Hi Sergio,
On 20/3/20 2:14 am, Sergio Paracuellos wrote:
In some platforms gpio's are not used for reset but
for other purposes. Because of that when we try to
get them are valid gpio's but are already assigned
to do other function. To avoid those kind of problems
in those platforms just notice the fail in the kernel
but continue doing normal boot.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@xxxxxxxxx>
---
drivers/staging/mt7621-pci/pci-mt7621.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/drivers/staging/mt7621-pci/pci-mt7621.c b/drivers/staging/mt7621-pci/pci-mt7621.c
index 2a01645162a5..d6fc8a08c9bd 100644
--- a/drivers/staging/mt7621-pci/pci-mt7621.c
+++ b/drivers/staging/mt7621-pci/pci-mt7621.c
@@ -363,10 +363,8 @@ static int mt7621_pcie_parse_port(struct mt7621_pcie *pcie,
port->gpio_rst = devm_gpiod_get_index_optional(dev, "reset", slot,
GPIOD_OUT_LOW);
- if (IS_ERR(port->gpio_rst)) {
- dev_err(dev, "Failed to get GPIO for PCIe%d\n", slot);
- return PTR_ERR(port->gpio_rst);
- }
+ if (IS_ERR(port->gpio_rst))
+ dev_notice(dev, "Failed to get GPIO for PCIe%d\n", slot);
port->slot = slot;
port->pcie = pcie;
Even with this fix in place I still get a dump on boot:
...
rt2880-pinmux pinctrl: pcie is already enabled
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
mt7621-pci 1e140000.pcie: Failed to get GPIO for PCIe1
mt7621-pci 1e140000.pcie: Failed to get GPIO for PCIe2
gpiod_set_value: invalid GPIO (errorpointer)
gpiod_set_value: invalid GPIO (errorpointer)
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
gpiod_set_value: invalid GPIO (errorpointer)
gpiod_set_value: invalid GPIO (errorpointer)
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: PCIE0 enabled
mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xffffffff]
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
pci 0000:00:00.0: supports D1
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x601fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
pci 0000:00:00.0: BAR 7: no space for [io size 0x1000]
pci 0000:00:00.0: BAR 7: failed to assign [io size 0x1000]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x601fffff 64bit]
pci 0000:01:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff]
pci 0000:00:00.0: bridge window [mem 0x60200000-0x602fffff pref]
pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
pcieport 0000:00:00.0: enabling device (0004 -> 0006)
CPU 1 Unable to handle kernel paging request at virtual address fffffff0, epc == 8039c7b0, ra == 804fe0a0
Oops[#1]:
CPU: 1 PID: 103 Comm: kworker/1:1 Not tainted 5.6.0-rc3-00180-gc15e7f072288-dirty #5
Workqueue: events deferred_probe_work_func
$ 0 : 00000000 00000001 82051e84 00000001
$ 4 : fffffff0 00000001 00000000 803a0000
$ 8 : 00000024 ffffffff 00000001 302e3030
$12 : 00000000 8fd6dbd8 ffffffff 00000020
$16 : 82051e80 820d4250 00000000 8fd6dcd0
$20 : 820d41e0 809a0000 820d4228 8fd47e10
$24 : 00000000 00000020
$28 : 8fd6c000 8fd6dc70 8fd6dcf8 804fe0a0
Hi : 00000125
Lo : 122f2000
epc : 8039c7b0 gpiod_free+0x14/0x6c
ra : 804fe0a0 mt7621_pci_probe+0x678/0xc68
Status: 1100fc03 KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : fffffff0
PrId : 0001992f (MIPS 1004Kc)
Modules linked in:
Process kworker/1:1 (pid: 103, threadinfo=(ptrval), task=(ptrval), tls=00000000)
Stack : 820d4250 809e2aa0 82051880 820d4250 82051e80 804fe0a0 1e160000 00000001
60000000 00000000 f0000002 00000000 00000000 809a0000 8fd47e10 808d63d4
80930000 808d6260 808d0000 808d61fc 808c0000 8fd47e10 808d6208 808d0000
8fd6dcd0 8fd6dcd0 809e2aa0 809db510 809db510 00000006 00000001 00000000
00000000 00000000 01000000 1e1440ff 00000000 00000000 1e160000 00000000
...
Call Trace:
[<8039c7b0>] gpiod_free+0x14/0x6c
[<804fe0a0>] mt7621_pci_probe+0x678/0xc68
[<80402ab8>] platform_drv_probe+0x40/0x94
[<80400a74>] really_probe+0x104/0x364
[<803feb74>] bus_for_each_drv+0x84/0xdc
[<80400924>] __device_attach+0xdc/0x120
[<803ffb5c>] bus_probe_device+0xa0/0xbc
[<80400124>] deferred_probe_work_func+0x7c/0xbc
[<800420e8>] process_one_work+0x230/0x450
[<80042638>] worker_thread+0x330/0x5fc
[<80048eb0>] kthread+0x12c/0x134
[<80007438>] ret_from_kernel_thread+0x14/0x1c
Code: 27bdffe8 afb00010 afbf0014 <8c830000> 10600005 00808025 0c0e6efb 00000000 14400007
---[ end trace b050393bd02cbb28 ]---
If however I remove the gpio 7 and 8 reset entries from the devicetree then I can boot up.
I see two cases on boot, one successfully probes the PCI bus, and seems to work:
...
rt2880-pinmux pinctrl: pcie is already enabled
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: PCIE0 enabled
mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xffffffff]
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
pci 0000:00:00.0: supports D1
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref]
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x601fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
pci 0000:00:00.0: BAR 7: no space for [io size 0x1000]
pci 0000:00:00.0: BAR 7: failed to assign [io size 0x1000]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x601fffff 64bit]
pci 0000:01:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff]
pci 0000:00:00.0: bridge window [mem 0x60200000-0x602fffff pref]
pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
pcieport 0000:00:00.0: enabling device (0004 -> 0006)
...
The other case does not probe successfully (but still boots up all the way):
...
rt2880-pinmux pinctrl: pcie is already enabled
mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
mt7621-pci 1e140000.pcie: Nothing is connected in virtual bridges. Exiting..
...
It is probably 50:50 on any boot whether it will probe pci successfully or
fail to probe it.
BTW, this is with the patch here applied:
http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2020-March/142472.html
Regards
Greg
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
