Hi Lee,
Em Wed, 27 Jan 2021 11:05:37 +0000
Lee Jones <lee.jones@xxxxxxxxxx> escreveu:
> On Tue, 19 Jan 2021, Mauro Carvalho Chehab wrote:
>
> > This driver is ready for mainstream. So, move it out of staging.
> >
> Replied to an earlier submission where I was able to reply in-line.
Sorry! Infradead seemed to have some problem between Jan 26-27: emails
got late-delivered.
> > +static const struct mfd_cell hi6421v600_devs[] = {
> > + { .name = "hi6421v600-regulator", },
> > +};
>
> Where are the reset of the devices?
Not sure what you mean here.
This MFD device provides:
- an IRQ handler;
- several LDO lines used by a regulator driver.
The IRQ handler is properly initialized here, while the
regulators are initialized by the regulator driver. The initial
state of this device is set up by u-boot.
So, AFAIKT, there's no need to have any reset line
attached here.
-
Yet, I'm still figuring out how the PCIe chips at Hikey 970
should be properly initialized. So, I may need to add something
somewhere in order to properly reset and power up the Ethernet,
M.2 and PCIe 1x slot.
Those are linked to the LDO 33.
> > +static void hi6421_spmi_irq_mask(struct irq_data *d)
> > +{
> > + struct hi6421_spmi_pmic *pmic = irq_data_get_irq_chip_data(d);
> > + unsigned long flags;
> > + unsigned int data;
> > + u32 offset;
> > +
> > + offset = (irqd_to_hwirq(d) >> 3);
>
> Why 3?
No idea. I don't have any datasheets from this device.
> Probably better to define these shifts/masks rather than use
> magic numbers with no comments.
I'll change the above to:
#define HISI_IRQ_MASK GENMASK(1, 0)
offset = (irqd_to_hwirq(d) >> HISI_IRQ_MASK);
> > + regmap_read(pmic->map, offset, &data);
> > + data |= (1 << (irqd_to_hwirq(d) & 0x07));
>
> What are you doing here?
>
> Maybe improved defines will be enough. If not, please supply a
> suitable comment.
Again, no idea. The only documentation I had access to this chip is
at:
https://www.96boards.org/documentation/consumer/hikey/hikey970/
With doesn't mention any register details.
The driver itself came from the Linaro's 96boards git tree, with also
doesn't contain any register mapping.
> > + pr_debug("PMU IRQ address value:irq[0x%x] = 0x%x\n",
> > + SOC_PMIC_IRQ0_ADDR + i, pending);
>
> Again, is this actually useful to anyone now that the driver is nearly
> 10 years old. Particularly anyone who can't add a quick printk()
> during a debug session?
With regards to the debug stuff, I'm dropping everything.
On a side comment, I doubt that the driver has 10 years old ;-)
See, Hikey 970 uses Kirin 970 SoC, which it was launched in Sept, 2017.
The original version of this driver publicly debuted on this tree:
https://github.com/96boards-hikey/linux/blob/hikey970-v4.9/drivers/mfd/hisi_pmic_spmi.c
On a commit made on Feb, 2018.
Ok, Hi6421v600 is a separate silicon, probably derivative from
Hi6421 (used on Hikey 960). Its copyright mentions 2011, but
that's probably because the code itself came from older generations
of the regulator chipset.
-
Please see the enclosed patch for the new code after fixing the issues
you pointed. I'll re-submit it as a series once you're ok with the
code.
Thanks,
Mauro
[PATCH] mfd: hi6421-spmi-pmic: move driver from staging
This driver is ready for mainstream. So, move it out of staging.
PS.: I removed the staging part of this patch, just to make
easier for reviewing the code. I'll re-post it as a
proper series after receiving feedback from this version.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml b/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
new file mode 100644
index 000000000000..3b23ad56b31a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi6421-spmi-pmic.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/hisilicon,hi6421-spmi-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon 6421v600 SPMI PMIC
+
+maintainers:
+ - Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
+
+description: |
+ HiSilicon 6421v600 should be connected inside a MIPI System Power Management
+ (SPMI) bus. It provides interrupts and power supply.
+
+ The GPIO and interrupt settings are represented as part of the top-level PMIC
+ node.
+
+ The SPMI controller part is provided by
+ drivers/staging/hikey9xx/hisilicon,hisi-spmi-controller.yaml.
+
+properties:
+ $nodename:
+ pattern: "pmic@[0-9a-f]"
+
+ compatible:
+ const: hisilicon,hi6421v600-spmi
+
+ reg:
+ maxItems: 1
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupt-controller:
+ description:
+ Identify that the PMIC is capable of behaving as an interrupt controller.
+
+ gpios:
+ maxItems: 1
+
+ regulators:
+ type: object
+
+ properties:
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ '^ldo[0-9]+@[0-9a-f]$':
+ type: object
+
+ $ref: "/schemas/regulator/regulator.yaml#"
+
+required:
+ - compatible
+ - reg
+ - regulators
+
+additionalProperties: false
+
+examples:
+ - |
+ /* pmic properties */
+
+ pmic: pmic@0 {
+ compatible = "hisilicon,hi6421-spmi";
+ reg = <0 0>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ gpios = <&gpio28 0 0>;
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-boot-on;
+ };
+
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-boot-on;
+ };
+
+ ldo9: LDO9 {
+ regulator-name = "ldo9";
+ regulator-min-microvolt = <1750000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo15: LDO15 {
+ regulator-name = "ldo15";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo16: LDO16 {
+ regulator-name = "ldo16";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ };
+
+ ldo17: LDO17 {
+ regulator-name = "ldo17";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo33: LDO33 {
+ regulator-name = "ldo33";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ ldo34: LDO34 {
+ regulator-name = "ldo34";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index bdfce7b15621..d80ccbf50235 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -509,6 +509,21 @@ config MFD_HI6421_PMIC
menus in order to enable them.
We communicate with the Hi6421 via memory-mapped I/O.
+config MFD_HI6421_SPMI
+ tristate "HiSilicon Hi6421v600 SPMI PMU/Codec IC"
+ depends on OF
+ depends on SPMI
+ select MFD_CORE
+ help
+ Add support for HiSilicon Hi6421v600 SPMI PMIC. Hi6421 includes
+ multi-functions, such as regulators, RTC, codec, Coulomb counter,
+ etc.
+
+ This driver includes core APIs _only_. You have to select
+ individual components like voltage regulators under corresponding
+ menus in order to enable them.
+ We communicate with the Hi6421v600 via a SPMI bus.
+
config MFD_HI655X_PMIC
tristate "HiSilicon Hi655X series PMU/Codec IC"
depends on ARCH_HISI || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 14fdb188af02..b64e89ade44b 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -234,6 +234,7 @@ obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o
obj-$(CONFIG_MFD_IQS62X) += iqs62x.o
obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o
obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o
+obj-$(CONFIG_MFD_HI6421_SPMI) += hi6421-spmi-pmic.o
obj-$(CONFIG_MFD_HI655X_PMIC) += hi655x-pmic.o
obj-$(CONFIG_MFD_DLN2) += dln2.o
obj-$(CONFIG_MFD_RT5033) += rt5033.o
diff --git a/drivers/mfd/hi6421-spmi-pmic.c b/drivers/mfd/hi6421-spmi-pmic.c
new file mode 100644
index 000000000000..7a2c420f19da
--- /dev/null
+++ b/drivers/mfd/hi6421-spmi-pmic.c
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device driver for regulators in HISI PMIC IC
+ *
+ * Copyright (c) 2013 Linaro Ltd.
+ * Copyright (c) 2011 Hisilicon.
+ * Copyright (c) 2020-2021 Huawei Technologies Co., Ltd
+ */
+
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/hi6421-spmi-pmic.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spmi.h>
+
+enum hi6421_spmi_pmic_irq_list {
+ OTMP = 0,
+ VBUS_CONNECT,
+ VBUS_DISCONNECT,
+ ALARMON_R,
+ HOLD_6S,
+ HOLD_1S,
+ POWERKEY_UP,
+ POWERKEY_DOWN,
+ OCP_SCP_R,
+ COUL_R,
+ SIM0_HPD_R,
+ SIM0_HPD_F,
+ SIM1_HPD_R,
+ SIM1_HPD_F,
+ PMIC_IRQ_LIST_MAX,
+};
+
+#define HISI_IRQ_ARRAY 2
+#define HISI_IRQ_NUM (HISI_IRQ_ARRAY * 8)
+#define HISI_IRQ_MASK GENMASK(1, 0)
+
+#define SOC_PMIC_IRQ_MASK_0_ADDR 0x0202
+#define SOC_PMIC_IRQ0_ADDR 0x0212
+
+#define HISI_IRQ_KEY_NUM 0
+
+#define HISI_BITS 8
+#define HISI_IRQ_KEY_VALUE (BIT(POWERKEY_DOWN) | BIT(POWERKEY_UP))
+#define HISI_MASK GENMASK(HISI_BITS - 1, 0)
+
+static const struct mfd_cell hi6421v600_devs[] = {
+ { .name = "hi6421v600-regulator", },
+};
+
+static irqreturn_t hi6421_spmi_irq_handler(int irq, void *priv)
+{
+ struct hi6421_spmi_pmic *ddata = (struct hi6421_spmi_pmic *)priv;
+ unsigned long pending;
+ unsigned int in;
+ int i, offset;
+
+ for (i = 0; i < HISI_IRQ_ARRAY; i++) {
+ regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &in);
+ pending = HISI_MASK & in;
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, pending);
+
+ if (i == HISI_IRQ_KEY_NUM &&
+ (pending & HISI_IRQ_KEY_VALUE) == HISI_IRQ_KEY_VALUE) {
+ generic_handle_irq(ddata->irqs[POWERKEY_DOWN]);
+ generic_handle_irq(ddata->irqs[POWERKEY_UP]);
+ pending &= (~HISI_IRQ_KEY_VALUE);
+ }
+
+ if (!pending)
+ continue;
+
+ for_each_set_bit(offset, &pending, HISI_BITS)
+ generic_handle_irq(ddata->irqs[offset + i * HISI_BITS]);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static void hi6421_spmi_irq_mask(struct irq_data *d)
+{
+ struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
+ unsigned long flags;
+ unsigned int data;
+ u32 offset;
+
+ offset = (irqd_to_hwirq(d) >> HISI_IRQ_MASK);
+ offset += SOC_PMIC_IRQ_MASK_0_ADDR;
+
+ spin_lock_irqsave(&ddata->lock, flags);
+
+ regmap_read(ddata->regmap, offset, &data);
+ data |= (1 << (irqd_to_hwirq(d) & 0x07));
+ regmap_write(ddata->regmap, offset, data);
+
+ spin_unlock_irqrestore(&ddata->lock, flags);
+}
+
+static void hi6421_spmi_irq_unmask(struct irq_data *d)
+{
+ struct hi6421_spmi_pmic *ddata = irq_data_get_irq_chip_data(d);
+ u32 data, offset;
+ unsigned long flags;
+
+ offset = (irqd_to_hwirq(d) >> 3);
+ offset += SOC_PMIC_IRQ_MASK_0_ADDR;
+
+ spin_lock_irqsave(&ddata->lock, flags);
+
+ regmap_read(ddata->regmap, offset, &data);
+ data &= ~(1 << (irqd_to_hwirq(d) & 0x07));
+ regmap_write(ddata->regmap, offset, data);
+
+ spin_unlock_irqrestore(&ddata->lock, flags);
+}
+
+static struct irq_chip hi6421_spmi_pmu_irqchip = {
+ .name = "hisi-irq",
+ .irq_mask = hi6421_spmi_irq_mask,
+ .irq_unmask = hi6421_spmi_irq_unmask,
+ .irq_disable = hi6421_spmi_irq_mask,
+ .irq_enable = hi6421_spmi_irq_unmask,
+};
+
+static int hi6421_spmi_irq_map(struct irq_domain *d, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct hi6421_spmi_pmic *ddata = d->host_data;
+
+ irq_set_chip_and_handler_name(virq, &hi6421_spmi_pmu_irqchip,
+ handle_simple_irq, "hisi");
+ irq_set_chip_data(virq, ddata);
+ irq_set_irq_type(virq, IRQ_TYPE_NONE);
+
+ return 0;
+}
+
+static const struct irq_domain_ops hi6421_spmi_domain_ops = {
+ .map = hi6421_spmi_irq_map,
+ .xlate = irq_domain_xlate_twocell,
+};
+
+static void hi6421_spmi_pmic_irq_init(struct hi6421_spmi_pmic *ddata)
+{
+ int i;
+ unsigned int pending;
+
+ for (i = 0; i < HISI_IRQ_ARRAY; i++)
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ_MASK_0_ADDR + i,
+ HISI_MASK);
+
+ for (i = 0; i < HISI_IRQ_ARRAY; i++) {
+ regmap_read(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i, &pending);
+ regmap_write(ddata->regmap, SOC_PMIC_IRQ0_ADDR + i,
+ HISI_MASK);
+ }
+}
+
+static const struct regmap_config regmap_config = {
+ .reg_bits = 16,
+ .val_bits = HISI_BITS,
+ .max_register = 0xffff,
+ .fast_io = true
+};
+
+static int hi6421_spmi_pmic_probe(struct spmi_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct hi6421_spmi_pmic *ddata;
+ unsigned int virq;
+ int ret, i;
+
+ ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
+ if (!ddata)
+ return -ENOMEM;
+
+ ddata->regmap = devm_regmap_init_spmi_ext(pdev, ®map_config);
+ if (IS_ERR(ddata->regmap))
+ return PTR_ERR(ddata->regmap);
+
+ spin_lock_init(&ddata->lock);
+
+ ddata->dev = dev;
+
+ ddata->gpio = of_get_gpio(np, 0);
+ if (ddata->gpio < 0)
+ return ddata->gpio;
+
+ if (!gpio_is_valid(ddata->gpio))
+ return -EINVAL;
+
+ ret = devm_gpio_request_one(dev, ddata->gpio, GPIOF_IN, "pmic");
+ if (ret < 0) {
+ dev_err(dev, "Failed to request gpio%d\n", ddata->gpio);
+ return ret;
+ }
+
+ ddata->irq = gpio_to_irq(ddata->gpio);
+
+ hi6421_spmi_pmic_irq_init(ddata);
+
+ ddata->irqs = devm_kzalloc(dev, HISI_IRQ_NUM * sizeof(int), GFP_KERNEL);
+ if (!ddata->irqs)
+ return -ENOMEM;
+
+ ddata->domain = irq_domain_add_simple(np, HISI_IRQ_NUM, 0,
+ &hi6421_spmi_domain_ops, ddata);
+ if (!ddata->domain) {
+ dev_err(dev, "Failed to create IRQ domain\n");
+ return -ENODEV;
+ }
+
+ for (i = 0; i < HISI_IRQ_NUM; i++) {
+ virq = irq_create_mapping(ddata->domain, i);
+ if (!virq) {
+ dev_err(dev, "Failed to map H/W IRQ\n");
+ return -ENOSPC;
+ }
+ ddata->irqs[i] = virq;
+ }
+
+ ret = request_threaded_irq(ddata->irq, hi6421_spmi_irq_handler, NULL,
+ IRQF_TRIGGER_LOW | IRQF_SHARED | IRQF_NO_SUSPEND,
+ "pmic", ddata);
+ if (ret < 0) {
+ dev_err(dev, "Failed to start IRQ handling thread: error %d\n",
+ ret);
+ return ret;
+ }
+
+ dev_set_drvdata(&pdev->dev, ddata);
+
+ ret = devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_NONE,
+ hi6421v600_devs, ARRAY_SIZE(hi6421v600_devs),
+ NULL, 0, NULL);
+ if (ret < 0)
+ dev_err(dev, "Failed to add child devices: %d\n", ret);
+
+ return ret;
+}
+
+static void hi6421_spmi_pmic_remove(struct spmi_device *pdev)
+{
+ struct hi6421_spmi_pmic *ddata = dev_get_drvdata(&pdev->dev);
+
+ free_irq(ddata->irq, ddata);
+}
+
+static const struct of_device_id pmic_spmi_id_table[] = {
+ { .compatible = "hisilicon,hi6421-spmi" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, pmic_spmi_id_table);
+
+static struct spmi_driver hi6421_spmi_pmic_driver = {
+ .driver = {
+ .name = "hi6421-spmi-pmic",
+ .of_match_table = pmic_spmi_id_table,
+ },
+ .probe = hi6421_spmi_pmic_probe,
+ .remove = hi6421_spmi_pmic_remove,
+};
+module_spmi_driver(hi6421_spmi_pmic_driver);
+
+MODULE_DESCRIPTION("HiSilicon Hi6421v600 SPMI PMIC driver");
+MODULE_LICENSE("GPL v2");
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
