There's a warning message about an unused code. The code that
were using it were commented out, due to a problem causing the
firmware load to fail on the machines we're using for testing.
Change the place where we're commenting the code out, in order
to avoid the warning.
Fixes: 95d1f398c4dc ("media: atomisp: keep the ISP powered on when setting it")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
.../staging/media/atomisp/pci/atomisp_v4l2.c | 18 ++++++++++++------
1 file changed, 12 insertions(+), 6 deletions(-)
diff --git a/drivers/staging/media/atomisp/pci/atomisp_v4l2.c b/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
index b30a2e54067c..c89d477a3948 100644
--- a/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
+++ b/drivers/staging/media/atomisp/pci/atomisp_v4l2.c
@@ -734,6 +734,10 @@ static int atomisp_mrfld_pre_power_down(struct atomisp_device *isp)
* WA for DDR DVFS enable/disable
* By default, ISP will force DDR DVFS 1600MHz before disable DVFS
*/
+
+#if 0
+// Used only by atomisp_mrfld_power
+
static void punit_ddr_dvfs_enable(bool enable)
{
int door_bell = 1 << 8;
@@ -758,9 +762,12 @@ static void punit_ddr_dvfs_enable(bool enable)
if (max_wait == -1)
pr_info("DDR DVFS, door bell is not cleared within 3ms\n");
}
+#endif
static int atomisp_mrfld_power(struct atomisp_device *isp, bool enable)
{
+// FIXME: at least with ISP2401, the code below causes the driver to break
+#if 0
unsigned long timeout;
u32 val = enable ? MRFLD_ISPSSPM0_IUNIT_POWER_ON :
MRFLD_ISPSSPM0_IUNIT_POWER_OFF;
@@ -817,22 +824,21 @@ static int atomisp_mrfld_power(struct atomisp_device *isp, bool enable)
dev_err(isp->dev, "IUNIT power-%s timeout.\n", enable ? "on" : "off");
return -EBUSY;
+#else
+ return 0;
+#endif
}
/* Workaround for pmu_nc_set_power_state not ready in MRFLD */
int atomisp_mrfld_power_down(struct atomisp_device *isp)
{
- return 0;
-// FIXME: at least with ISP2401, the code below causes the driver to break
-// return atomisp_mrfld_power(isp, false);
+ return atomisp_mrfld_power(isp, false);
}
/* Workaround for pmu_nc_set_power_state not ready in MRFLD */
int atomisp_mrfld_power_up(struct atomisp_device *isp)
{
- return 0;
-// FIXME: at least with ISP2401, the code below causes the driver to break
-// return atomisp_mrfld_power(isp, true);
+ return atomisp_mrfld_power(isp, true);
}
int atomisp_runtime_suspend(struct device *dev)
--
2.26.2
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
