Use register name defines instead of magic numbers where a bit of
clarity would be useful.
Also a small typo fix and some register prefixes added, for further
clarity.
Signed-off-by: Mark Einon <mark.einon@xxxxxxxxx>
---
drivers/staging/et131x/et131x.c | 132 ++++++++++++++++++++++-----------------
drivers/staging/et131x/et131x.h | 88 +++++++++++++++++++-------
2 files changed, 139 insertions(+), 81 deletions(-)
diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c
index b08dff9..e2d5555 100644
--- a/drivers/staging/et131x/et131x.c
+++ b/drivers/staging/et131x/et131x.c
@@ -344,6 +344,10 @@ struct rx_ring {
* 14: UDP checksum assist
*/
+#define TXDESC_FLAG_LASTPKT 0x0001
+#define TXDESC_FLAG_FIRSTPKT 0x0002
+#define TXDESC_FLAG_INTPROC 0x0004
+
/* struct tx_desc represents each descriptor on the ring */
struct tx_desc {
u32 addr_hi;
@@ -774,13 +778,12 @@ static int et131x_init_eeprom(struct et131x_adapter *adapter)
/* We first need to check the EEPROM Status code located at offset
* 0xB2 of config space
*/
- pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS,
- &eestatus);
+ pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, &eestatus);
/* THIS IS A WORKAROUND:
* I need to call this function twice to get my card in a
* LG M1 Express Dual running. I tried also a msleep before this
- * function, because I thought there could be some time condidions
+ * function, because I thought there could be some time conditions
* but it didn't work. Call the whole function twice also work.
*/
if (pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, &eestatus)) {
@@ -932,7 +935,10 @@ static void et1310_config_mac_regs1(struct et131x_adapter *adapter)
/* First we need to reset everything. Write to MAC configuration
* register 1 to perform reset.
*/
- writel(0xC00F0000, ¯egs->cfg1);
+ writel(ET_MAC_CFG1_SOFT_RESET | ET_MAC_CFG1_SIM_RESET |
+ ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC |
+ ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC,
+ ¯egs->cfg1);
/* Next lets configure the MAC Inter-packet gap register */
ipg = 0x38005860; /* IPG1 0x38 IPG2 0x58 B2B 0x60 */
@@ -947,7 +953,7 @@ static void et1310_config_mac_regs1(struct et131x_adapter *adapter)
writel(0, ¯egs->if_ctrl);
/* Let's move on to setting up the mii management configuration */
- writel(0x07, ¯egs->mii_mgmt_cfg); /* Clock reset 0x7 */
+ writel(ET_MAC_MIIMGMT_CLK_RST, ¯egs->mii_mgmt_cfg);
/* Next lets configure the MAC Station Address register. These
* values are read from the EEPROM during initialization and stored
@@ -998,38 +1004,43 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter)
ifctrl = readl(&mac->if_ctrl);
/* Set up the if mode bits */
- cfg2 &= ~0x300;
+ cfg2 &= ~ET_MAC_CFG2_IFMODE_MASK;
if (phydev && phydev->speed == SPEED_1000) {
- cfg2 |= 0x200;
+ cfg2 |= ET_MAC_CFG2_IFMODE_1000;
/* Phy mode bit */
- ifctrl &= ~(1 << 24);
+ ifctrl &= ~ET_MAC_IFCTRL_PHYMODE;
} else {
- cfg2 |= 0x100;
- ifctrl |= (1 << 24);
+ cfg2 |= ET_MAC_CFG2_IFMODE_100;
+ ifctrl |= ET_MAC_IFCTRL_PHYMODE;
}
/* We need to enable Rx/Tx */
- cfg1 |= CFG1_RX_ENABLE | CFG1_TX_ENABLE | CFG1_TX_FLOW;
+ cfg1 |= ET_MAC_CFG1_RX_ENABLE | ET_MAC_CFG1_TX_ENABLE |
+ ET_MAC_CFG1_TX_FLOW;
/* Initialize loop back to off */
- cfg1 &= ~(CFG1_LOOPBACK | CFG1_RX_FLOW);
+ cfg1 &= ~(ET_MAC_CFG1_LOOPBACK | ET_MAC_CFG1_RX_FLOW);
if (adapter->flowcontrol == FLOW_RXONLY ||
adapter->flowcontrol == FLOW_BOTH)
- cfg1 |= CFG1_RX_FLOW;
+ cfg1 |= ET_MAC_CFG1_RX_FLOW;
writel(cfg1, &mac->cfg1);
/* Now we need to initialize the MAC Configuration 2 register */
/* preamble 7, check length, huge frame off, pad crc, crc enable
full duplex off */
- cfg2 |= 0x7016;
- cfg2 &= ~0x0021;
+ cfg2 |= 0x7 << ET_MAC_CFG2_PREAMBLE_SHIFT;
+ cfg2 |= ET_MAC_CFG2_IFMODE_LEN_CHECK;
+ cfg2 |= ET_MAC_CFG2_IFMODE_PAD_CRC;
+ cfg2 |= ET_MAC_CFG2_IFMODE_CRC_ENABLE;
+ cfg2 &= ~ET_MAC_CFG2_IFMODE_HUGE_FRAME;
+ cfg2 &= ~ET_MAC_CFG2_IFMODE_FULL_DPLX;
/* Turn on duplex if needed */
if (phydev && phydev->duplex == DUPLEX_FULL)
- cfg2 |= 0x01;
+ cfg2 |= ET_MAC_CFG2_IFMODE_FULL_DPLX;
- ifctrl &= ~(1 << 26);
+ ifctrl &= ~ET_MAC_IFCTRL_GHDMODE;
if (phydev && phydev->duplex == DUPLEX_HALF)
- ifctrl |= (1<<26); /* Enable ghd */
+ ifctrl |= ET_MAC_IFCTRL_GHDMODE;
writel(ifctrl, &mac->if_ctrl);
writel(cfg2, &mac->cfg2);
@@ -1038,7 +1049,7 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter)
udelay(10);
delay++;
cfg1 = readl(&mac->cfg1);
- } while ((cfg1 & CFG1_WAIT) != CFG1_WAIT && delay < 100);
+ } while ((cfg1 & ET_MAC_CFG1_WAIT) != ET_MAC_CFG1_WAIT && delay < 100);
if (delay == 100) {
dev_warn(&adapter->pdev->dev,
@@ -1047,7 +1058,7 @@ static void et1310_config_mac_regs2(struct et131x_adapter *adapter)
}
/* Enable txmac */
- ctl |= 0x09; /* TX mac enable, FC disable */
+ ctl |= ET_TX_CTRL_TXMAC_ENABLE | ET_TX_CTRL_FC_DISABLE;
writel(ctl, &adapter->regs->txmac.ctl);
/* Ready to start the RXDMA/TXDMA engine */
@@ -1139,19 +1150,19 @@ static void et1310_setup_device_for_unicast(struct et131x_adapter *adapter)
* Set up unicast packet filter reg 3 to be the octets 2 - 5 of the
* MAC address for first address
*/
- uni_pf3 = (adapter->addr[0] << ET_UNI_PF_ADDR2_1_SHIFT) |
- (adapter->addr[1] << ET_UNI_PF_ADDR2_2_SHIFT) |
- (adapter->addr[0] << ET_UNI_PF_ADDR1_1_SHIFT) |
+ uni_pf3 = (adapter->addr[0] << ET_RX_UNI_PF_ADDR2_1_SHIFT) |
+ (adapter->addr[1] << ET_RX_UNI_PF_ADDR2_2_SHIFT) |
+ (adapter->addr[0] << ET_RX_UNI_PF_ADDR1_1_SHIFT) |
adapter->addr[1];
- uni_pf2 = (adapter->addr[2] << ET_UNI_PF_ADDR2_3_SHIFT) |
- (adapter->addr[3] << ET_UNI_PF_ADDR2_4_SHIFT) |
- (adapter->addr[4] << ET_UNI_PF_ADDR2_5_SHIFT) |
+ uni_pf2 = (adapter->addr[2] << ET_RX_UNI_PF_ADDR2_3_SHIFT) |
+ (adapter->addr[3] << ET_RX_UNI_PF_ADDR2_4_SHIFT) |
+ (adapter->addr[4] << ET_RX_UNI_PF_ADDR2_5_SHIFT) |
adapter->addr[5];
- uni_pf1 = (adapter->addr[2] << ET_UNI_PF_ADDR1_3_SHIFT) |
- (adapter->addr[3] << ET_UNI_PF_ADDR1_4_SHIFT) |
- (adapter->addr[4] << ET_UNI_PF_ADDR1_5_SHIFT) |
+ uni_pf1 = (adapter->addr[2] << ET_RX_UNI_PF_ADDR1_3_SHIFT) |
+ (adapter->addr[3] << ET_RX_UNI_PF_ADDR1_4_SHIFT) |
+ (adapter->addr[4] << ET_RX_UNI_PF_ADDR1_5_SHIFT) |
adapter->addr[5];
pm_csr = readl(&adapter->regs->global.pm_csr);
@@ -1208,13 +1219,13 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter)
writel(0, &rxmac->mask4_word3);
/* Lets setup the WOL Source Address */
- sa_lo = (adapter->addr[2] << ET_WOL_LO_SA3_SHIFT) |
- (adapter->addr[3] << ET_WOL_LO_SA4_SHIFT) |
- (adapter->addr[4] << ET_WOL_LO_SA5_SHIFT) |
+ sa_lo = (adapter->addr[2] << ET_RX_WOL_LO_SA3_SHIFT) |
+ (adapter->addr[3] << ET_RX_WOL_LO_SA4_SHIFT) |
+ (adapter->addr[4] << ET_RX_WOL_LO_SA5_SHIFT) |
adapter->addr[5];
writel(sa_lo, &rxmac->sa_lo);
- sa_hi = (u32) (adapter->addr[0] << ET_WOL_HI_SA1_SHIFT) |
+ sa_hi = (u32) (adapter->addr[0] << ET_RX_WOL_HI_SA1_SHIFT) |
adapter->addr[1];
writel(sa_hi, &rxmac->sa_hi);
@@ -1224,7 +1235,7 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter)
/* Let's initialize the Unicast Packet filtering address */
if (adapter->packet_filter & ET131X_PACKET_TYPE_DIRECTED) {
et1310_setup_device_for_unicast(adapter);
- pf_ctrl |= 4; /* Unicast filter */
+ pf_ctrl |= ET_RX_PFCTRL_UNICST_FILTER_ENABLE;
} else {
writel(0, &rxmac->uni_pf_addr1);
writel(0, &rxmac->uni_pf_addr2);
@@ -1233,13 +1244,13 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter)
/* Let's initialize the Multicast hash */
if (!(adapter->packet_filter & ET131X_PACKET_TYPE_ALL_MULTICAST)) {
- pf_ctrl |= 2; /* Multicast filter */
+ pf_ctrl |= ET_RX_PFCTRL_MLTCST_FILTER_ENABLE;
et1310_setup_device_for_multicast(adapter);
}
/* Runt packet filtering. Didn't work in version A silicon. */
- pf_ctrl |= (NIC_MIN_PACKET_SIZE + 4) << 16;
- pf_ctrl |= 8; /* Fragment filter */
+ pf_ctrl |= (NIC_MIN_PACKET_SIZE + 4) << ET_RX_PFCTRL_MIN_PKT_SZ_SHIFT;
+ pf_ctrl |= ET_RX_PFCTRL_FRAG_FILTER_ENABLE;
if (adapter->registry_jumbo_packet > 8192)
/* In order to transmit jumbo packets greater than 8k, the
@@ -1290,7 +1301,7 @@ static void et1310_config_rxmac_regs(struct et131x_adapter *adapter)
* but we still leave the packet filter on.
*/
writel(pf_ctrl, &rxmac->pf_ctrl);
- writel(0x9, &rxmac->ctrl);
+ writel(ET_RX_CTRL_RXMAC_ENABLE | ET_RX_CTRL_WOL_DISABLE, &rxmac->ctrl);
}
static void et1310_config_txmac_regs(struct et131x_adapter *adapter)
@@ -1401,7 +1412,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr,
writel(0, &mac->mii_mgmt_cmd);
/* Set up the register we need to read from on the correct PHY */
- writel(MII_ADDR(addr, reg), &mac->mii_mgmt_addr);
+ writel(ET_MAC_MII_ADDR(addr, reg), &mac->mii_mgmt_addr);
writel(0x1, &mac->mii_mgmt_cmd);
@@ -1409,7 +1420,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr,
udelay(50);
delay++;
mii_indicator = readl(&mac->mii_mgmt_indicator);
- } while ((mii_indicator & MGMT_WAIT) && delay < 50);
+ } while ((mii_indicator & ET_MAC_MGMT_WAIT) && delay < 50);
/* If we hit the max delay, we could not read the register */
if (delay == 50) {
@@ -1423,7 +1434,7 @@ static int et131x_phy_mii_read(struct et131x_adapter *adapter, u8 addr,
/* If we hit here we were able to read the register and we need to
* return the value to the caller */
- *value = readl(&mac->mii_mgmt_stat) & 0xFFFF;
+ *value = readl(&mac->mii_mgmt_stat) & ET_MAC_MIIMGMT_STAT_PHYCRTL_MASK;
/* Stop the read operation */
writel(0, &mac->mii_mgmt_cmd);
@@ -1483,7 +1494,7 @@ static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value)
writel(0, &mac->mii_mgmt_cmd);
/* Set up the register we need to write to on the correct PHY */
- writel(MII_ADDR(addr, reg), &mac->mii_mgmt_addr);
+ writel(ET_MAC_MII_ADDR(addr, reg), &mac->mii_mgmt_addr);
/* Add the value to write to the registers to the mac */
writel(value, &mac->mii_mgmt_ctrl);
@@ -1492,7 +1503,7 @@ static int et131x_mii_write(struct et131x_adapter *adapter, u8 reg, u16 value)
udelay(50);
delay++;
mii_indicator = readl(&mac->mii_mgmt_indicator);
- } while ((mii_indicator & MGMT_BUSY) && delay < 100);
+ } while ((mii_indicator & ET_MAC_MGMT_BUSY) && delay < 100);
/* If we hit the max delay, we could not write the register */
if (delay == 100) {
@@ -1528,7 +1539,7 @@ static void et1310_phy_access_mii_bit(struct et131x_adapter *adapter,
u8 *value)
{
u16 reg;
- u16 mask = 0x0001 << bitnum;
+ u16 mask = 1 << bitnum;
/* Read the requested register */
et131x_mii_read(adapter, regnum, ®);
@@ -1839,7 +1850,7 @@ static void et131x_config_rx_dma_regs(struct et131x_adapter *adapter)
writel(rx_local->psr_num_entries - 1, &rx_dma->psr_num_des);
writel(0, &rx_dma->psr_full_offset);
- psr_num_des = readl(&rx_dma->psr_num_des) & 0xFFF;
+ psr_num_des = readl(&rx_dma->psr_num_des) & ET_RXDMA_PSR_NUM_DES_MASK;
writel((psr_num_des * LO_MARK_PERCENT_FOR_PSR) / 100,
&rx_dma->psr_min_des);
@@ -1983,13 +1994,21 @@ static void et131x_adapter_setup(struct et131x_adapter *adapter)
*/
static void et131x_soft_reset(struct et131x_adapter *adapter)
{
- /* Disable MAC Core */
- writel(0xc00f0000, &adapter->regs->mac.cfg1);
+ u32 reg;
- /* Set everything to a reset value */
- writel(0x7F, &adapter->regs->global.sw_reset);
- writel(0x000f0000, &adapter->regs->mac.cfg1);
- writel(0x00000000, &adapter->regs->mac.cfg1);
+ /* Disable MAC Core */
+ reg = ET_MAC_CFG1_SOFT_RESET | ET_MAC_CFG1_SIM_RESET |
+ ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC |
+ ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC;
+ writel(reg, &adapter->regs->mac.cfg1);
+
+ reg = ET_RESET_ALL;
+ writel(reg, &adapter->regs->global.sw_reset);
+
+ reg = ET_MAC_CFG1_RESET_RXMC | ET_MAC_CFG1_RESET_TXMC |
+ ET_MAC_CFG1_RESET_RXFUNC | ET_MAC_CFG1_RESET_TXFUNC;
+ writel(reg, &adapter->regs->mac.cfg1);
+ writel(0, &adapter->regs->mac.cfg1);
}
/**
@@ -3022,23 +3041,22 @@ static int nic_send_packet(struct et131x_adapter *adapter, struct tcb *tcb)
if (phydev && phydev->speed == SPEED_1000) {
if (++adapter->tx_ring.since_irq == PARM_TX_NUM_BUFS_DEF) {
/* Last element & Interrupt flag */
- desc[frag - 1].flags = 0x5;
+ desc[frag - 1].flags = TXDESC_FLAG_INTPROC | TXDESC_FLAG_LASTPKT;
adapter->tx_ring.since_irq = 0;
} else { /* Last element */
- desc[frag - 1].flags = 0x1;
+ desc[frag - 1].flags = TXDESC_FLAG_LASTPKT;
}
} else
- desc[frag - 1].flags = 0x5;
+ desc[frag - 1].flags = TXDESC_FLAG_INTPROC | TXDESC_FLAG_LASTPKT;
- desc[0].flags |= 2; /* First element flag */
+ desc[0].flags |= TXDESC_FLAG_FIRSTPKT;
tcb->index_start = adapter->tx_ring.send_idx;
tcb->stale = 0;
spin_lock_irqsave(&adapter->send_hw_lock, flags);
- thiscopy = NUM_DESC_PER_RING_TX -
- INDEX10(adapter->tx_ring.send_idx);
+ thiscopy = NUM_DESC_PER_RING_TX - INDEX10(adapter->tx_ring.send_idx);
if (thiscopy >= frag) {
remainder = 0;
diff --git a/drivers/staging/et131x/et131x.h b/drivers/staging/et131x/et131x.h
index 9fa47f9..bbe78a7 100644
--- a/drivers/staging/et131x/et131x.h
+++ b/drivers/staging/et131x/et131x.h
@@ -145,6 +145,8 @@
*31: selfclr_disable
*/
+#define ET_RESET_ALL 0x007F;
+
/*
* SLV Timer reg at address 0x002C (low 24 bits)
*/
@@ -392,6 +394,8 @@ struct txdma_regs { /* Location: */
* 11-0: psr ndes
*/
+#define ET_RXDMA_PSR_NUM_DES_MASK 0xFFF;
+
/*
* structure for packet status ring available offset reg in rxdma address map
* located at address 0x202C
@@ -567,6 +571,9 @@ struct rxdma_regs { /* Location: */
* 0: txmac_en
*/
+#define ET_TX_CTRL_FC_DISABLE 0x0008
+#define ET_TX_CTRL_TXMAC_ENABLE 0x0001
+
/*
* structure for shadow pointer reg in txmac address map
* located at address 0x3004
@@ -682,6 +689,9 @@ struct txmac_regs { /* Location: */
* 0: rxmac_en
*/
+#define ET_RX_CTRL_WOL_DISABLE 0x0008
+#define ET_RX_CTRL_RXMAC_ENABLE 0x0001
+
/*
* structure for Wake On Lan Control and CRC 0 reg in rxmac address map
* located at address 0x4004
@@ -723,9 +733,9 @@ struct txmac_regs { /* Location: */
* 7-0: sa6
*/
-#define ET_WOL_LO_SA3_SHIFT 24
-#define ET_WOL_LO_SA4_SHIFT 16
-#define ET_WOL_LO_SA5_SHIFT 8
+#define ET_RX_WOL_LO_SA3_SHIFT 24
+#define ET_RX_WOL_LO_SA4_SHIFT 16
+#define ET_RX_WOL_LO_SA5_SHIFT 8
/*
* structure for Wake On Lan Source Address Hi reg in rxmac address map
@@ -736,7 +746,7 @@ struct txmac_regs { /* Location: */
* 7-0: sa2
*/
-#define ET_WOL_HI_SA1_SHIFT 8
+#define ET_RX_WOL_HI_SA1_SHIFT 8
/*
* structure for Wake On Lan mask reg in rxmac address map
@@ -754,9 +764,9 @@ struct txmac_regs { /* Location: */
* 7-0: addr1_6
*/
-#define ET_UNI_PF_ADDR1_3_SHIFT 24
-#define ET_UNI_PF_ADDR1_4_SHIFT 16
-#define ET_UNI_PF_ADDR1_5_SHIFT 8
+#define ET_RX_UNI_PF_ADDR1_3_SHIFT 24
+#define ET_RX_UNI_PF_ADDR1_4_SHIFT 16
+#define ET_RX_UNI_PF_ADDR1_5_SHIFT 8
/*
* structure for Unicast Paket Filter Address 2 reg in rxmac address map
@@ -768,9 +778,9 @@ struct txmac_regs { /* Location: */
* 7-0: addr2_6
*/
-#define ET_UNI_PF_ADDR2_3_SHIFT 24
-#define ET_UNI_PF_ADDR2_4_SHIFT 16
-#define ET_UNI_PF_ADDR2_5_SHIFT 8
+#define ET_RX_UNI_PF_ADDR2_3_SHIFT 24
+#define ET_RX_UNI_PF_ADDR2_4_SHIFT 16
+#define ET_RX_UNI_PF_ADDR2_5_SHIFT 8
/*
* structure for Unicast Paket Filter Address 1 & 2 reg in rxmac address map
@@ -782,10 +792,9 @@ struct txmac_regs { /* Location: */
* 7-0: addr1_2
*/
-#define ET_UNI_PF_ADDR2_1_SHIFT 24
-#define ET_UNI_PF_ADDR2_2_SHIFT 16
-#define ET_UNI_PF_ADDR1_1_SHIFT 8
-
+#define ET_RX_UNI_PF_ADDR2_1_SHIFT 24
+#define ET_RX_UNI_PF_ADDR2_2_SHIFT 16
+#define ET_RX_UNI_PF_ADDR1_1_SHIFT 8
/*
* structure for Multicast Hash reg in rxmac address map
@@ -806,6 +815,12 @@ struct txmac_regs { /* Location: */
* 0: filter_broad_en
*/
+#define ET_RX_PFCTRL_MIN_PKT_SZ_SHIFT 16;
+#define ET_RX_PFCTRL_FRAG_FILTER_ENABLE 0x0008;
+#define ET_RX_PFCTRL_UNICST_FILTER_ENABLE 0x0004;
+#define ET_RX_PFCTRL_MLTCST_FILTER_ENABLE 0x0002;
+#define ET_RX_PFCTRL_BRDCST_FILTER_ENABLE 0x0001;
+
/*
* structure for Memory Controller Interface Control Max Segment reg in rxmac
* address map. Located at address 0x4088
@@ -816,6 +831,10 @@ struct txmac_regs { /* Location: */
* 0: seg_en
*/
+#define ET_RX_MCIF_CTRL_MAX_SEG_SIZE_SHIFT 2;
+#define ET_RX_MCIF_CTRL_MAX_SEG_FC_ENABLE 0x0002;
+#define ET_RX_MCIF_CTRL_MAX_SEG_ENABLE 0x0001;
+
/*
* structure for Memory Controller Interface Water Mark reg in rxmac address
* map. Located at address 0x408C
@@ -915,7 +934,6 @@ struct rxmac_regs { /* Location: */
/* END OF RXMAC REGISTER ADDRESS MAP */
-
/* START OF MAC REGISTER ADDRESS MAP */
/*
@@ -940,12 +958,18 @@ struct rxmac_regs { /* Location: */
* 0: tx enable
*/
-#define CFG1_LOOPBACK 0x00000100
-#define CFG1_RX_FLOW 0x00000020
-#define CFG1_TX_FLOW 0x00000010
-#define CFG1_RX_ENABLE 0x00000004
-#define CFG1_TX_ENABLE 0x00000001
-#define CFG1_WAIT 0x0000000A /* RX & TX syncd */
+#define ET_MAC_CFG1_SOFT_RESET 0x80000000
+#define ET_MAC_CFG1_SIM_RESET 0x40000000
+#define ET_MAC_CFG1_RESET_RXMC 0x00080000
+#define ET_MAC_CFG1_RESET_TXMC 0x00040000
+#define ET_MAC_CFG1_RESET_RXFUNC 0x00020000
+#define ET_MAC_CFG1_RESET_TXFUNC 0x00010000
+#define ET_MAC_CFG1_LOOPBACK 0x00000100
+#define ET_MAC_CFG1_RX_FLOW 0x00000020
+#define ET_MAC_CFG1_TX_FLOW 0x00000010
+#define ET_MAC_CFG1_RX_ENABLE 0x00000004
+#define ET_MAC_CFG1_TX_ENABLE 0x00000001
+#define ET_MAC_CFG1_WAIT 0x0000000A /* RX & TX syncd */
/*
* structure for configuration #2 reg in mac address map.
@@ -963,6 +987,15 @@ struct rxmac_regs { /* Location: */
* 0: full duplex
*/
+#define ET_MAC_CFG2_PREAMBLE_SHIFT 12;
+#define ET_MAC_CFG2_IFMODE_MASK 0x0300;
+#define ET_MAC_CFG2_IFMODE_1000 0x0200;
+#define ET_MAC_CFG2_IFMODE_100 0x0100;
+#define ET_MAC_CFG2_IFMODE_HUGE_FRAME 0x0020;
+#define ET_MAC_CFG2_IFMODE_LEN_CHECK 0x0010;
+#define ET_MAC_CFG2_IFMODE_PAD_CRC 0x0004;
+#define ET_MAC_CFG2_IFMODE_CRC_ENABLE 0x0002;
+#define ET_MAC_CFG2_IFMODE_FULL_DPLX 0x0001;
/*
* structure for Interpacket gap reg in mac address map.
@@ -1017,6 +1050,8 @@ struct rxmac_regs { /* Location: */
* 2-0: mgmt clock reset
*/
+#define ET_MAC_MIIMGMT_CLK_RST 0x0007
+
/*
* structure for MII Management Command reg in mac address map.
* located at address 0x5024
@@ -1033,7 +1068,7 @@ struct rxmac_regs { /* Location: */
* 4-0: register
*/
-#define MII_ADDR(phy, reg) ((phy) << 8 | (reg))
+#define ET_MAC_MII_ADDR(phy, reg) ((phy) << 8 | (reg))
/*
* structure for MII Management Control reg in mac address map.
@@ -1049,6 +1084,8 @@ struct rxmac_regs { /* Location: */
* 15-0: phy control
*/
+#define ET_MAC_MIIMGMT_STAT_PHYCRTL_MASK 0xFFFF;
+
/*
* structure for MII Management Indicators reg in mac address map.
* located at address 0x5034
@@ -1058,8 +1095,8 @@ struct rxmac_regs { /* Location: */
* 0: busy
*/
-#define MGMT_BUSY 0x00000001 /* busy */
-#define MGMT_WAIT 0x00000005 /* busy | not valid */
+#define ET_MAC_MGMT_BUSY 0x00000001 /* busy */
+#define ET_MAC_MGMT_WAIT 0x00000005 /* busy | not valid */
/*
* structure for Interface Control reg in mac address map.
@@ -1084,6 +1121,9 @@ struct rxmac_regs { /* Location: */
* 0: enable jabber protection
*/
+#define ET_MAC_IFCTRL_GHDMODE (1 << 26)
+#define ET_MAC_IFCTRL_PHYMODE (1 << 24)
+
/*
* structure for Interface Status reg in mac address map.
* located at address 0x503C
--
1.7.9.5
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
