On Sat, 14 Apr 2012, Andres Salomon wrote:
> On Sun, 15 Apr 2012 00:53:04 +0200 (CEST)
> Jesper Juhl <jj@xxxxxxxxxxxxx> wrote:
>
> > This patch removes the few checkpatch.pl issues that are currently
> > reported for this file.
> >
> > It makes these changes:
> >
> > 1. Quoted strings that were broken over multiple lines are put on a
> > single line for easier grep'ability.
> >
> > 2. Add missing level to a printk().
> >
> > 3. A few casts have had their space between the cast and variable
> > removed.
> >
>
> These first three look fine.
>
>
> > 4. Two msleep() calls with times <= 20 have been changed to
> > usleep_range() calls instead since msleep(<=20) may sleep for 20ms
> > (on 100Hz kernels for instance).
> > Picking a value for the lower bound of the range was easy, that was
> > just the value passed to msleep(). As for picking the upper bound
> > of the sleep I just went with two times the lower bound, for no
> > other reason than the fact that in both cases that value was <=20ms
> > and the end result will in any case be closer to the intention than
> > a 20ms sleep.
>
>
> That msleep(1) was replaced with a longer msleep and fewer dcon_read
> attempts in OLPC's XO-1.75 kernel. The msleep(10) should probably be
> a shorter usleep (though we'd need to test it). In general, this
> stuff was done to work around bugs in the dcon, and the timing of these
> bugs appears to differ (probably due to smbus timing) between the
> various OLPC platforms - XO-1 (x86 amd geode), XO-1.5 (x86 via), and
> XO-1.75 (arm armada 610).
>
> Given that, I'd prefer to leave these alone and figure out the proper
> values later (with lots of testing). Mind resubmitting with the
> msleep changes removed?
>
Not at all :-)
How's this?
From: Jesper Juhl <jj@xxxxxxxxxxxxx>
Date: Sun, 15 Apr 2012 00:38:03 +0200
Subject: [PATCH] staging: olpc_dcon.c: checkpatch.pl and style fixups
This patch removes a few checkpatch.pl issues that are currently
reported for this file.
It makes these changes:
1. Quoted strings that were broken over multiple lines are put on a
single line for easier grep'ability.
2. Add missing level to a printk().
3. A few casts have had their space between the cast and variable
removed.
I have not tested this patch beyond checking that it compiles.
Signed-off-by: Jesper Juhl <jj@xxxxxxxxxxxxx>
---
drivers/staging/olpc_dcon/olpc_dcon.c | 29 ++++++++++++++---------------
1 file changed, 14 insertions(+), 15 deletions(-)
diff --git a/drivers/staging/olpc_dcon/olpc_dcon.c b/drivers/staging/olpc_dcon/olpc_dcon.c
index 3d91993..43758c3 100644
--- a/drivers/staging/olpc_dcon/olpc_dcon.c
+++ b/drivers/staging/olpc_dcon/olpc_dcon.c
@@ -71,8 +71,8 @@ static int dcon_hw_init(struct dcon_priv *dcon, int is_init)
ver = dcon_read(dcon, DCON_REG_ID);
if ((ver >> 8) != 0xDC) {
- printk(KERN_ERR "olpc-dcon: DCON ID not 0xDCxx: 0x%04x "
- "instead.\n", ver);
+ printk(KERN_ERR "olpc-dcon: DCON ID not 0xDCxx: 0x%04x instead.\n",
+ ver);
rc = -ENXIO;
goto err;
}
@@ -134,10 +134,10 @@ static int dcon_bus_stabilize(struct dcon_priv *dcon, int is_powered_down)
power_up:
if (is_powered_down) {
x = 1;
- x = olpc_ec_cmd(0x26, (unsigned char *) &x, 1, NULL, 0);
+ x = olpc_ec_cmd(0x26, (unsigned char *)&x, 1, NULL, 0);
if (x) {
- printk(KERN_WARNING "olpc-dcon: unable to force dcon "
- "to power up: %d!\n", x);
+ printk(KERN_WARNING "olpc-dcon: unable to force dcon to power up: %d!\n",
+ x);
return x;
}
msleep(10); /* we'll be conservative */
@@ -150,11 +150,10 @@ power_up:
x = dcon_read(dcon, DCON_REG_ID);
}
if (x < 0) {
- printk(KERN_ERR "olpc-dcon: unable to stabilize dcon's "
- "smbus, reasserting power and praying.\n");
+ printk(KERN_ERR "olpc-dcon: unable to stabilize dcon's smbus, reasserting power and praying.\n");
BUG_ON(olpc_board_at_least(olpc_board(0xc2)));
x = 0;
- olpc_ec_cmd(0x26, (unsigned char *) &x, 1, NULL, 0);
+ olpc_ec_cmd(0x26, (unsigned char *)&x, 1, NULL, 0);
msleep(100);
is_powered_down = 1;
goto power_up; /* argh, stupid hardware.. */
@@ -220,10 +219,10 @@ static void dcon_sleep(struct dcon_priv *dcon, bool sleep)
if (sleep) {
x = 0;
- x = olpc_ec_cmd(0x26, (unsigned char *) &x, 1, NULL, 0);
+ x = olpc_ec_cmd(0x26, (unsigned char *)&x, 1, NULL, 0);
if (x)
- printk(KERN_WARNING "olpc-dcon: unable to force dcon "
- "to power down: %d!\n", x);
+ printk(KERN_WARNING "olpc-dcon: unable to force dcon to power down: %d!\n",
+ x);
else
dcon->asleep = sleep;
} else {
@@ -232,8 +231,8 @@ static void dcon_sleep(struct dcon_priv *dcon, bool sleep)
dcon->disp_mode |= MODE_BL_ENABLE;
x = dcon_bus_stabilize(dcon, 1);
if (x)
- printk(KERN_WARNING "olpc-dcon: unable to reinit dcon"
- " hardware: %d!\n", x);
+ printk(KERN_WARNING "olpc-dcon: unable to reinit dcon hardware: %d!\n",
+ x);
else
dcon->asleep = sleep;
@@ -304,7 +303,7 @@ static void dcon_source_switch(struct work_struct *work)
switch (source) {
case DCON_SOURCE_CPU:
- printk("dcon_source_switch to CPU\n");
+ printk(KERN_INFO "dcon_source_switch to CPU\n");
/* Enable the scanline interrupt bit */
if (dcon_write(dcon, DCON_REG_MODE,
dcon->disp_mode | MODE_SCAN_INT))
@@ -599,7 +598,7 @@ static int dcon_fb_notifier(struct notifier_block *self,
struct fb_event *evdata = data;
struct dcon_priv *dcon = container_of(self, struct dcon_priv,
fbevent_nb);
- int *blank = (int *) evdata->data;
+ int *blank = (int *)evdata->data;
if (((event != FB_EVENT_BLANK) && (event != FB_EVENT_CONBLANK)) ||
dcon->ignore_fb_events)
return 0;
--
1.7.10
--
Jesper Juhl <jj@xxxxxxxxxxxxx> http://www.chaosbits.net/
Don't top-post http://www.catb.org/jargon/html/T/top-post.html
Plain text mails only, please.
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
