On Wed, Dec 09, 2020 at 03:42:06PM +0300, Dan Carpenter wrote:
> Change the From email header to say your name.
>
> The patch is corrupted and can't be applied. Please read the first
> paragraphs of Documentation/process/email-clients.rst
>
> This driver is pretty small and it might be easier to clean it up first
> before merging it into staging. Run checkpatch.pl --strict on the
> driver.
>
> > --- /dev/null
> > +++ b/drivers/staging/si4455/si4455.c
> > @@ -0,0 +1,1465 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (C) 2020 József Horváth <info@xxxxxxxxxxx>
> > + *
> > + */
> > +#include <linux/bitops.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/device.h>
> > +#include <linux/gpio/driver.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > +#include <linux/regmap.h>
> > +#include <linux/serial_core.h>
> > +#include <linux/serial.h>
> > +#include <linux/tty.h>
> > +#include <linux/tty_flip.h>
> > +#include <linux/spi/spi.h>
> > +#include <linux/uaccess.h>
> > +#include "si4455_api.h"
> > +
> > +#define PORT_SI4455 1096
> > +#define SI4455_NAME "si4455"
> > +#define SI4455_MAJOR 432
> > +#define SI4455_MINOR 567
> > +#define SI4455_UART_NRMAX 1
> > +#define SI4455_FIFO_SIZE 64
> > +
> > +#define SI4455_CMD_ID_EZCONFIG_CHECK 0x19
> > +#define SI4455_CMD_ID_PART_INFO 0x01
> > +#define SI4455_CMD_REPLY_COUNT_PART_INFO 9
> > +#define SI4455_CMD_ID_GET_INT_STATUS 0x20
> > +#define SI4455_CMD_REPLY_COUNT_GET_INT_STATUS 8
> > +#define SI4455_CMD_ID_FIFO_INFO 0x15
> > +#define SI4455_CMD_ARG_COUNT_FIFO_INFO 2
> > +#define SI4455_CMD_REPLY_COUNT_FIFO_INFO 2
> > +#define SI4455_CMD_FIFO_INFO_ARG_TX_BIT 0x01
> > +#define SI4455_CMD_FIFO_INFO_ARG_RX_BIT 0x02
> > +#define SI4455_CMD_ID_READ_CMD_BUFF 0x44
> > +#define SI4455_CMD_ID_READ_RX_FIFO 0x77
> > +#define SI4455_CMD_ID_WRITE_TX_FIFO 0x66
> > +#define SI4455_CMD_ID_START_RX 0x32
> > +#define SI4455_CMD_ARG_COUNT_START_RX 8
> > +#define SI4455_CMD_START_RX_ARG_RXTIMEOUT_STATE_ENUM_RX 8
> > +#define SI4455_CMD_START_RX_ARG_RXVALID_STATE_ENUM_RX 8
> > +#define SI4455_CMD_START_RX_ARG_RXINVALID_STATE_ENUM_RX 8
> > +#define SI4455_CMD_ID_START_TX 0x31
> > +#define SI4455_CMD_ARG_COUNT_START_TX 5
> > +#define SI4455_CMD_ID_CHANGE_STATE 0x34
> > +#define SI4455_CMD_ARG_COUNT_CHANGE_STATE 2
> > +#define SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY 3
> > +#define SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_MASK 0x08
> > +#define SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_BIT 0x08
> > +#define SI4455_CMD_GET_INT_STATUS_REP_PACKET_SENT_PEND_BIT 0x20
> > +#define SI4455_CMD_GET_INT_STATUS_REP_PACKET_RX_PEND_BIT 0x10
> > +#define SI4455_CMD_GET_INT_STATUS_REP_CRC_ERROR_BIT 0x08
>
> These names are unreadably long and just make the code messy.
>
> > +#define SI4455_CMD_ID_GET_MODEM_STATUS 0x22
> > +#define SI4455_CMD_ARG_COUNT_GET_MODEM_STATUS 2
> > +#define SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS 8
> > +
> > +struct si4455_part_info {
> > + u8 CHIPREV;
> > + u16 PART;
> > + u8 PBUILD;
> > + u16 ID;
> > + u8 CUSTOMER;
> > + u8 ROMID;
> > + u8 BOND;
>
> Also the huge gap between the type and the struct member makes it
> hard to read.
>
> u8 chip_rev;
> u16 part;
> u8 pbuild;
>
> etc.
>
> > +};
> > +
> > +struct si4455_int_status {
> > + u8 INT_PEND;
> > + u8 INT_STATUS;
> > + u8 PH_PEND;
> > + u8 PH_STATUS;
> > + u8 MODEM_PEND;
> > + u8 MODEM_STATUS;
> > + u8 CHIP_PEND;
> > + u8 CHIP_STATUS;
> > +};
> > +
> > +struct si4455_modem_status {
> > + u8 MODEM_PEND;
> > + u8 MODEM_STATUS;
> > + u8 CURR_RSSI;
> > + u8 LATCH_RSSI;
> > + u8 ANT1_RSSI;
> > + u8 ANT2_RSSI;
> > + u16 AFC_FREQ_OFFSET;
> > +};
> > +
> > +struct si4455_fifo_info {
> > + u8 RX_FIFO_COUNT;
> > + u8 TX_FIFO_SPACE;
> > +};
> > +
> > +struct si4455_one {
> > + struct uart_port port;
> > + struct work_struct tx_work;
> > +};
> > +
> > +struct si4455_port {
> > + struct mutex mutex;
> > + int power_count;
> > + struct gpio_desc *shdn_gpio;
> > + struct si4455_part_info part_info;
> > + struct si4455_modem_status modem_status;
> > + struct si4455_iocbuff configuration;
> > + struct si4455_iocbuff patch;
> > + u32 tx_channel;
> > + u32 rx_channel;
> > + u32 package_size;
> > + bool configured;
> > + bool tx_pending;
> > + bool rx_pending;
> > + u32 current_rssi;
> > + struct si4455_one one;
> > +};
>
> Since the struct is not defined by the spec then don't bother aligning
> the members. It just makes changing the code complicated because you
> have to re-align stuff. Just put a single space between the type and
> the name.
>
>
> > +
> > +static struct uart_driver si4455_uart = {
> > + .owner = THIS_MODULE,
> > + .driver_name = SI4455_NAME,
> > +#ifdef CONFIG_DEVFS_FS
> > + .dev_name = "ttySI%d",
> > +#else
> > + .dev_name = "ttySI",
> > +#endif
> > + .major = SI4455_MAJOR,
> > + .minor = SI4455_MINOR,
> > + .nr = SI4455_UART_NRMAX,
> > +};
> > +
> > +static int si4455_get_response(struct uart_port *port,
> > + int length,
> > + u8 *data);
>
> Remove unecessary declarations like this.
>
> > +static int si4455_send_command(struct uart_port *port,
> > + int length,
> > + u8 *data);
> > +static int si4455_send_command_get_response(struct uart_port *port,
> > + int outLength,
> > + u8 *outData,
> > + int inLength,
> > + u8 *inData);
> > +static int si4455_read_data(struct uart_port *port,
> > + u8 command,
> > + int pollCts,
> > + int length,
> > + u8 *data);
> > +static int si4455_write_data(struct uart_port *port,
> > + u8 command,
> > + int pollCts,
> > + int length,
> > + u8 *data);
> > +static int si4455_poll_cts(struct uart_port *port);
> > +static void si4455_set_power(struct si4455_port *priv,
> > + int on);
> > +static int si4455_get_part_info(struct uart_port *port,
> > + struct si4455_part_info *result);
> > +
> > +static int si4455_get_response(struct uart_port *port,
> > + int length,
> > + u8 *data)
> > +{
> > + int ret = -EIO;
>
> Remove unecessary initializations. It disables static checkers' ability
> to find uninitialized variable bugs so it leads to bugs.
>
> > + u8 dataOut[] = { SI4455_CMD_ID_READ_CMD_BUFF };
> > + u8 *dataIn = devm_kzalloc(port->dev, 1 + length, GFP_KERNEL);
>
> Never put functions which can fail in the declaration block. It leads
> to "forgot to check for NULL bugs" which is the case here.
>
> Don't use devm_ for this. It has a different lifetime. Use normal
> kzalloc().
>
> > + struct spi_transfer xfer[] = {
> > + {
> > + .tx_buf = dataOut,
> > + .len = sizeof(dataOut),
> > + }, {
> > + .rx_buf = dataIn,
> > + .len = 1 + length,
> > + }
> > + };
> > + int errCnt = 10000;
> > +
> > + while (errCnt > 0) {
>
> while (--cnt > 9) {
>
> > + dataOut[0] = SI4455_CMD_ID_READ_CMD_BUFF;
> > + ret = spi_sync_transfer(to_spi_device(port->dev),
> > + xfer,
> > + ARRAY_SIZE(xfer));
> > + if (ret == 0) {
>
> Always do Error Handling as opposed to success handling.
>
> if (ret)
> break;
>
> > + if (dataIn[0] == 0xFF) {
> > + if ((length > 0) && (data != NULL)) {
> > + memcpy(data, &dataIn[1], length);
> > + } else {
> > + if (length > 0)
> > + ret = -EINVAL;
> > + }
> > + break;
> > + }
> > + usleep_range(100, 200);
> > + } else {
> > + break;
> > + }
> > + errCnt--;
> > + }
> > + if (errCnt == 0) {
> > + dev_err(port->dev, "si4455_poll_cts:errCnt==%i", errCnt);
> > + ret = -EIO;
> > + }
> > + if (dataIn != NULL)
> > + devm_kfree(port->dev, dataIn);
> > + return ret;
> > +}
> > +
> > +static int si4455_send_command(struct uart_port *port,
> > + int length,
> > + u8 *data)
> > +{
> > + int ret;
> > +
> > + ret = si4455_poll_cts(port);
> > + if (ret == 0) {
>
> ret = si4455_poll_cts(port);
> if (ret) {
> dev_err(port->dev, "%s: si4455_poll_cts error(%i)", __func__,
> ret);
> return ret;
> }
>
> All the checks need to be reversed. The printk only needs two lines.
>
>
> > + ret = spi_write(to_spi_device(port->dev), data, length);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: spi_write error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_poll_cts error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_send_command_get_response(struct uart_port *port,
> > + int outLength,
> > + u8 *outData,
> > + int inLength,
> > + u8 *inData)
> > +{
> > + int ret;
> > +
> > + ret = si4455_send_command(port, outLength, outData);
> > + if (!ret) {
> > + ret = si4455_get_response(port, inLength, inData);
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_read_data(struct uart_port *port,
> > + u8 command,
> > + int pollCts,
> > + int length,
> > + u8 *data)
> > +{
> > + int ret = 0;
> > + u8 dataOut[] = { command };
> > + struct spi_transfer xfer[] = {
> > + {
> > + .tx_buf = dataOut,
> > + .len = sizeof(dataOut),
> > + }, {
> > + .rx_buf = data,
> > + .len = length,
> > + }
> > + };
> > +
> > + if (pollCts)
> > + ret = si4455_poll_cts(port);
>
> if (poll) {
> ret = si4455_poll_cts(port);
> if (ret)
> return ret;
> }
>
> > +
> > + if (ret == 0) {
> > + ret = spi_sync_transfer(to_spi_device(port->dev),
> > + xfer,
> > + ARRAY_SIZE(xfer));
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: spi_sync_transfer error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_write_data(struct uart_port *port,
> > + u8 command,
> > + int pollCts,
> > + int length,
> > + u8 *data)
> > +{
> > + int ret = 0;
> > + u8 *dataOut = NULL;
> > +
> > + if (pollCts)
> > + ret = si4455_poll_cts(port);
> > +
> > + if (ret == 0) {
> > + dataOut = devm_kzalloc(port->dev, 1 + length, GFP_KERNEL);
>
> Use vanilla kzalloc().
>
> > + if (dataOut != NULL) {
> > + dataOut[0] = command;
> > + memcpy(&dataOut[1], data, length);
> > + ret = spi_write(to_spi_device(port->dev),
> > + dataOut,
> > + 1 + length);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: spi_write error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + } else {
> > + dev_err(port->dev,
> > + "%s: devm_kzalloc error",
> > + __func__);
> > + ret = -ENOMEM;
> > + }
> > + }
> > + if (dataOut != NULL)
> > + devm_kfree(port->dev, dataOut);
> > +
> > + return ret;
> > +}
> > +
> > +static int si4455_poll_cts(struct uart_port *port)
> > +{
> > + return si4455_get_response(port, 0, NULL);
> > +}
> > +
> > +static void si4455_set_power(struct si4455_port *priv,
> > + int on)
> > +{
> > + if (priv->shdn_gpio) {
>
> Reverse this test:
>
> if (!priv->shdn_gpio)
> return;
>
> > + if (on) {
> > + gpiod_direction_output(priv->shdn_gpio, 0);
> > + usleep_range(4000, 5000);
> > + gpiod_set_value(priv->shdn_gpio, 1);
> > + usleep_range(4000, 5000);
> > + } else {
> > + gpiod_direction_output(priv->shdn_gpio, 0);
> > + }
> > + }
> > +}
> > +
> > +static int si4455_s_power(struct device *dev,
> > + int on)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(dev);
> > +
> > + dev_dbg(dev, "%s(on=%d)\n", __func__, on);
> > + if (s->power_count == !on)
> > + si4455_set_power(s, on);
> > + s->power_count += on ? 1 : -1;
> > + WARN_ON(s->power_count < 0);
> > +
> > + return 0;
> > +}
> > +
> > +static int si4455_get_part_info(struct uart_port *port,
> > + struct si4455_part_info *result)
> > +{
> > + int ret;
> > + u8 dataOut[] = { SI4455_CMD_ID_PART_INFO };
> > + u8 dataIn[SI4455_CMD_REPLY_COUNT_PART_INFO];
> > +
> > + ret = si4455_send_command_get_response(port,
> > + sizeof(dataOut),
> > + dataOut,
> > + sizeof(dataIn),
> > + dataIn);
>
> This can fit on two lines:
>
> ret = si4455_send_command_get_response(port, sizeof(dataOut), dataOut,
> sizeof(dataIn), dataIn);
>
>
> > + if (ret == 0) {
> > + result->CHIPREV = dataIn[0];
> > + memcpy(&result->PART, &dataIn[1], sizeof(result->PART));
> > + result->PBUILD = dataIn[3];
> > + memcpy(&result->ID, &dataIn[4], sizeof(result->ID));
> > + result->CUSTOMER = dataIn[6];
> > + result->ROMID = dataIn[7];
> > + result->BOND = dataIn[8];
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command_get_response error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_get_int_status(struct uart_port *port,
> > + u8 phClear,
> > + u8 modemClear,
> > + u8 chipClear,
> > + struct si4455_int_status *result)
> > +{
> > + int ret;
> > + u8 dataOut[] = {
> > + SI4455_CMD_ID_GET_INT_STATUS,
> > + phClear,
> > + modemClear,
> > + chipClear
> > + };
> > + u8 dataIn[SI4455_CMD_REPLY_COUNT_GET_INT_STATUS];
> > +
> > + ret = si4455_send_command_get_response(port,
> > + sizeof(dataOut),
> > + dataOut,
> > + sizeof(dataIn),
> > + dataIn);
> > + if (ret == 0) {
> > + result->INT_PEND = dataIn[0];
> > + result->INT_STATUS = dataIn[1];
> > + result->PH_PEND = dataIn[2];
> > + result->PH_STATUS = dataIn[3];
> > + result->MODEM_PEND = dataIn[4];
> > + result->MODEM_STATUS = dataIn[5];
> > + result->CHIP_PEND = dataIn[6];
> > + result->CHIP_STATUS = dataIn[7];
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command_get_response error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_get_modem_status(struct uart_port *port,
> > + u8 modemClear,
> > + struct si4455_modem_status *result)
> > +{
> > + int ret;
> > + u8 dataOut[] = {
> > + SI4455_CMD_ID_GET_MODEM_STATUS,
> > + modemClear,
> > + };
> > + u8 dataIn[SI4455_CMD_REPLY_COUNT_GET_MODEM_STATUS];
> > +
> > + ret = si4455_send_command_get_response(port,
> > + sizeof(dataOut),
> > + dataOut,
> > + sizeof(dataIn),
> > + dataIn);
> > + if (ret == 0) {
> > + result->MODEM_PEND = dataIn[0];
> > + result->MODEM_STATUS = dataIn[1];
> > + result->CURR_RSSI = dataIn[2];
> > + result->LATCH_RSSI = dataIn[3];
> > + result->ANT1_RSSI = dataIn[4];
> > + result->ANT2_RSSI = dataIn[5];
> > + memcpy(&result->AFC_FREQ_OFFSET,
> > + &dataIn[6],
> > + sizeof(result->AFC_FREQ_OFFSET));
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command_get_response error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_fifo_info(struct uart_port *port,
> > + u8 fifo,
> > + struct si4455_fifo_info *result)
> > +{
> > + int ret = 0;
> > + u8 dataOut[SI4455_CMD_ARG_COUNT_FIFO_INFO] = {
> > + SI4455_CMD_ID_FIFO_INFO, fifo
> > + };
> > + u8 dataIn[SI4455_CMD_REPLY_COUNT_FIFO_INFO] = { 0 };
> > +
> > + ret = si4455_send_command_get_response(port,
> > + sizeof(dataOut),
> > + dataOut,
> > + sizeof(dataIn),
> > + dataIn);
> > + if (ret == 0) {
> > + result->RX_FIFO_COUNT = dataIn[0];
> > + result->TX_FIFO_SPACE = dataIn[1];
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command_get_response error(%i)",
> > + __func__,
> > + ret);
> > + }
> > + return ret;
> > +}
> > +
> > +static int si4455_read_rx_fifo(struct uart_port *port,
> > + int length,
> > + u8 *data)
> > +{
> > + return si4455_read_data(port,
> > + SI4455_CMD_ID_READ_RX_FIFO,
> > + 0,
> > + length,
> > + data);
> > +}
> > +
> > +static int si4455_write_tx_fifo(struct uart_port *port,
> > + int length,
> > + u8 *data)
> > +{
> > + return si4455_write_data(port,
> > + SI4455_CMD_ID_WRITE_TX_FIFO,
> > + 0,
> > + length,
> > + data);
> > +}
> > +
> > +static int si4455_rx(struct uart_port *port,
> > + u32 channel,
> > + u8 condition,
> > + u16 length,
> > + u8 nextState1,
> > + u8 nextState2,
> > + u8 nextState3)
> > +{
> > + u8 dataOut[SI4455_CMD_ARG_COUNT_START_RX];
> > +
> > + dataOut[0] = SI4455_CMD_ID_START_RX;
> > + dataOut[1] = channel;
> > + dataOut[2] = condition;
> > + dataOut[3] = (u8)(length >> 8);
> > + dataOut[4] = (u8)(length);
> > + dataOut[5] = nextState1;
> > + dataOut[6] = nextState2;
> > + dataOut[7] = nextState3;
> > +
> > + return si4455_send_command(port,
> > + SI4455_CMD_ARG_COUNT_START_RX,
> > + dataOut);
> > +}
> > +
> > +static int si4455_tx(struct uart_port *port,
> > + u8 channel,
> > + u8 condition,
> > + u16 length)
> > +{
> > + u8 dataOut[/*6*/ SI4455_CMD_ARG_COUNT_START_TX];
> > +
> > + dataOut[0] = SI4455_CMD_ID_START_TX;
> > + dataOut[1] = channel;
> > + dataOut[2] = condition;
> > + dataOut[3] = (u8)(length >> 8);
> > + dataOut[4] = (u8)(length);
> > + /*TODO: radioCmd[5] = 0x44; in case of rev c2a*/
> > +
> > + return si4455_send_command(port,
> > + /*6*/ SI4455_CMD_ARG_COUNT_START_TX,
> > + dataOut);
> > +}
> > +
> > +static int si4455_change_state(struct uart_port *port,
> > + u8 nextState1)
> > +{
> > + u8 dataOut[SI4455_CMD_ARG_COUNT_CHANGE_STATE];
> > +
> > + dataOut[0] = SI4455_CMD_ID_CHANGE_STATE;
> > + dataOut[1] = (u8)nextState1;
> > +
> > + return si4455_send_command(port,
> > + SI4455_CMD_ARG_COUNT_CHANGE_STATE,
> > + dataOut);
> > +}
> > +
> > +static int si4455_begin_tx(struct uart_port *port,
> > + u32 channel,
> > + int length,
> > + u8 *data)
> > +{
> > + int ret = 0;
> > + struct si4455_int_status intStatus = { 0 };
> > + struct si4455_fifo_info fifoInfo = { 0 };
> > +
> > + dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
> > + if ((length > SI4455_FIFO_SIZE) || (length < 0))
> > + ret = -EINVAL;
> > +
> > + if (ret == 0) {
> > + ret = si4455_change_state(port,
> > + SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_change_state error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_get_int_status error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_fifo_info(port,
> > + SI4455_CMD_FIFO_INFO_ARG_TX_BIT,
> > + &fifoInfo);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_fifo_info error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_write_tx_fifo(port, (u16)length, data);
>
> No need to cast this.
>
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_write_tx_fifo error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
>
> Just return directly. Do nothing gotos just end up introducing "Forgot
> to set the error code" bugs.
>
> > + }
> > + ret = si4455_tx(port,
> > + (u8)channel,
> > + 0x30,
> > + (u16)length);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_tx error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + }
> > +end:
> > + return ret;
> > +}
> > +
> > +static int si4455_end_tx(struct uart_port *port)
> > +{
> > + int ret = 0;
> > + struct si4455_int_status intStatus = { 0 };
> > +
> > + ret = si4455_change_state(port,
> > + SI4455_CMD_CHANGE_STATE_ARG_NEW_STATE_ENUM_READY);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_change_state error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_get_int_status error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > +end:
> > + return ret;
> > +}
> > +
> > +static int si4455_begin_rx(struct uart_port *port,
> > + u32 channel,
> > + u32 length)
> > +{
> > + int ret = 0;
> > + struct si4455_int_status intStatus = { 0 };
> > + struct si4455_fifo_info fifoInfo = { 0 };
> > +
> > + dev_dbg(port->dev, "%s(%u, %u)", __func__, channel, length);
> > + ret = si4455_get_int_status(port, 0, 0, 0, &intStatus);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_get_int_status error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_fifo_info(port,
> > + SI4455_CMD_FIFO_INFO_ARG_RX_BIT,
> > + &fifoInfo);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_fifo_info error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > + ret = si4455_rx(port,
> > + channel,
> > + 0x00,
> > + length,
> > + SI4455_CMD_START_RX_ARG_RXTIMEOUT_STATE_ENUM_RX,
> > + SI4455_CMD_START_RX_ARG_RXVALID_STATE_ENUM_RX,
> > + SI4455_CMD_START_RX_ARG_RXINVALID_STATE_ENUM_RX);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_rx error(%i)",
> > + __func__,
> > + ret);
> > + goto end;
> > + }
> > +end:
> > + return ret;
> > +}
> > +
> > +static int si4455_end_rx(struct uart_port *port,
> > + u32 length,
> > + u8 *data)
> > +{
> > + return si4455_read_rx_fifo(port, length, data);
> > +}
> > +
> > +static int si4455_configure(struct uart_port *port,
> > + u8 *configurationData)
> > +{
> > + int ret = 0;
> > + u8 col;
> > + u8 response;
> > + u8 numOfBytes;
> > + struct si4455_int_status intStatus = { 0 };
> > + u8 radioCmd[16u];
> > +
> > + /* While cycle as far as the pointer points to a command */
> > + while (*configurationData != 0x00) {
> > + /* Commands structure in the array:
> > + * --------------------------------
> > + * LEN | <LEN length of data>
> > + */
> > + numOfBytes = *configurationData++;
> > + dev_dbg(port->dev,
> > + "%s: numOfBytes(%u)",
> > + __func__,
> > + numOfBytes);
> > + if (numOfBytes > 16u) {
> > + /* Initial configuration of Si4x55 */
> > + if (SI4455_CMD_ID_WRITE_TX_FIFO
> > + == *configurationData) {
> > + if (numOfBytes > 128u) {
> > + /* Number of command bytes exceeds
> > + * maximal allowable length
> > + */
> > + dev_err(port->dev,
> > + "%s: command length
> > error(%i)",
> > + __func__,
> > + numOfBytes);
> > + ret = -EINVAL;
> > + break;
> > + }
> > +
> > + /* Load array to the device */
> > + configurationData++;
> > + ret = si4455_write_data(port,
> > + SI4455_CMD_ID_WRITE_TX_FIFO,
> > + 1,
> > + numOfBytes - 1,
> > + configurationData);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_write_data
> > error(%i)",
> > + __func__,
> > + ret);
> > + break;
> > + }
> > +
> > + /* Point to the next command */
> > + configurationData += numOfBytes - 1;
> > +
> > + /* Continue command interpreter */
> > + continue;
> > + } else {
> > + /* Number of command bytes exceeds
> > + * maximal allowable length
> > + */
> > + ret = -EINVAL;
> > + break;
> > + }
> > + }
> > +
> > + for (col = 0u; col < numOfBytes; col++) {
> > + radioCmd[col] = *configurationData;
> > + configurationData++;
> > + }
> > +
> > + dev_dbg(port->dev,
> > + "%s: radioCmd[0](%u)",
> > + __func__,
> > + radioCmd[0]);
> > + ret = si4455_send_command_get_response(port,
> > + numOfBytes,
> > + radioCmd,
> > + 1,
> > + &response);
> > + if (ret) {
> > + dev_err(port->dev,
> > + "%s: si4455_send_command_get_response
> > error(%i)",
> > + __func__,
> > + ret);
> > + break;
> > + }
> > +
> > + /* Check response byte of EZCONFIG_CHECK command */
> > + if (radioCmd[0] == SI4455_CMD_ID_EZCONFIG_CHECK) {
> > + if (response) {
> > + /* Number of command bytes exceeds
> > + * maximal allowable length
> > + */
> > + ret = -EIO;
> > + dev_err(port->dev,
> > + "%s: EZConfig check error(%i)",
> > + __func__,
> > + radioCmd[0]);
> > + break;
> > + }
> > + }
> > +
> > + /* Get and clear all interrupts. An error has occurred...
> > */
> > + si4455_get_int_status(port, 0, 0, 0, &intStatus);
> > + if (intStatus.CHIP_PEND
> > + &
> > SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_MASK) {
> > + ret = -EIO;
> > + dev_err(port->dev,
> > + "%s: chip error(%i)",
> > + __func__,
> > + intStatus.CHIP_PEND);
> > + break;
> > + }
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static int si4455_re_configure(struct uart_port *port)
> > +{
> > + int ret = 0;
> > + struct si4455_port *s = dev_get_drvdata(port->dev);
> > +
> > + mutex_lock(&s->mutex);
> > + s->configured = 0;
> > + if (s->power_count > 0)
> > + si4455_s_power(port->dev, 0);
> > +
> > + si4455_s_power(port->dev, 1);
> > + if (s->configuration.length > 0) {
> > + ret = si4455_configure(port, s->configuration.data);
> > + if (ret == 0)
> > + s->configured = 1;
> > +
> > + }
> > + mutex_unlock(&s->mutex);
> > + return ret;
> > +}
> > +
> > +static int si4455_do_work(struct uart_port *port)
> > +{
> > + int ret = 0;
> > + struct si4455_port *s = dev_get_drvdata(port->dev);
> > + struct circ_buf *xmit = &port->state->xmit;
> > + unsigned int tx_pending = 0;
> > + unsigned int tx_to_end = 0;
> > + u8 *data = NULL;
> > +
> > + mutex_lock(&s->mutex);
> > + if (s->configured && (s->power_count > 0)) {
> > + if (!(uart_circ_empty(xmit)
> > + || uart_tx_stopped(port)
> > + || s->tx_pending)) {
> > + tx_pending = uart_circ_chars_pending(xmit);
> > + if (s->package_size > 0) {
> > + if (tx_pending >= s->package_size) {
> > + tx_pending = s->package_size;
> > + data = devm_kzalloc(port->dev,
> > + s->package_size,
> > + GFP_KERNEL);
> > + tx_to_end =
> > CIRC_CNT_TO_END(xmit->head,
> > + xmit->tail,
> > +
> > UART_XMIT_SIZE);
> > + if (tx_to_end < tx_pending) {
> > + memcpy(data,
> > + xmit->buf +
> > xmit->tail,
> > + tx_to_end);
> > + memcpy(data,
> > + xmit->buf,
> > + tx_pending -
> > tx_to_end);
> > + } else {
> > + memcpy(data,
> > + xmit->buf +
> > xmit->tail,
> > + tx_pending);
> > + }
> > + if (si4455_begin_tx(port,
> > + s->tx_channel,
> > + tx_pending,
> > + data) == 0) {
> > + s->tx_pending = true;
> > + }
> > + devm_kfree(port->dev, data);
> > + }
> > + } else {
> > + //TODO: variable packet length
> > + }
> > + }
> > + if (!s->tx_pending) {
> > + if (s->package_size > 0) {
> > + ret = si4455_begin_rx(port,
> > + s->rx_channel,
> > + s->package_size);
> > + } else {
> > + //TODO: variable packet length
> > + }
> > + }
> > + }
> > + mutex_unlock(&s->mutex);
> > + return ret;
> > +}
> > +
> > +static void si4455_handle_rx_pend(struct si4455_port *s)
> > +{
> > + struct uart_port *port = &s->one.port;
> > + u8 *data = NULL;
> > + int sret = 0;
> > + int i = 0;
> > +
> > + if (s->package_size > 0) {
> > + data = devm_kzalloc(port->dev,
> > + s->package_size,
> > + GFP_KERNEL);
> > + sret = si4455_end_rx(port,
> > + s->package_size,
> > + data);
> > + if (sret == 0) {
> > + for (i = 0; i < s->package_size; i++) {
> > + uart_insert_char(port,
> > + 0,
> > + 0,
> > + data[i],
> > + TTY_NORMAL);
> > + port->icount.rx++;
> > + }
> > + tty_flip_buffer_push(&port->state->port);
> > + } else {
> > + dev_err(port->dev,
> > + "%s: si4455_end_rx error(%i)",
> > + __func__,
> > + sret);
> > + }
> > + devm_kfree(port->dev, data);
> > + } else {
> > + //TODO: variable packet length
> > + }
> > +}
> > +
> > +static void si4455_handle_tx_pend(struct si4455_port *s)
> > +{
> > + struct uart_port *port = &s->one.port;
> > + struct circ_buf *xmit = &port->state->xmit;
> > +
> > + if (s->tx_pending) {
> > + if (s->package_size) {
> > + port->icount.tx += s->package_size;
> > + xmit->tail = (xmit->tail + s->package_size)
> > + & (UART_XMIT_SIZE - 1);
> > + } else {
> > + //TODO: variable packet length
> > + }
> > + si4455_end_tx(port);
> > + s->tx_pending = 0;
> > + }
> > +}
> > +
> > +static irqreturn_t si4455_port_irq(struct si4455_port *s)
> > +{
> > + struct uart_port *port = &s->one.port;
> > + irqreturn_t ret = IRQ_NONE;
> > + struct si4455_int_status intStatus = { 0 };
> > + struct si4455_fifo_info fifoInfo = { 0 };
> > +
> > + mutex_lock(&s->mutex);
> > + if (s->configured && (s->power_count > 0)) {
> > + if (!si4455_get_int_status(port, 0, 0, 0, &intStatus)) {
> > + si4455_get_modem_status(port, 0, &s->modem_status);
> > + if (intStatus.CHIP_PEND
> > + & SI4455_CMD_GET_CHIP_STATUS_REP_CMD_ERROR_PEND_BIT)
> > {
> > + dev_err(port->dev,
> > + "%s: CHIP_STATUS:CMD_ERROR_PEND",
> > + __func__);
> > + } else if (intStatus.PH_PEND
> > + &
> > SI4455_CMD_GET_INT_STATUS_REP_PACKET_SENT_PEND_BIT) {
> > + dev_dbg(port->dev,
> > + "%s: PH_STATUS:PACKET_SENT_PEND",
> > + __func__);
> > + si4455_handle_tx_pend(s);
> > + } else if (intStatus.PH_PEND
> > + & SI4455_CMD_GET_INT_STATUS_REP_PACKET_RX_PEND_BIT)
> > {
> > + dev_dbg(port->dev,
> > + "%s: PH_STATUS:PACKET_RX_PEND",
> > + __func__);
> > + s->current_rssi = s->modem_status.CURR_RSSI;
> > + si4455_fifo_info(port, 0, &fifoInfo);
> > + si4455_handle_rx_pend(s);
> > + } else if (intStatus.PH_PEND
> > + & SI4455_CMD_GET_INT_STATUS_REP_CRC_ERROR_BIT) {
> > + dev_dbg(port->dev,
> > + "%s: PH_STATUS:CRC_ERROR_PEND",
> > + __func__);
> > + }
> > + ret = IRQ_HANDLED;
> > + }
> > + } else {
> > + ret = IRQ_HANDLED;
> > + }
> > + mutex_unlock(&s->mutex);
> > + si4455_do_work(port);
> > + return ret;
> > +}
> > +
> > +static irqreturn_t si4455_ist(int irq,
> > + void *dev_id)
> > +{
> > + struct si4455_port *s = (struct si4455_port *)dev_id;
> > + bool handled = false;
> > +
> > + if (si4455_port_irq(s) == IRQ_HANDLED)
> > + handled = true;
> > +
> > + return IRQ_RETVAL(handled);
> > +}
> > +
> > +static void si4455_tx_proc(struct work_struct *ws)
> > +{
> > + struct si4455_one *one = container_of(ws,
> > + struct si4455_one,
> > + tx_work);
> > +
> > + si4455_do_work(&one->port);
> > +}
> > +
> > +static unsigned int si4455_tx_empty(struct uart_port *port)
> > +{
> > + return TIOCSER_TEMT;
> > +}
> > +
> > +static unsigned int si4455_get_mctrl(struct uart_port *port)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > + return TIOCM_DSR | TIOCM_CAR;
> > +}
> > +
> > +static void si4455_set_mctrl(struct uart_port *port,
> > + unsigned int mctrl)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > +}
>
> Delete all these empty functions.
>
> > +
> > +static void si4455_break_ctl(struct uart_port *port,
> > + int break_state)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > +}
> > +
> > +static void si4455_set_termios(struct uart_port *port,
> > + struct ktermios *termios,
> > + struct ktermios *old)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > +}
> > +
> > +static int si4455_rs485_config(struct uart_port *port,
> > + struct serial_rs485 *rs485)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > +
> > + return 0;
> > +}
> > +
> > +static int si4455_startup(struct uart_port *port)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > + si4455_s_power(port->dev, 1);
> > + return 0;
> > +}
> > +
> > +static void si4455_shutdown(struct uart_port *port)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
> > + si4455_s_power(port->dev, 0);
> > +}
> > +
> > +static const char *si4455_type(struct uart_port *port)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(port->dev);
> > +
> > + if (port->type == PORT_SI4455) {
>
> Reverse this test.
>
> > + if (s->part_info.ROMID == 3)
> > + return "SI4455-B1A";
> > + else if (s->part_info.ROMID == 6)
> > + return "SI4455-C2A";
> > +
> > + }
> > + return NULL;
> > +}
> > +
> > +static int si4455_request_port(struct uart_port *port)
> > +{
> > + /* Do nothing */
> > + dev_dbg(port->dev, "%s", __func__);
> > + return 0;
> > +}
> > +
> > +static void si4455_config_port(struct uart_port *port,
> > + int flags)
> > +{
> > + dev_dbg(port->dev, "%s", __func__);
>
> Delete all these debug statements which only print the name of the
> function. Use ftrace for this instead.
>
> > + if (flags & UART_CONFIG_TYPE)
> > + port->type = PORT_SI4455;
> > +}
> > +
> > +static int si4455_verify_port(struct uart_port *port,
> > + struct serial_struct *s)
> > +{
> > + if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SI4455))
> > + return -EINVAL;
> > +
> > + if (s->irq != port->irq)
> > + return -EINVAL;
> > +
> > + return 0;
> > +}
> > +
> > +static void si4455_start_tx(struct uart_port *port)
> > +{
> > + struct si4455_one *one = container_of(port,
> > + struct si4455_one,
> > + port);
> > +
> > + dev_dbg(port->dev, "%s", __func__);
> > +
> > + if (!work_pending(&one->tx_work))
> > + schedule_work(&one->tx_work);
> > +
> > +}
> > +
> > +static int si4455_ioctl(struct uart_port *port,
> > + unsigned int cmd,
> > + unsigned long arg)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(port->dev);
> > + int ret = 0;
> > +
> > + dev_dbg(port->dev, "%s(%u)", __func__, cmd);
> > + switch (cmd) {
> > + case SI4455_IOC_SEZC:
> > + memcpy(&s->configuration, (void *)arg, sizeof(s->configuration));
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_SEZC, length(%i)",
> > + __func__,
> > + cmd,
> > + s->configuration.length);
> > + ret = si4455_re_configure(port);
>
> This needs to indented another tab.
>
> switch (cmd) {
> case SI4455_IOC_SEZC:
> memcpy(&s->configuration, (void *)arg, sizeof(s->configuration));
>
> Eep!!!
>
> Don't use memcpy() here. Use copy_from_user().
>
> void __user *argp = arg;
>
> if (copy_from_user(&s->configuration, argp,
> sizeof(s->configuration)))
> return -EFAULT;
>
> > + break;
> > + case SI4455_IOC_CEZC:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_CEZC",
> > + __func__,
> > + cmd);
> > + memset(&s->configuration, 0x00, sizeof(s->configuration));
> > + ret = si4455_re_configure(port);
> > + break;
> > + case SI4455_IOC_SEZP:
> > + memcpy(&s->patch, (void *)arg, sizeof(s->patch));
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_SEZP, length(%i)",
> > + __func__,
> > + cmd,
> > + s->configuration.length);
> > + break;
> > + case SI4455_IOC_CEZP:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_CEZP",
> > + __func__,
> > + cmd);
> > + memset(&s->patch, 0x00, sizeof(s->patch));
> > + break;
> > + case SI4455_IOC_STXC:
> > + s->tx_channel = *((u32 *)arg);
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_STXC, tx_channel(%i)",
> > + __func__,
> > + cmd,
> > + s->tx_channel);
> > + break;
> > + case SI4455_IOC_GTXC:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_GTXC",
> > + __func__,
> > + cmd);
> > + *((u32 *)arg) = s->tx_channel;
> > + break;
> > + case SI4455_IOC_SRXC:
> > + s->rx_channel = *((u32 *)arg);
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_SRXC, rx_channel(%i)",
> > + __func__,
> > + cmd,
> > + s->rx_channel);
> > + break;
> > + case SI4455_IOC_GRXC:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_GRXC",
> > + __func__,
> > + cmd);
> > + *((u32 *)arg) = s->rx_channel;
> > + break;
> > + case SI4455_IOC_SSIZ:
> > + s->package_size = *((u32 *)arg);
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_SSIZ, package_size(%i)",
> > + __func__,
> > + cmd,
> > + s->package_size);
> > + break;
> > + case SI4455_IOC_GSIZ:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_GSIZ",
> > + __func__,
> > + cmd);
> > + *((u32 *)arg) = s->package_size;
> > + break;
> > + case SI4455_IOC_GRSSI:
> > + dev_dbg(port->dev,
> > + "%s(%u): SI4455_IOC_GRSSI",
> > + __func__,
> > + cmd);
> > + *((u32 *)arg) = s->current_rssi;
> > + break;
> > + default:
> > + ret = -ENOIOCTLCMD;
> > + break;
> > + }
> > +
> > + if (ret == 0)
> > + si4455_do_work(port);
> > +
> > + return ret;
> > +}
> > +
> > +
> > +static void si4455_null_void(struct uart_port *port)
> > +{
> > + /* Do nothing */
> > +}
> > +
> > +static const struct uart_ops si4455_ops = {
> > + .tx_empty = si4455_tx_empty,
> > + .set_mctrl = si4455_set_mctrl,
> > + .get_mctrl = si4455_get_mctrl,
> > + .stop_tx = si4455_null_void,
> > + .start_tx = si4455_start_tx,
> > + .stop_rx = si4455_null_void,
> > + .break_ctl = si4455_break_ctl,
> > + .startup = si4455_startup,
> > + .shutdown = si4455_shutdown,
> > + .set_termios = si4455_set_termios,
> > + .type = si4455_type,
> > + .request_port = si4455_request_port,
> > + .release_port = si4455_null_void,
> > + .config_port = si4455_config_port,
> > + .verify_port = si4455_verify_port,
> > + .ioctl = si4455_ioctl,
> > +};
> > +
> > +static int __maybe_unused si4455_suspend(struct device *dev)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(dev);
> > +
> > + uart_suspend_port(&si4455_uart, &s->one.port);
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused si4455_resume(struct device *dev)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(dev);
> > +
> > + uart_resume_port(&si4455_uart, &s->one.port);
> > +
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(si4455_pm_ops, si4455_suspend, si4455_resume);
> > +
> > +static int si4455_probe(struct device *dev,
> > + int irq)
> > +{
> > + int ret;
> > + struct si4455_port *s;
> > +
> > + /* Alloc port structure */
> > + dev_dbg(dev, "%s\n", __func__);
> > + s = devm_kzalloc(dev, sizeof(*s), GFP_KERNEL);
> > + if (!s) {
> > + dev_err(dev, "Error allocating port structure\n");
> > + return -ENOMEM;
> > + }
> > +
> > + dev_set_drvdata(dev, s);
> > + mutex_init(&s->mutex);
> > +
> > + s->shdn_gpio = devm_gpiod_get(dev, "shdn", GPIOD_OUT_HIGH);
> > + if (IS_ERR(s->shdn_gpio)) {
> > + dev_err(dev, "Unable to reguest shdn gpio\n");
> > + ret = -EINVAL;
>
> Preserve the error code:
>
> ret = PTR_ERR(s->shdn_gpio);
>
> > + goto out_generic;
> > + }
> > +
> > + /* Initialize port data */
> > + s->one.port.dev = dev;
> > + s->one.port.line = 0;
> > + s->one.port.irq = irq;
> > + s->one.port.type = PORT_SI4455;
> > + s->one.port.fifosize = SI4455_FIFO_SIZE;
> > + s->one.port.flags = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
> > + s->one.port.iotype = UPIO_PORT;
> > + s->one.port.iobase = 0x00;
> > + s->one.port.membase = (void __iomem *)~0;
> > + s->one.port.rs485_config = si4455_rs485_config;
> > + s->one.port.ops = &si4455_ops;
> > +
> > + si4455_s_power(dev, 1);
> > +
> > + //detect
> > + ret = si4455_get_part_info(&s->one.port, &s->part_info);
> > + dev_dbg(dev, "si4455_get_part_info()==%i", ret);
> > + if (ret == 0) {
> > + dev_dbg(dev, "partInfo.CHIPREV= %u", s->part_info.CHIPREV);
> > + dev_dbg(dev, "partInfo.PART= %u", s->part_info.PART);
> > + dev_dbg(dev, "partInfo.PBUILD= %u", s->part_info.PBUILD);
> > + dev_dbg(dev, "partInfo.ID= %u", s->part_info.ID);
> > + dev_dbg(dev, "partInfo.CUSTOMER= %u",
> > s->part_info.CUSTOMER);
> > + dev_dbg(dev, "partInfo.ROMID= %u", s->part_info.ROMID);
> > + dev_dbg(dev, "partInfo.BOND= %u", s->part_info.BOND);
> > + if (s->part_info.PART != 0x5544) {
> > + dev_err(dev, "PART(%u) error", s->part_info.PART);
> > + ret = -ENODEV;
> > + }
> > + }
> > + si4455_s_power(dev, 0);
> > + if (ret)
> > + goto out_generic;
> > +
> > + /* Initialize queue for start TX */
> > + INIT_WORK(&s->one.tx_work, si4455_tx_proc);
> > +
> > + /* Register port */
> > + ret = uart_add_one_port(&si4455_uart, &s->one.port);
> > + if (ret) {
> > + s->one.port.dev = NULL;
> > + goto out_uart;
> > + }
> > +
> > + /* Setup interrupt */
> > + ret = devm_request_threaded_irq(dev,
> > + irq,
> > + NULL,
> > + si4455_ist,
> > + IRQF_ONESHOT | IRQF_SHARED,
> > + dev_name(dev),
> > + s);
> > + if (!ret)
> > + return 0;
>
> This is "Last if condition is reversed" anti-pattern. Always do error
> handling, never success handling.
>
> > +
> > + dev_err(dev, "Unable to reguest IRQ %i\n", irq);
> > +
> > +out_uart:
> > + uart_remove_one_port(&si4455_uart, &s->one.port);
> > +out_generic:
> > + mutex_destroy(&s->mutex);
> > +
> > + return ret;
> > +}
> > +
> > +static int si4455_remove(struct device *dev)
> > +{
> > + struct si4455_port *s = dev_get_drvdata(dev);
> > +
> > + cancel_work_sync(&s->one.tx_work);
> > + uart_remove_one_port(&si4455_uart, &s->one.port);
> > +
> > + mutex_destroy(&s->mutex);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id __maybe_unused si4455_dt_ids[] = {
> > + { .compatible = "silabs,si4455" },
> > + { .compatible = "silabs,si4455b1a" },
> > + { .compatible = "silabs,si4455c2a" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, si4455_dt_ids);
> > +
> > +static int si4455_spi_probe(struct spi_device *spi)
> > +{
> > + int ret;
> > +
> > + /* Setup SPI bus */
> > + spi->bits_per_word = 8;
> > + spi->mode = SPI_MODE_0;
> > + spi->max_speed_hz = 100000;
>
> This white space is whacky.
>
>
> > + ret = spi_setup(spi);
> > + if (ret)
> > + return ret;
> > +
> > + if (spi->dev.of_node) {
> > + const struct of_device_id *of_id
> > + = of_match_device(si4455_dt_ids, &spi->dev);
> > + if (!of_id)
> > + return -ENODEV;
> > +
> > + }
> > +
> > + return si4455_probe(&spi->dev, spi->irq);
> > +}
>
> Anyway, hopefully that's some ideas.
>
> regards,
> dan carpenter
>
>
Thank you for your suggestions. I made the canges suggested by you.
I'll test the driver in my development environment, then I'll come back with a new patch soon.
I set up a mail client on my linux dev environment, I hope my mails/patches/codes will be in proper quality in the future.
Üdvözlettel / Best regards:
József Horváth
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
