Move et1310_phy.h register defines into et131x.h and delete
et1310_phy.h
Signed-off-by: Mark Einon <mark.einon@xxxxxxxxx>
---
drivers/staging/et131x/et1310_phy.h | 290 -----------------------------------
drivers/staging/et131x/et131x.c | 1 -
drivers/staging/et131x/et131x.h | 227 +++++++++++++++++++++++++++
3 files changed, 227 insertions(+), 291 deletions(-)
delete mode 100644 drivers/staging/et131x/et1310_phy.h
diff --git a/drivers/staging/et131x/et1310_phy.h b/drivers/staging/et131x/et1310_phy.h
deleted file mode 100644
index feb5761..0000000
diff --git a/drivers/staging/et131x/et131x.c b/drivers/staging/et131x/et131x.c
index 60ff3bc..271ae31 100644
--- a/drivers/staging/et131x/et131x.c
+++ b/drivers/staging/et131x/et131x.c
@@ -83,7 +83,6 @@
#include <linux/random.h>
#include <linux/phy.h>
-#include "et1310_phy.h"
#include "et131x_adapter.h"
#include "et1310_tx.h"
#include "et1310_rx.h"
diff --git a/drivers/staging/et131x/et131x.h b/drivers/staging/et131x/et131x.h
index 8f61a72..84b274d 100644
--- a/drivers/staging/et131x/et131x.h
+++ b/drivers/staging/et131x/et131x.h
@@ -1447,3 +1447,230 @@ struct address_map {
u8 unused_exp_rom[4096]; /* MGS-size TBD */
u8 unused__[524288]; /* unused section of address map */
};
+
+/*
+ * Defines for generic MII registers 0x00 -> 0x0F can be found in
+ * include/linux/mii.h
+ */
+
+/* some defines for modem registers that seem to be 'reserved' */
+#define PHY_INDEX_REG 0x10
+#define PHY_DATA_REG 0x11
+#define PHY_MPHY_CONTROL_REG 0x12
+
+/* defines for specified registers */
+#define PHY_LOOPBACK_CONTROL 0x13 /* TRU_VMI_LOOPBACK_CONTROL_1_REG 19 */
+ /* TRU_VMI_LOOPBACK_CONTROL_2_REG 20 */
+#define PHY_REGISTER_MGMT_CONTROL 0x15 /* TRU_VMI_MI_SEQ_CONTROL_REG 21 */
+#define PHY_CONFIG 0x16 /* TRU_VMI_CONFIGURATION_REG 22 */
+#define PHY_PHY_CONTROL 0x17 /* TRU_VMI_PHY_CONTROL_REG 23 */
+#define PHY_INTERRUPT_MASK 0x18 /* TRU_VMI_INTERRUPT_MASK_REG 24 */
+#define PHY_INTERRUPT_STATUS 0x19 /* TRU_VMI_INTERRUPT_STATUS_REG 25 */
+#define PHY_PHY_STATUS 0x1A /* TRU_VMI_PHY_STATUS_REG 26 */
+#define PHY_LED_1 0x1B /* TRU_VMI_LED_CONTROL_1_REG 27 */
+#define PHY_LED_2 0x1C /* TRU_VMI_LED_CONTROL_2_REG 28 */
+ /* TRU_VMI_LINK_CONTROL_REG 29 */
+ /* TRU_VMI_TIMING_CONTROL_REG */
+
+/* MI Register 10: Gigabit basic mode status reg(Reg 0x0A) */
+#define ET_1000BT_MSTR_SLV 0x4000
+
+/* MI Register 16 - 18: Reserved Reg(0x10-0x12) */
+
+/* MI Register 19: Loopback Control Reg(0x13)
+ * 15: mii_en
+ * 14: pcs_en
+ * 13: pmd_en
+ * 12: all_digital_en
+ * 11: replica_en
+ * 10: line_driver_en
+ * 9-0: reserved
+ */
+
+/* MI Register 20: Reserved Reg(0x14) */
+
+/* MI Register 21: Management Interface Control Reg(0x15)
+ * 15-11: reserved
+ * 10-4: mi_error_count
+ * 3: reserved
+ * 2: ignore_10g_fr
+ * 1: reserved
+ * 0: preamble_supress_en
+ */
+
+/* MI Register 22: PHY Configuration Reg(0x16)
+ * 15: crs_tx_en
+ * 14: reserved
+ * 13-12: tx_fifo_depth
+ * 11-10: speed_downshift
+ * 9: pbi_detect
+ * 8: tbi_rate
+ * 7: alternate_np
+ * 6: group_mdio_en
+ * 5: tx_clock_en
+ * 4: sys_clock_en
+ * 3: reserved
+ * 2-0: mac_if_mode
+ */
+
+#define ET_PHY_CONFIG_TX_FIFO_DEPTH 0x3000
+
+#define ET_PHY_CONFIG_FIFO_DEPTH_8 0x0000
+#define ET_PHY_CONFIG_FIFO_DEPTH_16 0x1000
+#define ET_PHY_CONFIG_FIFO_DEPTH_32 0x2000
+#define ET_PHY_CONFIG_FIFO_DEPTH_64 0x3000
+
+/* MI Register 23: PHY CONTROL Reg(0x17)
+ * 15: reserved
+ * 14: tdr_en
+ * 13: reserved
+ * 12-11: downshift_attempts
+ * 10-6: reserved
+ * 5: jabber_10baseT
+ * 4: sqe_10baseT
+ * 3: tp_loopback_10baseT
+ * 2: preamble_gen_en
+ * 1: reserved
+ * 0: force_int
+ */
+
+/* MI Register 24: Interrupt Mask Reg(0x18)
+ * 15-10: reserved
+ * 9: mdio_sync_lost
+ * 8: autoneg_status
+ * 7: hi_bit_err
+ * 6: np_rx
+ * 5: err_counter_full
+ * 4: fifo_over_underflow
+ * 3: rx_status
+ * 2: link_status
+ * 1: automatic_speed
+ * 0: int_en
+ */
+
+#define ET_PHY_INT_MASK_AUTONEGSTAT 0x0100
+#define ET_PHY_INT_MASK_LINKSTAT 0x0004
+#define ET_PHY_INT_MASK_ENABLE 0x0001
+
+/* MI Register 25: Interrupt Status Reg(0x19)
+ * 15-10: reserved
+ * 9: mdio_sync_lost
+ * 8: autoneg_status
+ * 7: hi_bit_err
+ * 6: np_rx
+ * 5: err_counter_full
+ * 4: fifo_over_underflow
+ * 3: rx_status
+ * 2: link_status
+ * 1: automatic_speed
+ * 0: int_en
+ */
+
+/* MI Register 26: PHY Status Reg(0x1A)
+ * 15: reserved
+ * 14-13: autoneg_fault
+ * 12: autoneg_status
+ * 11: mdi_x_status
+ * 10: polarity_status
+ * 9-8: speed_status
+ * 7: duplex_status
+ * 6: link_status
+ * 5: tx_status
+ * 4: rx_status
+ * 3: collision_status
+ * 2: autoneg_en
+ * 1: pause_en
+ * 0: asymmetric_dir
+ */
+#define ET_PHY_AUTONEG_STATUS 0x1000
+#define ET_PHY_POLARITY_STATUS 0x0400
+#define ET_PHY_SPEED_STATUS 0x0300
+#define ET_PHY_DUPLEX_STATUS 0x0080
+#define ET_PHY_LSTATUS 0x0040
+#define ET_PHY_AUTONEG_ENABLE 0x0020
+
+/* MI Register 27: LED Control Reg 1(0x1B)
+ * 15-14: reserved
+ * 13-12: led_dup_indicate
+ * 11-10: led_10baseT
+ * 9-8: led_collision
+ * 7-4: reserved
+ * 3-2: pulse_dur
+ * 1: pulse_stretch1
+ * 0: pulse_stretch0
+ */
+
+/* MI Register 28: LED Control Reg 2(0x1C)
+ * 15-12: led_link
+ * 11-8: led_tx_rx
+ * 7-4: led_100BaseTX
+ * 3-0: led_1000BaseT
+ */
+#define ET_LED2_LED_LINK 0xF000
+#define ET_LED2_LED_TXRX 0x0F00
+#define ET_LED2_LED_100TX 0x00F0
+#define ET_LED2_LED_1000T 0x000F
+
+/* defines for LED control reg 2 values */
+#define LED_VAL_1000BT 0x0
+#define LED_VAL_100BTX 0x1
+#define LED_VAL_10BT 0x2
+#define LED_VAL_1000BT_100BTX 0x3 /* 1000BT on, 100BTX blink */
+#define LED_VAL_LINKON 0x4
+#define LED_VAL_TX 0x5
+#define LED_VAL_RX 0x6
+#define LED_VAL_TXRX 0x7 /* TX or RX */
+#define LED_VAL_DUPLEXFULL 0x8
+#define LED_VAL_COLLISION 0x9
+#define LED_VAL_LINKON_ACTIVE 0xA /* Link on, activity blink */
+#define LED_VAL_LINKON_RECV 0xB /* Link on, receive blink */
+#define LED_VAL_DUPLEXFULL_COLLISION 0xC /* Duplex on, collision blink */
+#define LED_VAL_BLINK 0xD
+#define LED_VAL_ON 0xE
+#define LED_VAL_OFF 0xF
+
+#define LED_LINK_SHIFT 12
+#define LED_TXRX_SHIFT 8
+#define LED_100TX_SHIFT 4
+
+/* MI Register 29 - 31: Reserved Reg(0x1D - 0x1E) */
+
+/* Defines for PHY access routines */
+
+/* Define bit operation flags */
+#define TRUEPHY_BIT_CLEAR 0
+#define TRUEPHY_BIT_SET 1
+#define TRUEPHY_BIT_READ 2
+
+/* Define read/write operation flags */
+#ifndef TRUEPHY_READ
+#define TRUEPHY_READ 0
+#define TRUEPHY_WRITE 1
+#define TRUEPHY_MASK 2
+#endif
+
+/* Define master/slave configuration values */
+#define TRUEPHY_CFG_SLAVE 0
+#define TRUEPHY_CFG_MASTER 1
+
+/* Define MDI/MDI-X settings */
+#define TRUEPHY_MDI 0
+#define TRUEPHY_MDIX 1
+#define TRUEPHY_AUTO_MDI_MDIX 2
+
+/* Define 10Base-T link polarities */
+#define TRUEPHY_POLARITY_NORMAL 0
+#define TRUEPHY_POLARITY_INVERTED 1
+
+/* Define auto-negotiation results */
+#define TRUEPHY_ANEG_NOT_COMPLETE 0
+#define TRUEPHY_ANEG_COMPLETE 1
+#define TRUEPHY_ANEG_DISABLED 2
+
+/* Define duplex advertisement flags */
+#define TRUEPHY_ADV_DUPLEX_NONE 0x00
+#define TRUEPHY_ADV_DUPLEX_FULL 0x01
+#define TRUEPHY_ADV_DUPLEX_HALF 0x02
+#define TRUEPHY_ADV_DUPLEX_BOTH \
+ (TRUEPHY_ADV_DUPLEX_FULL | TRUEPHY_ADV_DUPLEX_HALF)
+
--
1.7.6.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
