*/
-	unsigned char	rw_reserved;	/* Reserved for expansion	*/
-	unsigned long	rw_addr;	/* Address in concentrator	*/
-	unsigned short	rw_size;	/* Read/write request length	*/
-	unsigned char	rw_data[128];	/* Data to read/write		*/
-};
-
-/***********************************************************************
- * Shrink Buffer and Board Information definitions and structures.
-
- ************************************************************************/
-			/* Board type return codes */
-#define	PCXI_TYPE 1     /* Board type at the designated port is a PC/Xi */
-#define PCXM_TYPE 2     /* Board type at the designated port is a PC/Xm */
-#define	PCXE_TYPE 3     /* Board type at the designated port is a PC/Xe */
-#define	MCXI_TYPE 4     /* Board type at the designated port is a MC/Xi */
-#define COMXI_TYPE 5     /* Board type at the designated port is a COM/Xi */
-
-			 /* Non-Zero Result codes. */
-#define RESULT_NOBDFND 1 /* A Digi product at that port is not config installed */ 
-#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */ 
-#define RESULT_NOOSSIG 3 /* FEP/OS signature was not detected on the board */
-#define RESULT_TOOSML  4 /* Too small an area to shrink.  */
-#define RESULT_NOCHAN  5 /* Channel structure for the board was not found */
-
-struct shrink_buf_struct {
-	unsigned long	shrink_buf_vaddr;	/* Virtual address of board */
-	unsigned long	shrink_buf_phys;	/* Physical address of board */
-	unsigned long	shrink_buf_bseg;	/* Amount of board memory */
-	unsigned long	shrink_buf_hseg;	/* '186 Beginning of Dual-Port */
-
-	unsigned long	shrink_buf_lseg;	/* '186 Beginning of freed memory						*/ 
-	unsigned long	shrink_buf_mseg;	/* Linear address from start of
-						   dual-port were freed memory
-						   begins, host viewpoint. */
-
-	unsigned long	shrink_buf_bdparam;	/* Parameter for xxmemon and
-						   xxmemoff */
-
-	unsigned long	shrink_buf_reserva;	/* Reserved */
-	unsigned long	shrink_buf_reservb;	/* Reserved */
-	unsigned long	shrink_buf_reservc;	/* Reserved */
-	unsigned long	shrink_buf_reservd;	/* Reserved */
-
-	unsigned char	shrink_buf_result;	/* Reason for call failing
-						   Zero is Good return */
-	unsigned char	shrink_buf_init;	/* Non-Zero if it caused an     
-						   xxinit call. */
-
-	unsigned char	shrink_buf_anports;	/* Number of async ports  */
-	unsigned char	shrink_buf_snports; 	/* Number of sync  ports */
-	unsigned char	shrink_buf_type;	/* Board type 1 = PC/Xi,
-							      2 = PC/Xm,
-							      3 = PC/Xe  
-							      4 = MC/Xi  
-							      5 = COMX/i */
-	unsigned char	shrink_buf_card;	/* Card number */
-	
-};
-
-/************************************************************************
- * Structure to get driver status information
- ************************************************************************/
-struct digi_dinfo {
-	unsigned long	dinfo_nboards;		/* # boards configured	*/
-	char		dinfo_reserved[12];	/* for future expansion */
-	char		dinfo_version[16];	/* driver version       */
-};
-
-#define	DIGI_GETDD	('d'<<8) | 248		/* get driver info      */
- 
-/************************************************************************
- * Structure used with ioctl commands for per-board information
- *
- * physsize and memsize differ when board has "windowed" memory
- ************************************************************************/
-struct digi_info {
-	unsigned long	info_bdnum;		/* Board number (0 based)  */
-	unsigned long	info_ioport;		/* io port address         */
-	unsigned long	info_physaddr;		/* memory address          */
-	unsigned long	info_physsize;		/* Size of host mem window */
-	unsigned long	info_memsize;		/* Amount of dual-port mem */
-						/* on board                */
-	unsigned short	info_bdtype;		/* Board type              */
-	unsigned short	info_nports;		/* number of ports         */
-	char		info_bdstate;		/* board state             */
-	char		info_reserved[7];	/* for future expansion    */
-};
-
-#define	DIGI_GETBD	('d'<<8) | 249		/* get board info          */
- 
-struct digi_stat {
-	unsigned int	info_chan;		/* Channel number (0 based)  */
-	unsigned int	info_brd;		/* Board number (0 based)  */
-	unsigned long	info_cflag;		/* cflag for channel       */
-	unsigned long	info_iflag;		/* iflag for channel       */
-	unsigned long	info_oflag;		/* oflag for channel       */
-	unsigned long	info_mstat;		/* mstat for channel       */
-	unsigned long	info_tx_data;		/* tx_data for channel       */
-	unsigned long	info_rx_data;		/* rx_data for channel       */
-	unsigned long	info_hflow;		/* hflow for channel       */
-	unsigned long	info_reserved[8];	/* for future expansion    */
-};
-
-#define	DIGI_GETSTAT	('d'<<8) | 244		/* get board info          */
-/************************************************************************
- *
- * Structure used with ioctl commands for per-channel information
- *
- ************************************************************************/
-struct digi_ch {
-	unsigned long	info_bdnum;		/* Board number (0 based)  */
-	unsigned long	info_channel;		/* Channel index number    */
-	unsigned long	info_ch_cflag;		/* Channel cflag   	   */
-	unsigned long	info_ch_iflag;		/* Channel iflag   	   */
-	unsigned long	info_ch_oflag;		/* Channel oflag   	   */
-	unsigned long	info_chsize;		/* Channel structure size  */
-	unsigned long	info_sleep_stat;	/* sleep status		   */
-	dev_t		info_dev;		/* device number	   */
-	unsigned char	info_initstate;		/* Channel init state	   */
-	unsigned char	info_running;		/* Channel running state   */
-	long		reserved[8];		/* reserved for future use */
-};
-
-/*
-* This structure is used with the DIGI_FEPCMD ioctl to 
-* tell the driver which port to send the command for.
-*/
-struct digi_cmd {
-	int	cmd;
-	int	word;
-	int	ncmds;
-	int	chan; /* channel index (zero based) */
-	int	bdid; /* board index (zero based) */
-};
-
-/*
-*  info_sleep_stat defines
-*/
-#define INFO_RUNWAIT	0x0001
-#define INFO_WOPEN	0x0002
-#define INFO_TTIOW	0x0004
-#define INFO_CH_RWAIT	0x0008
-#define INFO_CH_WEMPTY	0x0010
-#define INFO_CH_WLOW	0x0020
-#define INFO_XXBUF_BUSY 0x0040
-
-#define	DIGI_GETCH	('d'<<8) | 245		/* get board info          */
-
-/* Board type definitions */
-
-#define	SUBTYPE		0007
-#define	T_PCXI		0000
-#define T_PCXM		0001
-#define T_PCXE		0002
-#define T_PCXR		0003
-#define T_SP		0004
-#define T_SP_PLUS	0005
-#	define T_HERC	0000
-#	define T_HOU	0001
-#	define T_LON	0002
-#	define T_CHA	0003
-#define FAMILY		0070
-#define T_COMXI		0000
-#define T_PCXX		0010
-#define T_CX		0020
-#define T_EPC		0030
-#define	T_PCLITE	0040
-#define	T_SPXX		0050
-#define	T_AVXX		0060
-#define T_DXB		0070
-#define T_A2K_4_8	0070
-#define BUSTYPE		0700
-#define T_ISABUS	0000
-#define T_MCBUS		0100
-#define	T_EISABUS	0200
-#define	T_PCIBUS	0400
-
-/* Board State Definitions */
-
-#define	BD_RUNNING	0x0
-#define	BD_REASON	0x7f
-#define	BD_NOTFOUND	0x1
-#define	BD_NOIOPORT	0x2
-#define	BD_NOMEM	0x3
-#define	BD_NOBIOS	0x4
-#define	BD_NOFEP	0x5
-#define	BD_FAILED	0x6
-#define BD_ALLOCATED	0x7
-#define BD_TRIBOOT	0x8
-#define	BD_BADKME	0x80
-
-#define DIGI_LOOPBACK	      ('d'<<8) | 252		/* Enable/disable UART internal loopback */
-#define DIGI_SPOLL            ('d'<<8) | 254		/* change poller rate   */
-
-#define DIGI_SETCUSTOMBAUD	_IOW('e', 106, int)	/* Set integer baud rate */
-#define DIGI_GETCUSTOMBAUD	_IOR('e', 107, int)	/* Get integer baud rate */
-#define DIGI_RESET_PORT		('e'<<8) | 93		/* Reset port		*/
-
-
-/*
- * Debugging levels can be set using debug insmod variable
- * They can also be compiled out completely.
- */
-
-#define	DBG_INIT		(dgap_debug & 0x01)
-#define	DBG_BASIC		(dgap_debug & 0x02)
-#define	DBG_CORE		(dgap_debug & 0x04)
-
-#define	DBG_OPEN		(dgap_debug & 0x08)
-#define	DBG_CLOSE		(dgap_debug & 0x10)
-#define	DBG_READ		(dgap_debug & 0x20)
-#define	DBG_WRITE		(dgap_debug & 0x40)
-
-#define	DBG_IOCTL		(dgap_debug & 0x80)
-
-#define	DBG_PROC		(dgap_debug & 0x100)
-#define	DBG_PARAM		(dgap_debug & 0x200)
-#define	DBG_PSCAN		(dgap_debug & 0x400)
-#define	DBG_EVENT		(dgap_debug & 0x800)
-
-#define	DBG_DRAIN		(dgap_debug & 0x1000)
-#define	DBG_CARR		(dgap_debug & 0x2000)
-
-#define	DBG_MGMT		(dgap_debug & 0x4000)
-
-
-#if defined(DGAP_TRACER)
-
-# if defined(TRC_TO_KMEM)
-/* Choose one: */
-#  define TRC_ON_OVERFLOW_WRAP_AROUND
-#  undef  TRC_ON_OVERFLOW_SHIFT_BUFFER
-# endif //TRC_TO_KMEM
-
-# define TRC_MAXMSG		1024
-# define TRC_OVERFLOW		"(OVERFLOW)"
-# define TRC_DTRC		"/usr/bin/dtrc"
-
-#if defined TRC_TO_CONSOLE
-#define PRINTF_TO_CONSOLE(args) { printk(DRVSTR": "); printk args; }
-#else //!defined TRACE_TO_CONSOLE
-#define PRINTF_TO_CONSOLE(args)
-#endif
-
-#if defined TRC_TO_KMEM
-#define PRINTF_TO_KMEM(args) dgap_tracef args 
-#else //!defined TRC_TO_KMEM
-#define PRINTF_TO_KMEM(args)
-#endif
-
-#define	TRC(args)	{ PRINTF_TO_KMEM(args); PRINTF_TO_CONSOLE(args) }
-
-# define DPR_INIT(ARGS)		if (DBG_INIT) TRC(ARGS)
-# define DPR_BASIC(ARGS)	if (DBG_BASIC) TRC(ARGS)
-# define DPR_CORE(ARGS)		if (DBG_CORE) TRC(ARGS)
-# define DPR_OPEN(ARGS)		if (DBG_OPEN)  TRC(ARGS)
-# define DPR_CLOSE(ARGS)	if (DBG_CLOSE)  TRC(ARGS)
-# define DPR_READ(ARGS)		if (DBG_READ)  TRC(ARGS)
-# define DPR_WRITE(ARGS)	if (DBG_WRITE) TRC(ARGS)
-# define DPR_IOCTL(ARGS)	if (DBG_IOCTL) TRC(ARGS)
-# define DPR_PROC(ARGS)		if (DBG_PROC)  TRC(ARGS)
-# define DPR_PARAM(ARGS)	if (DBG_PARAM)  TRC(ARGS)
-# define DPR_PSCAN(ARGS)	if (DBG_PSCAN)  TRC(ARGS)
-# define DPR_EVENT(ARGS)	if (DBG_EVENT)  TRC(ARGS)
-# define DPR_DRAIN(ARGS)	if (DBG_DRAIN)  TRC(ARGS)
-# define DPR_CARR(ARGS)		if (DBG_CARR)  TRC(ARGS)
-# define DPR_MGMT(ARGS)		if (DBG_MGMT)  TRC(ARGS)
-
-# define DPR(ARGS)		if (dgap_debug) TRC(ARGS)
-# define P(X)			dgap_tracef(#X "=%p\n", X)
-# define X(X)			dgap_tracef(#X "=%x\n", X)
-
-#else//!defined DGAP_TRACER
-
-#define PRINTF_TO_KMEM(args)
-# define TRC(ARGS)
-# define DPR_INIT(ARGS)
-# define DPR_BASIC(ARGS)
-# define DPR_CORE(ARGS)
-# define DPR_OPEN(ARGS)
-# define DPR_CLOSE(ARGS)
-# define DPR_READ(ARGS)
-# define DPR_WRITE(ARGS)
-# define DPR_IOCTL(ARGS)
-# define DPR_PROC(ARGS)
-# define DPR_PARAM(ARGS)
-# define DPR_PSCAN(ARGS)
-# define DPR_EVENT(ARGS)
-# define DPR_DRAIN(ARGS)
-# define DPR_CARR(ARGS)
-# define DPR_MGMT(ARGS)
-
-# define DPR(args)
-
-#endif//DGAP_TRACER
-
-/* Number of boards we support at once. */
-#define	MAXBOARDS	32
-#define	MAXPORTS	224
-#define MAXTTYNAMELEN	200
-
-/* Our 3 magic numbers for our board, channel and unit structs */
-#define DGAP_BOARD_MAGIC	0x5c6df104
-#define DGAP_CHANNEL_MAGIC	0x6c6df104
-#define DGAP_UNIT_MAGIC		0x7c6df104
-
-/* Serial port types */
-#define DGAP_SERIAL		0
-#define DGAP_PRINT		1
-
-#define	SERIAL_TYPE_NORMAL	1
-
-/* 4 extra for alignment play space */
-#define WRITEBUFLEN		((4096) + 4)
-#define MYFLIPLEN		N_TTY_BUF_SIZE
-
-#define SBREAK_TIME 0x25
-#define U2BSIZE 0x400
-
-#define dgap_jiffies_from_ms(a) (((a) * HZ) / 1000)
-
-/*
- * Our major for the mgmt devices.
- *
- * We can use 22, because Digi was allocated 22 and 23 for the epca driver.
- * 22 has now become obsolete now that the "cu" devices have 
- * been removed from 2.6.
- * Also, this *IS* the epca driver, just PCI only now.
- */
-#ifndef DIGI_DGAP_MAJOR
-# define DIGI_DGAP_MAJOR         22
-#endif
-
-/*
- * The parameters we use to define the periods of the moving averages.
- */
-#define		MA_PERIOD	(HZ / 10)
-#define		SMA_DUR		(1 * HZ)
-#define		EMA_DUR		(1 * HZ)
-#define		SMA_NPERIODS	(SMA_DUR / MA_PERIOD)
-#define		EMA_NPERIODS	(EMA_DUR / MA_PERIOD)
-
-/*
- * Define a local default termios struct. All ports will be created
- * with this termios initially.  This is the same structure that is defined
- * as the default in tty_io.c with the same settings overriden as in serial.c
- *
- * In short, this should match the internal serial ports' defaults.
- */
-#define	DEFAULT_IFLAGS	(ICRNL | IXON)
-#define	DEFAULT_OFLAGS	(OPOST | ONLCR)
-#define	DEFAULT_CFLAGS	(B9600 | CS8 | CREAD | HUPCL | CLOCAL)
-#define	DEFAULT_LFLAGS	(ISIG | ICANON | ECHO | ECHOE | ECHOK | \
-			ECHOCTL | ECHOKE | IEXTEN)
-
-#ifndef _POSIX_VDISABLE
-#define   _POSIX_VDISABLE '\0'
-#endif
-
-#define SNIFF_MAX	65536		/* Sniff buffer size (2^n) */
-#define SNIFF_MASK	(SNIFF_MAX - 1)	/* Sniff wrap mask */
-
-#define VPDSIZE (512)
-
-/*
- * Lock function/defines.
- * Makes spotting lock/unlock locations easier.
- */
-# define DGAP_SPINLOCK_INIT(x)		spin_lock_init(&(x))
-# define DGAP_LOCK(x,y)			spin_lock_irqsave(&(x), y)
-# define DGAP_UNLOCK(x,y)		spin_unlock_irqrestore(&(x), y)
-# define DGAP_TRYLOCK(x,y)		spin_trylock(&(x))
-
-/*
- * All the possible states the driver can be while being loaded.
- */
-enum {
-	DRIVER_INITIALIZED = 0,
-	DRIVER_NEED_CONFIG_LOAD,
-	DRIVER_REQUESTED_CONFIG,
-	DRIVER_READY
-};
-
-/*
- * All the possible states the board can be while booting up.
- */
-enum {
-	BOARD_FAILED = 0,
-	CONFIG_NOT_FOUND,
-	BOARD_FOUND,
-	NEED_RESET,
-	FINISHED_RESET,
-	NEED_CONFIG,
-	FINISHED_CONFIG,
-	NEED_DEVICE_CREATION,
-	REQUESTED_DEVICE_CREATION,
-	FINISHED_DEVICE_CREATION,
-	NEED_BIOS_LOAD,
-	REQUESTED_BIOS,
-	WAIT_BIOS_LOAD,
-	FINISHED_BIOS_LOAD,
-	NEED_FEP_LOAD,
-	REQUESTED_FEP,
-	WAIT_FEP_LOAD,
-	FINISHED_FEP_LOAD,
-	NEED_PROC_CREATION,
-	FINISHED_PROC_CREATION,
-	BOARD_READY
-};
-
-/*
- * All the possible states that a requested concentrator image can be in.
- */
-enum {
-	NO_PENDING_CONCENTRATOR_REQUESTS = 0,
-	NEED_CONCENTRATOR,
-	REQUESTED_CONCENTRATOR
-};
-
-extern char *dgap_state_text[];
-extern char *dgap_driver_state_text[];
-
-
-/* 
- * Modem line constants are defined as macros because DSR and
- * DCD are swapable using the ditty altpin option.
- */
-#define D_CD(ch)        ch->ch_cd       /* Carrier detect       */
-#define D_DSR(ch)       ch->ch_dsr      /* Data set ready       */
-#define D_RTS(ch)       DM_RTS          /* Request to send      */
-#define D_CTS(ch)       DM_CTS          /* Clear to send        */
-#define D_RI(ch)        DM_RI           /* Ring indicator       */
-#define D_DTR(ch)       DM_DTR          /* Data terminal ready  */
-
-
-/*************************************************************************
- *
- * Structures and closely related defines.
- *
- *************************************************************************/
-
-
-/*
- * A structure to hold a statistics counter.  We also
- * compute moving averages for this counter.
- */
-struct macounter
-{
-	u32		cnt;	/* Total count */
-	ulong		accum;	/* Acuumulator per period */
-	ulong		sma;	/* Simple moving average */
-	ulong		ema;	/* Exponential moving average */
-};
-
-
-/************************************************************************ 
- * Device flag definitions for bd_flags.
- ************************************************************************/
-#define	BD_FEP5PLUS	0x0001          /* Supports FEP5 Plus commands */
-#define BD_HAS_VPD	0x0002		/* Board has VPD info available */
-
-
-/*
- *	Per-board information
- */
-struct board_t
-{
-	int		magic;		/* Board Magic number.  */
-	int		boardnum;	/* Board number: 0-3 */
-	int		firstminor;	/* First minor, e.g. 0, 30, 60 */
-
-	int		type;		/* Type of board */
-	char		*name;		/* Product Name */
-	struct pci_dev	*pdev;		/* Pointer to the pci_dev struct */ 
-	u16		vendor;		/* PCI vendor ID */
-	u16		device;		/* PCI device ID */
-	u16		subvendor;	/* PCI subsystem vendor ID */
-	u16		subdevice;	/* PCI subsystem device ID */
-	uchar		rev;		/* PCI revision ID */
-	uint		pci_bus;	/* PCI bus value */
-	uint		pci_slot;	/* PCI slot value */
-	u16		maxports;	/* MAX ports this board can handle */
-	uchar		vpd[VPDSIZE];	/* VPD of board, if found */
-	u32		bd_flags;	/* Board flags */
-
-	spinlock_t	bd_lock;	/* Used to protect board */
-
-	u32		state;		/* State of card. */
-	wait_queue_head_t state_wait;	/* Place to sleep on for state change */
-
-	struct		tasklet_struct helper_tasklet; /* Poll helper tasklet */
-
-	u32		wait_for_bios;
-	u32		wait_for_fep;
-
-	struct cnode *  bd_config;	/* Config of board */
-
-	u16		nasync;		/* Number of ports on card */
-
-	u32		use_interrupts;	/* Should we be interrupt driven? */
-	ulong		irq;		/* Interrupt request number */
-	ulong		intr_count;	/* Count of interrupts */
-	u32		intr_used;	/* Non-zero if using interrupts */
-	u32		intr_running;	/* Non-zero if FEP knows its doing interrupts */
-
-	ulong		port;		/* Start of base io port of the card */
-	ulong		port_end;	/* End of base io port of the card */
-	ulong		membase;	/* Start of base memory of the card */
-	ulong		membase_end;	/* End of base memory of the card */
-
-	uchar 		*re_map_port;	/* Remapped io port of the card */
-	uchar		*re_map_membase;/* Remapped memory of the card */
-
-	uchar		runwait;	/* # Processes waiting for FEP  */
-	uchar		inhibit_poller; /* Tells  the poller to leave us alone */
-
-	struct channel_t *channels[MAXPORTS]; /* array of pointers to our channels. */
-
-	struct tty_driver	*SerialDriver;
-	char		SerialName[200];
-	struct tty_driver	*PrintDriver;
-	char		PrintName[200];
-
-	u32		dgap_Major_Serial_Registered;
-	u32		dgap_Major_TransparentPrint_Registered;
-
-	u32		dgap_Serial_Major;
-	u32		dgap_TransparentPrint_Major;
-
-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
-	u32		TtyRefCnt;
-#endif
-
-	struct bs_t	*bd_bs;			/* Base structure pointer       */
-
-	char	*flipbuf;		/* Our flip buffer, alloced if board is found */
-	char	*flipflagbuf;		/* Our flip flag buffer, alloced if board is found */
-
-	u16		dpatype;	/* The board "type", as defined by DPA */
-	u16		dpastatus;	/* The board "status", as defined by DPA */
-	wait_queue_head_t kme_wait;	/* Needed for DPA support */
-
-	u32		conc_dl_status;	/* Status of any pending conc download */
-	/*
-	 *	Mgmt data.
-	 */
-        char		*msgbuf_head;
-        char		*msgbuf;
-};
-
-
-
-/************************************************************************ 
- * Unit flag definitions for un_flags.
- ************************************************************************/
-#define UN_ISOPEN	0x0001		/* Device is open		*/
-#define UN_CLOSING	0x0002		/* Line is being closed		*/
-#define UN_IMM		0x0004		/* Service immediately		*/
-#define UN_BUSY		0x0008		/* Some work this channel	*/
-#define UN_BREAKI	0x0010		/* Input break received		*/
-#define UN_PWAIT	0x0020		/* Printer waiting for terminal	*/
-#define UN_TIME		0x0040		/* Waiting on time		*/
-#define UN_EMPTY	0x0080		/* Waiting output queue empty	*/
-#define UN_LOW		0x0100		/* Waiting output low water mark*/
-#define UN_EXCL_OPEN	0x0200		/* Open for exclusive use	*/
-#define UN_WOPEN	0x0400		/* Device waiting for open	*/
-#define UN_WIOCTL	0x0800		/* Device waiting for open	*/
-#define UN_HANGUP	0x8000		/* Carrier lost			*/
-
-struct device;
-
-/************************************************************************
- * Structure for terminal or printer unit. 
- ************************************************************************/
-struct un_t {
-	int	magic;		/* Unit Magic Number.			*/
-	struct	channel_t *un_ch;
-	u32	un_time;
-	u32	un_type;
-	u32	un_open_count;	/* Counter of opens to port		*/
-	struct tty_struct *un_tty;/* Pointer to unit tty structure	*/
-	u32	un_flags;	/* Unit flags				*/
-	wait_queue_head_t un_flags_wait; /* Place to sleep to wait on unit */
-	u32	un_dev;		/* Minor device number			*/
-	tcflag_t un_oflag;	/* oflags being done on board		*/
-	tcflag_t un_lflag;	/* lflags being done on board		*/
-	struct device *un_sysfs;
-};
-
-
-/************************************************************************ 
- * Device flag definitions for ch_flags.
- ************************************************************************/
-#define CH_PRON         0x0001          /* Printer on string                */
-#define CH_OUT          0x0002          /* Dial-out device open             */
-#define CH_STOP         0x0004          /* Output is stopped                */
-#define CH_STOPI        0x0008          /* Input is stopped                 */
-#define CH_CD           0x0010          /* Carrier is present               */
-#define CH_FCAR         0x0020          /* Carrier forced on                */
-
-#define CH_RXBLOCK      0x0080          /* Enable rx blocked flag           */
-#define CH_WLOW         0x0100          /* Term waiting low event           */
-#define CH_WEMPTY       0x0200          /* Term waiting empty event         */
-#define CH_RENABLE      0x0400          /* Buffer just emptied          */
-#define CH_RACTIVE      0x0800          /* Process active in xxread()   */
-#define CH_RWAIT        0x1000          /* Process waiting in xxread()  */
-#define CH_BAUD0	0x2000		/* Used for checking B0 transitions */
-#define CH_HANGUP       0x8000		/* Hangup received                  */
-
-/*
- * Definitions for ch_sniff_flags
- */
-#define SNIFF_OPEN	0x1
-#define SNIFF_WAIT_DATA	0x2
-#define SNIFF_WAIT_SPACE 0x4
-
-
-/************************************************************************ 
- * Channel information structure.
- ************************************************************************/
-struct channel_t {
-	int magic;			/* Channel Magic Number		*/
-	struct bs_t	*ch_bs;		/* Base structure pointer       */
-	struct cm_t	*ch_cm;		/* Command queue pointer        */
-	struct board_t *ch_bd;		/* Board structure pointer      */
-	unsigned char *ch_vaddr;	/* FEP memory origin            */
-	unsigned char *ch_taddr;	/* Write buffer origin          */
-	unsigned char *ch_raddr;	/* Read buffer origin           */
-	struct digi_t  ch_digi;		/* Transparent Print structure  */
-	struct un_t ch_tun;		/* Terminal unit info           */
-	struct un_t ch_pun;		/* Printer unit info            */
-
-	spinlock_t	ch_lock;	/* provide for serialization */
-	wait_queue_head_t ch_flags_wait;
-
-	u32	pscan_state;
-	uchar	pscan_savechar;
-
-	u32 ch_portnum;			/* Port number, 0 offset.	*/
-	u32 ch_open_count;		/* open count			*/
-	u32	ch_flags;		/* Channel flags                */
-
-
-	u32	ch_close_delay;		/* How long we should drop RTS/DTR for */
-
-	u32	ch_cpstime;		/* Time for CPS calculations    */
-
-	tcflag_t ch_c_iflag;		/* channel iflags               */
-	tcflag_t ch_c_cflag;		/* channel cflags               */
-	tcflag_t ch_c_oflag;		/* channel oflags               */
-	tcflag_t ch_c_lflag;		/* channel lflags               */
-
-	u16  ch_fepiflag;            /* FEP tty iflags               */
-	u16  ch_fepcflag;		/* FEP tty cflags               */
-	u16  ch_fepoflag;		/* FEP tty oflags               */
-	u16  ch_wopen;			/* Waiting for open process cnt */
-	u16  ch_tstart;			/* Transmit buffer start        */
-	u16  ch_tsize;			/* Transmit buffer size         */
-	u16  ch_rstart;			/* Receive buffer start         */
-	u16  ch_rsize;			/* Receive buffer size          */
-	u16  ch_rdelay;			/* Receive delay time           */
-
-	u16	ch_tlw;			/* Our currently set low water mark */
-
-	u16  ch_cook;			/* Output character mask        */
-
-	uchar   ch_card;		/* Card channel is on           */
-	uchar   ch_stopc;		/* Stop character               */
-	uchar   ch_startc;		/* Start character              */
-
-	uchar   ch_mostat;		/* FEP output modem status      */
-	uchar   ch_mistat;		/* FEP input modem status       */
-	uchar   ch_mforce;		/* Modem values to be forced    */
-	uchar   ch_mval;		/* Force values                 */
-	uchar   ch_fepstopc;		/* FEP stop character           */
-	uchar   ch_fepstartc;		/* FEP start character          */
-
-	uchar   ch_astopc;		/* Auxiliary Stop character     */
-	uchar   ch_astartc;		/* Auxiliary Start character    */
-	uchar   ch_fepastopc;		/* Auxiliary FEP stop char      */
-	uchar   ch_fepastartc;		/* Auxiliary FEP start char     */
-
-	uchar   ch_hflow;		/* FEP hardware handshake       */
-	uchar   ch_dsr;			/* stores real dsr value        */
-	uchar   ch_cd;			/* stores real cd value         */
-	uchar   ch_tx_win;		/* channel tx buffer window     */
-	uchar   ch_rx_win;		/* channel rx buffer window     */
-	uint	ch_custom_speed;	/* Custom baud, if set		*/
-	uint	ch_baud_info;		/* Current baud info for /proc output	*/
-	ulong	ch_rxcount;		/* total of data received so far	*/
-	ulong	ch_txcount;		/* total of data transmitted so far	*/
-	ulong	ch_err_parity;		/* Count of parity errors on channel	*/
-	ulong	ch_err_frame;		/* Count of framing errors on channel	*/
-	ulong	ch_err_break;		/* Count of breaks on channel	*/
-	ulong	ch_err_overrun;		/* Count of overruns on channel	*/
-
-	uint ch_sniff_in;
-	uint ch_sniff_out;
-	char *ch_sniff_buf;		/* Sniff buffer for proc */
-	ulong ch_sniff_flags;		/* Channel flags                */
-	wait_queue_head_t ch_sniff_wait;
-};
-
-
-/*************************************************************************
- *
- * Prototypes for non-static functions used in more than one module
- *
- *************************************************************************/
-
-extern int		dgap_ms_sleep(ulong ms);
-extern void		*dgap_driver_kzmalloc(size_t size, int priority);
-extern char		*dgap_ioctl_name(int cmd);
-
-/*
- * Our Global Variables.
- */
-extern int		dgap_driver_state;	/* The state of the driver	*/
-extern int		dgap_debug;		/* Debug variable		*/
-extern int		dgap_rawreadok;		/* Set if user wants rawreads	*/
-extern int		dgap_poll_tick;		/* Poll interval - 20 ms	*/
-extern spinlock_t	dgap_global_lock;	/* Driver global spinlock	*/
-extern uint		dgap_NumBoards;		/* Total number of boards	*/
-extern struct board_t	*dgap_Board[MAXBOARDS];	/* Array of board structs	*/
-extern ulong		dgap_poll_counter;	/* Times the poller has run	*/
-extern char		*dgap_config_buf;	/* The config file buffer	*/
-extern spinlock_t	dgap_dl_lock;		/* Downloader spinlock		*/
-extern wait_queue_head_t dgap_dl_wait;		/* Wait queue for downloader	*/
-extern int		dgap_dl_action;		/* Action flag for downloader	*/
-extern int		dgap_registerttyswithsysfs; /* Should we register the	*/
-						    /* ttys with sysfs or not	*/
-						    
-/*
- * Functions from dgap_parsefile
- */						    
-extern int dgap_parsefile(char **in, int Remove);
-extern struct cnode *dgap_find_config(int type, int bus, int slot);
-extern uint dgap_config_get_number_of_ports(struct board_t *bd);
-extern char *dgap_create_config_string(struct board_t *bd, char *string);
-extern char *dgap_get_config_letters(struct board_t *bd, char *string);
-extern uint dgap_config_get_useintr(struct board_t *bd);
-extern uint dgap_config_get_altpin(struct board_t *bd);						    
-
-/*
- * Global functions declared in dgap_fep5.c, but must be hidden from
- * user space programs.
- */
-extern void	dgap_poll_tasklet(unsigned long data); 
-extern void	dgap_cmdb(struct channel_t *ch, uchar cmd, uchar byte1, uchar byte2, uint ncmds);
-extern void	dgap_cmdw(struct channel_t *ch, uchar cmd, u16 word, uint ncmds);
-extern void	dgap_wmove(struct channel_t *ch, char *buf, uint cnt);
-extern int	dgap_param(struct tty_struct *tty);
-extern void	dgap_parity_scan(struct channel_t *ch, unsigned char *cbuf, unsigned char *fbuf, int *len);
-extern uint	dgap_get_custom_baud(struct channel_t *ch);
-extern void	dgap_firmware_reset_port(struct channel_t *ch);
-
-/*
- * Functions prototypes from dgap_tty.h
- */
-int	dgap_tty_register(struct board_t *brd);
-
-int	dgap_tty_preinit(void);
-int     dgap_tty_init(struct board_t *);
-
-void	dgap_tty_post_uninit(void);
-void	dgap_tty_uninit(struct board_t *);
-
-void	dgap_carrier(struct channel_t *ch);
-void	dgap_input(struct channel_t *ch);
-
-/************************************************************************* 
- ***	FEP Version 5 dependent definitions
- ************************************************************************/
-
-/************************************************************************
- *      FEP memory offsets
- ************************************************************************/
-#define START           0x0004L         /* Execution start address      */
-
-#define CMDBUF          0x0d10L         /* Command (cm_t) structure offset */
-#define CMDSTART        0x0400L         /* Start of command buffer      */   
-#define CMDMAX          0x0800L         /* End of command buffer        */
-
-#define EVBUF           0x0d18L         /* Event (ev_t) structure       */
-#define EVSTART         0x0800L         /* Start of event buffer        */
-#define EVMAX           0x0c00L         /* End of event buffer          */
-#define FEP5_PLUS       0x0E40          /* ASCII '5' and ASCII 'A' is here  */
-#define ECS_SEG         0x0E44          /* Segment of the extended channel structure */
-#define LINE_SPEED      0x10            /* Offset into ECS_SEG for line speed   */
-                                        /* if the fep has extended capabilities */
-
-/* BIOS MAGIC SPOTS */
-#define ERROR           0x0C14L		/* BIOS error code              */
-#define SEQUENCE	0x0C12L		/* BIOS sequence indicator      */
-#define POSTAREA	0x0C00L		/* POST complete message area   */
-
-/* FEP MAGIC SPOTS */
-#define FEPSTAT         POSTAREA        /* OS here when FEP comes up    */
-#define NCHAN           0x0C02L         /* number of ports FEP sees     */
-#define PANIC           0x0C10L         /* PANIC area for FEP           */
-#define KMEMEM          0x0C30L         /* Memory for KME use           */   
-#define CONFIG          0x0CD0L         /* Concentrator configuration info */
-#define CONFIGSIZE      0x0030          /* configuration info size      */
-#define DOWNREQ         0x0D00          /* Download request buffer pointer */
-
-#define CHANBUF         0x1000L         /* Async channel (bs_t) structs */
-#define FEPOSSIZE       0x1FFF          /* 8K FEPOS                     */
-
-#define XEMPORTS    0xC02	/*
-				 * Offset in board memory where FEP5 stores
-				 * how many ports it has detected.
-				 * NOTE: FEP5 reports 64 ports when the user
-				 * has the cable in EBI OUT instead of EBI IN.
-				 */
-
-#define FEPCLR      0x00
-#define FEPMEM      0x02 
-#define FEPRST      0x04 
-#define FEPINT      0x08
-#define FEPMASK     0x0e
-#define FEPWIN      0x80
-
-#define LOWMEM      0x0100
-#define HIGHMEM     0x7f00
-
-#define FEPTIMEOUT 200000
-
-#define ENABLE_INTR		0x0e04		/* Enable interrupts flag */
-#define FEPPOLL_MIN		1		/* minimum of 1 millisecond */  
-#define FEPPOLL_MAX		20		/* maximum of 20 milliseconds */
-#define FEPPOLL			0x0c26		/* Fep event poll interval */   
-
-#define	IALTPIN			0x0080		/* Input flag to swap DSR <-> DCD */
-
-/************************************************************************ 
- * Command structure definition.
- ************************************************************************/
-struct cm_t {
-	volatile unsigned short cm_head;	/* Command buffer head offset	*/
-	volatile unsigned short cm_tail;	/* Command buffer tail offset	*/
-	volatile unsigned short cm_start;	/* start offset of buffer	*/
-	volatile unsigned short cm_max;		/* last offset of buffer	*/
-};
-
-/************************************************************************
- * Event structure definition.
- ************************************************************************/
-struct ev_t {
-	volatile unsigned short ev_head;	/* Command buffer head offset	*/
-	volatile unsigned short ev_tail;	/* Command buffer tail offset	*/
-	volatile unsigned short ev_start;	/* start offset of buffer	*/
-	volatile unsigned short ev_max;		/* last offset of buffer	*/
-};
-
-/************************************************************************
- * Download buffer structure.
- ************************************************************************/
-struct downld_t {
-	uchar	dl_type;		/* Header                       */
-	uchar	dl_seq;			/* Download sequence            */
-	ushort	dl_srev;		/* Software revision number     */
-	ushort	dl_lrev;		/* Low revision number          */
-	ushort	dl_hrev;		/* High revision number         */
-	ushort	dl_seg;			/* Start segment address        */
-	ushort	dl_size;		/* Number of bytes to download  */
-	uchar	dl_data[1024];		/* Download data                */
-};
-
-/************************************************************************ 
- * Per channel buffer structure
- ************************************************************************
- *              Base Structure Entries Usage Meanings to Host           * 
- *                                                                      * 
- *        W = read write        R = read only                           * 
- *        C = changed by commands only                                  * 
- *        U = unknown (may be changed w/o notice)                       *
- ************************************************************************/
-struct bs_t {
-	volatile unsigned short  tp_jmp;	/* Transmit poll jump		 */
-	volatile unsigned short  tc_jmp;	/* Cooked procedure jump	 */
-	volatile unsigned short  ri_jmp;	/* Not currently used		 */
-	volatile unsigned short  rp_jmp;	/* Receive poll jump		 */
-
-	volatile unsigned short  tx_seg;	/* W  Tx segment	 */
-	volatile unsigned short  tx_head;	/* W  Tx buffer head offset	*/
-	volatile unsigned short  tx_tail;	/* R  Tx buffer tail offset	*/
-	volatile unsigned short  tx_max;	/* W  Tx buffer size - 1	 */
- 
-	volatile unsigned short  rx_seg;	/* W  Rx segment		*/
-	volatile unsigned short  rx_head;	/* W  Rx buffer head offset	*/
-	volatile unsigned short  rx_tail;	/* R  Rx buffer tail offset	*/
-	volatile unsigned short  rx_max;	/* W  Rx buffer size - 1	 */
-
-	volatile unsigned short  tx_lw;		/* W  Tx buffer low water mark  */
-	volatile unsigned short  rx_lw;		/* W  Rx buffer low water mark  */
-	volatile unsigned short  rx_hw;		/* W  Rx buffer high water mark */
-	volatile unsigned short  incr;		/* W  Increment to next channel */
-
-	volatile unsigned short  fepdev;	/* U  SCC device base address    */
-	volatile unsigned short  edelay;	/* W  Exception delay            */
-	volatile unsigned short  blen;		/* W  Break length              */
-	volatile unsigned short  btime;		/* U  Break complete time       */
-
-	volatile unsigned short  iflag;		/* C  UNIX input flags          */
-	volatile unsigned short  oflag;		/* C  UNIX output flags         */
-	volatile unsigned short  cflag;		/* C  UNIX control flags        */
-	volatile unsigned short  wfill[13];	/* U  Reserved for expansion    */
-
-	volatile unsigned char   num;		/* U  Channel number            */
-	volatile unsigned char   ract;		/* U  Receiver active counter   */
-	volatile unsigned char   bstat;		/* U  Break status bits         */
-	volatile unsigned char   tbusy;		/* W  Transmit busy             */
-	volatile unsigned char   iempty;	/* W  Transmit empty event enable */
-	volatile unsigned char   ilow;		/* W  Transmit low-water event enable */
-	volatile unsigned char   idata;		/* W  Receive data interrupt enable */
-	volatile unsigned char   eflag;		/* U  Host event flags          */
-
-	volatile unsigned char   tflag;		/* U  Transmit flags            */
-	volatile unsigned char   rflag;		/* U  Receive flags             */
-	volatile unsigned char   xmask;		/* U  Transmit ready flags      */
-	volatile unsigned char   xval;		/* U  Transmit ready value      */
-	volatile unsigned char   m_stat;	/* RC Modem status bits          */
-	volatile unsigned char   m_change;	/* U  Modem bits which changed  */
-	volatile unsigned char   m_int;		/* W  Modem interrupt enable bits */
-	volatile unsigned char   m_last;	/* U  Last modem status         */
-
-	volatile unsigned char   mtran;		/* C   Unreported modem trans   */
-	volatile unsigned char   orun;		/* C   Buffer overrun occurred  */
-	volatile unsigned char   astartc;	/* W   Auxiliary Xon char       */  
-	volatile unsigned char   astopc;	/* W   Auxiliary Xoff char      */
-	volatile unsigned char   startc;	/* W   Xon character             */
-	volatile unsigned char   stopc;		/* W   Xoff character           */
-	volatile unsigned char   vnextc;	/* W   Vnext character           */
-	volatile unsigned char   hflow;		/* C   Software flow control    */
-
-	volatile unsigned char   fillc;		/* U   Delay Fill character     */
-	volatile unsigned char   ochar;		/* U   Saved output character   */
-	volatile unsigned char   omask;		/* U   Output character mask    */
-
-	volatile unsigned char   bfill[13];	/* U   Reserved for expansion   */  
-
-	volatile unsigned char   scc[16];	/* U   SCC registers            */
-};
-
-
-/************************************************************************   
- * FEP supported functions
- ************************************************************************/
-#define SRLOW		0xe0		/* Set receive low water	*/
-#define SRHIGH		0xe1		/* Set receive high water	*/
-#define FLUSHTX		0xe2		/* Flush transmit buffer	*/
-#define PAUSETX		0xe3		/* Pause data transmission	*/
-#define RESUMETX	0xe4		/* Resume data transmission	*/
-#define SMINT		0xe5		/* Set Modem Interrupt		*/
-#define SAFLOWC		0xe6		/* Set Aux. flow control chars	*/
-#define SBREAK		0xe8		/* Send break			*/
-#define SMODEM		0xe9		/* Set 8530 modem control lines	*/  
-#define SIFLAG		0xea		/* Set UNIX iflags		*/
-#define SFLOWC		0xeb		/* Set flow control characters	*/
-#define STLOW		0xec		/* Set transmit low water mark	*/
-#define RPAUSE		0xee		/* Pause receive		*/
-#define RRESUME		0xef		/* Resume receive		*/  
-#define CHRESET		0xf0		/* Reset Channel		*/
-#define BUFSETALL	0xf2		/* Set Tx & Rx buffer size avail*/
-#define SOFLAG		0xf3		/* Set UNIX oflags		*/
-#define SHFLOW		0xf4		/* Set hardware handshake	*/
-#define SCFLAG		0xf5		/* Set UNIX cflags		*/
-#define SVNEXT		0xf6		/* Set VNEXT character		*/
-#define SPINTFC		0xfc		/* Reserved			*/
-#define SCOMMODE	0xfd		/* Set RS232/422 mode		*/
-
-
-/************************************************************************ 
- *	Modes for SCOMMODE
- ************************************************************************/
-#define MODE_232	0x00
-#define MODE_422	0x01
-
-
-/************************************************************************ 
- *      Event flags.
- ************************************************************************/
-#define IFBREAK         0x01            /* Break received               */  
-#define IFTLW           0x02            /* Transmit low water           */
-#define IFTEM           0x04            /* Transmitter empty            */
-#define IFDATA          0x08            /* Receive data present         */
-#define IFMODEM         0x20            /* Modem status change          */
-
-/************************************************************************   
- *      Modem flags
- ************************************************************************/
-#       define  DM_RTS          0x02    /* Request to send              */
-#       define  DM_CD           0x80    /* Carrier detect               */
-#       define  DM_DSR          0x20    /* Data set ready               */
-#       define  DM_CTS          0x10    /* Clear to send                */
-#       define  DM_RI           0x40    /* Ring indicator               */
-#       define  DM_DTR          0x01    /* Data terminal ready          */
-
-
-/************************************************************************
- * Stuf from dgap_conf.h
- ************************************************************************/
-
-#define NULLNODE 0		/* header node, not used */
-#define BNODE 1			/* Board node */
-#define LNODE 2			/* Line node */
-#define CNODE 3			/* Concentrator node */
-#define MNODE 4			/* EBI Module node */
-#define TNODE 5			/* tty name prefix node */
-#define	CUNODE 6		/* cu name prefix (non-SCO) */
-#define PNODE 7			/* trans. print prefix node */
-#define JNODE 8			/* maJor number node */
-#define ANODE 9			/* altpin */
-#define	TSNODE 10		/* tty structure size */
-#define CSNODE 11		/* channel structure size */
-#define BSNODE 12		/* board structure size */
-#define USNODE 13		/* unit schedule structure size */
-#define FSNODE 14		/* f2200 structure size */
-#define VSNODE 15		/* size of VPIX structures */
-#define INTRNODE 16		/* enable interrupt */
-
-/* Enumeration of tokens */
-#define	BEGIN	1
-#define	END	2
-#define	BOARD	10
-
-#define EPCFS	11 /* start of EPC family definitions */
-#define	ICX		11
-#define	MCX		13
-#define PCX	14
-#define	IEPC	15
-#define	EEPC	16
-#define	MEPC	17
-#define	IPCM	18
-#define	EPCM	19
-#define	MPCM	20
-#define PEPC	21
-#define PPCM	22
-#ifdef CP
-#define ICP     23
-#define ECP     24
-#define MCP     25
-#endif
-#define EPCFE	25 /* end of EPC family definitions */
-#define	PC2E	26
-#define	PC4E	27
-#define	PC4E8K	28
-#define	PC8E	29
-#define	PC8E8K	30
-#define	PC16E	31
-#define MC2E8K  34
-#define MC4E8K  35
-#define MC8E8K  36
-
-#define AVANFS	42	/* start of Avanstar family definitions */
-#define A8P 	42
-#define A16P	43
-#define AVANFE	43	/* end of Avanstar family definitions */
-
-#define DA2000FS	44	/* start of AccelePort 2000 family definitions */
-#define DA22 		44 /* AccelePort 2002 */
-#define DA24 		45 /* AccelePort 2004 */
-#define DA28		46 /* AccelePort 2008 */
-#define DA216		47 /* AccelePort 2016 */
-#define DAR4		48 /* AccelePort RAS 4 port */
-#define DAR8		49 /* AccelePort RAS 8 port */
-#define DDR24		50 /* DataFire RAS 24 port */
-#define DDR30		51 /* DataFire RAS 30 port */
-#define DDR48		52 /* DataFire RAS 48 port */
-#define DDR60		53 /* DataFire RAS 60 port */
-#define DA2000FE	53 /* end of AccelePort 2000/RAS family definitions */
-
-#define PCXRFS	106	/* start of PCXR family definitions */
-#define	APORT4	106
-#define	APORT8	107
-#define PAPORT4 108
-#define PAPORT8 109
-#define APORT4_920I	110
-#define APORT8_920I	111
-#define APORT4_920P	112
-#define APORT8_920P	113
-#define APORT2_920P 114
-#define PCXRFE	117	/* end of PCXR family definitions */
-
-#define	LINE	82
-#ifdef T1
-#define T1M	83
-#define E1M	84
-#endif
-#define	CONC	64
-#define	CX	65
-#define	EPC	66
-#define	MOD	67
-#define	PORTS	68
-#define METHOD	69
-#define CUSTOM	70
-#define BASIC	71
-#define STATUS	72
-#define MODEM	73
-/* The following tokens can appear in multiple places */
-#define	SPEED	74
-#define	NPORTS	75
-#define	ID	76
-#define CABLE	77
-#define CONNECT	78
-#define	IO	79
-#define	MEM	80
-#define DPSZ	81
-
-#define	TTYN	90
-#define	CU	91
-#define	PRINT	92
-#define	XPRINT	93
-#define CMAJOR   94 
-#define ALTPIN  95
-#define STARTO 96
-#define USEINTR  97
-#define PCIINFO  98
-
-#define	TTSIZ	100
-#define	CHSIZ	101
-#define BSSIZ	102
-#define	UNTSIZ	103
-#define	F2SIZ	104
-#define	VPSIZ	105
-
-#define	TOTAL_BOARD	2
-#define	CURRENT_BRD	4
-#define	BOARD_TYPE	6
-#define	IO_ADDRESS	8
-#define	MEM_ADDRESS	10
-
-#define	FIELDS_PER_PAGE	18
-
-#define TB_FIELD	1
-#define CB_FIELD	3
-#define BT_FIELD	5
-#define IO_FIELD	7
-#define ID_FIELD	8
-#define ME_FIELD	9
-#define TTY_FIELD	11
-#define CU_FIELD	13
-#define PR_FIELD	15
-#define MPR_FIELD	17
-
-#define	MAX_FIELD	512
-
-#define	INIT		0
-#define	NITEMS		128
-#define MAX_ITEM	512
-
-#define	DSCRINST	1
-#define	DSCRNUM		3
-#define	ALTPINQ		5
-#define	SSAVE		7
-
-#define	DSCR		"32"
-#define	ONETONINE	"123456789"
-#define	ALL		"1234567890"
-
-
-struct cnode {
-	struct cnode *next;
-	int type;
-	int numbrd;
-
-	union {
-		struct {
-			char  type;	/* Board Type 		*/
-			short port;	/* I/O Address		*/
-			char  *portstr; /* I/O Address in string */
-			long  addr;	/* Memory Address	*/
-			char  *addrstr; /* Memory Address in string */
-			long  pcibus;	/* PCI BUS		*/
-			char  *pcibusstr; /* PCI BUS in string */
-			long  pcislot;	/* PCI SLOT		*/
-			char  *pcislotstr; /* PCI SLOT in string */
-			char  nport;	/* Number of Ports	*/
-			char  *id;	/* tty id		*/
-			int   start;	/* start of tty counting */
-			char  *method;  /* Install method       */
-			char  v_type;
-			char  v_port;
-			char  v_addr;
-			char  v_pcibus;
-			char  v_pcislot;
-			char  v_nport;
-			char  v_id;
-			char  v_start;
-			char  v_method;
-			char  line1;
-			char  line2;
-			char  conc1;   /* total concs in line1 */
-			char  conc2;   /* total concs in line2 */
-			char  module1; /* total modules for line1 */
-			char  module2; /* total modules for line2 */
-			char  *status; /* config status */
-			char  *dimstatus;	 /* Y/N */
-			int   status_index; /* field pointer */
-		} board;
-
-		struct {
-			char  *cable;
-			char  v_cable;
-			char  speed;
-			char  v_speed;
-		} line;
-
-		struct {
-			char  type;
-			char  *connect;
-			char  speed;
-			char  nport;
-			char  *id;
-			char  *idstr;
-			int   start;
-			char  v_type;
-			char  v_connect;
-			char  v_speed;
-			char  v_nport;
-			char  v_id;
-			char  v_start;
-		} conc;
-
-		struct {
-			char type;
-			char nport;
-			char *id;
-			char *idstr;
-			int  start;
-			char v_type;
-			char v_nport;
-			char v_id;
-			char v_start;
-		} module;
-
-		char *ttyname;
-		
-		char *cuname;
-		
-		char *printname;
-
-		int  majornumber;
-
-		int  altpin;
-
-		int  ttysize;
-
-		int  chsize;
-
-		int  bssize;
-
-		int  unsize;
-
-		int  f2size;
-
-		int  vpixsize;
-
-		int  useintr;
-	} u;
-};
-
-#endif
diff -urpN linux-3.13.1-orig/drivers/staging/dgap/dgap.h linux-3.13.1-new/drivers/staging/dgap/dgap.h
--- linux-3.13.1-orig/drivers/staging/dgap/dgap.h	1969-12-31 19:00:00.000000000 -0500
+++ linux-3.13.1-new/drivers/staging/dgap/dgap.h	2014-02-11 10:17:49.137517346 -0500
@@ -0,0 +1,1566 @@
+/*
+ * Copyright 2003 Digi International (www.digi.com)
+ *      Scott H Kilau <Scott_Kilau at digi dot com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY, EXPRESS OR IMPLIED; without even the
+ * implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
+ * PURPOSE.  See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *	NOTE: THIS IS A SHARED HEADER. DO NOT CHANGE CODING STYLE!!!
+ *
+ *************************************************************************
+ *
+ * Driver includes
+ *
+ *************************************************************************/
+
+#ifndef __DGAP_DRIVER_H
+#define __DGAP_DRIVER_H
+
+#include <linux/version.h>	/* To get the current Linux version */
+#include <linux/types.h>        /* To pick up the varions Linux types */
+#include <linux/tty.h>          /* To pick up the various tty structs/defines */
+#include <linux/interrupt.h>    /* For irqreturn_t type */
+
+#if !defined(TTY_FLIPBUF_SIZE)
+# define TTY_FLIPBUF_SIZE 512
+#endif
+
+#define PARM_INT(VAR, INIT, PERM, DESC) \
+		static int VAR = INIT; \
+		int dgap_##VAR; \
+		module_param(VAR, int, PERM); \
+		MODULE_PARM_DESC(VAR, DESC);
+
+/*************************************************************************
+ *
+ * Driver defines
+ *
+ *************************************************************************/
+
+/*
+ * Driver identification, error and debugging statments
+ *
+ * In theory, you can change all occurrences of "digi" in the next
+ * three lines, and the driver printk's will all automagically change.
+ *
+ * APR((fmt, args, ...));	Always prints message
+ * DPR((fmt, args, ...));	Only prints if DGAP_TRACER is defined at
+ *				  compile time and dgap_debug!=0
+ */
+#define	DG_NAME		"dgap-1.3-16"
+#define	DG_PART		"40002347_C"
+
+#define	PROCSTR		"dgap"			/* /proc entries	 */
+#define	DEVSTR		"/dev/dg/dgap"		/* /dev entries		 */
+#define	DRVSTR		"dgap"			/* Driver name string 
+						 * displayed by APR	 */
+#define	APR(args)	do { PRINTF_TO_KMEM(args); printk(DRVSTR": "); printk args; \
+			   } while (0)
+#define	RAPR(args)	do { PRINTF_TO_KMEM(args); printk args; } while (0)
+
+#define TRC_TO_CONSOLE 1
+
+#ifndef TRUE
+# define TRUE 1
+#endif
+
+#ifndef FALSE
+# define FALSE 0
+#endif
+
+/* Required for our shared headers! */
+typedef unsigned char           uchar;
+
+/************************************************************************
+ * Stuff from dgap_pci.h
+ ************************************************************************/
+#define PCIMAX 32			/* maximum number of PCI boards */
+
+#define DIGI_VID		0x114F
+
+#define PCI_DEVICE_EPC_DID	0x0002
+#define PCI_DEVICE_XEM_DID	0x0004
+#define PCI_DEVICE_XR_DID	0x0005
+#define PCI_DEVICE_CX_DID	0x0006
+#define PCI_DEVICE_XRJ_DID	0x0009	/* PLX-based Xr adapter */
+#define PCI_DEVICE_XR_IBM_DID	0x0011	/* IBM 8-port Async Adapter */
+#define PCI_DEVICE_XR_BULL_DID	0x0013	/* BULL 8-port Async Adapter */
+#define PCI_DEVICE_XR_SAIP_DID	0x001c	/* SAIP card - Xr adapter */
+#define PCI_DEVICE_XR_422_DID	0x0012	/* Xr-422 */
+#define PCI_DEVICE_920_2_DID	0x0034	/* XR-Plus 920 K, 2 port */
+#define PCI_DEVICE_920_4_DID	0x0026	/* XR-Plus 920 K, 4 port */
+#define PCI_DEVICE_920_8_DID	0x0027	/* XR-Plus 920 K, 8 port */
+#define PCI_DEVICE_EPCJ_DID	0x000a	/* PLX 9060 chip for PCI  */
+#define PCI_DEVICE_CX_IBM_DID	0x001b	/* IBM 128-port Async Adapter */
+#define PCI_DEVICE_920_8_HP_DID	0x0058	/* HP XR-Plus 920 K, 8 port */
+#define PCI_DEVICE_XEM_HP_DID	0x0059  /* HP Xem PCI */
+
+#define PCI_DEVICE_XEM_NAME	"AccelePort XEM"
+#define PCI_DEVICE_CX_NAME	"AccelePort CX"
+#define PCI_DEVICE_XR_NAME	"AccelePort Xr"
+#define PCI_DEVICE_XRJ_NAME	"AccelePort Xr (PLX)"
+#define PCI_DEVICE_XR_SAIP_NAME	"AccelePort Xr (SAIP)"
+#define PCI_DEVICE_920_2_NAME	"AccelePort Xr920 2 port"
+#define PCI_DEVICE_920_4_NAME	"AccelePort Xr920 4 port"
+#define PCI_DEVICE_920_8_NAME	"AccelePort Xr920 8 port"
+#define PCI_DEVICE_XR_422_NAME	"AccelePort Xr 422"
+#define PCI_DEVICE_EPCJ_NAME	"AccelePort EPC (PLX)"
+#define PCI_DEVICE_XR_BULL_NAME	"AccelePort Xr (BULL)"
+#define PCI_DEVICE_XR_IBM_NAME	"AccelePort Xr (IBM)"
+#define PCI_DEVICE_CX_IBM_NAME	"AccelePort CX (IBM)"
+#define PCI_DEVICE_920_8_HP_NAME "AccelePort Xr920 8 port (HP)"
+#define PCI_DEVICE_XEM_HP_NAME	"AccelePort XEM (HP)"
+
+
+/*
+ * On the PCI boards, there is no IO space allocated
+ * The I/O registers will be in the first 3 bytes of the
+ * upper 2MB of the 4MB memory space.  The board memory
+ * will be mapped into the low 2MB of the 4MB memory space
+ */
+
+/* Potential location of PCI Bios from E0000 to FFFFF*/
+#define PCI_BIOS_SIZE		0x00020000
+
+/* Size of Memory and I/O for PCI (4MB) */
+#define PCI_RAM_SIZE		0x00400000
+
+/* Size of Memory (2MB) */
+#define PCI_MEM_SIZE		0x00200000
+
+/* Max PCI Window Size (2MB) */
+#define PCI_WIN_SIZE		0x00200000
+
+#define PCI_WIN_SHIFT		21 /* 21 bits max */
+
+/* Offset of I/0 in Memory (2MB) */
+#define PCI_IO_OFFSET		0x00200000
+
+/* Size of IO (2MB) */
+#define PCI_IO_SIZE		0x00200000
+
+/************************************************************************
+ ***	Definitions for Digi ditty(1) command.
+ ************************************************************************/
+
+
+/*
+ * Copyright (c) 1988-96 Digi International Inc., All Rights Reserved.
+ */
+
+/************************************************************************
+ * This module provides application access to special Digi
+ * serial line enhancements which are not standard UNIX(tm) features.
+ ************************************************************************/
+
+#if !defined(TIOCMODG)
+
+#define	TIOCMODG	('d'<<8) | 250		/* get modem ctrl state	*/
+#define	TIOCMODS	('d'<<8) | 251		/* set modem ctrl state	*/
+
+#ifndef TIOCM_LE 
+#define		TIOCM_LE	0x01		/* line enable		*/
+#define		TIOCM_DTR	0x02		/* data terminal ready	*/
+#define		TIOCM_RTS	0x04		/* request to send	*/
+#define		TIOCM_ST	0x08		/* secondary transmit	*/
+#define		TIOCM_SR	0x10		/* secondary receive	*/
+#define		TIOCM_CTS	0x20		/* clear to send	*/
+#define		TIOCM_CAR	0x40		/* carrier detect	*/
+#define		TIOCM_RNG	0x80		/* ring	indicator	*/
+#define		TIOCM_DSR	0x100		/* data set ready	*/
+#define		TIOCM_RI	TIOCM_RNG	/* ring (alternate)	*/
+#define		TIOCM_CD	TIOCM_CAR	/* carrier detect (alt)	*/
+#endif
+
+#endif
+
+#if !defined(TIOCMSET)
+#define	TIOCMSET	('d'<<8) | 252		/* set modem ctrl state	*/
+#define	TIOCMGET	('d'<<8) | 253		/* set modem ctrl state	*/
+#endif
+
+#if !defined(TIOCMBIC)
+#define	TIOCMBIC	('d'<<8) | 254		/* set modem ctrl state */
+#define	TIOCMBIS	('d'<<8) | 255		/* set modem ctrl state */
+#endif
+
+
+#if !defined(TIOCSDTR)
+#define	TIOCSDTR	('e'<<8) | 0		/* set DTR		*/
+#define	TIOCCDTR	('e'<<8) | 1		/* clear DTR		*/
+#endif
+
+/************************************************************************
+ * Ioctl command arguments for DIGI parameters.
+ ************************************************************************/
+#define DIGI_GETA	('e'<<8) | 94		/* Read params		*/
+
+#define DIGI_SETA	('e'<<8) | 95		/* Set params		*/
+#define DIGI_SETAW	('e'<<8) | 96		/* Drain & set params	*/
+#define DIGI_SETAF	('e'<<8) | 97		/* Drain, flush & set params */
+
+#define DIGI_KME	('e'<<8) | 98		/* Read/Write Host	*/
+						/* Adapter Memory	*/
+
+#define	DIGI_GETFLOW	('e'<<8) | 99		/* Get startc/stopc flow */
+						/* control characters 	 */
+#define	DIGI_SETFLOW	('e'<<8) | 100		/* Set startc/stopc flow */
+						/* control characters	 */
+#define	DIGI_GETAFLOW	('e'<<8) | 101		/* Get Aux. startc/stopc */
+						/* flow control chars 	 */
+#define	DIGI_SETAFLOW	('e'<<8) | 102		/* Set Aux. startc/stopc */
+						/* flow control chars	 */
+
+#define DIGI_GEDELAY	('d'<<8) | 246		/* Get edelay */
+#define DIGI_SEDELAY	('d'<<8) | 247		/* Set edelay */
+
+struct	digiflow_t {
+	unsigned char	startc;				/* flow cntl start char	*/
+	unsigned char	stopc;				/* flow cntl stop char	*/
+};
+
+
+#ifdef	FLOW_2200
+#define	F2200_GETA	('e'<<8) | 104		/* Get 2x36 flow cntl flags */
+#define	F2200_SETAW	('e'<<8) | 105		/* Set 2x36 flow cntl flags */
+#define		F2200_MASK	0x03		/* 2200 flow cntl bit mask  */
+#define		FCNTL_2200	0x01		/* 2x36 terminal flow cntl  */
+#define		PCNTL_2200	0x02		/* 2x36 printer flow cntl   */
+#define	F2200_XON	0xf8
+#define	P2200_XON	0xf9
+#define	F2200_XOFF	0xfa
+#define	P2200_XOFF	0xfb
+
+#define	FXOFF_MASK	0x03			/* 2200 flow status mask    */
+#define	RCVD_FXOFF	0x01			/* 2x36 Terminal XOFF rcvd  */
+#define	RCVD_PXOFF	0x02			/* 2x36 Printer XOFF rcvd   */
+#endif
+
+/************************************************************************
+ * Values for digi_flags 
+ ************************************************************************/
+#define DIGI_IXON	0x0001		/* Handle IXON in the FEP	*/
+#define DIGI_FAST	0x0002		/* Fast baud rates		*/
+#define RTSPACE		0x0004		/* RTS input flow control	*/
+#define CTSPACE		0x0008		/* CTS output flow control	*/
+#define DSRPACE		0x0010		/* DSR output flow control	*/
+#define DCDPACE		0x0020		/* DCD output flow control	*/
+#define DTRPACE		0x0040		/* DTR input flow control	*/
+#define DIGI_COOK	0x0080		/* Cooked processing done in FEP */
+#define DIGI_FORCEDCD	0x0100		/* Force carrier		*/
+#define	DIGI_ALTPIN	0x0200		/* Alternate RJ-45 pin config	*/
+#define	DIGI_AIXON	0x0400		/* Aux flow control in fep	*/
+#define	DIGI_PRINTER	0x0800		/* Hold port open for flow cntrl*/
+#define DIGI_PP_INPUT	0x1000		/* Change parallel port to input*/
+#define DIGI_DTR_TOGGLE 0x2000		/* Support DTR Toggle		*/
+#define	DIGI_422	0x4000		/* for 422/232 selectable panel */
+#define DIGI_RTS_TOGGLE	0x8000		/* Support RTS Toggle		*/
+
+/************************************************************************
+ * These options are not supported on the comxi.
+ ************************************************************************/
+#define	DIGI_COMXI	(DIGI_FAST|DIGI_COOK|DSRPACE|DCDPACE|DTRPACE)
+
+#define DIGI_PLEN	28		/* String length		*/
+#define	DIGI_TSIZ	10		/* Terminal string len		*/
+
+/************************************************************************
+ * Structure used with ioctl commands for DIGI parameters.
+ ************************************************************************/
+struct digi_t {
+	unsigned short	digi_flags;		/* Flags (see above)	*/
+	unsigned short	digi_maxcps;		/* Max printer CPS	*/
+	unsigned short	digi_maxchar;		/* Max chars in print queue */
+	unsigned short	digi_bufsize;		/* Buffer size		*/
+	unsigned char	digi_onlen;		/* Length of ON string	*/
+	unsigned char	digi_offlen;		/* Length of OFF string	*/
+	char		digi_onstr[DIGI_PLEN];	/* Printer on string	*/
+	char		digi_offstr[DIGI_PLEN];	/* Printer off string	*/
+	char		digi_term[DIGI_TSIZ];	/* terminal string	*/
+};
+
+/************************************************************************
+ * KME definitions and structures.
+ ************************************************************************/
+#define	RW_IDLE		0	/* Operation complete			*/
+#define	RW_READ		1	/* Read Concentrator Memory		*/
+#define	RW_WRITE	2	/* Write Concentrator Memory		*/
+
+struct rw_t {
+	unsigned char	rw_req;		/* Request type			*/
+	unsigned char	rw_board;	/* Host Adapter board number	*/
+	unsigned char	rw_conc;	/* Concentrator number		*/
+	unsigned char	rw_reserved;	/* Reserved for expansion	*/
+	unsigned long	rw_addr;	/* Address in concentrator	*/
+	unsigned short	rw_size;	/* Read/write request length	*/
+	unsigned char	rw_data[128];	/* Data to read/write		*/
+};
+
+/***********************************************************************
+ * Shrink Buffer and Board Information definitions and structures.
+
+ ************************************************************************/
+			/* Board type return codes */
+#define	PCXI_TYPE 1     /* Board type at the designated port is a PC/Xi */
+#define PCXM_TYPE 2     /* Board type at the designated port is a PC/Xm */
+#define	PCXE_TYPE 3     /* Board type at the designated port is a PC/Xe */
+#define	MCXI_TYPE 4     /* Board type at the designated port is a MC/Xi */
+#define COMXI_TYPE 5     /* Board type at the designated port is a COM/Xi */
+
+			 /* Non-Zero Result codes. */
+#define RESULT_NOBDFND 1 /* A Digi product at that port is not config installed */ 
+#define RESULT_NODESCT 2 /* A memory descriptor was not obtainable */ 
+#define RESULT_NOOSSIG 3 /* FEP/OS signature was not detected on the board */
+#define RESULT_TOOSML  4 /* Too small an area to shrink.  */
+#define RESULT_NOCHAN  5 /* Channel structure for the board was not found */
+
+struct shrink_buf_struct {
+	unsigned long	shrink_buf_vaddr;	/* Virtual address of board */
+	unsigned long	shrink_buf_phys;	/* Physical address of board */
+	unsigned long	shrink_buf_bseg;	/* Amount of board memory */
+	unsigned long	shrink_buf_hseg;	/* '186 Beginning of Dual-Port */
+
+	unsigned long	shrink_buf_lseg;	/* '186 Beginning of freed memory						*/ 
+	unsigned long	shrink_buf_mseg;	/* Linear address from start of
+						   dual-port were freed memory
+						   begins, host viewpoint. */
+
+	unsigned long	shrink_buf_bdparam;	/* Parameter for xxmemon and
+						   xxmemoff */
+
+	unsigned long	shrink_buf_reserva;	/* Reserved */
+	unsigned long	shrink_buf_reservb;	/* Reserved */
+	unsigned long	shrink_buf_reservc;	/* Reserved */
+	unsigned long	shrink_buf_reservd;	/* Reserved */
+
+	unsigned char	shrink_buf_result;	/* Reason for call failing
+						   Zero is Good return */
+	unsigned char	shrink_buf_init;	/* Non-Zero if it caused an     
+						   xxinit call. */
+
+	unsigned char	shrink_buf_anports;	/* Number of async ports  */
+	unsigned char	shrink_buf_snports; 	/* Number of sync  ports */
+	unsigned char	shrink_buf_type;	/* Board type 1 = PC/Xi,
+							      2 = PC/Xm,
+							      3 = PC/Xe  
+							      4 = MC/Xi  
+							      5 = COMX/i */
+	unsigned char	shrink_buf_card;	/* Card number */
+	
+};
+
+/************************************************************************
+ * Structure to get driver status information
+ ************************************************************************/
+struct digi_dinfo {
+	unsigned long	dinfo_nboards;		/* # boards configured	*/
+	char		dinfo_reserved[12];	/* for future expansion */
+	char		dinfo_version[16];	/* driver version       */
+};
+
+#define	DIGI_GETDD	('d'<<8) | 248		/* get driver info      */
+ 
+/************************************************************************
+ * Structure used with ioctl commands for per-board information
+ *
+ * physsize and memsize differ when board has "windowed" memory
+ ************************************************************************/
+struct digi_info {
+	unsigned long	info_bdnum;		/* Board number (0 based)  */
+	unsigned long	info_ioport;		/* io port address         */
+	unsigned long	info_physaddr;		/* memory address          */
+	unsigned long	info_physsize;		/* Size of host mem window */
+	unsigned long	info_memsize;		/* Amount of dual-port mem */
+						/* on board                */
+	unsigned short	info_bdtype;		/* Board type              */
+	unsigned short	info_nports;		/* number of ports         */
+	char		info_bdstate;		/* board state             */
+	char		info_reserved[7];	/* for future expansion    */
+};
+
+#define	DIGI_GETBD	('d'<<8) | 249		/* get board info          */
+ 
+struct digi_stat {
+	unsigned int	info_chan;		/* Channel number (0 based)  */
+	unsigned int	info_brd;		/* Board number (0 based)  */
+	unsigned long	info_cflag;		/* cflag for channel       */
+	unsigned long	info_iflag;		/* iflag for channel       */
+	unsigned long	info_oflag;		/* oflag for channel       */
+	unsigned long	info_mstat;		/* mstat for channel       */
+	unsigned long	info_tx_data;		/* tx_data for channel       */
+	unsigned long	info_rx_data;		/* rx_data for channel       */
+	unsigned long	info_hflow;		/* hflow for channel       */
+	unsigned long	info_reserved[8];	/* for future expansion    */
+};
+
+#define	DIGI_GETSTAT	('d'<<8) | 244		/* get board info          */
+/************************************************************************
+ *
+ * Structure used with ioctl commands for per-channel information
+ *
+ ************************************************************************/
+struct digi_ch {
+	unsigned long	info_bdnum;		/* Board number (0 based)  */
+	unsigned long	info_channel;		/* Channel index number    */
+	unsigned long	info_ch_cflag;		/* Channel cflag   	   */
+	unsigned long	info_ch_iflag;		/* Channel iflag   	   */
+	unsigned long	info_ch_oflag;		/* Channel oflag   	   */
+	unsigned long	info_chsize;		/* Channel structure size  */
+	unsigned long	info_sleep_stat;	/* sleep status		   */
+	dev_t		info_dev;		/* device number	   */
+	unsigned char	info_initstate;		/* Channel init state	   */
+	unsigned char	info_running;		/* Channel running state   */
+	long		reserved[8];		/* reserved for future use */
+};
+
+/*
+* This structure is used with the DIGI_FEPCMD ioctl to 
+* tell the driver which port to send the command for.
+*/
+struct digi_cmd {
+	int	cmd;
+	int	word;
+	int	ncmds;
+	int	chan; /* channel index (zero based) */
+	int	bdid; /* board index (zero based) */
+};
+
+/*
+*  info_sleep_stat defines
+*/
+#define INFO_RUNWAIT	0x0001
+#define INFO_WOPEN	0x0002
+#define INFO_TTIOW	0x0004
+#define INFO_CH_RWAIT	0x0008
+#define INFO_CH_WEMPTY	0x0010
+#define INFO_CH_WLOW	0x0020
+#define INFO_XXBUF_BUSY 0x0040
+
+#define	DIGI_GETCH	('d'<<8) | 245		/* get board info          */
+
+/* Board type definitions */
+
+#define	SUBTYPE		0007
+#define	T_PCXI		0000
+#define T_PCXM		0001
+#define T_PCXE		0002
+#define T_PCXR		0003
+#define T_SP		0004
+#define T_SP_PLUS	0005
+#	define T_HERC	0000
+#	define T_HOU	0001
+#	define T_LON	0002
+#	define T_CHA	0003
+#define FAMILY		0070
+#define T_COMXI		0000
+#define T_PCXX		0010
+#define T_CX		0020
+#define T_EPC		0030
+#define	T_PCLITE	0040
+#define	T_SPXX		0050
+#define	T_AVXX		0060
+#define T_DXB		0070
+#define T_A2K_4_8	0070
+#define BUSTYPE		0700
+#define T_ISABUS	0000
+#define T_MCBUS		0100
+#define	T_EISABUS	0200
+#define	T_PCIBUS	0400
+
+/* Board State Definitions */
+
+#define	BD_RUNNING	0x0
+#define	BD_REASON	0x7f
+#define	BD_NOTFOUND	0x1
+#define	BD_NOIOPORT	0x2
+#define	BD_NOMEM	0x3
+#define	BD_NOBIOS	0x4
+#define	BD_NOFEP	0x5
+#define	BD_FAILED	0x6
+#define BD_ALLOCATED	0x7
+#define BD_TRIBOOT	0x8
+#define	BD_BADKME	0x80
+
+#define DIGI_LOOPBACK	      ('d'<<8) | 252		/* Enable/disable UART internal loopback */
+#define DIGI_SPOLL            ('d'<<8) | 254		/* change poller rate   */
+
+#define DIGI_SETCUSTOMBAUD	_IOW('e', 106, int)	/* Set integer baud rate */
+#define DIGI_GETCUSTOMBAUD	_IOR('e', 107, int)	/* Get integer baud rate */
+#define DIGI_RESET_PORT		('e'<<8) | 93		/* Reset port		*/
+
+
+/*
+ * Debugging levels can be set using debug insmod variable
+ * They can also be compiled out completely.
+ */
+
+#define	DBG_INIT		(dgap_debug & 0x01)
+#define	DBG_BASIC		(dgap_debug & 0x02)
+#define	DBG_CORE		(dgap_debug & 0x04)
+
+#define	DBG_OPEN		(dgap_debug & 0x08)
+#define	DBG_CLOSE		(dgap_debug & 0x10)
+#define	DBG_READ		(dgap_debug & 0x20)
+#define	DBG_WRITE		(dgap_debug & 0x40)
+
+#define	DBG_IOCTL		(dgap_debug & 0x80)
+
+#define	DBG_PROC		(dgap_debug & 0x100)
+#define	DBG_PARAM		(dgap_debug & 0x200)
+#define	DBG_PSCAN		(dgap_debug & 0x400)
+#define	DBG_EVENT		(dgap_debug & 0x800)
+
+#define	DBG_DRAIN		(dgap_debug & 0x1000)
+#define	DBG_CARR		(dgap_debug & 0x2000)
+
+#define	DBG_MGMT		(dgap_debug & 0x4000)
+
+
+#if defined(DGAP_TRACER)
+
+# if defined(TRC_TO_KMEM)
+/* Choose one: */
+#  define TRC_ON_OVERFLOW_WRAP_AROUND
+#  undef  TRC_ON_OVERFLOW_SHIFT_BUFFER
+# endif //TRC_TO_KMEM
+
+# define TRC_MAXMSG		1024
+# define TRC_OVERFLOW		"(OVERFLOW)"
+# define TRC_DTRC		"/usr/bin/dtrc"
+
+#if defined TRC_TO_CONSOLE
+#define PRINTF_TO_CONSOLE(args) { printk(DRVSTR": "); printk args; }
+#else //!defined TRACE_TO_CONSOLE
+#define PRINTF_TO_CONSOLE(args)
+#endif
+
+#if defined TRC_TO_KMEM
+#define PRINTF_TO_KMEM(args) dgap_tracef args 
+#else //!defined TRC_TO_KMEM
+#define PRINTF_TO_KMEM(args)
+#endif
+
+#define	TRC(args)	{ PRINTF_TO_KMEM(args); PRINTF_TO_CONSOLE(args) }
+
+# define DPR_INIT(ARGS)		if (DBG_INIT) TRC(ARGS)
+# define DPR_BASIC(ARGS)	if (DBG_BASIC) TRC(ARGS)
+# define DPR_CORE(ARGS)		if (DBG_CORE) TRC(ARGS)
+# define DPR_OPEN(ARGS)		if (DBG_OPEN)  TRC(ARGS)
+# define DPR_CLOSE(ARGS)	if (DBG_CLOSE)  TRC(ARGS)
+# define DPR_READ(ARGS)		if (DBG_READ)  TRC(ARGS)
+# define DPR_WRITE(ARGS)	if (DBG_WRITE) TRC(ARGS)
+# define DPR_IOCTL(ARGS)	if (DBG_IOCTL) TRC(ARGS)
+# define DPR_PROC(ARGS)		if (DBG_PROC)  TRC(ARGS)
+# define DPR_PARAM(ARGS)	if (DBG_PARAM)  TRC(ARGS)
+# define DPR_PSCAN(ARGS)	if (DBG_PSCAN)  TRC(ARGS)
+# define DPR_EVENT(ARGS)	if (DBG_EVENT)  TRC(ARGS)
+# define DPR_DRAIN(ARGS)	if (DBG_DRAIN)  TRC(ARGS)
+# define DPR_CARR(ARGS)		if (DBG_CARR)  TRC(ARGS)
+# define DPR_MGMT(ARGS)		if (DBG_MGMT)  TRC(ARGS)
+
+# define DPR(ARGS)		if (dgap_debug) TRC(ARGS)
+# define P(X)			dgap_tracef(#X "=%p\n", X)
+# define X(X)			dgap_tracef(#X "=%x\n", X)
+
+#else//!defined DGAP_TRACER
+
+#define PRINTF_TO_KMEM(args)
+# define TRC(ARGS)
+# define DPR_INIT(ARGS)
+# define DPR_BASIC(ARGS)
+# define DPR_CORE(ARGS)
+# define DPR_OPEN(ARGS)
+# define DPR_CLOSE(ARGS)
+# define DPR_READ(ARGS)
+# define DPR_WRITE(ARGS)
+# define DPR_IOCTL(ARGS)
+# define DPR_PROC(ARGS)
+# define DPR_PARAM(ARGS)
+# define DPR_PSCAN(ARGS)
+# define DPR_EVENT(ARGS)
+# define DPR_DRAIN(ARGS)
+# define DPR_CARR(ARGS)
+# define DPR_MGMT(ARGS)
+
+# define DPR(args)
+
+#endif//DGAP_TRACER
+
+/* Number of boards we support at once. */
+#define	MAXBOARDS	32
+#define	MAXPORTS	224
+#define MAXTTYNAMELEN	200
+
+/* Our 3 magic numbers for our board, channel and unit structs */
+#define DGAP_BOARD_MAGIC	0x5c6df104
+#define DGAP_CHANNEL_MAGIC	0x6c6df104
+#define DGAP_UNIT_MAGIC		0x7c6df104
+
+/* Serial port types */
+#define DGAP_SERIAL		0
+#define DGAP_PRINT		1
+
+#define	SERIAL_TYPE_NORMAL	1
+
+/* 4 extra for alignment play space */
+#define WRITEBUFLEN		((4096) + 4)
+#define MYFLIPLEN		N_TTY_BUF_SIZE
+
+#define SBREAK_TIME 0x25
+#define U2BSIZE 0x400
+
+#define dgap_jiffies_from_ms(a) (((a) * HZ) / 1000)
+
+/*
+ * Our major for the mgmt devices.
+ *
+ * We can use 22, because Digi was allocated 22 and 23 for the epca driver.
+ * 22 has now become obsolete now that the "cu" devices have 
+ * been removed from 2.6.
+ * Also, this *IS* the epca driver, just PCI only now.
+ */
+#ifndef DIGI_DGAP_MAJOR
+# define DIGI_DGAP_MAJOR         22
+#endif
+
+/*
+ * The parameters we use to define the periods of the moving averages.
+ */
+#define		MA_PERIOD	(HZ / 10)
+#define		SMA_DUR		(1 * HZ)
+#define		EMA_DUR		(1 * HZ)
+#define		SMA_NPERIODS	(SMA_DUR / MA_PERIOD)
+#define		EMA_NPERIODS	(EMA_DUR / MA_PERIOD)
+
+/*
+ * Define a local default termios struct. All ports will be created
+ * with this termios initially.  This is the same structure that is defined
+ * as the default in tty_io.c with the same settings overriden as in serial.c
+ *
+ * In short, this should match the internal serial ports' defaults.
+ */
+#define	DEFAULT_IFLAGS	(ICRNL | IXON)
+#define	DEFAULT_OFLAGS	(OPOST | ONLCR)
+#define	DEFAULT_CFLAGS	(B9600 | CS8 | CREAD | HUPCL | CLOCAL)
+#define	DEFAULT_LFLAGS	(ISIG | ICANON | ECHO | ECHOE | ECHOK | \
+			ECHOCTL | ECHOKE | IEXTEN)
+
+#ifndef _POSIX_VDISABLE
+#define   _POSIX_VDISABLE '\0'
+#endif
+
+#define SNIFF_MAX	65536		/* Sniff buffer size (2^n) */
+#define SNIFF_MASK	(SNIFF_MAX - 1)	/* Sniff wrap mask */
+
+#define VPDSIZE (512)
+
+/*
+ * Lock function/defines.
+ * Makes spotting lock/unlock locations easier.
+ */
+# define DGAP_SPINLOCK_INIT(x)		spin_lock_init(&(x))
+# define DGAP_LOCK(x,y)			spin_lock_irqsave(&(x), y)
+# define DGAP_UNLOCK(x,y)		spin_unlock_irqrestore(&(x), y)
+# define DGAP_TRYLOCK(x,y)		spin_trylock(&(x))
+
+/*
+ * All the possible states the driver can be while being loaded.
+ */
+enum {
+	DRIVER_INITIALIZED = 0,
+	DRIVER_NEED_CONFIG_LOAD,
+	DRIVER_REQUESTED_CONFIG,
+	DRIVER_READY
+};
+
+/*
+ * All the possible states the board can be while booting up.
+ */
+enum {
+	BOARD_FAILED = 0,
+	CONFIG_NOT_FOUND,
+	BOARD_FOUND,
+	NEED_RESET,
+	FINISHED_RESET,
+	NEED_CONFIG,
+	FINISHED_CONFIG,
+	NEED_DEVICE_CREATION,
+	REQUESTED_DEVICE_CREATION,
+	FINISHED_DEVICE_CREATION,
+	NEED_BIOS_LOAD,
+	REQUESTED_BIOS,
+	WAIT_BIOS_LOAD,
+	FINISHED_BIOS_LOAD,
+	NEED_FEP_LOAD,
+	REQUESTED_FEP,
+	WAIT_FEP_LOAD,
+	FINISHED_FEP_LOAD,
+	NEED_PROC_CREATION,
+	FINISHED_PROC_CREATION,
+	BOARD_READY
+};
+
+/*
+ * All the possible states that a requested concentrator image can be in.
+ */
+enum {
+	NO_PENDING_CONCENTRATOR_REQUESTS = 0,
+	NEED_CONCENTRATOR,
+	REQUESTED_CONCENTRATOR
+};
+
+extern char *dgap_state_text[];
+extern char *dgap_driver_state_text[];
+
+
+/* 
+ * Modem line constants are defined as macros because DSR and
+ * DCD are swapable using the ditty altpin option.
+ */
+#define D_CD(ch)        ch->ch_cd       /* Carrier detect       */
+#define D_DSR(ch)       ch->ch_dsr      /* Data set ready       */
+#define D_RTS(ch)       DM_RTS          /* Request to send      */
+#define D_CTS(ch)       DM_CTS          /* Clear to send        */
+#define D_RI(ch)        DM_RI           /* Ring indicator       */
+#define D_DTR(ch)       DM_DTR          /* Data terminal ready  */
+
+
+/*************************************************************************
+ *
+ * Structures and closely related defines.
+ *
+ *************************************************************************/
+
+
+/*
+ * A structure to hold a statistics counter.  We also
+ * compute moving averages for this counter.
+ */
+struct macounter
+{
+	u32		cnt;	/* Total count */
+	ulong		accum;	/* Acuumulator per period */
+	ulong		sma;	/* Simple moving average */
+	ulong		ema;	/* Exponential moving average */
+};
+
+
+/************************************************************************ 
+ * Device flag definitions for bd_flags.
+ ************************************************************************/
+#define	BD_FEP5PLUS	0x0001          /* Supports FEP5 Plus commands */
+#define BD_HAS_VPD	0x0002		/* Board has VPD info available */
+
+
+/*
+ *	Per-board information
+ */
+struct board_t
+{
+	int		magic;		/* Board Magic number.  */
+	int		boardnum;	/* Board number: 0-3 */
+	int		firstminor;	/* First minor, e.g. 0, 30, 60 */
+
+	int		type;		/* Type of board */
+	char		*name;		/* Product Name */
+	struct pci_dev	*pdev;		/* Pointer to the pci_dev struct */ 
+	u16		vendor;		/* PCI vendor ID */
+	u16		device;		/* PCI device ID */
+	u16		subvendor;	/* PCI subsystem vendor ID */
+	u16		subdevice;	/* PCI subsystem device ID */
+	uchar		rev;		/* PCI revision ID */
+	uint		pci_bus;	/* PCI bus value */
+	uint		pci_slot;	/* PCI slot value */
+	u16		maxports;	/* MAX ports this board can handle */
+	uchar		vpd[VPDSIZE];	/* VPD of board, if found */
+	u32		bd_flags;	/* Board flags */
+
+	spinlock_t	bd_lock;	/* Used to protect board */
+
+	u32		state;		/* State of card. */
+	wait_queue_head_t state_wait;	/* Place to sleep on for state change */
+
+	struct		tasklet_struct helper_tasklet; /* Poll helper tasklet */
+
+	u32		wait_for_bios;
+	u32		wait_for_fep;
+
+	struct cnode *  bd_config;	/* Config of board */
+
+	u16		nasync;		/* Number of ports on card */
+
+	u32		use_interrupts;	/* Should we be interrupt driven? */
+	ulong		irq;		/* Interrupt request number */
+	ulong		intr_count;	/* Count of interrupts */
+	u32		intr_used;	/* Non-zero if using interrupts */
+	u32		intr_running;	/* Non-zero if FEP knows its doing interrupts */
+
+	ulong		port;		/* Start of base io port of the card */
+	ulong		port_end;	/* End of base io port of the card */
+	ulong		membase;	/* Start of base memory of the card */
+	ulong		membase_end;	/* End of base memory of the card */
+
+	uchar 		*re_map_port;	/* Remapped io port of the card */
+	uchar		*re_map_membase;/* Remapped memory of the card */
+
+	uchar		runwait;	/* # Processes waiting for FEP  */
+	uchar		inhibit_poller; /* Tells  the poller to leave us alone */
+
+	struct channel_t *channels[MAXPORTS]; /* array of pointers to our channels. */
+
+	struct tty_driver	*SerialDriver;
+	char		SerialName[200];
+	struct tty_driver	*PrintDriver;
+	char		PrintName[200];
+
+	u32		dgap_Major_Serial_Registered;
+	u32		dgap_Major_TransparentPrint_Registered;
+
+	u32		dgap_Serial_Major;
+	u32		dgap_TransparentPrint_Major;
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28)
+	u32		TtyRefCnt;
+#endif
+
+	struct bs_t	*bd_bs;			/* Base structure pointer       */
+
+	char	*flipbuf;		/* Our flip buffer, alloced if board is found */
+	char	*flipflagbuf;		/* Our flip flag buffer, alloced if board is found */
+
+	u16		dpatype;	/* The board "type", as defined by DPA */
+	u16		dpastatus;	/* The board "status", as defined by DPA */
+	wait_queue_head_t kme_wait;	/* Needed for DPA support */
+
+	u32		conc_dl_status;	/* Status of any pending conc download */
+	/*
+	 *	Mgmt data.
+	 */
+        char		*msgbuf_head;
+        char		*msgbuf;
+};
+
+
+
+/************************************************************************ 
+ * Unit flag definitions for un_flags.
+ ************************************************************************/
+#define UN_ISOPEN	0x0001		/* Device is open		*/
+#define UN_CLOSING	0x0002		/* Line is being closed		*/
+#define UN_IMM		0x0004		/* Service immediately		*/
+#define UN_BUSY		0x0008		/* Some work this channel	*/
+#define UN_BREAKI	0x0010		/* Input break received		*/
+#define UN_PWAIT	0x0020		/* Printer waiting for terminal	*/
+#define UN_TIME		0x0040		/* Waiting on time		*/
+#define UN_EMPTY	0x0080		/* Waiting output queue empty	*/
+#define UN_LOW		0x0100		/* Waiting output low water mark*/
+#define UN_EXCL_OPEN	0x0200		/* Open for exclusive use	*/
+#define UN_WOPEN	0x0400		/* Device waiting for open	*/
+#define UN_WIOCTL	0x0800		/* Device waiting for open	*/
+#define UN_HANGUP	0x8000		/* Carrier lost			*/
+
+struct device;
+
+/************************************************************************
+ * Structure for terminal or printer unit. 
+ ************************************************************************/
+struct un_t {
+	int	magic;		/* Unit Magic Number.			*/
+	struct	channel_t *un_ch;
+	u32	un_time;
+	u32	un_type;
+	u32	un_open_count;	/* Counter of opens to port		*/
+	struct tty_struct *un_tty;/* Pointer to unit tty structure	*/
+	u32	un_flags;	/* Unit flags				*/
+	wait_queue_head_t un_flags_wait; /* Place to sleep to wait on unit */
+	u32	un_dev;		/* Minor device number			*/
+	tcflag_t un_oflag;	/* oflags being done on board		*/
+	tcflag_t un_lflag;	/* lflags being done on board		*/
+	struct device *un_sysfs;
+};
+
+
+/************************************************************************ 
+ * Device flag definitions for ch_flags.
+ ************************************************************************/
+#define CH_PRON         0x0001          /* Printer on string                */
+#define CH_OUT          0x0002          /* Dial-out device open             */
+#define CH_STOP         0x0004          /* Output is stopped                */
+#define CH_STOPI        0x0008          /* Input is stopped                 */
+#define CH_CD           0x0010          /* Carrier is present               */
+#define CH_FCAR         0x0020          /* Carrier forced on                */
+
+#define CH_RXBLOCK      0x0080          /* Enable rx blocked flag           */
+#define CH_WLOW         0x0100          /* Term waiting low event           */
+#define CH_WEMPTY       0x0200          /* Term waiting empty event         */
+#define CH_RENABLE      0x0400          /* Buffer just emptied          */
+#define CH_RACTIVE      0x0800          /* Process active in xxread()   */
+#define CH_RWAIT        0x1000          /* Process waiting in xxread()  */
+#define CH_BAUD0	0x2000		/* Used for checking B0 transitions */
+#define CH_HANGUP       0x8000		/* Hangup received                  */
+
+/*
+ * Definitions for ch_sniff_flags
+ */
+#define SNIFF_OPEN	0x1
+#define SNIFF_WAIT_DATA	0x2
+#define SNIFF_WAIT_SPACE 0x4
+
+
+/************************************************************************ 
+ * Channel information structure.
+ ************************************************************************/
+struct channel_t {
+	int magic;			/* Channel Magic Number		*/
+	struct bs_t	*ch_bs;		/* Base structure pointer       */
+	struct cm_t	*ch_cm;		/* Command queue pointer        */
+	struct board_t *ch_bd;		/* Board structure pointer      */
+	unsigned char *ch_vaddr;	/* FEP memory origin            */
+	unsigned char *ch_taddr;	/* Write buffer origin          */
+	unsigned char *ch_raddr;	/* Read buffer origin           */
+	struct digi_t  ch_digi;		/* Transparent Print structure  */
+	struct un_t ch_tun;		/* Terminal unit info           */
+	struct un_t ch_pun;		/* Printer unit info            */
+
+	spinlock_t	ch_lock;	/* provide for serialization */
+	wait_queue_head_t ch_flags_wait;
+
+	u32	pscan_state;
+	uchar	pscan_savechar;
+
+	u32 ch_portnum;			/* Port number, 0 offset.	*/
+	u32 ch_open_count;		/* open count			*/
+	u32	ch_flags;		/* Channel flags                */
+
+
+	u32	ch_close_delay;		/* How long we should drop RTS/DTR for */
+
+	u32	ch_cpstime;		/* Time for CPS calculations    */
+
+	tcflag_t ch_c_iflag;		/* channel iflags               */
+	tcflag_t ch_c_cflag;		/* channel cflags               */
+	tcflag_t ch_c_oflag;		/* channel oflags               */
+	tcflag_t ch_c_lflag;		/* channel lflags               */
+
+	u16  ch_fepiflag;            /* FEP tty iflags               */
+	u16  ch_fepcflag;		/* FEP tty cflags               */
+	u16  ch_fepoflag;		/* FEP tty oflags               */
+	u16  ch_wopen;			/* Waiting for open process cnt */
+	u16  ch_tstart;			/* Transmit buffer start        */
+	u16  ch_tsize;			/* Transmit buffer size         */
+	u16  ch_rstart;			/* Receive buffer start         */
+	u16  ch_rsize;			/* Receive buffer size          */
+	u16  ch_rdelay;			/* Receive delay time           */
+
+	u16	ch_tlw;			/* Our currently set low water mark */
+
+	u16  ch_cook;			/* Output character mask        */
+
+	uchar   ch_card;		/* Card channel is on           */
+	uchar   ch_stopc;		/* Stop character               */
+	uchar   ch_startc;		/* Start character              */
+
+	uchar   ch_mostat;		/* FEP output modem status      */
+	uchar   ch_mistat;		/* FEP input modem status       */
+	uchar   ch_mforce;		/* Modem values to be forced    */
+	uchar   ch_mval;		/* Force values                 */
+	uchar   ch_fepstopc;		/* FEP stop character           */
+	uchar   ch_fepstartc;		/* FEP start character          */
+
+	uchar   ch_astopc;		/* Auxiliary Stop character     */
+	uchar   ch_astartc;		/* Auxiliary Start character    */
+	uchar   ch_fepastopc;		/* Auxiliary FEP stop char      */
+	uchar   ch_fepastartc;		/* Auxiliary FEP start char     */
+
+	uchar   ch_hflow;		/* FEP hardware handshake       */
+	uchar   ch_dsr;			/* stores real dsr value        */
+	uchar   ch_cd;			/* stores real cd value         */
+	uchar   ch_tx_win;		/* channel tx buffer window     */
+	uchar   ch_rx_win;		/* channel rx buffer window     */
+	uint	ch_custom_speed;	/* Custom baud, if set		*/
+	uint	ch_baud_info;		/* Current baud info for /proc output	*/
+	ulong	ch_rxcount;		/* total of data received so far	*/
+	ulong	ch_txcount;		/* total of data transmitted so far	*/
+	ulong	ch_err_parity;		/* Count of parity errors on channel	*/
+	ulong	ch_err_frame;		/* Count of framing errors on channel	*/
+	ulong	ch_err_break;		/* Count of breaks on channel	*/
+	ulong	ch_err_overrun;		/* Count of overruns on channel	*/
+
+	uint ch_sniff_in;
+	uint ch_sniff_out;
+	char *ch_sniff_buf;		/* Sniff buffer for proc */
+	ulong ch_sniff_flags;		/* Channel flags                */
+	wait_queue_head_t ch_sniff_wait;
+};
+
+
+/*************************************************************************
+ *
+ * Prototypes for non-static functions used in more than one module
+ *
+ *************************************************************************/
+
+extern int		dgap_ms_sleep(ulong ms);
+extern void		*dgap_driver_kzmalloc(size_t size, int priority);
+extern char		*dgap_ioctl_name(int cmd);
+
+/*
+ * Our Global Variables.
+ */
+extern int		dgap_driver_state;	/* The state of the driver	*/
+extern int		dgap_debug;		/* Debug variable		*/
+extern int		dgap_rawreadok;		/* Set if user wants rawreads	*/
+extern int		dgap_poll_tick;		/* Poll interval - 20 ms	*/
+extern spinlock_t	dgap_global_lock;	/* Driver global spinlock	*/
+extern uint		dgap_NumBoards;		/* Total number of boards	*/
+extern struct board_t	*dgap_Board[MAXBOARDS];	/* Array of board structs	*/
+extern ulong		dgap_poll_counter;	/* Times the poller has run	*/
+extern char		*dgap_config_buf;	/* The config file buffer	*/
+extern spinlock_t	dgap_dl_lock;		/* Downloader spinlock		*/
+extern wait_queue_head_t dgap_dl_wait;		/* Wait queue for downloader	*/
+extern int		dgap_dl_action;		/* Action flag for downloader	*/
+extern int		dgap_registerttyswithsysfs; /* Should we register the	*/
+						    /* ttys with sysfs or not	*/
+						    
+/*
+ * Functions from dgap_parsefile
+ */						    
+extern int dgap_parsefile(char **in, int Remove);
+extern struct cnode *dgap_find_config(int type, int bus, int slot);
+extern uint dgap_config_get_number_of_ports(struct board_t *bd);
+extern char *dgap_create_config_string(struct board_t *bd, char *string);
+extern char *dgap_get_config_letters(struct board_t *bd, char *string);
+extern uint dgap_config_get_useintr(struct board_t *bd);
+extern uint dgap_config_get_altpin(struct board_t *bd);						    
+
+/*
+ * Global functions declared in dgap_fep5.c, but must be hidden from
+ * user space programs.
+ */
+extern void	dgap_poll_tasklet(unsigned long data); 
+extern void	dgap_cmdb(struct channel_t *ch, uchar cmd, uchar byte1, uchar byte2, uint ncmds);
+extern void	dgap_cmdw(struct channel_t *ch, uchar cmd, u16 word, uint ncmds);
+extern void	dgap_wmove(struct channel_t *ch, char *buf, uint cnt);
+extern int	dgap_param(struct tty_struct *tty);
+extern void	dgap_parity_scan(struct channel_t *ch, unsigned char *cbuf, unsigned char *fbuf, int *len);
+extern uint	dgap_get_custom_baud(struct channel_t *ch);
+extern void	dgap_firmware_reset_port(struct channel_t *ch);
+
+/*
+ * Functions prototypes from dgap_tty.h
+ */
+int	dgap_tty_register(struct board_t *brd);
+
+int	dgap_tty_preinit(void);
+int     dgap_tty_init(struct board_t *);
+
+void	dgap_tty_post_uninit(void);
+void	dgap_tty_uninit(struct board_t *);
+
+void	dgap_carrier(struct channel_t *ch);
+void	dgap_input(struct channel_t *ch);
+
+/************************************************************************* 
+ ***	FEP Version 5 dependent definitions
+ ************************************************************************/
+
+/************************************************************************
+ *      FEP memory offsets
+ ************************************************************************/
+#define START           0x0004L         /* Execution start address      */
+
+#define CMDBUF          0x0d10L         /* Command (cm_t) structure offset */
+#define CMDSTART        0x0400L         /* Start of command buffer      */   
+#define CMDMAX          0x0800L         /* End of command buffer        */
+
+#define EVBUF           0x0d18L         /* Event (ev_t) structure       */
+#define EVSTART         0x0800L         /* Start of event buffer        */
+#define EVMAX           0x0c00L         /* End of event buffer          */
+#define FEP5_PLUS       0x0E40          /* ASCII '5' and ASCII 'A' is here  */
+#define ECS_SEG         0x0E44          /* Segment of the extended channel structure */
+#define LINE_SPEED      0x10            /* Offset into ECS_SEG for line speed   */
+                                        /* if the fep has extended capabilities */
+
+/* BIOS MAGIC SPOTS */
+#define ERROR           0x0C14L		/* BIOS error code              */
+#define SEQUENCE	0x0C12L		/* BIOS sequence indicator      */
+#define POSTAREA	0x0C00L		/* POST complete message area   */
+
+/* FEP MAGIC SPOTS */
+#define FEPSTAT         POSTAREA        /* OS here when FEP comes up    */
+#define NCHAN           0x0C02L         /* number of ports FEP sees     */
+#define PANIC           0x0C10L         /* PANIC area for FEP           */
+#define KMEMEM          0x0C30L         /* Memory for KME use           */   
+#define CONFIG          0x0CD0L         /* Concentrator configuration info */
+#define CONFIGSIZE      0x0030          /* configuration info size      */
+#define DOWNREQ         0x0D00          /* Download request buffer pointer */
+
+#define CHANBUF         0x1000L         /* Async channel (bs_t) structs */
+#define FEPOSSIZE       0x1FFF          /* 8K FEPOS                     */
+
+#define XEMPORTS    0xC02	/*
+				 * Offset in board memory where FEP5 stores
+				 * how many ports it has detected.
+				 * NOTE: FEP5 reports 64 ports when the user
+				 * has the cable in EBI OUT instead of EBI IN.
+				 */
+
+#define FEPCLR      0x00
+#define FEPMEM      0x02 
+#define FEPRST      0x04 
+#define FEPINT      0x08
+#define FEPMASK     0x0e
+#define FEPWIN      0x80
+
+#define LOWMEM      0x0100
+#define HIGHMEM     0x7f00
+
+#define FEPTIMEOUT 200000
+
+#define ENABLE_INTR		0x0e04		/* Enable interrupts flag */
+#define FEPPOLL_MIN		1		/* minimum of 1 millisecond */  
+#define FEPPOLL_MAX		20		/* maximum of 20 milliseconds */
+#define FEPPOLL			0x0c26		/* Fep event poll interval */   
+
+#define	IALTPIN			0x0080		/* Input flag to swap DSR <-> DCD */
+
+/************************************************************************ 
+ * Command structure definition.
+ ************************************************************************/
+struct cm_t {
+	volatile unsigned short cm_head;	/* Command buffer head offset	*/
+	volatile unsigned short cm_tail;	/* Command buffer tail offset	*/
+	volatile unsigned short cm_start;	/* start offset of buffer	*/
+	volatile unsigned short cm_max;		/* last offset of buffer	*/
+};
+
+/************************************************************************
+ * Event structure definition.
+ ************************************************************************/
+struct ev_t {
+	volatile unsigned short ev_head;	/* Command buffer head offset	*/
+	volatile unsigned short ev_tail;	/* Command buffer tail offset	*/
+	volatile unsigned short ev_start;	/* start offset of buffer	*/
+	volatile unsigned short ev_max;		/* last offset of buffer	*/
+};
+
+/************************************************************************
+ * Download buffer structure.
+ ************************************************************************/
+struct downld_t {
+	uchar	dl_type;		/* Header                       */
+	uchar	dl_seq;			/* Download sequence            */
+	ushort	dl_srev;		/* Software revision number     */
+	ushort	dl_lrev;		/* Low revision number          */
+	ushort	dl_hrev;		/* High revision number         */
+	ushort	dl_seg;			/* Start segment address        */
+	ushort	dl_size;		/* Number of bytes to download  */
+	uchar	dl_data[1024];		/* Download data                */
+};
+
+/************************************************************************ 
+ * Per channel buffer structure
+ ************************************************************************
+ *              Base Structure Entries Usage Meanings to Host           * 
+ *                                                                      * 
+ *        W = read write        R = read only                           * 
+ *        C = changed by commands only                                  * 
+ *        U = unknown (may be changed w/o notice)                       *
+ ************************************************************************/
+struct bs_t {
+	volatile unsigned short  tp_jmp;	/* Transmit poll jump		 */
+	volatile unsigned short  tc_jmp;	/* Cooked procedure jump	 */
+	volatile unsigned short  ri_jmp;	/* Not currently used		 */
+	volatile unsigned short  rp_jmp;	/* Receive poll jump		 */
+
+	volatile unsigned short  tx_seg;	/* W  Tx segment	 */
+	volatile unsigned short  tx_head;	/* W  Tx buffer head offset	*/
+	volatile unsigned short  tx_tail;	/* R  Tx buffer tail offset	*/
+	volatile unsigned short  tx_max;	/* W  Tx buffer size - 1	 */
+ 
+	volatile unsigned short  rx_seg;	/* W  Rx segment		*/
+	volatile unsigned short  rx_head;	/* W  Rx buffer head offset	*/
+	volatile unsigned short  rx_tail;	/* R  Rx buffer tail offset	*/
+	volatile unsigned short  rx_max;	/* W  Rx buffer size - 1	 */
+
+	volatile unsigned short  tx_lw;		/* W  Tx buffer low water mark  */
+	volatile unsigned short  rx_lw;		/* W  Rx buffer low water mark  */
+	volatile unsigned short  rx_hw;		/* W  Rx buffer high water mark */
+	volatile unsigned short  incr;		/* W  Increment to next channel */
+
+	volatile unsigned short  fepdev;	/* U  SCC device base address    */
+	volatile unsigned short  edelay;	/* W  Exception delay            */
+	volatile unsigned short  blen;		/* W  Break length              */
+	volatile unsigned short  btime;		/* U  Break complete time       */
+
+	volatile unsigned short  iflag;		/* C  UNIX input flags          */
+	volatile unsigned short  oflag;		/* C  UNIX output flags         */
+	volatile unsigned short  cflag;		/* C  UNIX control flags        */
+	volatile unsigned short  wfill[13];	/* U  Reserved for expansion    */
+
+	volatile unsigned char   num;		/* U  Channel number            */
+	volatile unsigned char   ract;		/* U  Receiver active counter   */
+	volatile unsigned char   bstat;		/* U  Break status bits         */
+	volatile unsigned char   tbusy;		/* W  Transmit busy             */
+	volatile unsigned char   iempty;	/* W  Transmit empty event enable */
+	volatile unsigned char   ilow;		/* W  Transmit low-water event enable */
+	volatile unsigned char   idata;		/* W  Receive data interrupt enable */
+	volatile unsigned char   eflag;		/* U  Host event flags          */
+
+	volatile unsigned char   tflag;		/* U  Transmit flags            */
+	volatile unsigned char   rflag;		/* U  Receive flags             */
+	volatile unsigned char   xmask;		/* U  Transmit ready flags      */
+	volatile unsigned char   xval;		/* U  Transmit ready value      */
+	volatile unsigned char   m_stat;	/* RC Modem status bits          */
+	volatile unsigned char   m_change;	/* U  Modem bits which changed  */
+	volatile unsigned char   m_int;		/* W  Modem interrupt enable bits */
+	volatile unsigned char   m_last;	/* U  Last modem status         */
+
+	volatile unsigned char   mtran;		/* C   Unreported modem trans   */
+	volatile unsigned char   orun;		/* C   Buffer overrun occurred  */
+	volatile unsigned char   astartc;	/* W   Auxiliary Xon char       */  
+	volatile unsigned char   astopc;	/* W   Auxiliary Xoff char      */
+	volatile unsigned char   startc;	/* W   Xon character             */
+	volatile unsigned char   stopc;		/* W   Xoff character           */
+	volatile unsigned char   vnextc;	/* W   Vnext character           */
+	volatile unsigned char   hflow;		/* C   Software flow control    */
+
+	volatile unsigned char   fillc;		/* U   Delay Fill character     */
+	volatile unsigned char   ochar;		/* U   Saved output character   */
+	volatile unsigned char   omask;		/* U   Output character mask    */
+
+	volatile unsigned char   bfill[13];	/* U   Reserved for expansion   */  
+
+	volatile unsigned char   scc[16];	/* U   SCC registers            */
+};
+
+
+/************************************************************************   
+ * FEP supported functions
+ ************************************************************************/
+#define SRLOW		0xe0		/* Set receive low water	*/
+#define SRHIGH		0xe1		/* Set receive high water	*/
+#define FLUSHTX		0xe2		/* Flush transmit buffer	*/
+#define PAUSETX		0xe3		/* Pause data transmission	*/
+#define RESUMETX	0xe4		/* Resume data transmission	*/
+#define SMINT		0xe5		/* Set Modem Interrupt		*/
+#define SAFLOWC		0xe6		/* Set Aux. flow control chars	*/
+#define SBREAK		0xe8		/* Send break			*/
+#define SMODEM		0xe9		/* Set 8530 modem control lines	*/  
+#define SIFLAG		0xea		/* Set UNIX iflags		*/
+#define SFLOWC		0xeb		/* Set flow control characters	*/
+#define STLOW		0xec		/* Set transmit low water mark	*/
+#define RPAUSE		0xee		/* Pause receive		*/
+#define RRESUME		0xef		/* Resume receive		*/  
+#define CHRESET		0xf0		/* Reset Channel		*/
+#define BUFSETALL	0xf2		/* Set Tx & Rx buffer size avail*/
+#define SOFLAG		0xf3		/* Set UNIX oflags		*/
+#define SHFLOW		0xf4		/* Set hardware handshake	*/
+#define SCFLAG		0xf5		/* Set UNIX cflags		*/
+#define SVNEXT		0xf6		/* Set VNEXT character		*/
+#define SPINTFC		0xfc		/* Reserved			*/
+#define SCOMMODE	0xfd		/* Set RS232/422 mode		*/
+
+
+/************************************************************************ 
+ *	Modes for SCOMMODE
+ ************************************************************************/
+#define MODE_232	0x00
+#define MODE_422	0x01
+
+
+/************************************************************************ 
+ *      Event flags.
+ ************************************************************************/
+#define IFBREAK         0x01            /* Break received               */  
+#define IFTLW           0x02            /* Transmit low water           */
+#define IFTEM           0x04            /* Transmitter empty            */
+#define IFDATA          0x08            /* Receive data present         */
+#define IFMODEM         0x20            /* Modem status change          */
+
+/************************************************************************   
+ *      Modem flags
+ ************************************************************************/
+#       define  DM_RTS          0x02    /* Request to send              */
+#       define  DM_CD           0x80    /* Carrier detect               */
+#       define  DM_DSR          0x20    /* Data set ready               */
+#       define  DM_CTS          0x10    /* Clear to send                */
+#       define  DM_RI           0x40    /* Ring indicator               */
+#       define  DM_DTR          0x01    /* Data terminal ready          */
+
+
+/************************************************************************
+ * Stuf from dgap_conf.h
+ ************************************************************************/
+
+#define NULLNODE 0		/* header node, not used */
+#define BNODE 1			/* Board node */
+#define LNODE 2			/* Line node */
+#define CNODE 3			/* Concentrator node */
+#define MNODE 4			/* EBI Module node */
+#define TNODE 5			/* tty name prefix node */
+#define	CUNODE 6		/* cu name prefix (non-SCO) */
+#define PNODE 7			/* trans. print prefix node */
+#define JNODE 8			/* maJor number node */
+#define ANODE 9			/* altpin */
+#define	TSNODE 10		/* tty structure size */
+#define CSNODE 11		/* channel structure size */
+#define BSNODE 12		/* board structure size */
+#define USNODE 13		/* unit schedule structure size */
+#define FSNODE 14		/* f2200 structure size */
+#define VSNODE 15		/* size of VPIX structures */
+#define INTRNODE 16		/* enable interrupt */
+
+/* Enumeration of tokens */
+#define	BEGIN	1
+#define	END	2
+#define	BOARD	10
+
+#define EPCFS	11 /* start of EPC family definitions */
+#define	ICX		11
+#define	MCX		13
+#define PCX	14
+#define	IEPC	15
+#define	EEPC	16
+#define	MEPC	17
+#define	IPCM	18
+#define	EPCM	19
+#define	MPCM	20
+#define PEPC	21
+#define PPCM	22
+#ifdef CP
+#define ICP     23
+#define ECP     24
+#define MCP     25
+#endif
+#define EPCFE	25 /* end of EPC family definitions */
+#define	PC2E	26
+#define	PC4E	27
+#define	PC4E8K	28
+#define	PC8E	29
+#define	PC8E8K	30
+#define	PC16E	31
+#define MC2E8K  34
+#define MC4E8K  35
+#define MC8E8K  36
+
+#define AVANFS	42	/* start of Avanstar family definitions */
+#define A8P 	42
+#define A16P	43
+#define AVANFE	43	/* end of Avanstar family definitions */
+
+#define DA2000FS	44	/* start of AccelePort 2000 family definitions */
+#define DA22 		44 /* AccelePort 2002 */
+#define DA24 		45 /* AccelePort 2004 */
+#define DA28		46 /* AccelePort 2008 */
+#define DA216		47 /* AccelePort 2016 */
+#define DAR4		48 /* AccelePort RAS 4 port */
+#define DAR8		49 /* AccelePort RAS 8 port */
+#define DDR24		50 /* DataFire RAS 24 port */
+#define DDR30		51 /* DataFire RAS 30 port */
+#define DDR48		52 /* DataFire RAS 48 port */
+#define DDR60		53 /* DataFire RAS 60 port */
+#define DA2000FE	53 /* end of AccelePort 2000/RAS family definitions */
+
+#define PCXRFS	106	/* start of PCXR family definitions */
+#define	APORT4	106
+#define	APORT8	107
+#define PAPORT4 108
+#define PAPORT8 109
+#define APORT4_920I	110
+#define APORT8_920I	111
+#define APORT4_920P	112
+#define APORT8_920P	113
+#define APORT2_920P 114
+#define PCXRFE	117	/* end of PCXR family definitions */
+
+#define	LINE	82
+#ifdef T1
+#define T1M	83
+#define E1M	84
+#endif
+#define	CONC	64
+#define	CX	65
+#define	EPC	66
+#define	MOD	67
+#define	PORTS	68
+#define METHOD	69
+#define CUSTOM	70
+#define BASIC	71
+#define STATUS	72
+#define MODEM	73
+/* The following tokens can appear in multiple places */
+#define	SPEED	74
+#define	NPORTS	75
+#define	ID	76
+#define CABLE	77
+#define CONNECT	78
+#define	IO	79
+#define	MEM	80
+#define DPSZ	81
+
+#define	TTYN	90
+#define	CU	91
+#define	PRINT	92
+#define	XPRINT	93
+#define CMAJOR   94 
+#define ALTPIN  95
+#define STARTO 96
+#define USEINTR  97
+#define PCIINFO  98
+
+#define	TTSIZ	100
+#define	CHSIZ	101
+#define BSSIZ	102
+#define	UNTSIZ	103
+#define	F2SIZ	104
+#define	VPSIZ	105
+
+#define	TOTAL_BOARD	2
+#define	CURRENT_BRD	4
+#define	BOARD_TYPE	6
+#define	IO_ADDRESS	8
+#define	MEM_ADDRESS	10
+
+#define	FIELDS_PER_PAGE	18
+
+#define TB_FIELD	1
+#define CB_FIELD	3
+#define BT_FIELD	5
+#define IO_FIELD	7
+#define ID_FIELD	8
+#define ME_FIELD	9
+#define TTY_FIELD	11
+#define CU_FIELD	13
+#define PR_FIELD	15
+#define MPR_FIELD	17
+
+#define	MAX_FIELD	512
+
+#define	INIT		0
+#define	NITEMS		128
+#define MAX_ITEM	512
+
+#define	DSCRINST	1
+#define	DSCRNUM		3
+#define	ALTPINQ		5
+#define	SSAVE		7
+
+#define	DSCR		"32"
+#define	ONETONINE	"123456789"
+#define	ALL		"1234567890"
+
+
+struct cnode {
+	struct cnode *next;
+	int type;
+	int numbrd;
+
+	union {
+		struct {
+			char  type;	/* Board Type 		*/
+			short port;	/* I/O Address		*/
+			char  *portstr; /* I/O Address in string */
+			long  addr;	/* Memory Address	*/
+			char  *addrstr; /* Memory Address in string */
+			long  pcibus;	/* PCI BUS		*/
+			char  *pcibusstr; /* PCI BUS in string */
+			long  pcislot;	/* PCI SLOT		*/
+			char  *pcislotstr; /* PCI SLOT in string */
+			char  nport;	/* Number of Ports	*/
+			char  *id;	/* tty id		*/
+			int   start;	/* start of tty counting */
+			char  *method;  /* Install method       */
+			char  v_type;
+			char  v_port;
+			char  v_addr;
+			char  v_pcibus;
+			char  v_pcislot;
+			char  v_nport;
+			char  v_id;
+			char  v_start;
+			char  v_method;
+			char  line1;
+			char  line2;
+			char  conc1;   /* total concs in line1 */
+			char  conc2;   /* total concs in line2 */
+			char  module1; /* total modules for line1 */
+			char  module2; /* total modules for line2 */
+			char  *status; /* config status */
+			char  *dimstatus;	 /* Y/N */
+			int   status_index; /* field pointer */
+		} board;
+
+		struct {
+			char  *cable;
+			char  v_cable;
+			char  speed;
+			char  v_speed;
+		} line;
+
+		struct {
+			char  type;
+			char  *connect;
+			char  speed;
+			char  nport;
+			char  *id;
+			char  *idstr;
+			int   start;
+			char  v_type;
+			char  v_connect;
+			char  v_speed;
+			char  v_nport;
+			char  v_id;
+			char  v_start;
+		} conc;
+
+		struct {
+			char type;
+			char nport;
+			char *id;
+			char *idstr;
+			int  start;
+			char v_type;
+			char v_nport;
+			char v_id;
+			char v_start;
+		} module;
+
+		char *ttyname;
+		
+		char *cuname;
+		
+		char *printname;
+
+		int  majornumber;
+
+		int  altpin;
+
+		int  ttysize;
+
+		int  chsize;
+
+		int  bssize;
+
+		int  unsize;
+
+		int  f2size;
+
+		int  vpixsize;
+
+		int  useintr;
+	} u;
+};
+
+#endif
diff -urpN linux-3.13.1-orig/drivers/staging/dgap/Makefile linux-3.13.1-new/drivers/staging/dgap/Makefile
--- linux-3.13.1-orig/drivers/staging/dgap/Makefile	2014-02-11 09:50:14.808691007 -0500
+++ linux-3.13.1-new/drivers/staging/dgap/Makefile	2014-02-11 10:38:57.995190837 -0500
@@ -1,4 +1,2 @@
 obj-$(CONFIG_DGAP) += dgap.o
 
-dgap-objs :=	dgap_driver.o  
-
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel




[Index of Archives]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux