Hello Nicolas, On Fri, Mar 12, 2021 at 01:24:54PM +0100, Nicolas Saenz Julienne wrote: > Adds support to control the PWM bus available in official Raspberry Pi > PoE HAT. Only RPi's co-processor has access to it, so commands have to > be sent through RPi's firmware mailbox interface. > > Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx> > > --- > > Changes since v7: > - Remove unwarranted RPI_PWM_DEF_DUTY_REG usage > > Changes since v6: > - Use %pe > - Round divisions properly > - Use dev_err_probe() > - Pass check_patch > > Changes since v3: > - Rename compatible string to be more explicit WRT to bus's limitations > > Changes since v2: > - Use devm_rpi_firmware_get() > - Rename driver > - Small cleanups > > Changes since v1: > - Use default pwm bindings and get rid of xlate() function > - Correct spelling errors > - Correct apply() function > - Round values > - Fix divisions in arm32 mode > - Small cleanups > > drivers/pwm/Kconfig | 9 ++ > drivers/pwm/Makefile | 1 + > drivers/pwm/pwm-raspberrypi-poe.c | 206 ++++++++++++++++++++++++++++++ > 3 files changed, 216 insertions(+) > create mode 100644 drivers/pwm/pwm-raspberrypi-poe.c > > diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig > index a7a7a9f26aef..d3371ac7b871 100644 > --- a/drivers/pwm/Kconfig > +++ b/drivers/pwm/Kconfig > @@ -431,6 +431,15 @@ config PWM_PXA > To compile this driver as a module, choose M here: the module > will be called pwm-pxa. > > +config PWM_RASPBERRYPI_POE > + tristate "Raspberry Pi Firwmware PoE Hat PWM support" > + # Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only > + # happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE. > + depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE) > + help > + Enable Raspberry Pi firmware controller PWM bus used to control the > + official RPI PoE hat > + > config PWM_RCAR > tristate "Renesas R-Car PWM support" > depends on ARCH_RENESAS || COMPILE_TEST > diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile > index 4e35a55fa7b6..d3879619bd76 100644 > --- a/drivers/pwm/Makefile > +++ b/drivers/pwm/Makefile > @@ -39,6 +39,7 @@ obj-$(CONFIG_PWM_NTXEC) += pwm-ntxec.o > obj-$(CONFIG_PWM_OMAP_DMTIMER) += pwm-omap-dmtimer.o > obj-$(CONFIG_PWM_PCA9685) += pwm-pca9685.o > obj-$(CONFIG_PWM_PXA) += pwm-pxa.o > +obj-$(CONFIG_PWM_RASPBERRYPI_POE) += pwm-raspberrypi-poe.o > obj-$(CONFIG_PWM_RCAR) += pwm-rcar.o > obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o > obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o > diff --git a/drivers/pwm/pwm-raspberrypi-poe.c b/drivers/pwm/pwm-raspberrypi-poe.c > new file mode 100644 > index 000000000000..71ade5e55069 > --- /dev/null > +++ b/drivers/pwm/pwm-raspberrypi-poe.c > @@ -0,0 +1,206 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright 2020 Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx> 2021? > + * For more information on Raspberry Pi's PoE hat see: > + * https://www.raspberrypi.org/products/poe-hat/ Out of personal interest: Is this hat also able to power a RPi CM4? > + * Limitations: > + * - No disable bit, so a disabled PWM is simulated by duty_cycle 0 > + * - Only normal polarity > + * - Fixed 12.5 kHz period > + * > + * The current period is completed when HW is reconfigured. > + */ Other than that as mentioned in the previous round: This looks good, Reviewed-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx> What is your thought about how to get this series merged? At least input, staging, armsoc, clk, reset anf firmware are touched. Do you prepare a branch for merging in the relevant trees (once you have all the necessary Acks)? Best regards Uwe -- Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | https://www.pengutronix.de/ |
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
