Hi Mauro > Before posting the big patch series again, let me send the new > version folded into a single patch. > > If you'd like to see the entire thing, I'm placing it here: > > https://gitlab.freedesktop.org/mchehab_kernel/hikey-970/-/commits/hikey970_v2/ Review 3/3 For next submission then to ease review it would be nice that the patch is spilt up a little. Maybe something like: - HW specific stuff in two patches (header fiels with register + setup code) - Display driver files - DSI driver files - build stuff (Makefile, Kconfig fragments) So all splits on file level - which should be easy to do. This will make it easier for more people to give feedback. It is a bit much to walk through 4k loc or what the full size is. And then we can also provide a-b or r-b for fragments so the reviewed parts can be ignored for later reviews. For the DSI parts I may be hit by the old "when you have a hammer then everything looks like a nail syndrome". In my case the hammer is the bridge interface. Suggestions: - Move encoder to display driver - Move connector creation to display driver (using drm_bridge_connector_init()) - Use drm_bridge interface for the DSI driver parts - Maybe use the HDMI bridge driver as a chained driver - I did not look to close on this - Use the standard bridge interface to find the bridge and drop use of the component framework I hope that some other drm people chime in here. Either to tell this is non-sense or confirm this is the way to go. The above does not give any hint how to use the gpio_mux to shift between the panel and HDMI. This logic needs to be in the display driver as the bridge driver will only be used for HDMI - as I understand the code. And I do not know how to do it. Some details in the following that are not related to the above. Sam > diff --git a/drivers/staging/hikey9xx/gpu/kirin9xx_dw_drm_dsi.c b/drivers/staging/hikey9xx/gpu/kirin9xx_dw_drm_dsi.c > new file mode 100644 > index 000000000000..a2eed961b7d5 > --- /dev/null > +++ b/drivers/staging/hikey9xx/gpu/kirin9xx_dw_drm_dsi.c > @@ -0,0 +1,2126 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * DesignWare MIPI DSI Host Controller v1.02 driver > + * > + * Copyright (c) 2016 Linaro Limited. > + * Copyright (c) 2014-2016 Hisilicon Limited. > + * Copyright (c) 2014-2020, Huawei Technologies Co., Ltd > + * > + * Author: > + * <shizongxuan@xxxxxxxxxx> > + * <zhangxiubin@xxxxxxxxxx> > + */ > + > +#include <linux/clk.h> > +#include <linux/component.h> > +#include <linux/of_device.h> > +#include <linux/of_graph.h> > +#include <linux/iopoll.h> > +#include <video/mipi_display.h> > +#include <linux/gpio/consumer.h> > +#include <linux/of_address.h> Sort > + > +#include <drm/drm_of.h> > +#include <drm/drm_crtc_helper.h> > +#include <drm/drm_mipi_dsi.h> > +#include <drm/drm_encoder.h> > +#include <drm/drm_device.h> > +#include <drm/drm_atomic_helper.h> > +#include <drm/drm_panel.h> > +#include <drm/drm_probe_helper.h> Sort > + > +#include "kirin9xx_dw_dsi_reg.h" > +#include "kirin9xx_dpe.h" > +#include "kirin9xx_drm_drv.h" > +#include "kirin9xx_drm_dpe_utils.h" Sort > + > +#define PHY_REF_CLK_RATE 19200000 > +#define PHY_REF_CLK_PERIOD_PS (1000000000 / (PHY_REF_CLK_RATE / 1000)) > + > +#define encoder_to_dsi(encoder) \ > + container_of(encoder, struct dw_dsi, encoder) > +#define host_to_dsi(host) \ > + container_of(host, struct dw_dsi, host) > +#define connector_to_dsi(connector) \ > + container_of(connector, struct dw_dsi, connector) Move the upcast next to the struct definition. > +#define DSS_REDUCE(x) ((x) > 0 ? ((x) - 1) : (x)) > + > +enum dsi_output_client { > + OUT_HDMI = 0, > + OUT_PANEL, > + OUT_MAX > +}; > + > +struct mipi_phy_params { I did not check all fiels but I managed to find at least one unused field. Cheack and delete what is unused. > + u64 lane_byte_clk; > + u32 clk_division; > + > + u32 clk_lane_lp2hs_time; > + u32 clk_lane_hs2lp_time; > + u32 data_lane_lp2hs_time; > + u32 data_lane_hs2lp_time; > + u32 clk2data_delay; > + u32 data2clk_delay; > + > + u32 clk_pre_delay; > + u32 clk_post_delay; > + u32 clk_t_lpx; > + u32 clk_t_hs_prepare; > + u32 clk_t_hs_zero; > + u32 clk_t_hs_trial; > + u32 clk_t_wakeup; > + u32 data_pre_delay; > + u32 data_post_delay; > + u32 data_t_lpx; > + u32 data_t_hs_prepare; > + u32 data_t_hs_zero; > + u32 data_t_hs_trial; > + u32 data_t_ta_go; > + u32 data_t_ta_get; > + u32 data_t_wakeup; > + > + u32 phy_stop_wait_time; > + > + u32 rg_vrefsel_vcm; > + u32 rg_hstx_ckg_sel; > + u32 rg_pll_fbd_div5f; > + u32 rg_pll_fbd_div1f; > + u32 rg_pll_fbd_2p; > + u32 rg_pll_enbwt; > + u32 rg_pll_fbd_p; > + u32 rg_pll_fbd_s; > + u32 rg_pll_pre_div1p; > + u32 rg_pll_pre_p; > + u32 rg_pll_vco_750m; > + u32 rg_pll_lpf_rs; > + u32 rg_pll_lpf_cs; > + u32 rg_pll_enswc; > + u32 rg_pll_chp; > + Some indent gone wrong here? > + u32 pll_register_override; /* 0x1E[0] */ > + u32 pll_power_down; /* 0x1E[1] */ > + u32 rg_band_sel; /* 0x1E[2] */ > + u32 rg_phase_gen_en; /* 0x1E[3] */ > + u32 reload_sel; /* 0x1E[4] */ > + u32 rg_pll_cp_p; /* 0x1E[7:5] */ > + u32 rg_pll_refsel; /* 0x16[1:0] */ > + u32 rg_pll_cp; /* 0x16[7:5] */ > + u32 load_command; > + > + /* for CDPHY */ > + u32 rg_cphy_div; /* Q */ > + u32 rg_div; /* M 0x4A[7:0] */ > + u32 rg_pre_div; /* N 0x49[0] */ > + u32 rg_320m; /* 0x48[2] */ > + u32 rg_2p5g; /* 0x48[1] */ > + u32 rg_0p8v; /* 0x48[0] */ > + u32 rg_lpf_r; /* 0x46[5:4] */ > + u32 rg_cp; /* 0x46[3:0] */ > + u32 t_prepare; > + u32 t_lpx; > + u32 t_prebegin; > + u32 t_post; > +}; > + > +struct dsi_hw_ctx { > + void __iomem *base; > + char __iomem *peri_crg_base; > + void __iomem *pctrl_base; > + > + u32 g_dss_version_tag; > + > + struct clk *dss_dphy0_ref_clk; > + struct clk *dss_dphy1_ref_clk; Not used, delete. > + struct clk *dss_dphy0_cfg_clk; > + struct clk *dss_dphy1_cfg_clk; Not used, delete. > + struct clk *dss_pclk_dsi0_clk; > + struct clk *dss_pclk_dsi1_clk; Not sued, delete. > +}; > + > +struct dw_dsi_client { > + u32 lanes; > + u32 phy_clock; /* in kHz */ > + enum mipi_dsi_pixel_format format; > + unsigned long mode_flags; > +}; > + > +struct mipi_panel_info { Some filed in the following are either not used or in some cases only read. Clean it up. Example: clk_t_hs_exit_adjust is assigned 0 and only read. Looks like stuff to drop. > + u8 dsi_version; > + u8 vc; > + u8 lane_nums; > + u8 lane_nums_select_support; > + u8 color_mode; > + u32 dsi_bit_clk; /* clock lane(p/n) */ > + u32 burst_mode; > + u32 max_tx_esc_clk; > + u8 non_continue_en; > + > + u32 dsi_bit_clk_val1; > + u32 dsi_bit_clk_val2; > + u32 dsi_bit_clk_val3; > + u32 dsi_bit_clk_val4; > + u32 dsi_bit_clk_val5; > + u32 dsi_bit_clk_upt; > + /* uint32_t dsi_pclk_rate; */ > + > + u32 hs_wr_to_time; > + > + /* dphy config parameter adjust */ > + u32 clk_post_adjust; > + u32 clk_pre_adjust; > + u32 clk_pre_delay_adjust; > + u32 clk_t_hs_exit_adjust; > + u32 clk_t_hs_trial_adjust; > + u32 clk_t_hs_prepare_adjust; > + int clk_t_lpx_adjust; > + u32 clk_t_hs_zero_adjust; > + u32 data_post_delay_adjust; > + int data_t_lpx_adjust; > + u32 data_t_hs_prepare_adjust; > + u32 data_t_hs_zero_adjust; > + u32 data_t_hs_trial_adjust; > + u32 rg_vrefsel_vcm_adjust; > + > + /* only for Chicago<3660> use */ > + u32 rg_vrefsel_vcm_clk_adjust; > + u32 rg_vrefsel_vcm_data_adjust; > + > + u32 phy_mode; /* 0: DPHY, 1:CPHY */ > + u32 lp11_flag; > +}; > + > +struct ldi_panel_info { Fileds are only partially used. > + u32 h_back_porch; > + u32 h_front_porch; > + u32 h_pulse_width; > + > + /* > + * note: vbp > 8 if used overlay compose, > + * also lcd vbp > 8 in lcd power on sequence > + */ > + u32 v_back_porch; > + u32 v_front_porch; > + u32 v_pulse_width; > + > + u8 hsync_plr; > + u8 vsync_plr; > + u8 pixelclk_plr; > + u8 data_en_plr; > + > + /* for cabc */ > + u8 dpi0_overlap_size; > + u8 dpi1_overlap_size; > +}; > + > +struct dw_dsi { > + struct drm_encoder encoder; > + struct drm_bridge *bridge; > + struct drm_panel *panel; > + struct mipi_dsi_host host; > + struct drm_connector connector; /* connector for panel */ > + struct drm_display_mode cur_mode; > + struct dsi_hw_ctx *ctx; Would it be possible to embed dsi_hw_ctx? So everything is allocated in one go. > + struct mipi_phy_params phy; > + struct mipi_panel_info mipi; > + struct ldi_panel_info ldi; > + u32 lanes; > + enum mipi_dsi_pixel_format format; > + unsigned long mode_flags; > + struct gpio_desc *gpio_mux; > + struct dw_dsi_client client[OUT_MAX]; > + enum dsi_output_client cur_client, attached_client; > + bool enable; > +}; > + > +struct dsi_data { > + struct dw_dsi dsi; > + struct dsi_hw_ctx ctx; > +}; If dsi_hw_ctx is embedded in dw_dsi then this struct can be dropped. > + > +struct dsi_phy_range { > + u32 min_range_kHz; > + u32 max_range_kHz; > + u32 pll_vco_750M; > + u32 hstx_ckg_sel; > +}; Not used, delete. > + > +static const struct dsi_phy_range dphy_range_info[] = { > + { 46875, 62500, 1, 7 }, > + { 62500, 93750, 0, 7 }, > + { 93750, 125000, 1, 6 }, > + { 125000, 187500, 0, 6 }, > + { 187500, 250000, 1, 5 }, > + { 250000, 375000, 0, 5 }, > + { 375000, 500000, 1, 4 }, > + { 500000, 750000, 0, 4 }, > + { 750000, 1000000, 1, 0 }, > + { 1000000, 1500000, 0, 0 } > +}; Not used, delete. > + > +/* > + * Except for debug, this is identical to the one defined at > + * kirin9xx_drm_dpe_utils.h. > + */ > + > +void dsi_set_output_client(struct drm_device *dev) > +{ > + struct drm_connector_list_iter conn_iter; > + struct drm_connector *connector; > + enum dsi_output_client client; > + struct drm_encoder *encoder; > + struct dw_dsi *dsi; > + > + mutex_lock(&dev->mode_config.mutex); > + > + /* find dsi encoder */ > + drm_for_each_encoder(encoder, dev) > + if (encoder->encoder_type == DRM_MODE_ENCODER_DSI) > + break; > + dsi = encoder_to_dsi(encoder); > + > + /* find HDMI connector */ > + drm_connector_list_iter_begin(dev, &conn_iter); > + drm_for_each_connector_iter(connector, &conn_iter) > + if (connector->connector_type == DRM_MODE_CONNECTOR_HDMIA) > + break; > + > + /* > + * set the proper dsi output client > + */ > + client = connector->status == connector_status_connected ? > + OUT_HDMI : OUT_PANEL; > + > + if (client != dsi->cur_client) { > + gpiod_set_value_cansleep(dsi->gpio_mux, client); > + dsi->cur_client = client; > + > + msleep(20); > + > + drm_info(dev, "client change to %s\n", > + client == OUT_HDMI ? "HDMI" : "panel"); > + } > + > + mutex_unlock(&dev->mode_config.mutex); > +} > +EXPORT_SYMBOL(dsi_set_output_client); > + > +static void kirin970_get_dsi_dphy_ctrl(struct dw_dsi *dsi, > + struct mipi_phy_params *phy_ctrl, u32 id) > +{ > + struct mipi_panel_info *mipi = NULL; > + struct drm_display_mode *mode = NULL; > + u32 dphy_req_kHz; > + int bpp; > + u32 ui = 0; > + u32 m_pll = 0; > + u32 n_pll = 0; > + u64 lane_clock = 0; > + u64 vco_div = 1; > + u32 m_n_fract = 0; > + u32 m_n_int = 0; > + > + u32 accuracy = 0; > + u32 unit_tx_byte_clk_hs = 0; > + u32 clk_post = 0; > + u32 clk_pre = 0; > + u32 clk_t_hs_exit = 0; > + u32 clk_pre_delay = 0; > + u32 clk_t_hs_prepare = 0; > + u32 clk_t_lpx = 0; > + u32 clk_t_hs_zero = 0; > + u32 clk_t_hs_trial = 0; > + u32 data_post_delay = 0; > + u32 data_t_hs_prepare = 0; > + u32 data_t_hs_zero = 0; > + u32 data_t_hs_trial = 0; > + u32 data_t_lpx = 0; > + > + WARN_ON(!phy_ctrl); > + WARN_ON(!dsi); > + > + mode = &dsi->cur_mode; > + mipi = &dsi->mipi; > + > + /* > + * count phy params > + */ > + bpp = mipi_dsi_pixel_format_to_bpp(dsi->client[id].format); > + if (bpp < 0) > + return; > + > + if (mode->clock > 80000) > + dsi->client[id].lanes = 4; > + else > + dsi->client[id].lanes = 3; > + > + if (dsi->client[id].phy_clock) > + dphy_req_kHz = dsi->client[id].phy_clock; > + else > + dphy_req_kHz = mode->clock * bpp / dsi->client[id].lanes; > + > + lane_clock = dphy_req_kHz / 1000; > + DRM_DEBUG("Expected : lane_clock = %llu M\n", lane_clock); > + > + /************************ PLL parameters config *********************/ > + /* chip spec : */ > + /* If the output data rate is below 320 Mbps, RG_BNAD_SEL should be set to 1. */ > + /* At this mode a post divider of 1/4 will be applied to VCO. */ > + if ((lane_clock >= 320) && (lane_clock <= 2500)) { > + phy_ctrl->rg_band_sel = 0; > + vco_div = 1; > + } else if ((lane_clock >= 80) && (lane_clock < 320)) { > + phy_ctrl->rg_band_sel = 1; > + vco_div = 4; > + } else { > + DRM_ERROR("80M <= lane_clock< = 2500M, not support lane_clock = %llu M.\n", > + lane_clock); > + } > + > + m_n_int = lane_clock * vco_div * 1000000UL / DEFAULT_MIPI_CLK_RATE; > + m_n_fract = ((lane_clock * vco_div * 1000000UL * 1000UL / DEFAULT_MIPI_CLK_RATE) % 1000) * 10 / 1000; > + > + n_pll = 2; > + > + m_pll = (u32)(lane_clock * vco_div * n_pll * 1000000UL / DEFAULT_MIPI_CLK_RATE); > + > + lane_clock = m_pll * (DEFAULT_MIPI_CLK_RATE / n_pll) / vco_div; > + if (lane_clock > 750000000) > + phy_ctrl->rg_cp = 3; > + else if ((lane_clock >= 80000000) && (lane_clock <= 750000000)) > + phy_ctrl->rg_cp = 1; > + else > + DRM_ERROR("80M <= lane_clock< = 2500M, not support lane_clock = %llu M.\n", > + lane_clock); > + > + /* chip spec : */ > + phy_ctrl->rg_pre_div = n_pll - 1; > + phy_ctrl->rg_div = m_pll; > + phy_ctrl->rg_0p8v = 0; > + phy_ctrl->rg_2p5g = 1; > + phy_ctrl->rg_320m = 0; > + phy_ctrl->rg_lpf_r = 0; > + > + /* TO DO HSTX select VCM VREF */ > + phy_ctrl->rg_vrefsel_vcm = 0x5d; > + > + /******************** clock/data lane parameters config ******************/ > + accuracy = 10; > + ui = (u32)(10 * 1000000000UL * accuracy / lane_clock); > + /* unit of measurement */ > + unit_tx_byte_clk_hs = 8 * ui; > + > + /* D-PHY Specification : 60ns + 52*UI <= clk_post */ > + clk_post = 600 * accuracy + 52 * ui + unit_tx_byte_clk_hs + mipi->clk_post_adjust * ui; > + > + /* D-PHY Specification : clk_pre >= 8*UI */ > + clk_pre = 8 * ui + unit_tx_byte_clk_hs + mipi->clk_pre_adjust * ui; > + > + /* D-PHY Specification : clk_t_hs_exit >= 100ns */ > + clk_t_hs_exit = 1000 * accuracy + 100 * accuracy + mipi->clk_t_hs_exit_adjust * ui; > + > + /* clocked by TXBYTECLKHS */ > + clk_pre_delay = 0 + mipi->clk_pre_delay_adjust * ui; > + > + /* D-PHY Specification : clk_t_hs_trial >= 60ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_hs_trial = 600 * accuracy + 3 * unit_tx_byte_clk_hs + mipi->clk_t_hs_trial_adjust * ui; > + > + /* D-PHY Specification : 38ns <= clk_t_hs_prepare <= 95ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_hs_prepare = 660 * accuracy; > + > + /* clocked by TXBYTECLKHS */ > + data_post_delay = 0 + mipi->data_post_delay_adjust * ui; > + > + /* D-PHY Specification : data_t_hs_trial >= max( n*8*UI, 60ns + n*4*UI ), n = 1 */ > + /* clocked by TXBYTECLKHS */ > + data_t_hs_trial = ((600 * accuracy + 4 * ui) >= (8 * ui) ? (600 * accuracy + 4 * ui) : (8 * ui)) + > + 2 * unit_tx_byte_clk_hs + mipi->data_t_hs_trial_adjust * ui; > + > + /* D-PHY Specification : 40ns + 4*UI <= data_t_hs_prepare <= 85ns + 6*UI */ > + /* clocked by TXBYTECLKHS */ > + data_t_hs_prepare = 400 * accuracy + 4 * ui; > + /* D-PHY chip spec : clk_t_lpx + clk_t_hs_prepare > 200ns */ > + /* D-PHY Specification : clk_t_lpx >= 50ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_lpx = (uint32_t)(2000 * accuracy + 10 * accuracy + mipi->clk_t_lpx_adjust * ui - clk_t_hs_prepare); > + > + /* D-PHY Specification : clk_t_hs_zero + clk_t_hs_prepare >= 300 ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_hs_zero = (uint32_t)(3000 * accuracy + 3 * unit_tx_byte_clk_hs + mipi->clk_t_hs_zero_adjust * ui - clk_t_hs_prepare); > + > + /* D-PHY chip spec : data_t_lpx + data_t_hs_prepare > 200ns */ > + /* D-PHY Specification : data_t_lpx >= 50ns */ > + /* clocked by TXBYTECLKHS */ > + data_t_lpx = (uint32_t)(2000 * accuracy + 10 * accuracy + mipi->data_t_lpx_adjust * ui - data_t_hs_prepare); > + > + /* D-PHY Specification : data_t_hs_zero + data_t_hs_prepare >= 145ns + 10*UI */ > + /* clocked by TXBYTECLKHS */ > + data_t_hs_zero = (uint32_t)(1450 * accuracy + 10 * ui + > + 3 * unit_tx_byte_clk_hs + mipi->data_t_hs_zero_adjust * ui - data_t_hs_prepare); > + > + phy_ctrl->clk_pre_delay = DIV_ROUND_UP(clk_pre_delay, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_prepare = DIV_ROUND_UP(clk_t_hs_prepare, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_lpx = DIV_ROUND_UP(clk_t_lpx, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_zero = DIV_ROUND_UP(clk_t_hs_zero, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_trial = DIV_ROUND_UP(clk_t_hs_trial, unit_tx_byte_clk_hs); > + > + phy_ctrl->data_post_delay = DIV_ROUND_UP(data_post_delay, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_prepare = DIV_ROUND_UP(data_t_hs_prepare, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_lpx = DIV_ROUND_UP(data_t_lpx, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_zero = DIV_ROUND_UP(data_t_hs_zero, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_trial = DIV_ROUND_UP(data_t_hs_trial, unit_tx_byte_clk_hs); > + > + phy_ctrl->clk_post_delay = phy_ctrl->data_t_hs_trial + DIV_ROUND_UP(clk_post, unit_tx_byte_clk_hs); > + phy_ctrl->data_pre_delay = phy_ctrl->clk_pre_delay + 2 + phy_ctrl->clk_t_lpx + > + phy_ctrl->clk_t_hs_prepare + phy_ctrl->clk_t_hs_zero + 8 + DIV_ROUND_UP(clk_pre, unit_tx_byte_clk_hs); > + > + phy_ctrl->clk_lane_lp2hs_time = phy_ctrl->clk_pre_delay + phy_ctrl->clk_t_lpx + phy_ctrl->clk_t_hs_prepare + > + phy_ctrl->clk_t_hs_zero + 5 + 7; > + phy_ctrl->clk_lane_hs2lp_time = phy_ctrl->clk_t_hs_trial + phy_ctrl->clk_post_delay + 8 + 4; > + phy_ctrl->data_lane_lp2hs_time = phy_ctrl->data_pre_delay + phy_ctrl->data_t_lpx + phy_ctrl->data_t_hs_prepare + > + phy_ctrl->data_t_hs_zero + 5 + 7; > + phy_ctrl->data_lane_hs2lp_time = phy_ctrl->data_t_hs_trial + 8 + 5; > + > + phy_ctrl->phy_stop_wait_time = phy_ctrl->clk_post_delay + 4 + phy_ctrl->clk_t_hs_trial + > + DIV_ROUND_UP(clk_t_hs_exit, unit_tx_byte_clk_hs) - (phy_ctrl->data_post_delay + 4 + phy_ctrl->data_t_hs_trial) + 3; > + > + phy_ctrl->lane_byte_clk = lane_clock / 8; > + phy_ctrl->clk_division = (((phy_ctrl->lane_byte_clk / 2) % mipi->max_tx_esc_clk) > 0) ? > + (uint32_t)(phy_ctrl->lane_byte_clk / 2 / mipi->max_tx_esc_clk + 1) : > + (uint32_t)(phy_ctrl->lane_byte_clk / 2 / mipi->max_tx_esc_clk); > + > + DRM_DEBUG("DPHY clock_lane and data_lane config :\n" > + "lane_clock = %llu, n_pll=%d, m_pll=%d\n" > + "rg_cp=%d\n" > + "rg_band_sel=%d\n" > + "rg_vrefsel_vcm=%d\n" > + "clk_pre_delay=%d\n" > + "clk_post_delay=%d\n" > + "clk_t_hs_prepare=%d\n" > + "clk_t_lpx=%d\n" > + "clk_t_hs_zero=%d\n" > + "clk_t_hs_trial=%d\n" > + "data_pre_delay=%d\n" > + "data_post_delay=%d\n" > + "data_t_hs_prepare=%d\n" > + "data_t_lpx=%d\n" > + "data_t_hs_zero=%d\n" > + "data_t_hs_trial=%d\n" > + "clk_lane_lp2hs_time=%d\n" > + "clk_lane_hs2lp_time=%d\n" > + "data_lane_lp2hs_time=%d\n" > + "data_lane_hs2lp_time=%d\n" > + "phy_stop_wait_time=%d\n", > + lane_clock, n_pll, m_pll, > + phy_ctrl->rg_cp, > + phy_ctrl->rg_band_sel, > + phy_ctrl->rg_vrefsel_vcm, > + phy_ctrl->clk_pre_delay, > + phy_ctrl->clk_post_delay, > + phy_ctrl->clk_t_hs_prepare, > + phy_ctrl->clk_t_lpx, > + phy_ctrl->clk_t_hs_zero, > + phy_ctrl->clk_t_hs_trial, > + phy_ctrl->data_pre_delay, > + phy_ctrl->data_post_delay, > + phy_ctrl->data_t_hs_prepare, > + phy_ctrl->data_t_lpx, > + phy_ctrl->data_t_hs_zero, > + phy_ctrl->data_t_hs_trial, > + phy_ctrl->clk_lane_lp2hs_time, > + phy_ctrl->clk_lane_hs2lp_time, > + phy_ctrl->data_lane_lp2hs_time, > + phy_ctrl->data_lane_hs2lp_time, > + phy_ctrl->phy_stop_wait_time); > +} > + > +static void kirin960_get_dsi_phy_ctrl(struct dw_dsi *dsi, > + struct mipi_phy_params *phy_ctrl, u32 id) > +{ > + struct mipi_panel_info *mipi = NULL; > + struct drm_display_mode *mode = NULL; > + u32 dphy_req_kHz; > + int bpp; > + u32 ui = 0; > + u32 m_pll = 0; > + u32 n_pll = 0; > + u32 m_n_fract = 0; > + u32 m_n_int = 0; > + u64 lane_clock = 0; > + u64 vco_div = 1; > + > + u32 accuracy = 0; > + u32 unit_tx_byte_clk_hs = 0; > + u32 clk_post = 0; > + u32 clk_pre = 0; > + u32 clk_t_hs_exit = 0; > + u32 clk_pre_delay = 0; > + u32 clk_t_hs_prepare = 0; > + u32 clk_t_lpx = 0; > + u32 clk_t_hs_zero = 0; > + u32 clk_t_hs_trial = 0; > + u32 data_post_delay = 0; > + u32 data_t_hs_prepare = 0; > + u32 data_t_hs_zero = 0; > + u32 data_t_hs_trial = 0; > + u32 data_t_lpx = 0; > + u32 clk_pre_delay_reality = 0; > + u32 clk_t_hs_zero_reality = 0; > + u32 clk_post_delay_reality = 0; > + u32 data_t_hs_zero_reality = 0; > + u32 data_post_delay_reality = 0; > + u32 data_pre_delay_reality = 0; > + > + WARN_ON(!phy_ctrl); > + WARN_ON(!dsi); > + > + mode = &dsi->cur_mode; > + mipi = &dsi->mipi; > + > + /* > + * count phy params > + */ > + bpp = mipi_dsi_pixel_format_to_bpp(dsi->client[id].format); > + if (bpp < 0) > + return; > + > + if (mode->clock > 80000) > + dsi->client[id].lanes = 4; > + else > + dsi->client[id].lanes = 3; > + > + if (dsi->client[id].phy_clock) > + dphy_req_kHz = dsi->client[id].phy_clock; > + else > + dphy_req_kHz = mode->clock * bpp / dsi->client[id].lanes; > + > + lane_clock = dphy_req_kHz / 1000; > + DRM_INFO("Expected : lane_clock = %llu M\n", lane_clock); > + > + /************************ PLL parameters config *********************/ > + > + /* > + * chip spec : > + * If the output data rate is below 320 Mbps, > + * RG_BNAD_SEL should be set to 1. > + * At this mode a post divider of 1/4 will be applied to VCO. > + */ > + if ((lane_clock >= 320) && (lane_clock <= 2500)) { > + phy_ctrl->rg_band_sel = 0; /* 0x1E[2] */ > + vco_div = 1; > + } else if ((lane_clock >= 80) && (lane_clock < 320)) { > + phy_ctrl->rg_band_sel = 1; > + vco_div = 4; > + } else { > + DRM_ERROR("80M <= lane_clock< = 2500M, not support lane_clock = %llu M\n", > + lane_clock); > + } > + > + m_n_int = lane_clock * vco_div * 1000000UL / DEFAULT_MIPI_CLK_RATE; > + m_n_fract = ((lane_clock * vco_div * 1000000UL * 1000UL / DEFAULT_MIPI_CLK_RATE) % 1000) * 10 / 1000; > + > + if (m_n_int % 2 == 0) { > + if (m_n_fract * 6 >= 50) { > + n_pll = 2; > + m_pll = (m_n_int + 1) * n_pll; > + } else if (m_n_fract * 6 >= 30) { > + n_pll = 3; > + m_pll = m_n_int * n_pll + 2; > + } else { > + n_pll = 1; > + m_pll = m_n_int * n_pll; > + } > + } else { > + if (m_n_fract * 6 >= 50) { > + n_pll = 1; > + m_pll = (m_n_int + 1) * n_pll; > + } else if (m_n_fract * 6 >= 30) { > + n_pll = 1; > + m_pll = (m_n_int + 1) * n_pll; > + } else if (m_n_fract * 6 >= 10) { > + n_pll = 3; > + m_pll = m_n_int * n_pll + 1; > + } else { > + n_pll = 2; > + m_pll = m_n_int * n_pll; > + } > + } > + > + /* if set rg_pll_enswc=1, rg_pll_fbd_s can't be 0 */ > + if (m_pll <= 8) { > + phy_ctrl->rg_pll_fbd_s = 1; > + phy_ctrl->rg_pll_enswc = 0; > + > + if (m_pll % 2 == 0) { > + phy_ctrl->rg_pll_fbd_p = m_pll / 2; > + } else { > + if (n_pll == 1) { > + n_pll *= 2; > + phy_ctrl->rg_pll_fbd_p = (m_pll * 2) / 2; > + } else { > + DRM_ERROR("phy m_pll not support!m_pll = %d\n", m_pll); > + return; > + } > + } > + } else if (m_pll <= 300) { > + if (m_pll % 2 == 0) > + phy_ctrl->rg_pll_enswc = 0; > + else > + phy_ctrl->rg_pll_enswc = 1; > + > + phy_ctrl->rg_pll_fbd_s = 1; > + phy_ctrl->rg_pll_fbd_p = m_pll / 2; > + } else if (m_pll <= 315) { > + phy_ctrl->rg_pll_fbd_p = 150; > + phy_ctrl->rg_pll_fbd_s = m_pll - 2 * phy_ctrl->rg_pll_fbd_p; > + phy_ctrl->rg_pll_enswc = 1; > + } else { > + DRM_ERROR("phy m_pll not support!m_pll = %d\n", m_pll); > + return; > + } > + > + phy_ctrl->rg_pll_pre_p = n_pll; > + > + lane_clock = m_pll * (DEFAULT_MIPI_CLK_RATE / n_pll) / vco_div; > + DRM_INFO("Config : lane_clock = %llu\n", lane_clock); > + > + /* FIXME : */ > + phy_ctrl->rg_pll_cp = 1; /* 0x16[7:5] */ > + phy_ctrl->rg_pll_cp_p = 3; /* 0x1E[7:5] */ > + > + /* test_code_0x14 other parameters config */ > + phy_ctrl->rg_pll_enbwt = 0; /* 0x14[2] */ > + phy_ctrl->rg_pll_chp = 0; /* 0x14[1:0] */ > + > + /* test_code_0x16 other parameters config, 0x16[3:2] reserved */ > + phy_ctrl->rg_pll_lpf_cs = 0; /* 0x16[4] */ > + phy_ctrl->rg_pll_refsel = 1; /* 0x16[1:0] */ > + > + /* test_code_0x1E other parameters config */ > + phy_ctrl->reload_sel = 1; /* 0x1E[4] */ > + phy_ctrl->rg_phase_gen_en = 1; /* 0x1E[3] */ > + phy_ctrl->pll_power_down = 0; /* 0x1E[1] */ > + phy_ctrl->pll_register_override = 1; /* 0x1E[0] */ > + > + /* HSTX select VCM VREF */ > + phy_ctrl->rg_vrefsel_vcm = 0x55; > + if (mipi->rg_vrefsel_vcm_clk_adjust != 0) > + phy_ctrl->rg_vrefsel_vcm = (phy_ctrl->rg_vrefsel_vcm & 0x0F) | > + ((mipi->rg_vrefsel_vcm_clk_adjust & 0x0F) << 4); > + > + if (mipi->rg_vrefsel_vcm_data_adjust != 0) > + phy_ctrl->rg_vrefsel_vcm = (phy_ctrl->rg_vrefsel_vcm & 0xF0) | > + (mipi->rg_vrefsel_vcm_data_adjust & 0x0F); > + > + /* if reload_sel = 1, need to set load_command */ > + phy_ctrl->load_command = 0x5A; > + > + /******************** clock/data lane parameters config ******************/ > + accuracy = 10; > + ui = 10 * 1000000000UL * accuracy / lane_clock; > + /* unit of measurement */ > + unit_tx_byte_clk_hs = 8 * ui; > + > + /* D-PHY Specification : 60ns + 52*UI <= clk_post */ > + clk_post = 600 * accuracy + 52 * ui + mipi->clk_post_adjust * ui; > + > + /* D-PHY Specification : clk_pre >= 8*UI */ > + clk_pre = 8 * ui + mipi->clk_pre_adjust * ui; > + > + /* D-PHY Specification : clk_t_hs_exit >= 100ns */ > + clk_t_hs_exit = 1000 * accuracy + mipi->clk_t_hs_exit_adjust * ui; > + > + /* clocked by TXBYTECLKHS */ > + clk_pre_delay = 0 + mipi->clk_pre_delay_adjust * ui; > + > + /* D-PHY Specification : clk_t_hs_trial >= 60ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_hs_trial = 600 * accuracy + 3 * unit_tx_byte_clk_hs + mipi->clk_t_hs_trial_adjust * ui; > + > + /* D-PHY Specification : 38ns <= clk_t_hs_prepare <= 95ns */ > + /* clocked by TXBYTECLKHS */ > + if (mipi->clk_t_hs_prepare_adjust == 0) > + mipi->clk_t_hs_prepare_adjust = 43; > + > + clk_t_hs_prepare = ((380 * accuracy + mipi->clk_t_hs_prepare_adjust * ui) <= (950 * accuracy - 8 * ui)) ? > + (380 * accuracy + mipi->clk_t_hs_prepare_adjust * ui) : (950 * accuracy - 8 * ui); > + > + /* clocked by TXBYTECLKHS */ > + data_post_delay = 0 + mipi->data_post_delay_adjust * ui; > + > + /* D-PHY Specification : data_t_hs_trial >= max( n*8*UI, 60ns + n*4*UI ), n = 1 */ > + /* clocked by TXBYTECLKHS */ > + data_t_hs_trial = ((600 * accuracy + 4 * ui) >= (8 * ui) ? (600 * accuracy + 4 * ui) : (8 * ui)) + 8 * ui + > + 3 * unit_tx_byte_clk_hs + mipi->data_t_hs_trial_adjust * ui; > + > + /* D-PHY Specification : 40ns + 4*UI <= data_t_hs_prepare <= 85ns + 6*UI */ > + /* clocked by TXBYTECLKHS */ > + if (mipi->data_t_hs_prepare_adjust == 0) > + mipi->data_t_hs_prepare_adjust = 35; > + > + data_t_hs_prepare = ((400 * accuracy + 4 * ui + mipi->data_t_hs_prepare_adjust * ui) <= (850 * accuracy + 6 * ui - 8 * ui)) ? > + (400 * accuracy + 4 * ui + mipi->data_t_hs_prepare_adjust * ui) : (850 * accuracy + 6 * ui - 8 * ui); > + > + /* D-PHY chip spec : clk_t_lpx + clk_t_hs_prepare > 200ns */ > + /* D-PHY Specification : clk_t_lpx >= 50ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_lpx = (((2000 * accuracy - clk_t_hs_prepare) >= 500 * accuracy) ? > + ((2000 * accuracy - clk_t_hs_prepare)) : (500 * accuracy)) + > + mipi->clk_t_lpx_adjust * ui; > + > + /* D-PHY Specification : clk_t_hs_zero + clk_t_hs_prepare >= 300 ns */ > + /* clocked by TXBYTECLKHS */ > + clk_t_hs_zero = 3000 * accuracy - clk_t_hs_prepare + 3 * unit_tx_byte_clk_hs + mipi->clk_t_hs_zero_adjust * ui; > + > + /* D-PHY chip spec : data_t_lpx + data_t_hs_prepare > 200ns */ > + /* D-PHY Specification : data_t_lpx >= 50ns */ > + /* clocked by TXBYTECLKHS */ > + data_t_lpx = clk_t_lpx + mipi->data_t_lpx_adjust * ui; /* 2000 * accuracy - data_t_hs_prepare; */ > + > + /* D-PHY Specification : data_t_hs_zero + data_t_hs_prepare >= 145ns + 10*UI */ > + /* clocked by TXBYTECLKHS */ > + data_t_hs_zero = 1450 * accuracy + 10 * ui - data_t_hs_prepare + > + 3 * unit_tx_byte_clk_hs + mipi->data_t_hs_zero_adjust * ui; > + > + phy_ctrl->clk_pre_delay = DIV_ROUND_UP(clk_pre_delay, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_prepare = DIV_ROUND_UP(clk_t_hs_prepare, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_lpx = DIV_ROUND_UP(clk_t_lpx, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_zero = DIV_ROUND_UP(clk_t_hs_zero, unit_tx_byte_clk_hs); > + phy_ctrl->clk_t_hs_trial = DIV_ROUND_UP(clk_t_hs_trial, unit_tx_byte_clk_hs); > + > + phy_ctrl->data_post_delay = DIV_ROUND_UP(data_post_delay, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_prepare = DIV_ROUND_UP(data_t_hs_prepare, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_lpx = DIV_ROUND_UP(data_t_lpx, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_zero = DIV_ROUND_UP(data_t_hs_zero, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_hs_trial = DIV_ROUND_UP(data_t_hs_trial, unit_tx_byte_clk_hs); > + phy_ctrl->data_t_ta_go = 4; > + phy_ctrl->data_t_ta_get = 5; > + > + clk_pre_delay_reality = phy_ctrl->clk_pre_delay + 2; > + clk_t_hs_zero_reality = phy_ctrl->clk_t_hs_zero + 8; > + data_t_hs_zero_reality = phy_ctrl->data_t_hs_zero + 4; > + data_post_delay_reality = phy_ctrl->data_post_delay + 4; > + > + phy_ctrl->clk_post_delay = phy_ctrl->data_t_hs_trial + DIV_ROUND_UP(clk_post, unit_tx_byte_clk_hs); > + phy_ctrl->data_pre_delay = clk_pre_delay_reality + phy_ctrl->clk_t_lpx + > + phy_ctrl->clk_t_hs_prepare + clk_t_hs_zero_reality + DIV_ROUND_UP(clk_pre, unit_tx_byte_clk_hs); > + > + clk_post_delay_reality = phy_ctrl->clk_post_delay + 4; > + data_pre_delay_reality = phy_ctrl->data_pre_delay + 2; > + > + phy_ctrl->clk_lane_lp2hs_time = clk_pre_delay_reality + phy_ctrl->clk_t_lpx + > + phy_ctrl->clk_t_hs_prepare + clk_t_hs_zero_reality + 3; > + phy_ctrl->clk_lane_hs2lp_time = clk_post_delay_reality + phy_ctrl->clk_t_hs_trial + 3; > + phy_ctrl->data_lane_lp2hs_time = data_pre_delay_reality + phy_ctrl->data_t_lpx + > + phy_ctrl->data_t_hs_prepare + data_t_hs_zero_reality + 3; > + phy_ctrl->data_lane_hs2lp_time = data_post_delay_reality + phy_ctrl->data_t_hs_trial + 3; > + phy_ctrl->phy_stop_wait_time = clk_post_delay_reality + > + phy_ctrl->clk_t_hs_trial + DIV_ROUND_UP(clk_t_hs_exit, unit_tx_byte_clk_hs) - > + (data_post_delay_reality + phy_ctrl->data_t_hs_trial) + 3; > + > + phy_ctrl->lane_byte_clk = lane_clock / 8; > + phy_ctrl->clk_division = (((phy_ctrl->lane_byte_clk / 2) % mipi->max_tx_esc_clk) > 0) ? > + (phy_ctrl->lane_byte_clk / 2 / mipi->max_tx_esc_clk + 1) : > + (phy_ctrl->lane_byte_clk / 2 / mipi->max_tx_esc_clk); > + > + DRM_DEBUG("PHY clock_lane and data_lane config :\n" > + "rg_vrefsel_vcm=%u\n" > + "clk_pre_delay=%u\n" > + "clk_post_delay=%u\n" > + "clk_t_hs_prepare=%u\n" > + "clk_t_lpx=%u\n" > + "clk_t_hs_zero=%u\n" > + "clk_t_hs_trial=%u\n" > + "data_pre_delay=%u\n" > + "data_post_delay=%u\n" > + "data_t_hs_prepare=%u\n" > + "data_t_lpx=%u\n" > + "data_t_hs_zero=%u\n" > + "data_t_hs_trial=%u\n" > + "data_t_ta_go=%u\n" > + "data_t_ta_get=%u\n", > + phy_ctrl->rg_vrefsel_vcm, > + phy_ctrl->clk_pre_delay, > + phy_ctrl->clk_post_delay, > + phy_ctrl->clk_t_hs_prepare, > + phy_ctrl->clk_t_lpx, > + phy_ctrl->clk_t_hs_zero, > + phy_ctrl->clk_t_hs_trial, > + phy_ctrl->data_pre_delay, > + phy_ctrl->data_post_delay, > + phy_ctrl->data_t_hs_prepare, > + phy_ctrl->data_t_lpx, > + phy_ctrl->data_t_hs_zero, > + phy_ctrl->data_t_hs_trial, > + phy_ctrl->data_t_ta_go, > + phy_ctrl->data_t_ta_get); > + DRM_DEBUG("clk_lane_lp2hs_time=%u\n" > + "clk_lane_hs2lp_time=%u\n" > + "data_lane_lp2hs_time=%u\n" > + "data_lane_hs2lp_time=%u\n" > + "phy_stop_wait_time=%u\n", > + phy_ctrl->clk_lane_lp2hs_time, > + phy_ctrl->clk_lane_hs2lp_time, > + phy_ctrl->data_lane_lp2hs_time, > + phy_ctrl->data_lane_hs2lp_time, > + phy_ctrl->phy_stop_wait_time); > +} > + > +static void dw_dsi_set_mode(struct dw_dsi *dsi, enum dsi_work_mode mode) > +{ > + struct dsi_hw_ctx *ctx = dsi->ctx; > + void __iomem *base = ctx->base; > + > + writel(RESET, base + PWR_UP); > + writel(mode, base + MODE_CFG); > + writel(POWERUP, base + PWR_UP); > +} > + > +static void dsi_set_burst_mode(void __iomem *base, unsigned long burst_flags) > +{ > + unsigned long flags; > + u32 val; > + > + flags = burst_flags; > + flags &= MIPI_DSI_MODE_VIDEO | > + MIPI_DSI_MODE_VIDEO_BURST | > + MIPI_DSI_MODE_VIDEO_SYNC_PULSE; > + > + if (!(flags & MIPI_DSI_MODE_VIDEO)) { > + DRM_WARN("MIPI_DSI_MODE_VIDEO was not set! Using DSI_NON_BURST_SYNC_PULSES"); > + val = DSI_NON_BURST_SYNC_PULSES; > + } else if (flags & MIPI_DSI_MODE_VIDEO_BURST) { > + val = DSI_BURST_SYNC_PULSES_1; > + } else if (flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE) { > + val = DSI_NON_BURST_SYNC_PULSES; > + } else { > + val = DSI_NON_BURST_SYNC_EVENTS; > + } > + > + DRM_INFO("burst_mode = 0x%x (flags: 0x%04lx)", val, burst_flags); > + set_reg(base + MIPIDSI_VID_MODE_CFG_OFFSET, val, 2, 0); > +} > + > +/* > + * dsi phy reg write function > + */ > +static void dsi_phy_tst_set(void __iomem *base, u32 reg, u32 val) > +{ > + u32 reg_write = 0x10000 + reg; > + > + /* > + * latch reg first > + */ > + writel(reg_write, base + MIPIDSI_PHY_TST_CTRL1_OFFSET); > + writel(0x02, base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + writel(0x00, base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + > + /* > + * then latch value > + */ > + writel(val, base + MIPIDSI_PHY_TST_CTRL1_OFFSET); > + writel(0x02, base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + writel(0x00, base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > +} > + > +static void mipi_config_dphy_spec1v2_parameter(struct dw_dsi *dsi, > + char __iomem *mipi_dsi_base, > + u32 id) > +{ > + u32 i; > + u32 addr = 0; > + u32 lanes; > + > + lanes = dsi->client[id].lanes - 1; > + for (i = 0; i <= (lanes + 1); i++) { > + /* Lane Transmission Property */ > + addr = MIPIDSI_PHY_TST_LANE_TRANSMISSION_PROPERTY + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, 0x43); > + } > + > + /* pre_delay of clock lane request setting */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_PRE_DELAY, DSS_REDUCE(dsi->phy.clk_pre_delay)); > + > + /* post_delay of clock lane request setting */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_POST_DELAY, DSS_REDUCE(dsi->phy.clk_post_delay)); > + > + /* clock lane timing ctrl - t_lpx */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_TLPX, DSS_REDUCE(dsi->phy.clk_t_lpx)); > + > + /* clock lane timing ctrl - t_hs_prepare */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_PREPARE, DSS_REDUCE(dsi->phy.clk_t_hs_prepare)); > + > + /* clock lane timing ctrl - t_hs_zero */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_ZERO, DSS_REDUCE(dsi->phy.clk_t_hs_zero)); > + > + /* clock lane timing ctrl - t_hs_trial */ > + dsi_phy_tst_set(mipi_dsi_base, MIPIDSI_PHY_TST_CLK_TRAIL, DSS_REDUCE(dsi->phy.clk_t_hs_trial)); > + > + for (i = 0; i <= 4; i++) { > + if (lanes == 2 && i == 1) /* init mipi dsi 3 lanes should skip lane3 */ > + i++; > + > + if (i == 2) /* skip clock lane */ > + i++; /* addr: lane0:0x60; lane1:0x80; lane2:0xC0; lane3:0xE0 */ > + > + /* data lane pre_delay */ > + addr = MIPIDSI_PHY_TST_DATA_PRE_DELAY + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_pre_delay)); > + > + /* data lane post_delay */ > + addr = MIPIDSI_PHY_TST_DATA_POST_DELAY + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_post_delay)); > + > + /* data lane timing ctrl - t_lpx */ > + addr = MIPIDSI_PHY_TST_DATA_TLPX + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_t_lpx)); > + > + /* data lane timing ctrl - t_hs_prepare */ > + addr = MIPIDSI_PHY_TST_DATA_PREPARE + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_t_hs_prepare)); > + > + /* data lane timing ctrl - t_hs_zero */ > + addr = MIPIDSI_PHY_TST_DATA_ZERO + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_t_hs_zero)); > + > + /* data lane timing ctrl - t_hs_trial */ > + addr = MIPIDSI_PHY_TST_DATA_TRAIL + (i << 5); > + dsi_phy_tst_set(mipi_dsi_base, addr, DSS_REDUCE(dsi->phy.data_t_hs_trial)); > + > + DRM_DEBUG("DPHY spec1v2 config :\n" > + "addr=0x%x\n" > + "clk_pre_delay=%u\n" > + "clk_t_hs_trial=%u\n" > + "data_t_hs_zero=%u\n" > + "data_t_lpx=%u\n" > + "data_t_hs_prepare=%u\n", > + addr, > + dsi->phy.clk_pre_delay, > + dsi->phy.clk_t_hs_trial, > + dsi->phy.data_t_hs_zero, > + dsi->phy.data_t_lpx, > + dsi->phy.data_t_hs_prepare); > + } > +} > + > +static void dsi_mipi_init(struct dw_dsi *dsi, char __iomem *mipi_dsi_base, > + u32 id) > +{ > + struct dsi_hw_ctx *ctx = dsi->ctx; > + u32 hline_time = 0; > + u32 hsa_time = 0; > + u32 hbp_time = 0; > + u64 pixel_clk = 0; > + unsigned long dw_jiffies = 0; > + u32 tmp = 0; > + bool is_ready = false; > + struct mipi_panel_info *mipi = NULL; > + struct dss_rect rect; > + u32 cmp_stopstate_val = 0; > + u32 lanes; > + > + WARN_ON(!dsi); > + WARN_ON(!mipi_dsi_base); > + > + DRM_INFO("%s: id=%d\n", __func__, id); > + > + mipi = &dsi->mipi; > + > + if (mipi->max_tx_esc_clk == 0) { > + DRM_INFO("max_tx_esc_clk is invalid!"); > + mipi->max_tx_esc_clk = DEFAULT_MAX_TX_ESC_CLK; > + } > + > + memset(&dsi->phy, 0, sizeof(struct mipi_phy_params)); > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) > + kirin970_get_dsi_dphy_ctrl(dsi, &dsi->phy, id); > + else > + kirin960_get_dsi_phy_ctrl(dsi, &dsi->phy, id); > + > + rect.x = 0; > + rect.y = 0; > + rect.w = dsi->cur_mode.hdisplay; > + rect.h = dsi->cur_mode.vdisplay; > + lanes = dsi->client[id].lanes - 1; > + /***************Configure the DPHY start**************/ > + > + set_reg(mipi_dsi_base + MIPIDSI_PHY_IF_CFG_OFFSET, lanes, 2, 0); > + set_reg(mipi_dsi_base + MIPIDSI_CLKMGR_CFG_OFFSET, dsi->phy.clk_division, 8, 0); > + set_reg(mipi_dsi_base + MIPIDSI_CLKMGR_CFG_OFFSET, dsi->phy.clk_division, 8, 8); > + > + writel(0x00000000, mipi_dsi_base + MIPIDSI_PHY_RSTZ_OFFSET); > + > + writel(0x00000000, mipi_dsi_base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + writel(0x00000001, mipi_dsi_base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + writel(0x00000000, mipi_dsi_base + MIPIDSI_PHY_TST_CTRL0_OFFSET); > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) { > + dsi_phy_tst_set(mipi_dsi_base, 0x0042, 0x21); > + /* PLL configuration I */ > + dsi_phy_tst_set(mipi_dsi_base, 0x0046, > + dsi->phy.rg_cp + (dsi->phy.rg_lpf_r << 4)); > + > + /* PLL configuration II */ > + dsi_phy_tst_set(mipi_dsi_base, 0x0048, > + dsi->phy.rg_0p8v + (dsi->phy.rg_2p5g << 1) + > + (dsi->phy.rg_320m << 2) + (dsi->phy.rg_band_sel << 3)); > + > + /* PLL configuration III */ > + dsi_phy_tst_set(mipi_dsi_base, 0x0049, dsi->phy.rg_pre_div); > + > + /* PLL configuration IV */ > + dsi_phy_tst_set(mipi_dsi_base, 0x004A, dsi->phy.rg_div); > + > + dsi_phy_tst_set(mipi_dsi_base, 0x004F, 0xf0); > + dsi_phy_tst_set(mipi_dsi_base, 0x0050, 0xc0); > + dsi_phy_tst_set(mipi_dsi_base, 0x0051, 0x22); > + > + dsi_phy_tst_set(mipi_dsi_base, 0x0053, dsi->phy.rg_vrefsel_vcm); > + > + /* enable BTA */ > + dsi_phy_tst_set(mipi_dsi_base, 0x0054, 0x03); > + > + /* PLL update control */ > + dsi_phy_tst_set(mipi_dsi_base, 0x004B, 0x1); > + > + /* set dphy spec parameter */ > + mipi_config_dphy_spec1v2_parameter(dsi, mipi_dsi_base, id); > + } else { > + int i = 0; > + > + /* physical configuration PLL I */ > + dsi_phy_tst_set(mipi_dsi_base, 0x14, > + (dsi->phy.rg_pll_fbd_s << 4) + (dsi->phy.rg_pll_enswc << 3) + > + (dsi->phy.rg_pll_enbwt << 2) + dsi->phy.rg_pll_chp); > + > + /* physical configuration PLL II, M */ > + dsi_phy_tst_set(mipi_dsi_base, 0x15, dsi->phy.rg_pll_fbd_p); > + > + /* physical configuration PLL III */ > + dsi_phy_tst_set(mipi_dsi_base, 0x16, > + (dsi->phy.rg_pll_cp << 5) + (dsi->phy.rg_pll_lpf_cs << 4) + > + dsi->phy.rg_pll_refsel); > + > + /* physical configuration PLL IV, N */ > + dsi_phy_tst_set(mipi_dsi_base, 0x17, dsi->phy.rg_pll_pre_p); > + > + /* sets the analog characteristic of V reference in D-PHY TX */ > + dsi_phy_tst_set(mipi_dsi_base, 0x1D, dsi->phy.rg_vrefsel_vcm); > + > + /* MISC AFE Configuration */ > + dsi_phy_tst_set(mipi_dsi_base, 0x1E, > + (dsi->phy.rg_pll_cp_p << 5) + (dsi->phy.reload_sel << 4) + > + (dsi->phy.rg_phase_gen_en << 3) + (dsi->phy.rg_band_sel << 2) + > + (dsi->phy.pll_power_down << 1) + dsi->phy.pll_register_override); > + > + /* reload_command */ > + dsi_phy_tst_set(mipi_dsi_base, 0x1F, dsi->phy.load_command); > + > + /* pre_delay of clock lane request setting */ > + dsi_phy_tst_set(mipi_dsi_base, 0x20, DSS_REDUCE(dsi->phy.clk_pre_delay)); > + > + /* post_delay of clock lane request setting */ > + dsi_phy_tst_set(mipi_dsi_base, 0x21, DSS_REDUCE(dsi->phy.clk_post_delay)); > + > + /* clock lane timing ctrl - t_lpx */ > + dsi_phy_tst_set(mipi_dsi_base, 0x22, DSS_REDUCE(dsi->phy.clk_t_lpx)); > + > + /* clock lane timing ctrl - t_hs_prepare */ > + dsi_phy_tst_set(mipi_dsi_base, 0x23, DSS_REDUCE(dsi->phy.clk_t_hs_prepare)); > + > + /* clock lane timing ctrl - t_hs_zero */ > + dsi_phy_tst_set(mipi_dsi_base, 0x24, DSS_REDUCE(dsi->phy.clk_t_hs_zero)); > + > + /* clock lane timing ctrl - t_hs_trial */ > + dsi_phy_tst_set(mipi_dsi_base, 0x25, dsi->phy.clk_t_hs_trial); > + > + for (i = 0; i <= lanes; i++) { > + /* data lane pre_delay */ > + tmp = 0x30 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_pre_delay)); > + > + /* data lane post_delay */ > + tmp = 0x31 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_post_delay)); > + > + /* data lane timing ctrl - t_lpx */ > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_lpx)); > + > + /* data lane timing ctrl - t_hs_prepare */ > + tmp = 0x33 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_hs_prepare)); > + > + /* data lane timing ctrl - t_hs_zero */ > + tmp = 0x34 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_hs_zero)); > + > + /* data lane timing ctrl - t_hs_trial */ > + tmp = 0x35 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_hs_trial)); > + > + /* data lane timing ctrl - t_ta_go */ > + tmp = 0x36 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_ta_go)); > + > + /* data lane timing ctrl - t_ta_get */ > + tmp = 0x37 + (i << 4); > + dsi_phy_tst_set(mipi_dsi_base, tmp, DSS_REDUCE(dsi->phy.data_t_ta_get)); > + } > + } > + > + writel(0x00000007, mipi_dsi_base + MIPIDSI_PHY_RSTZ_OFFSET); > + > + is_ready = false; > + dw_jiffies = jiffies + HZ / 2; > + do { > + tmp = readl(mipi_dsi_base + MIPIDSI_PHY_STATUS_OFFSET); > + if ((tmp & 0x00000001) == 0x00000001) { > + is_ready = true; > + break; > + } > + } while (time_after(dw_jiffies, jiffies)); Use jiffies + msecs_to_jiffies(xxx) - and drop HZ /2. Same goes for other similar HZ uses. > + > + if (!is_ready) { > + DRM_INFO("phylock is not ready!MIPIDSI_PHY_STATUS_OFFSET=0x%x.\n", > + tmp); > + } > + > + if (lanes >= DSI_4_LANES) > + cmp_stopstate_val = (BIT(4) | BIT(7) | BIT(9) | BIT(11)); > + else if (lanes >= DSI_3_LANES) > + cmp_stopstate_val = (BIT(4) | BIT(7) | BIT(9)); > + else if (lanes >= DSI_2_LANES) > + cmp_stopstate_val = (BIT(4) | BIT(7)); > + else > + cmp_stopstate_val = (BIT(4)); > + > + is_ready = false; > + dw_jiffies = jiffies + HZ / 2; > + do { > + tmp = readl(mipi_dsi_base + MIPIDSI_PHY_STATUS_OFFSET); > + if ((tmp & cmp_stopstate_val) == cmp_stopstate_val) { > + is_ready = true; > + break; > + } > + } while (time_after(dw_jiffies, jiffies)); > + > + if (!is_ready) { > + DRM_INFO("phystopstateclklane is not ready! MIPIDSI_PHY_STATUS_OFFSET=0x%x.\n", > + tmp); > + } > + > + /*************************Configure the DPHY end*************************/ > + > + /* phy_stop_wait_time */ > + set_reg(mipi_dsi_base + MIPIDSI_PHY_IF_CFG_OFFSET, dsi->phy.phy_stop_wait_time, 8, 8); > + > + /*--------------configuring the DPI packet transmission---------------- */ > + > + /* > + * 2. Configure the DPI Interface: > + * This defines how the DPI interface interacts with the controller. > + */ > + set_reg(mipi_dsi_base + MIPIDSI_DPI_VCID_OFFSET, mipi->vc, 2, 0); > + set_reg(mipi_dsi_base + MIPIDSI_DPI_COLOR_CODING_OFFSET, mipi->color_mode, 4, 0); > + > + set_reg(mipi_dsi_base + MIPIDSI_DPI_CFG_POL_OFFSET, dsi->ldi.data_en_plr, 1, 0); > + set_reg(mipi_dsi_base + MIPIDSI_DPI_CFG_POL_OFFSET, dsi->ldi.vsync_plr, 1, 1); > + set_reg(mipi_dsi_base + MIPIDSI_DPI_CFG_POL_OFFSET, dsi->ldi.hsync_plr, 1, 2); > + set_reg(mipi_dsi_base + MIPIDSI_DPI_CFG_POL_OFFSET, 0x0, 1, 3); > + set_reg(mipi_dsi_base + MIPIDSI_DPI_CFG_POL_OFFSET, 0x0, 1, 4); > + > + /* > + * 3. Select the Video Transmission Mode: > + * This defines how the processor requires the video line to be > + * transported through the DSI link. > + */ > + /* video mode: low power mode */ > + set_reg(mipi_dsi_base + MIPIDSI_VID_MODE_CFG_OFFSET, 0x3f, 6, 8); > + > + /* TODO: fix blank display bug when set backlight */ > + set_reg(mipi_dsi_base + MIPIDSI_DPI_LP_CMD_TIM_OFFSET, 0x4, 8, 16); > + /* video mode: send read cmd by lp mode */ > + set_reg(mipi_dsi_base + MIPIDSI_VID_MODE_CFG_OFFSET, 0x1, 1, 15); > + > + set_reg(mipi_dsi_base + MIPIDSI_VID_PKT_SIZE_OFFSET, rect.w, 14, 0); > + > + /* burst mode */ > + dsi_set_burst_mode(mipi_dsi_base, dsi->client[id].mode_flags); > + /* for dsi read, BTA enable */ > + set_reg(mipi_dsi_base + MIPIDSI_PCKHDL_CFG_OFFSET, 0x1, 1, 2); > + > + /* > + * 4. Define the DPI Horizontal timing configuration: > + * > + * Hsa_time = HSA*(PCLK period/Clk Lane Byte Period); > + * Hbp_time = HBP*(PCLK period/Clk Lane Byte Period); > + * Hline_time = (HSA+HBP+HACT+HFP)*(PCLK period/Clk Lane Byte Period); > + */ > + pixel_clk = dsi->cur_mode.clock * 1000; > + /* htot = dsi->cur_mode.htotal; */ > + /* vtot = dsi->cur_mode.vtotal; */ > + dsi->ldi.h_front_porch = dsi->cur_mode.hsync_start - dsi->cur_mode.hdisplay; > + dsi->ldi.h_back_porch = dsi->cur_mode.htotal - dsi->cur_mode.hsync_end; > + dsi->ldi.h_pulse_width = dsi->cur_mode.hsync_end - dsi->cur_mode.hsync_start; > + dsi->ldi.v_front_porch = dsi->cur_mode.vsync_start - dsi->cur_mode.vdisplay; > + dsi->ldi.v_back_porch = dsi->cur_mode.vtotal - dsi->cur_mode.vsync_end; > + dsi->ldi.v_pulse_width = dsi->cur_mode.vsync_end - dsi->cur_mode.vsync_start; > + if (dsi->ldi.v_pulse_width > 15) { > + DRM_DEBUG_DRIVER("vsw exceeded 15\n"); > + dsi->ldi.v_pulse_width = 15; > + } > + hsa_time = dsi->ldi.h_pulse_width * dsi->phy.lane_byte_clk / pixel_clk; > + hbp_time = dsi->ldi.h_back_porch * dsi->phy.lane_byte_clk / pixel_clk; > + hline_time = DIV_ROUND_UP((dsi->ldi.h_pulse_width + dsi->ldi.h_back_porch + > + rect.w + dsi->ldi.h_front_porch) * dsi->phy.lane_byte_clk, pixel_clk); > + > + DRM_INFO("hsa_time=%d, hbp_time=%d, hline_time=%d\n", > + hsa_time, hbp_time, hline_time); > + DRM_INFO("lane_byte_clk=%llu, pixel_clk=%llu\n", > + dsi->phy.lane_byte_clk, pixel_clk); > + set_reg(mipi_dsi_base + MIPIDSI_VID_HSA_TIME_OFFSET, hsa_time, 12, 0); > + set_reg(mipi_dsi_base + MIPIDSI_VID_HBP_TIME_OFFSET, hbp_time, 12, 0); > + set_reg(mipi_dsi_base + MIPIDSI_VID_HLINE_TIME_OFFSET, hline_time, 15, 0); > + > + /* Define the Vertical line configuration */ > + set_reg(mipi_dsi_base + MIPIDSI_VID_VSA_LINES_OFFSET, > + dsi->ldi.v_pulse_width, 10, 0); > + set_reg(mipi_dsi_base + MIPIDSI_VID_VBP_LINES_OFFSET, > + dsi->ldi.v_back_porch, 10, 0); > + set_reg(mipi_dsi_base + MIPIDSI_VID_VFP_LINES_OFFSET, > + dsi->ldi.v_front_porch, 10, 0); > + set_reg(mipi_dsi_base + MIPIDSI_VID_VACTIVE_LINES_OFFSET, > + rect.h, 14, 0); > + set_reg(mipi_dsi_base + MIPIDSI_TO_CNT_CFG_OFFSET, > + 0x7FF, 16, 0); > + > + /* Configure core's phy parameters */ > + set_reg(mipi_dsi_base + MIPIDSI_PHY_TMR_LPCLK_CFG_OFFSET, > + dsi->phy.clk_lane_lp2hs_time, 10, 0); > + set_reg(mipi_dsi_base + MIPIDSI_PHY_TMR_LPCLK_CFG_OFFSET, > + dsi->phy.clk_lane_hs2lp_time, 10, 16); > + > + set_reg(mipi_dsi_base + MIPIDSI_PHY_TMR_RD_CFG_OFFSET, > + 0x7FFF, 15, 0); > + set_reg(mipi_dsi_base + MIPIDSI_PHY_TMR_CFG_OFFSET, > + dsi->phy.data_lane_lp2hs_time, 10, 0); > + set_reg(mipi_dsi_base + MIPIDSI_PHY_TMR_CFG_OFFSET, > + dsi->phy.data_lane_hs2lp_time, 10, 16); > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) { > + /* 16~19bit:pclk_en, pclk_sel, dpipclk_en, dpipclk_sel */ > + set_reg(mipi_dsi_base + MIPIDSI_CLKMGR_CFG_OFFSET, 0x5, 4, 16); > + /* 0:dphy */ > + set_reg(mipi_dsi_base + KIRIN970_PHY_MODE, 0x0, 1, 0); > + } > + > + /* Waking up Core */ > + set_reg(mipi_dsi_base + MIPIDSI_PWR_UP_OFFSET, 0x1, 1, 0); > +} > + > +static void dsi_encoder_disable(struct drm_encoder *encoder) > +{ > + struct dw_dsi *dsi = encoder_to_dsi(encoder); > + struct dsi_hw_ctx *ctx = dsi->ctx; > + void __iomem *base = ctx->base; > + > + if (!dsi->enable) > + return; > + > + dw_dsi_set_mode(dsi, DSI_COMMAND_MODE); > + /* turn off panel's backlight */ > + if (dsi->panel && drm_panel_disable(dsi->panel)) > + DRM_ERROR("failed to disable panel\n"); > + > + /* turn off panel */ > + if (dsi->panel && drm_panel_unprepare(dsi->panel)) > + DRM_ERROR("failed to unprepare panel\n"); > + > + writel(0, base + PWR_UP); > + writel(0, base + LPCLK_CTRL); > + writel(0, base + PHY_RSTZ); > + clk_disable_unprepare(ctx->dss_dphy0_ref_clk); > + clk_disable_unprepare(ctx->dss_dphy0_cfg_clk); > + clk_disable_unprepare(ctx->dss_pclk_dsi0_clk); > + > + dsi->enable = false; > +} > + > +static int mipi_dsi_on_sub1(struct dw_dsi *dsi, char __iomem *mipi_dsi_base, > + u32 id) > +{ > + struct dsi_hw_ctx *ctx = dsi->ctx; > + > + WARN_ON(!mipi_dsi_base); > + > + /* mipi init */ > + dsi_mipi_init(dsi, mipi_dsi_base, id); > + > + /* dsi memory init */ > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) > + writel(0x02600008, mipi_dsi_base + KIRIN970_DSI_MEM_CTRL); > + > + /* switch to cmd mode */ > + set_reg(mipi_dsi_base + MIPIDSI_MODE_CFG_OFFSET, 0x1, 1, 0); > + /* cmd mode: low power mode */ > + set_reg(mipi_dsi_base + MIPIDSI_CMD_MODE_CFG_OFFSET, 0x7f, 7, 8); > + set_reg(mipi_dsi_base + MIPIDSI_CMD_MODE_CFG_OFFSET, 0xf, 4, 16); > + set_reg(mipi_dsi_base + MIPIDSI_CMD_MODE_CFG_OFFSET, 0x1, 1, 24); > + /* disable generate High Speed clock */ > + /* delete? */ > + set_reg(mipi_dsi_base + MIPIDSI_LPCLK_CTRL_OFFSET, 0x0, 1, 0); > + > + return 0; > +} > + > +static int mipi_dsi_on_sub2(struct dw_dsi *dsi, char __iomem *mipi_dsi_base) > +{ > + struct dsi_hw_ctx *ctx = dsi->ctx; > + > + u64 pctrl_dphytx_stopcnt = 0; > + > + WARN_ON(!mipi_dsi_base); > + > + /* switch to video mode */ > + set_reg(mipi_dsi_base + MIPIDSI_MODE_CFG_OFFSET, 0x0, 1, 0); > + > + /* enable EOTP TX */ > + set_reg(mipi_dsi_base + MIPIDSI_PCKHDL_CFG_OFFSET, 0x1, 1, 0); > + > + /* enable generate High Speed clock, continue clock */ > + set_reg(mipi_dsi_base + MIPIDSI_LPCLK_CTRL_OFFSET, 0x1, 2, 0); > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) { > + /* init: wait DPHY 4 data lane stopstate */ > + pctrl_dphytx_stopcnt = (u64)(dsi->ldi.h_back_porch + > + dsi->ldi.h_front_porch + dsi->ldi.h_pulse_width + dsi->cur_mode.hdisplay + 5) * > + DEFAULT_PCLK_PCTRL_RATE / (dsi->cur_mode.clock * 1000); > + DRM_DEBUG("pctrl_dphytx_stopcnt = %llu\n", pctrl_dphytx_stopcnt); > + > + /* FIXME: */ > + writel((u32)pctrl_dphytx_stopcnt, dsi->ctx->pctrl_base + PERI_CTRL29); > + } > + > + return 0; > +} > + > +static void dsi_encoder_enable(struct drm_encoder *encoder) > +{ > + struct dw_dsi *dsi = encoder_to_dsi(encoder); > + struct dsi_hw_ctx *ctx = dsi->ctx; > + int ret; > + > + if (dsi->enable) > + return; > + > + ret = clk_prepare_enable(ctx->dss_dphy0_ref_clk); > + if (ret) { > + DRM_ERROR("fail to enable dss_dphy0_ref_clk: %d\n", ret); > + return; > + } > + > + ret = clk_prepare_enable(ctx->dss_dphy0_cfg_clk); > + if (ret) { > + DRM_ERROR("fail to enable dss_dphy0_cfg_clk: %d\n", ret); > + return; > + } > + > + ret = clk_prepare_enable(ctx->dss_pclk_dsi0_clk); > + if (ret) { > + DRM_ERROR("fail to enable dss_pclk_dsi0_clk: %d\n", ret); > + return; > + } > + > + mipi_dsi_on_sub1(dsi, ctx->base, dsi->attached_client); > + > + mipi_dsi_on_sub2(dsi, ctx->base); > + > + /* turn on panel */ > + if (dsi->panel && drm_panel_prepare(dsi->panel)) > + DRM_ERROR("failed to prepare panel\n"); > + > + /* dw_dsi_set_mode(dsi, DSI_VIDEO_MODE); */ > + > + /* turn on panel's back light */ > + if (dsi->panel && drm_panel_enable(dsi->panel)) > + DRM_ERROR("failed to enable panel\n"); > + > + dsi->enable = true; > +} > + > +static enum drm_mode_status dsi_encoder_mode_valid(struct drm_encoder *encoder, > + const struct drm_display_mode *mode) > + > +{ > + const struct drm_crtc_helper_funcs *crtc_funcs; > + struct drm_display_mode adj_mode; > + int clock = mode->clock; > + struct drm_crtc *crtc; > + > + drm_for_each_crtc(crtc, encoder->dev) { > + drm_mode_copy(&adj_mode, mode); > + > + crtc_funcs = crtc->helper_private; > + if (crtc_funcs && crtc_funcs->mode_fixup) { > + if (!crtc_funcs->mode_fixup(crtc, mode, &adj_mode)) { > + DRM_INFO("Discarded mode: %ix%i@%i, clock: %i (adjusted to %i)", > + mode->hdisplay, mode->vdisplay, > + drm_mode_vrefresh(mode), > + mode->clock, clock); > + > + return MODE_BAD; > + } > + clock = adj_mode.clock; > + } > + } > + > + DRM_INFO("Valid mode: %ix%i@%i, clock %i (adjusted to %i)", > + mode->hdisplay, mode->vdisplay, drm_mode_vrefresh(mode), > + mode->clock, clock); > + > + return MODE_OK; > +} > + > +static void dsi_encoder_mode_set(struct drm_encoder *encoder, > + struct drm_display_mode *mode, > + struct drm_display_mode *adj_mode) > +{ > + struct dw_dsi *dsi = encoder_to_dsi(encoder); > + > + drm_mode_copy(&dsi->cur_mode, adj_mode); > +} > + > +static int dsi_encoder_atomic_check(struct drm_encoder *encoder, > + struct drm_crtc_state *crtc_state, > + struct drm_connector_state *conn_state) > +{ > + /* do nothing */ > + return 0; > +} > + > +static const struct drm_encoder_helper_funcs dw_encoder_helper_funcs = { > + .atomic_check = dsi_encoder_atomic_check, > + .mode_valid = dsi_encoder_mode_valid, > + .mode_set = dsi_encoder_mode_set, > + .enable = dsi_encoder_enable, > + .disable = dsi_encoder_disable > +}; > + > +static const struct drm_encoder_funcs dw_encoder_funcs = { > + .destroy = drm_encoder_cleanup, > +}; > + > +static int dw_drm_encoder_init(struct device *dev, > + struct drm_device *drm_dev, > + struct drm_encoder *encoder, > + struct drm_bridge *bridge) > +{ > + int ret; > + u32 crtc_mask; > + > + drm_info(drm_dev, "%s:\n", __func__); > + > + /* Link drm_bridge to encoder */ > + if (!bridge) { > + drm_info(drm_dev, "no dsi bridge to attach the encoder\n"); > + return 0; > + } > + > + crtc_mask = drm_of_find_possible_crtcs(drm_dev, dev->of_node); > + if (!crtc_mask) { > + DRM_ERROR("failed to find crtc mask\n"); > + return -EINVAL; > + } > + > + drm_info(drm_dev, "Initializing CRTC encoder: %d\n", > + crtc_mask); > + > + encoder->possible_crtcs = crtc_mask; > + encoder->possible_clones = 0; > + ret = drm_encoder_init(drm_dev, encoder, &dw_encoder_funcs, > + DRM_MODE_ENCODER_DSI, NULL); > + if (ret) { > + drm_info(drm_dev, "failed to init dsi encoder\n"); > + return ret; > + } > + > + drm_encoder_helper_add(encoder, &dw_encoder_helper_funcs); > + > + /* associate the bridge to dsi encoder */ > + ret = drm_bridge_attach(encoder, bridge, NULL, 0); > + if (ret) { > + drm_info(drm_dev, "failed to attach external bridge\n"); > + drm_encoder_cleanup(encoder); > + } > + > + return ret; > +} All the encoder stuff can, I think, be repalced by the simple encoder. See how other drivers uses drm_simple_encoder_init() > + > +static int dsi_host_attach(struct mipi_dsi_host *host, > + struct mipi_dsi_device *mdsi) > +{ > + struct dw_dsi *dsi = host_to_dsi(host); > + u32 id = mdsi->channel >= 1 ? OUT_PANEL : OUT_HDMI; > + > + if (mdsi->lanes < 1 || mdsi->lanes > 4) { > + DRM_ERROR("dsi device params invalid\n"); > + return -EINVAL; > + } > + > + dsi->client[id].lanes = mdsi->lanes; > + dsi->client[id].format = mdsi->format; > + dsi->client[id].mode_flags = mdsi->mode_flags; > + dsi->client[id].phy_clock = 0; > + > + dsi->attached_client = id; > + > + DRM_DEBUG("host attach, client name=[%s], id=%d\n", mdsi->name, id); > + > + return 0; > +} > + > +static int dsi_host_detach(struct mipi_dsi_host *host, > + struct mipi_dsi_device *mdsi) > +{ > + /* do nothing */ > + return 0; > +} > + > +static int dsi_gen_pkt_hdr_write(void __iomem *base, u32 val) > +{ > + u32 status; > + int ret; > + > + ret = readx_poll_timeout(readl, base + CMD_PKT_STATUS, status, > + !(status & GEN_CMD_FULL), 1000, > + CMD_PKT_STATUS_TIMEOUT_US); > + if (ret < 0) { > + DRM_ERROR("failed to get available command FIFO\n"); > + return ret; > + } > + > + writel(val, base + GEN_HDR); > + > + ret = readx_poll_timeout(readl, base + CMD_PKT_STATUS, status, > + status & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY), > + 1000, CMD_PKT_STATUS_TIMEOUT_US); > + if (ret < 0) { > + DRM_ERROR("failed to write command FIFO\n"); > + return ret; > + } > + > + return 0; > +} > + > +static int dsi_dcs_short_write(void __iomem *base, > + const struct mipi_dsi_msg *msg) > +{ > + const u16 *tx_buf = msg->tx_buf; > + u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type); > + > + if (msg->tx_len > 2) { > + DRM_ERROR("too long tx buf length %zu for short write\n", > + msg->tx_len); > + return -EINVAL; > + } > + > + return dsi_gen_pkt_hdr_write(base, val); > +} > + > +static int dsi_dcs_long_write(void __iomem *base, > + const struct mipi_dsi_msg *msg) > +{ > + const u32 *tx_buf = msg->tx_buf; > + int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret; > + u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type); > + u32 remainder = 0; > + u32 status; > + > + if (msg->tx_len < 3) { > + DRM_ERROR("wrong tx buf length %zu for long write\n", > + msg->tx_len); > + return -EINVAL; > + } > + > + while (DIV_ROUND_UP(len, pld_data_bytes)) { > + if (len < pld_data_bytes) { > + memcpy(&remainder, tx_buf, len); > + writel(remainder, base + GEN_PLD_DATA); > + len = 0; > + } else { > + writel(*tx_buf, base + GEN_PLD_DATA); > + tx_buf++; > + len -= pld_data_bytes; > + } > + > + ret = readx_poll_timeout(readl, base + CMD_PKT_STATUS, > + status, !(status & GEN_PLD_W_FULL), 1000, > + CMD_PKT_STATUS_TIMEOUT_US); > + if (ret < 0) { > + DRM_ERROR("failed to get available write payload FIFO\n"); > + return ret; > + } > + } > + > + return dsi_gen_pkt_hdr_write(base, val); > +} > + > +static ssize_t dsi_host_transfer(struct mipi_dsi_host *host, > + const struct mipi_dsi_msg *msg) > +{ > + struct dw_dsi *dsi = host_to_dsi(host); > + struct dsi_hw_ctx *ctx = dsi->ctx; > + void __iomem *base = ctx->base; > + int ret; > + > + switch (msg->type) { > + case MIPI_DSI_DCS_SHORT_WRITE: > + case MIPI_DSI_DCS_SHORT_WRITE_PARAM: > + case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE: > + ret = dsi_dcs_short_write(base, msg); > + break; > + case MIPI_DSI_DCS_LONG_WRITE: > + ret = dsi_dcs_long_write(base, msg); > + break; > + default: > + DRM_ERROR("unsupported message type\n"); > + ret = -EINVAL; > + } > + > + return ret; > +} > + > +static const struct mipi_dsi_host_ops dsi_host_ops = { > + .attach = dsi_host_attach, > + .detach = dsi_host_detach, > + .transfer = dsi_host_transfer, > +}; > + > +static int dsi_host_init(struct device *dev, struct dw_dsi *dsi) > +{ > + struct mipi_dsi_host *host = &dsi->host; > + struct mipi_panel_info *mipi = &dsi->mipi; > + int ret; > + > + host->dev = dev; > + host->ops = &dsi_host_ops; > + > + mipi->max_tx_esc_clk = 10 * 1000000UL; > + mipi->vc = 0; > + mipi->color_mode = DSI_24BITS_1; > + mipi->clk_post_adjust = 120; > + mipi->clk_pre_adjust = 0; > + mipi->clk_t_hs_prepare_adjust = 0; > + mipi->clk_t_lpx_adjust = 0; > + mipi->clk_t_hs_trial_adjust = 0; > + mipi->clk_t_hs_exit_adjust = 0; > + mipi->clk_t_hs_zero_adjust = 0; > + > + dsi->ldi.data_en_plr = 0; > + dsi->ldi.vsync_plr = 0; > + dsi->ldi.hsync_plr = 0; > + > + ret = mipi_dsi_host_register(host); > + if (ret) { > + dev_info(dev, "failed to register dsi host\n"); > + return ret; > + } > + > + return 0; > +} > + > +static int dsi_connector_get_modes(struct drm_connector *connector) > +{ > + struct dw_dsi *dsi = connector_to_dsi(connector); > + > + return drm_panel_get_modes(dsi->panel, connector); > +} > + > +static enum drm_mode_status > +dsi_connector_mode_valid(struct drm_connector *connector, > + struct drm_display_mode *mode) > +{ > + enum drm_mode_status mode_status = MODE_OK; > + > + return mode_status; > +} > + > +static struct drm_encoder * > +dsi_connector_best_encoder(struct drm_connector *connector) > +{ > + struct dw_dsi *dsi = connector_to_dsi(connector); > + > + return &dsi->encoder; > +} > + > +static const struct drm_connector_helper_funcs dsi_connector_helper_funcs = { > + .get_modes = dsi_connector_get_modes, > + .mode_valid = dsi_connector_mode_valid, > + .best_encoder = dsi_connector_best_encoder, > +}; > + > +static enum drm_connector_status > +dsi_connector_detect(struct drm_connector *connector, bool force) > +{ > + struct dw_dsi *dsi = connector_to_dsi(connector); > + enum drm_connector_status status; > + > + status = dsi->cur_client == OUT_PANEL ? connector_status_connected : > + connector_status_disconnected; > + > + return status; > +} > + > +static void dsi_connector_destroy(struct drm_connector *connector) > +{ > + drm_connector_unregister(connector); > + drm_connector_cleanup(connector); > +} > + > +static struct drm_connector_funcs dsi_atomic_connector_funcs = { > + .fill_modes = drm_helper_probe_single_connector_modes, > + .detect = dsi_connector_detect, > + .destroy = dsi_connector_destroy, > + .reset = drm_atomic_helper_connector_reset, > + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, > + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, > +}; > + > +static int dsi_connector_init(struct drm_device *dev, struct dw_dsi *dsi) > +{ > + struct drm_encoder *encoder = &dsi->encoder; > + struct drm_connector *connector = &dsi->connector; > + int ret; > + > + connector->polled = DRM_CONNECTOR_POLL_HPD; > + drm_connector_helper_add(connector, > + &dsi_connector_helper_funcs); > + > + ret = drm_connector_init(dev, &dsi->connector, > + &dsi_atomic_connector_funcs, > + DRM_MODE_CONNECTOR_DSI); > + if (ret) > + return ret; > + > + drm_dbg(dev, "Attaching CRTC encoder\n"); > + ret = drm_connector_attach_encoder(connector, encoder); > + if (ret) > + return ret; > + > + ret = drm_panel_attach(dsi->panel, connector); > + if (ret) > + return ret; > + > + drm_connector_register(&dsi->connector); > + > + drm_dbg(dev, "connector init\n"); > + return 0; > +} > + > +static int dsi_bind(struct device *dev, struct device *master, void *data) > +{ > + struct dsi_data *ddata = dev_get_drvdata(dev); > + struct dw_dsi *dsi = &ddata->dsi; > + struct drm_device *drm_dev = data; > + int ret; > + > + ret = dw_drm_encoder_init(dev, drm_dev, &dsi->encoder, > + dsi->bridge); > + if (ret) > + return ret; > + > + if (dsi->panel) { > + ret = dsi_connector_init(drm_dev, dsi); > + if (ret) > + return ret; > + } > + > + return 0; > +} > + > +static void dsi_unbind(struct device *dev, struct device *master, void *data) > +{ > + /* do nothing */ > +} > + > +static const struct component_ops dsi_ops = { > + .bind = dsi_bind, > + .unbind = dsi_unbind, > +}; > + > +static int dsi_parse_bridge_endpoint(struct dw_dsi *dsi, > + struct device_node *endpoint) > +{ > + struct device_node *bridge_node; > + struct drm_bridge *bridge; > + > + bridge_node = of_graph_get_remote_port_parent(endpoint); > + if (!bridge_node) { > + DRM_ERROR("no valid bridge node\n"); > + return -ENODEV; > + } > + of_node_put(bridge_node); > + > + bridge = of_drm_find_bridge(bridge_node); > + if (!bridge) { > + DRM_INFO("wait for external HDMI bridge driver.\n"); > + return -EPROBE_DEFER; > + } > + dsi->bridge = bridge; > + > + return 0; > +} > + > +static int dsi_parse_panel_endpoint(struct dw_dsi *dsi, > + struct device_node *endpoint) > +{ > + struct device_node *panel_node; > + struct drm_panel *panel; > + > + panel_node = of_graph_get_remote_port_parent(endpoint); > + if (!panel_node) { > + DRM_ERROR("no valid panel node\n"); > + return -ENODEV; > + } > + of_node_put(panel_node); > + > + panel = of_drm_find_panel(panel_node); > + if (!panel) { > + DRM_DEBUG_DRIVER("skip this panel endpoint.\n"); > + return 0; > + } > + dsi->panel = panel; > + > + return 0; > +} > + > +static int dsi_parse_endpoint(struct dw_dsi *dsi, > + struct device_node *np, > + enum dsi_output_client client) > +{ > + struct device_node *ep_node; > + struct of_endpoint ep; > + int ret = 0; > + > + if (client == OUT_MAX) > + return -EINVAL; > + > + for_each_endpoint_of_node(np, ep_node) { > + ret = of_graph_parse_endpoint(ep_node, &ep); > + if (ret) { > + of_node_put(ep_node); > + return ret; > + } > + > + /* skip dsi input port, port == 0 is input port */ > + if (ep.port == 0) > + continue; > + > + /* parse bridge endpoint */ > + if (client == OUT_HDMI) { > + if (ep.id == 0) { > + ret = dsi_parse_bridge_endpoint(dsi, ep_node); > + if (dsi->bridge) > + break; > + } > + } else { /* parse panel endpoint */ > + if (ep.id > 0) { > + ret = dsi_parse_panel_endpoint(dsi, ep_node); > + if (dsi->panel) > + break; > + } > + } > + > + if (ret) { > + of_node_put(ep_node); > + return ret; > + } > + } > + > + if (!dsi->bridge && !dsi->panel) { > + DRM_ERROR("at least one bridge or panel node is required\n"); > + return -ENODEV; > + } > + > + return 0; > +} > + > +static int dsi_parse_dt(struct platform_device *pdev, struct dw_dsi *dsi) > +{ > + struct dsi_hw_ctx *ctx = dsi->ctx; > + const char *compatible; > + int ret = 0; > + struct device_node *np = NULL; > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) > + compatible = "hisilicon,kirin970-dsi"; > + else > + compatible = "hisilicon,kirin960-dsi"; > + > + np = of_find_compatible_node(NULL, NULL, compatible); > + if (!np) { > + dev_err(&pdev->dev, "NOT FOUND device node %s!\n", compatible); > + return -ENXIO; > + } > + > + ctx->base = of_iomap(np, 0); > + if (!(ctx->base)) { > + dev_err(&pdev->dev, "failed to get dsi base resource.\n"); > + return -ENXIO; > + } > + > + ctx->peri_crg_base = of_iomap(np, 1); > + if (!(ctx->peri_crg_base)) { > + dev_err(&pdev->dev, "failed to get peri_crg_base resource.\n"); > + return -ENXIO; > + } > + > + if (ctx->g_dss_version_tag == FB_ACCEL_KIRIN970) { > + ctx->pctrl_base = of_iomap(np, 2); > + if (!(ctx->pctrl_base)) { > + dev_err(&pdev->dev, > + "failed to get dss pctrl_base resource.\n"); > + return -ENXIO; > + } > + } > + > + dsi->gpio_mux = devm_gpiod_get(&pdev->dev, "mux", GPIOD_OUT_HIGH); > + if (IS_ERR(dsi->gpio_mux)) > + return PTR_ERR(dsi->gpio_mux); > + > + /* set dsi default output to panel */ > + dsi->cur_client = OUT_PANEL; > + dsi->attached_client = dsi->cur_client; > + > + DRM_INFO("dsi cur_client is %d <0->hdmi;1->panel>\n", > + dsi->cur_client); > + /* dis-reset */ > + /* ip_reset_dis_dsi0, ip_reset_dis_dsi1 */ > + writel(0x30000000, ctx->peri_crg_base + PERRSTDIS3); > + > + ctx->dss_dphy0_ref_clk = devm_clk_get(&pdev->dev, "clk_txdphy0_ref"); > + if (IS_ERR(ctx->dss_dphy0_ref_clk)) { > + dev_err(&pdev->dev, "failed to get dss_dphy0_ref_clk clock\n"); > + return PTR_ERR(ctx->dss_dphy0_ref_clk); > + } > + > + ret = clk_set_rate(ctx->dss_dphy0_ref_clk, DEFAULT_MIPI_CLK_RATE); > + if (ret < 0) { > + dev_err(&pdev->dev, "dss_dphy0_ref_clk clk_set_rate(%lu) failed, error=%d!\n", > + DEFAULT_MIPI_CLK_RATE, ret); > + return -EINVAL; > + } > + > + DRM_DEBUG("dss_dphy0_ref_clk:[%lu]->[%lu].\n", > + DEFAULT_MIPI_CLK_RATE, clk_get_rate(ctx->dss_dphy0_ref_clk)); > + > + ctx->dss_dphy0_cfg_clk = devm_clk_get(&pdev->dev, "clk_txdphy0_cfg"); > + if (IS_ERR(ctx->dss_dphy0_cfg_clk)) { > + dev_err(&pdev->dev, "failed to get dss_dphy0_cfg_clk clock\n"); > + return PTR_ERR(ctx->dss_dphy0_cfg_clk); > + } > + > + ret = clk_set_rate(ctx->dss_dphy0_cfg_clk, DEFAULT_MIPI_CLK_RATE); > + if (ret < 0) { > + dev_err(&pdev->dev, "dss_dphy0_cfg_clk clk_set_rate(%lu) failed, error=%d!\n", > + DEFAULT_MIPI_CLK_RATE, ret); > + return -EINVAL; > + } > + > + DRM_DEBUG("dss_dphy0_cfg_clk:[%lu]->[%lu].\n", > + DEFAULT_MIPI_CLK_RATE, clk_get_rate(ctx->dss_dphy0_cfg_clk)); > + > + ctx->dss_pclk_dsi0_clk = devm_clk_get(&pdev->dev, "pclk_dsi0"); > + if (IS_ERR(ctx->dss_pclk_dsi0_clk)) { > + dev_err(&pdev->dev, "failed to get dss_pclk_dsi0_clk clock\n"); > + return PTR_ERR(ctx->dss_pclk_dsi0_clk); > + } > + > + return 0; > +} > + > +static int dsi_probe(struct platform_device *pdev) > +{ > + struct device_node *np = pdev->dev.of_node; > + struct device *dev = &pdev->dev; > + struct dsi_data *data; > + struct dw_dsi *dsi; > + struct dsi_hw_ctx *ctx; > + int ret; > + > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); > + if (!data) { > + dev_err(&pdev->dev, "failed to allocate dsi data.\n"); > + return -ENOMEM; > + } > + dsi = &data->dsi; > + ctx = &data->ctx; > + dsi->ctx = ctx; > + > + ctx->g_dss_version_tag = (long)of_device_get_match_data(dev); > + > + /* parse HDMI bridge endpoint */ > + ret = dsi_parse_endpoint(dsi, np, OUT_HDMI); > + if (ret) > + return ret; > + > + ret = dsi_host_init(dev, dsi); > + if (ret) > + return ret; > + > + /* parse panel endpoint */ > + ret = dsi_parse_endpoint(dsi, np, OUT_PANEL); > + if (ret) > + goto err_host_unregister; > + > + ret = dsi_parse_dt(pdev, dsi); > + if (ret) > + goto err_host_unregister; > + > + platform_set_drvdata(pdev, data); > + > + ret = component_add(dev, &dsi_ops); > + if (ret) > + goto err_host_unregister; > + > + return 0; > + > +err_host_unregister: > + mipi_dsi_host_unregister(&dsi->host); > + return ret; > +} > + > +static int dsi_remove(struct platform_device *pdev) > +{ > + component_del(&pdev->dev, &dsi_ops); > + > + return 0; > +} > + > +static const struct of_device_id dsi_of_match[] = { > + { > + .compatible = "hisilicon,kirin960-dsi", > + .data = (void *)FB_ACCEL_HI366x > + }, { > + .compatible = "hisilicon,kirin970-dsi", > + .data = (void *)FB_ACCEL_KIRIN970 > + }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, dsi_of_match); > + > +static struct platform_driver dsi_driver = { > + .probe = dsi_probe, > + .remove = dsi_remove, > + .driver = { > + .name = "kirin9xx-dw-dsi", > + .of_match_table = dsi_of_match, > + }, > +}; > + > +module_platform_driver(dsi_driver); > + > +MODULE_DESCRIPTION("DesignWare MIPI DSI Host Controller v1.02 driver"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/staging/hikey9xx/gpu/kirin9xx_dw_dsi_reg.h b/drivers/staging/hikey9xx/gpu/kirin9xx_dw_dsi_reg.h > new file mode 100644 > index 000000000000..0e3971ca328c > --- /dev/null > +++ b/drivers/staging/hikey9xx/gpu/kirin9xx_dw_dsi_reg.h > @@ -0,0 +1,142 @@ > +/* SPDX-License-Identifier: GPL-2.0 */ > +/* > + * Copyright (c) 2016 Linaro Limited. > + * Copyright (c) 2014-2016 Hisilicon Limited. > + * Copyright (c) 2014-2020, Huawei Technologies Co., Ltd > + */ > + > +#ifndef __DW_DSI_REG_H__ > +#define __DW_DSI_REG_H__ > + > +#define MASK(x) (BIT(x) - 1) Not used, delete. > +#define DEFAULT_MAX_TX_ESC_CLK (10 * 1000000UL) > +/* > + * regs > + */ > +#define PWR_UP 0x04 /* Core power-up */ > +#define RESET 0 > +#define POWERUP BIT(0) > +#define PHY_IF_CFG 0xA4 /* D-PHY interface configuration */ > +#define CLKMGR_CFG 0x08 /* the internal clock dividers */ > +#define PHY_RSTZ 0xA0 /* D-PHY reset control */ > +#define PHY_ENABLECLK BIT(2) > +#define PHY_UNRSTZ BIT(1) > +#define PHY_UNSHUTDOWNZ BIT(0) > +#define PHY_TST_CTRL0 0xB4 /* D-PHY test interface control 0 */ > +#define PHY_TST_CTRL1 0xB8 /* D-PHY test interface control 1 */ > +#define CLK_TLPX 0x10 > +#define CLK_THS_PREPARE 0x11 > +#define CLK_THS_ZERO 0x12 > +#define CLK_THS_TRAIL 0x13 > +#define CLK_TWAKEUP 0x14 > +#define DATA_TLPX(x) (0x20 + ((x) << 4)) > +#define DATA_THS_PREPARE(x) (0x21 + ((x) << 4)) > +#define DATA_THS_ZERO(x) (0x22 + ((x) << 4)) > +#define DATA_THS_TRAIL(x) (0x23 + ((x) << 4)) > +#define DATA_TTA_GO(x) (0x24 + ((x) << 4)) > +#define DATA_TTA_GET(x) (0x25 + ((x) << 4)) > +#define DATA_TWAKEUP(x) (0x26 + ((x) << 4)) > +#define PHY_CFG_I 0x60 > +#define PHY_CFG_PLL_I 0x63 > +#define PHY_CFG_PLL_II 0x64 > +#define PHY_CFG_PLL_III 0x65 > +#define PHY_CFG_PLL_IV 0x66 > +#define PHY_CFG_PLL_V 0x67 > +#define DPI_COLOR_CODING 0x10 /* DPI color coding */ > +#define DPI_CFG_POL 0x14 /* DPI polarity configuration */ > +#define VID_HSA_TIME 0x48 /* Horizontal Sync Active time */ > +#define VID_HBP_TIME 0x4C /* Horizontal Back Porch time */ > +#define VID_HLINE_TIME 0x50 /* Line time */ > +#define VID_VSA_LINES 0x54 /* Vertical Sync Active period */ > +#define VID_VBP_LINES 0x58 /* Vertical Back Porch period */ > +#define VID_VFP_LINES 0x5C /* Vertical Front Porch period */ > +#define VID_VACTIVE_LINES 0x60 /* Vertical resolution */ > +#define VID_PKT_SIZE 0x3C /* Video packet size */ > +#define VID_MODE_CFG 0x38 /* Video mode configuration */ > +#define GEN_HDR 0x6c > +#define GEN_HDATA(data) (((data) & 0xffff) << 8) > +#define GEN_HDATA_MASK (0xffff << 8) > +#define GEN_HTYPE(type) (((type) & 0xff) << 0) > +#define GEN_HTYPE_MASK 0xff > +#define GEN_PLD_DATA 0x70 > +#define CMD_PKT_STATUS 0x74 > +#define GEN_CMD_EMPTY BIT(0) > +#define GEN_CMD_FULL BIT(1) > +#define GEN_PLD_W_EMPTY BIT(2) > +#define GEN_PLD_W_FULL BIT(3) > +#define GEN_PLD_R_EMPTY BIT(4) > +#define GEN_PLD_R_FULL BIT(5) > +#define GEN_RD_CMD_BUSY BIT(6) > +#define CMD_MODE_CFG 0x68 > +#define MAX_RD_PKT_SIZE_LP BIT(24) > +#define DCS_LW_TX_LP BIT(19) > +#define DCS_SR_0P_TX_LP BIT(18) > +#define DCS_SW_1P_TX_LP BIT(17) > +#define DCS_SW_0P_TX_LP BIT(16) > +#define GEN_LW_TX_LP BIT(14) > +#define GEN_SR_2P_TX_LP BIT(13) > +#define GEN_SR_1P_TX_LP BIT(12) > +#define GEN_SR_0P_TX_LP BIT(11) > +#define GEN_SW_2P_TX_LP BIT(10) > +#define GEN_SW_1P_TX_LP BIT(9) > +#define GEN_SW_0P_TX_LP BIT(8) > +#define EN_ACK_RQST BIT(1) > +#define EN_TEAR_FX BIT(0) > +#define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \ > + DCS_LW_TX_LP | \ > + DCS_SR_0P_TX_LP | \ > + DCS_SW_1P_TX_LP | \ > + DCS_SW_0P_TX_LP | \ > + GEN_LW_TX_LP | \ > + GEN_SR_2P_TX_LP | \ > + GEN_SR_1P_TX_LP | \ > + GEN_SR_0P_TX_LP | \ > + GEN_SW_2P_TX_LP | \ > + GEN_SW_1P_TX_LP | \ > + GEN_SW_0P_TX_LP) > +#define PHY_TMR_CFG 0x9C /* Data lanes timing configuration */ > +#define BTA_TO_CNT 0x8C /* Response timeout definition */ > +#define PHY_TMR_LPCLK_CFG 0x98 /* clock lane timing configuration */ > +#define CLK_DATA_TMR_CFG 0xCC > +#define LPCLK_CTRL 0x94 /* Low-power in clock lane */ > +#define PHY_TXREQUESTCLKHS BIT(0) > +#define MODE_CFG 0x34 /* Video or Command mode selection */ > +#define PHY_STATUS 0xB0 /* D-PHY PPI status interface */ > + > +#define PHY_STOP_WAIT_TIME 0x30 > +#define CMD_PKT_STATUS_TIMEOUT_US 20000 > + > +/* > + * regs relevant enum > + */ > +enum dpi_color_coding { > + DSI_24BITS_1 = 5, > +}; > + > +enum dsi_video_mode_type { > + DSI_NON_BURST_SYNC_PULSES = 0, > + DSI_NON_BURST_SYNC_EVENTS, > + DSI_BURST_SYNC_PULSES_1, > + DSI_BURST_SYNC_PULSES_2 > +}; > + > +enum dsi_work_mode { > + DSI_VIDEO_MODE = 0, > + DSI_COMMAND_MODE > +}; > + > +/* > + * Register Write/Read Helper functions > + */ > +static inline void dw_update_bits(void __iomem *addr, u32 bit_start, > + u32 mask, u32 val) Not used I think, so delete if not. > +{ > + u32 tmp, orig; > + > + orig = readl(addr); > + tmp = orig & ~(mask << bit_start); > + tmp |= (val & mask) << bit_start; > + writel(tmp, addr); > +} > + > +#endif /* __DW_DRM_DSI_H__ */ _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
