The PLX INTCSR register defines are a bit wordy and many of them
are not used anywhere.
For aesthetic reasons, remove all the *_MASK and *_DISABLED defines
and rename the remaining bit defines so they are not as wordy.
Convert all the bit defines to bit shifts.
Signed-off-by: H Hartley Sweeten <hsweeten@xxxxxxxxxxxxxxxxxxx>
Cc: Ian Abbott <abbotti@xxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/staging/comedi/drivers/amplc_pc236.c | 36 +++++++--------
drivers/staging/comedi/drivers/cb_pcimdas.c | 1 +
drivers/staging/comedi/drivers/plx9052.h | 69 ++++++----------------------
3 files changed, 32 insertions(+), 74 deletions(-)
diff --git a/drivers/staging/comedi/drivers/amplc_pc236.c b/drivers/staging/comedi/drivers/amplc_pc236.c
index 441e273..e789383 100644
--- a/drivers/staging/comedi/drivers/amplc_pc236.c
+++ b/drivers/staging/comedi/drivers/amplc_pc236.c
@@ -75,23 +75,19 @@ unused.
#define PC236_IO_SIZE 4
#define PC236_LCR_IO_SIZE 128
-/*
- * INTCSR values for PCI236.
- */
-/* Disable interrupt, also clear any interrupt there */
-#define PCI236_INTR_DISABLE (PLX9052_INTCSR_LI1ENAB_DISABLED \
- | PLX9052_INTCSR_LI1POL_HIGH \
- | PLX9052_INTCSR_LI2POL_HIGH \
- | PLX9052_INTCSR_PCIENAB_DISABLED \
- | PLX9052_INTCSR_LI1SEL_EDGE \
- | PLX9052_INTCSR_LI1CLRINT_ASSERTED)
-/* Enable interrupt, also clear any interrupt there. */
-#define PCI236_INTR_ENABLE (PLX9052_INTCSR_LI1ENAB_ENABLED \
- | PLX9052_INTCSR_LI1POL_HIGH \
- | PLX9052_INTCSR_LI2POL_HIGH \
- | PLX9052_INTCSR_PCIENAB_ENABLED \
- | PLX9052_INTCSR_LI1SEL_EDGE \
- | PLX9052_INTCSR_LI1CLRINT_ASSERTED)
+/* Disable, and clear, interrupts */
+#define PCI236_INTR_DISABLE (PLX9052_INTCSR_LI1POL | \
+ PLX9052_INTCSR_LI2POL | \
+ PLX9052_INTCSR_LI1SEL | \
+ PLX9052_INTCSR_LI1CLRINT)
+
+/* Enable, and clear, interrupts */
+#define PCI236_INTR_ENABLE (PLX9052_INTCSR_LI1ENAB | \
+ PLX9052_INTCSR_LI1POL | \
+ PLX9052_INTCSR_LI2POL | \
+ PLX9052_INTCSR_PCIENAB | \
+ PLX9052_INTCSR_LI1SEL | \
+ PLX9052_INTCSR_LI1CLRINT)
/*
* Board descriptions for Amplicon PC36AT and PCI236.
@@ -257,14 +253,14 @@ static int pc236_intr_check(struct comedi_device *dev)
struct pc236_private *devpriv = dev->private;
int retval = 0;
unsigned long flags;
+ unsigned int intcsr;
spin_lock_irqsave(&dev->spinlock, flags);
if (devpriv->enable_irq) {
retval = 1;
if (is_pci_board(thisboard)) {
- if ((inl(devpriv->lcr_iobase + PLX9052_INTCSR)
- & PLX9052_INTCSR_LI1STAT_MASK)
- == PLX9052_INTCSR_LI1STAT_INACTIVE) {
+ intcsr = inl(devpriv->lcr_iobase + PLX9052_INTCSR);
+ if (!(intcsr & PLX9052_INTCSR_LI1STAT)) {
retval = 0;
} else {
/* Clear interrupt and keep it enabled. */
diff --git a/drivers/staging/comedi/drivers/cb_pcimdas.c b/drivers/staging/comedi/drivers/cb_pcimdas.c
index 31273f4..29813c9 100644
--- a/drivers/staging/comedi/drivers/cb_pcimdas.c
+++ b/drivers/staging/comedi/drivers/cb_pcimdas.c
@@ -46,6 +46,7 @@ See http://www.mccdaq.com/PDFs/Manuals/pcim-das1602-16.pdf for more details.
#include "../comedidev.h"
+#include "plx9052.h"
#include "8255.h"
/* #define CBPCIMDAS_DEBUG */
diff --git a/drivers/staging/comedi/drivers/plx9052.h b/drivers/staging/comedi/drivers/plx9052.h
index 5894739..ab93b0b 100644
--- a/drivers/staging/comedi/drivers/plx9052.h
+++ b/drivers/staging/comedi/drivers/plx9052.h
@@ -27,60 +27,21 @@
#define _PLX9052_H_
/*
- * PLX PCI9052 INTCSR register.
+ * INTCSR - Interrupt Control/Status register
*/
-#define PLX9052_INTCSR 0x4C /* Offset in Local Configuration Registers */
-/* Local Interrupt 1 Enable */
-#define PLX9052_INTCSR_LI1ENAB_MASK 0x0001
-#define PLX9052_INTCSR_LI1ENAB_DISABLED 0x0000
-#define PLX9052_INTCSR_LI1ENAB_ENABLED 0x0001
-/* Local Interrupt 1 Polarity */
-#define PLX9052_INTCSR_LI1POL_MASK 0x0002
-#define PLX9052_INTCSR_LI1POL_LOW 0x0000
-#define PLX9052_INTCSR_LI1POL_HIGH 0x0002
-/* Local Interrupt 1 Status (read-only) */
-#define PLX9052_INTCSR_LI1STAT_MASK 0x0004
-#define PLX9052_INTCSR_LI1STAT_INACTIVE 0x0000
-#define PLX9052_INTCSR_LI1STAT_ACTIVE 0x0004
-/* Local Interrupt 2 Enable */
-#define PLX9052_INTCSR_LI2ENAB_MASK 0x0008
-#define PLX9052_INTCSR_LI2ENAB_DISABLED 0x0000
-#define PLX9052_INTCSR_LI2ENAB_ENABLED 0x0008
-/* Local Interrupt 2 Polarity */
-#define PLX9052_INTCSR_LI2POL_MASK 0x0010
-#define PLX9052_INTCSR_LI2POL_LOW 0x0000
-#define PLX9052_INTCSR_LI2POL_HIGH 0x0010
-/* Local Interrupt 2 Status (read-only) */
-#define PLX9052_INTCSR_LI2STAT_MASK 0x0020
-#define PLX9052_INTCSR_LI2STAT_INACTIVE 0x0000
-#define PLX9052_INTCSR_LI2STAT_ACTIVE 0x0020
-/* PCI Interrupt Enable */
-#define PLX9052_INTCSR_PCIENAB_MASK 0x0040
-#define PLX9052_INTCSR_PCIENAB_DISABLED 0x0000
-#define PLX9052_INTCSR_PCIENAB_ENABLED 0x0040
-/* Software Interrupt */
-#define PLX9052_INTCSR_SOFTINT_MASK 0x0080
-#define PLX9052_INTCSR_SOFTINT_UNASSERTED 0x0000
-#define PLX9052_INTCSR_SOFTINT_ASSERTED 0x0080
-/* Local Interrupt 1 Select Enable */
-#define PLX9052_INTCSR_LI1SEL_MASK 0x0100
-#define PLX9052_INTCSR_LI1SEL_LEVEL 0x0000
-#define PLX9052_INTCSR_LI1SEL_EDGE 0x0100
-/* Local Interrupt 2 Select Enable */
-#define PLX9052_INTCSR_LI2SEL_MASK 0x0200
-#define PLX9052_INTCSR_LI2SEL_LEVEL 0x0000
-#define PLX9052_INTCSR_LI2SEL_EDGE 0x0200
-/* Local Edge Triggerable Interrupt 1 Clear Bit */
-#define PLX9052_INTCSR_LI1CLRINT_MASK 0x0400
-#define PLX9052_INTCSR_LI1CLRINT_UNASSERTED 0x0000
-#define PLX9052_INTCSR_LI1CLRINT_ASSERTED 0x0400
-/* Local Edge Triggerable Interrupt 2 Clear Bit */
-#define PLX9052_INTCSR_LI2CLRINT_MASK 0x0800
-#define PLX9052_INTCSR_LI2CLRINT_UNASSERTED 0x0000
-#define PLX9052_INTCSR_LI2CLRINT_ASSERTED 0x0800
-/* ISA Interface Mode Enable (read-only over PCI bus) */
-#define PLX9052_INTCSR_ISAMODE_MASK 0x1000
-#define PLX9052_INTCSR_ISAMODE_DISABLED 0x0000
-#define PLX9052_INTCSR_ISAMODE_ENABLED 0x1000
+#define PLX9052_INTCSR 0x4c
+#define PLX9052_INTCSR_LI1ENAB (1 << 0) /* LI1 enabled */
+#define PLX9052_INTCSR_LI1POL (1 << 1) /* LI1 active high */
+#define PLX9052_INTCSR_LI1STAT (1 << 2) /* LI1 active */
+#define PLX9052_INTCSR_LI2ENAB (1 << 3) /* LI2 enabled */
+#define PLX9052_INTCSR_LI2POL (1 << 4) /* LI2 active high */
+#define PLX9052_INTCSR_LI2STAT (1 << 5) /* LI2 active */
+#define PLX9052_INTCSR_PCIENAB (1 << 6) /* PCIINT enabled */
+#define PLX9052_INTCSR_SOFTINT (1 << 7) /* generate soft int */
+#define PLX9052_INTCSR_LI1SEL (1 << 8) /* LI1 edge */
+#define PLX9052_INTCSR_LI2SEL (1 << 9) /* LI2 edge */
+#define PLX9052_INTCSR_LI1CLRINT (1 << 10) /* LI1 clear int */
+#define PLX9052_INTCSR_LI2CLRINT (1 << 11) /* LI2 clear int */
+#define PLX9052_INTCSR_ISAMODE (1 << 12) /* ISA interface mode */
#endif /* _PLX9052_H_ */
--
1.8.1.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
