Fixed coding style issues.
---
drivers/staging/rtl8187se/r8185b_init.c | 57 ++++++++++++++++---------------
1 file changed, 30 insertions(+), 27 deletions(-)
diff --git a/drivers/staging/rtl8187se/r8185b_init.c b/drivers/staging/rtl8187se/r8185b_init.c
index bf34319..da4f592 100644
--- a/drivers/staging/rtl8187se/r8185b_init.c
+++ b/drivers/staging/rtl8187se/r8185b_init.c
@@ -579,13 +579,13 @@ void ZEBRA_Config_85BASIC_HardCode(struct net_device *dev)
RF_WriteReg(dev, 0x0a, 0x0001); mdelay(1);
/* For crystal calibration, added by Roger, 2007.12.11. */
if (priv->bXtalCalibration) { /* reg 30. */
- /*
- * enable crystal calibration.
- * RF Reg[30], (1)Xin:[12:9], Xout:[8:5], addr[4:0].
- * (2)PA Pwr delay timer[15:14], default: 2.4us, set BIT15=0
- * (3)RF signal on/off when calibration[13], default: on, set BIT13=0.
- * So we should minus 4 BITs offset.
- */
+ /*
+ * enable crystal calibration.
+ * RF Reg[30], (1)Xin:[12:9], Xout:[8:5], addr[4:0].
+ * (2)PA Pwr delay timer[15:14], default: 2.4us, set BIT15=0
+ * (3)RF signal on/off when calibration[13], default: on, set BIT13=0.
+ * So we should minus 4 BITs offset.
+ */
RF_WriteReg(dev, 0x0f, (priv->XtalCal_Xin<<5) | (priv->XtalCal_Xout<<1) | BIT11 | BIT9); mdelay(1);
printk("ZEBRA_Config_85BASIC_HardCode(): (%02x)\n",
(priv->XtalCal_Xin<<5) | (priv->XtalCal_Xout<<1) | BIT11 | BIT9);
@@ -1120,24 +1120,24 @@ void ActSetWirelessMode8185(struct net_device *dev, u8 btWirelessMode)
}
}
- /*
- * 2. Swtich band: RF or BB specific actions,
+ /*
+ * 2. Swtich band: RF or BB specific actions,
* for example, refresh tables in omc8255, or change initial gain if necessary.
* Nothing to do for Zebra to switch band.
- * Update current wireless mode if we switch to specified band successfully.
+ * Update current wireless mode if we switch to specified band successfully.
*/
ieee->mode = (WIRELESS_MODE)btWirelessMode;
/* 3. Change related setting. */
- if( ieee->mode == WIRELESS_MODE_A ) {
+ if (ieee->mode == WIRELESS_MODE_A) {
DMESG("WIRELESS_MODE_A\n");
- } else if( ieee->mode == WIRELESS_MODE_B ) {
+ } else if (ieee->mode == WIRELESS_MODE_B) {
DMESG("WIRELESS_MODE_B\n");
- } else if( ieee->mode == WIRELESS_MODE_G ) {
+ } else if (ieee->mode == WIRELESS_MODE_G) {
DMESG("WIRELESS_MODE_G\n");
}
- ActUpdateChannelAccessSetting( dev, ieee->mode, &priv->ChannelAccessSetting);
+ ActUpdateChannelAccessSetting(dev, ieee->mode, &priv->ChannelAccessSetting);
}
void rtl8185b_irq_enable(struct net_device *dev)
@@ -1167,13 +1167,14 @@ void MgntDisconnectIBSS(struct net_device *dev)
priv->ieee80211->state = IEEE80211_NOLINK;
/*
- * Stop Beacon.
+ * Stop Beacon.
*
- * Vista add a Adhoc profile, HW radio off until OID_DOT11_RESET_REQUEST
- * Driver would set MSR=NO_LINK, then HW Radio ON, MgntQueue Stuck.
- * Because Bcn DMA isn't complete, mgnt queue would stuck until Bcn packet send.
+ * Vista add a Adhoc profile, HW radio off until OID_DOT11_RESET_REQUEST
+ * Driver would set MSR=NO_LINK, then HW Radio ON, MgntQueue Stuck.
+ * Because Bcn DMA isn't complete, mgnt queue would stuck until Bcn
+ * packet send.
*
- * Disable Beacon Queue Own bit, suggested by jong
+ * Disable Beacon Queue Own bit, suggested by jong
*/
ieee80211_stop_send_beacons(priv->ieee80211);
@@ -1208,10 +1209,12 @@ void MgntDisconnectAP(struct net_device *dev, u8 asRsn)
* Commented out by rcnjko, 2005.01.27:
* I move SecClearAllKeys() to MgntActSet_802_11_DISASSOCIATE().
*
- * 2004/09/15, kcwu, the key should be cleared, or the new handshaking will not success
+ * 2004/09/15, kcwu, the key should be cleared, or
+ * the new handshaking will not success
*
- * In WPA WPA2 need to Clear all key ... because new key will set after new handshaking.
- * 2004.10.11, by rcnjko.
+ * In WPA WPA2 need to Clear all key ... because new key
+ * will set after new handshaking.
+ * 2004.10.11, by rcnjko.
*/
MlmeDisassociateRequest(dev, priv->ieee80211->current_network.bssid, asRsn);
@@ -1234,11 +1237,11 @@ bool MgntDisconnect(struct net_device *dev, u8 asRsn)
if (priv->ieee80211->iw_mode == IW_MODE_INFRA) {
/*
- * We clear key here instead of MgntDisconnectAP() because that
- * MgntActSet_802_11_DISASSOCIATE() is an interface called by OS,
- * e.g. OID_802_11_DISASSOCIATE in Windows while as MgntDisconnectAP() is
- * used to handle disassociation related things to AP, e.g. send Disassoc
- * frame to AP. 2005.01.27, by rcnjko.
+ * We clear key here instead of MgntDisconnectAP() because that
+ * MgntActSet_802_11_DISASSOCIATE() is an interface called by OS,
+ * e.g. OID_802_11_DISASSOCIATE in Windows while as MgntDisconnectAP() is
+ * used to handle disassociation related things to AP, e.g. send Disassoc
+ * frame to AP. 2005.01.27, by rcnjko.
*/
MgntDisconnectAP(dev, asRsn);
}
--
1.7.10.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
