Tidy up the multi-line comments at the beginning of the file to follow the CodingStyle. Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx> Cc: Ian Abbott <abbotti@xxxxxxxxx> Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> --- drivers/staging/comedi/drivers/pcmda12.c | 93 ++++++++++++++++---------------- 1 file changed, 47 insertions(+), 46 deletions(-) diff --git a/drivers/staging/comedi/drivers/pcmda12.c b/drivers/staging/comedi/drivers/pcmda12.c index 8ad2479..774a63d 100644 --- a/drivers/staging/comedi/drivers/pcmda12.c +++ b/drivers/staging/comedi/drivers/pcmda12.c @@ -1,51 +1,52 @@ /* - comedi/drivers/pcmda12.c - Driver for Winsystems PC-104 based PCM-D/A-12 8-channel AO board. - - COMEDI - Linux Control and Measurement Device Interface - Copyright (C) 2006 Calin A. Culianu <calin@xxxxxxxxx> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. -*/ + * pcmda12.c + * Driver for Winsystems PC-104 based PCM-D/A-12 8-channel AO board. + * + * COMEDI - Linux Control and Measurement Device Interface + * Copyright (C) 2006 Calin A. Culianu <calin@xxxxxxxxx> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + /* -Driver: pcmda12 -Description: A driver for the Winsystems PCM-D/A-12 -Devices: [Winsystems] PCM-D/A-12 (pcmda12) -Author: Calin Culianu <calin@xxxxxxxxx> -Updated: Fri, 13 Jan 2006 12:01:01 -0500 -Status: works - -A driver for the relatively straightforward-to-program PCM-D/A-12. -This board doesn't support commands, and the only way to set its -analog output range is to jumper the board. As such, -comedi_data_write() ignores the range value specified. - -The board uses 16 consecutive I/O addresses starting at the I/O port -base address. Each address corresponds to the LSB then MSB of a -particular channel from 0-7. - -Note that the board is not ISA-PNP capable and thus -needs the I/O port comedi_config parameter. - -Note that passing a nonzero value as the second config option will -enable "simultaneous xfer" mode for this board, in which AO writes -will not take effect until a subsequent read of any AO channel. This -is so that one can speed up programming by preloading all AO registers -with values before simultaneously setting them to take effect with one -read command. - -Configuration Options: - [0] - I/O port base address - [1] - Do Simultaneous Xfer (see description) -*/ + * Driver: pcmda12 + * Description: A driver for the Winsystems PCM-D/A-12 + * Devices: (Winsystems) PCM-D/A-12 [pcmda12] + * Author: Calin Culianu <calin@xxxxxxxxx> + * Updated: Fri, 13 Jan 2006 12:01:01 -0500 + * Status: works + * + * A driver for the relatively straightforward-to-program PCM-D/A-12. + * This board doesn't support commands, and the only way to set its + * analog output range is to jumper the board. As such, + * comedi_data_write() ignores the range value specified. + * + * The board uses 16 consecutive I/O addresses starting at the I/O port + * base address. Each address corresponds to the LSB then MSB of a + * particular channel from 0-7. + * + * Note that the board is not ISA-PNP capable and thus needs the I/O + * port comedi_config parameter. + * + * Note that passing a nonzero value as the second config option will + * enable "simultaneous xfer" mode for this board, in which AO writes + * will not take effect until a subsequent read of any AO channel. This + * is so that one can speed up programming by preloading all AO registers + * with values before simultaneously setting them to take effect with one + * read command. + * + * Configuration Options: + * [0] - I/O port base address + * [1] - Do Simultaneous Xfer (see description) + */ #include "../comedidev.h" -- 1.8.1.4 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
