On Wed, Mar 10, 2021 at 04:37:21PM +0100, Fabio Aiuto wrote: > fix the following checkpatch warnings: > > WARNING: Block comments use * on subsequent lines > + /* > + AMPDU_para [1:0]:Max AMPDU Len => 0:8k , 1:16k, 2:32k, 3:64k > -- > WARNING: Block comments use * on subsequent lines > +/* > +op_mode > > Signed-off-by: Fabio Aiuto <fabioaiuto83@xxxxxxxxx> > --- > drivers/staging/rtl8723bs/core/rtw_ap.c | 28 ++++++++++++------------- > 1 file changed, 14 insertions(+), 14 deletions(-) > > diff --git a/drivers/staging/rtl8723bs/core/rtw_ap.c b/drivers/staging/rtl8723bs/core/rtw_ap.c > index b6f944b37b08..3a0e4f64466a 100644 > --- a/drivers/staging/rtl8723bs/core/rtw_ap.c > +++ b/drivers/staging/rtl8723bs/core/rtw_ap.c > @@ -721,9 +721,9 @@ static void update_hw_ht_param(struct adapter *padapter) > > /* handle A-MPDU parameter field */ > /* Combine these two comments into one mult-line comment. > - AMPDU_para [1:0]:Max AMPDU Len => 0:8k , 1:16k, 2:32k, 3:64k > - AMPDU_para [4:2]:Min MPDU Start Spacing > - */ > + * AMPDU_para [1:0]:Max AMPDU Len => 0:8k , 1:16k, 2:32k, 3:64k > + * AMPDU_para [4:2]:Min MPDU Start Spacing > + */ > max_AMPDU_len = pmlmeinfo->HT_caps.u.HT_cap_element.AMPDU_para & 0x03; > > min_MPDU_spacing = ( > @@ -1815,17 +1815,17 @@ void update_beacon(struct adapter *padapter, u8 ie_id, u8 *oui, u8 tx) > } > > /* > -op_mode > -Set to 0 (HT pure) under the following conditions > - - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or > - - all STAs in the BSS are 20 MHz HT in 20 MHz BSS > -Set to 1 (HT non-member protection) if there may be non-HT STAs > - in both the primary and the secondary channel > -Set to 2 if only HT STAs are associated in BSS, > - however and at least one 20 MHz HT STA is associated > -Set to 3 (HT mixed mode) when one or more non-HT STAs are associated > - (currently non-GF HT station is considered as non-HT STA also) > -*/ > + *op_mode You need to have a space character after the '*'. /* * op_mode * Set to ... > + *Set to 0 (HT pure) under the following conditions > + * - all STAs in the BSS are 20/40 MHz HT in 20/40 MHz BSS or > + * - all STAs in the BSS are 20 MHz HT in 20 MHz BSS > + *Set to 1 (HT non-member protection) if there may be non-HT STAs > + * in both the primary and the secondary channel > + *Set to 2 if only HT STAs are associated in BSS, > + * however and at least one 20 MHz HT STA is associated > + *Set to 3 (HT mixed mode) when one or more non-HT STAs are associated > + * (currently non-GF HT station is considered as non-HT STA also) > + */ regards, dan carpenter _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
