Hi Greg,
On Tue, Jun 25, 2019 at 7:18 AM Sergio Paracuellos
<sergio.paracuellos@xxxxxxxxx> wrote:
>
> Hi Greg,
>
> On Tue, Jun 25, 2019 at 7:10 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> >
> > Hi Sergio,
> >
> > On 23/6/19 3:58 pm, Sergio Paracuellos wrote:
> > > On Sun, Jun 23, 2019 at 4:15 AM Brett Neumeier <bneumeier@xxxxxxxxx> wrote:
> > >> On Fri, Jun 21, 2019 at 7:35 AM Greg Ungerer <gerg@xxxxxxxxxx> wrote:
> > >>> On 21/6/19 4:15 pm, Sergio Paracuellos wrote:
> > >>>> This patch series properly handle minor issues in this driver. These are:
> > >>>> * Disable pcie port clock on pci dirver instead of doing it in the phy
> > >>>> driver. The pci driver is the correct place to do this.
> > >>>> * Add a missing call to phy_exit function to properly handle the function
> > >>>> 'mt7621_pcie_init_port' error path.
> > >>>> * Move driver to init in a later stage using 'module_init' instead of using
> > >>>> 'arch_initcall'.
> > >>>>
> > >>>> Patches are only compile-tested. It would be awasome to be tested before applied
> > >>>> them (mainly the change to 'module_init' stuff).
> > >>
> > >> I have similar results to Greg -- on GnuBee PC1 and PC2, six boot
> > >> attempts each on a kernel built from staging-next, I have four hangs
> > >> and eight successful boots. The hanging patterns are similar to
> > >> previous results. If the full boot logs would be helpful let me know,
> > >> I can provide them.
> > >
> > > Thanks for letting me know. One thing we can try is check init order
> > > in v4.20 kernel. Can you please try to compile pci driver for the
> > > kernel v4.20 tag changing
> > > driver's last line 'arch_initcall' into 'module_init'? Just to know if
> > > at that working driver putting all the stuff in a later stage stills
> > > work as expected.
> > >
> > > Full dmesg's of this v4.20 wih the change would be helpful.
> >
> > Not exactly what you asked for, but just as useful I think.
> > I have a linux-5.1.14 kernel with the linux-4.20 pci-mt7621.c
> > driver in place. That works great, never hangs, always probes
> > PCI and works.
> >
> > If I change the pci-mt7621.c arch_initcall() to module_init(),
> > then I see the PCI probe happen much latter in boot. Running this
> > I have booted about 15 times, no hangs, PCI bus probed and working
> > on every boot.
>
> Perfect. That is exactly what I wanted to know. Thanks for testing this.
>
> >
> > Boot log below.
> >
> > Regards
> > Greg
Can you please test the following change?
diff --git a/drivers/staging/mt7621-pci/pci-mt7621.c
b/drivers/staging/mt7621-pci/pci-mt7621.c
index a981f4f0ed03..9ae14f722c91 100644
--- a/drivers/staging/mt7621-pci/pci-mt7621.c
+++ b/drivers/staging/mt7621-pci/pci-mt7621.c
@@ -41,8 +41,8 @@
/* MediaTek specific configuration registers */
#define PCIE_FTS_NUM 0x70c
-#define PCIE_FTS_NUM_MASK GENMASK(15, 8)
-#define PCIE_FTS_NUM_L0(x) ((x) & 0xff << 8)
+#define PCIE_FTS_NUM_MASK GENMASK(7, 0)
+#define PCIE_FTS_NUM_L0(x) ((x) << 8)
/* rt_sysc_membase relative registers */
#define RALINK_CLKCFG1 0x30
@@ -540,7 +540,7 @@ static void mt7621_pcie_enable_ports(struct
mt7621_pcie *pcie)
write_config(pcie, slot, PCI_COMMAND, val);
/* configure RC FTS number to 250 when it leaves L0s */
val = read_config(pcie, slot, PCIE_FTS_NUM);
- val &= ~PCIE_FTS_NUM_MASK;
+ val &= ~(PCIE_FTS_NUM_MASK) << 8;
val |= PCIE_FTS_NUM_L0(0x50);
write_config(pcie, slot, PCIE_FTS_NUM, val);
}
Best regards,
Sergio Paracuellos
> >
> > Linux version 5.1.14 (gerg@goober) (gcc version 5.4.0 (GCC)) #2 SMP Tue Jun 25 14:34:27 AEST 2019
> > SoC Type: MediaTek MT7621 ver:1 eco:3
> > printk: bootconsole [early0] enabled
> > CPU0 revision is: 0001992f (MIPS 1004Kc)
> > OF: fdt: No chosen node found, continuing without
> > MIPS: machine is Digi EX15
> > Determined physical RAM map:
> > memory: 10000000 @ 00000000 (usable)
> > Initrd not found or empty - disabling initrd
> > VPE topology {2,2} total 4
> > Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> > Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> > MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> > Zone ranges:
> > Normal [mem 0x0000000000000000-0x000000000fffffff]
> > Movable zone start for each node
> > Early memory node ranges
> > node 0: [mem 0x0000000000000000-0x000000000fffffff]
> > Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
> > random: get_random_bytes called from start_kernel+0xb0/0x51c with crng_init=0
> > percpu: Embedded 15 pages/cpu s30144 r8192 d23104 u61440
> > Built 1 zonelists, mobility grouping on. Total pages: 65024
> > Kernel command line: console=ttyS0,115200 ubi.mtd=3 root=/dev/mtdblock5 bootpart=a
> > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> > Writing ErrCtl register=00030517
> > Readback ErrCtl register=00030517
> > Memory: 251176K/262144K available (6464K kernel code, 243K rwdata, 1200K rodata, 272K init, 228K bss, 10968K reserved, 0K cma-reserved)
> > SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
> > rcu: Hierarchical RCU implementation.
> > rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> > NR_IRQS: 256
> > clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
> > sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
> > Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
> > pid_max: default: 32768 minimum: 301
> > Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> > Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> > rcu: Hierarchical SRCU implementation.
> > smp: Bringing up secondary CPUs ...
> > Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> > Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> > MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> > CPU1 revision is: 0001992f (MIPS 1004Kc)
> > Synchronize counters for CPU 1: done.
> > Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> > Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> > MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> > CPU2 revision is: 0001992f (MIPS 1004Kc)
> > Synchronize counters for CPU 2: done.
> > Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
> > Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> > MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> > CPU3 revision is: 0001992f (MIPS 1004Kc)
> > Synchronize counters for CPU 3: done.
> > smp: Brought up 1 node, 4 CPUs
> > devtmpfs: initialized
> > clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> > futex hash table entries: 1024 (order: 3, 32768 bytes)
> > pinctrl core: initialized pinctrl subsystem
> > NET: Registered protocol family 16
> > SCSI subsystem initialized
> > usbcore: registered new interface driver usbfs
> > usbcore: registered new interface driver hub
> > usbcore: registered new device driver usb
> > pcf857x 0-0026: probed
> > i2c-mt7621 1e000900.i2c: clock 400KHz, re-start not support
> > clocksource: Switched to clocksource GIC
> > NET: Registered protocol family 2
> > tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
> > TCP established hash table entries: 2048 (order: 1, 8192 bytes)
> > TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
> > TCP: Hash tables configured (established 2048 bind 2048)
> > UDP hash table entries: 256 (order: 1, 8192 bytes)
> > UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
> > NET: Registered protocol family 1
> > workingset: timestamp_bits=30 max_order=16 bucket_order=0
> > squashfs: version 4.0 (2009/01/31) Phillip Lougher
> > random: fast init done
> > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
> > mt7621_gpio 1e000600.gpio: registering 32 gpios
> > mt7621_gpio 1e000600.gpio: registering 32 gpios
> > mt7621_gpio 1e000600.gpio: registering 32 gpios
> > Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
> > printk: console [ttyS0] disabled
> > 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
> > printk: console [ttyS0] enabled
> > printk: console [ttyS0] enabled
> > printk: bootconsole [early0] disabled
> > printk: bootconsole [early0] disabled
> > 1e000d00.uartlite: ttyS1 at MMIO 0x1e000d00 (irq = 19, base_baud = 3125000) is a 16550A
> > cacheinfo: Failed to find cpu0 device node
> > cacheinfo: Unable to detect cache hierarchy for CPU 0
> > brd: module loaded
> > mt7621-nand: NAND register bank at 0xbe003000
> > mt7621-nand: NAND ECC register bank at 0xbe003800
> > nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
> > nand: Micron NAND 512MiB 3,3V 8-bit
> > nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> > nand: ecc bit: 4, spare_per_sector: 16
> > Bad block table found at page 262080, version 0x01
> > Bad block table found at page 262016, version 0x01
> > 5 fixed-partitions partitions found on MTD device MT7621-NAND
> > Creating 5 MTD partitions on "MT7621-NAND":
> > 0x000000000000-0x000000200000 : "u-boot"
> > 0x000000200000-0x000000300000 : "u-boot-env"
> > 0x000000300000-0x000000500000 : "log"
> > 0x000000500000-0x000020000000 : "flash"
> > 0x000000000000-0x000020000000 : "all"
> > libphy: Fixed MDIO Bus: probed
> > tun: Universal TUN/TAP device driver, 1.6
> > libphy: mdio: probed
> > mtk_soc_eth 1e100000.ethernet: generated random MAC address c6:f5:21:ba:39:d3
> > mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
> > mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
> > PPP generic driver version 2.4.2
> > PPP BSD Compression module registered
> > PPP Deflate Compression module registered
> > PPP MPPE Compression module registered
> > NET: Registered protocol family 24
> > SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
> > CSLIP: code copyright 1989 Regents of the University of California.
> > usbcore: registered new interface driver asix
> > usbcore: registered new interface driver ax88179_178a
> > usbcore: registered new interface driver cdc_ether
> > usbcore: registered new interface driver cdc_eem
> > usbcore: registered new interface driver rndis_host
> > usbcore: registered new interface driver cdc_subset
> > usbcore: registered new interface driver cdc_ncm
> > usbcore: registered new interface driver qmi_wwan
> > usbcore: registered new interface driver cdc_mbim
> > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> > ehci-pci: EHCI PCI platform driver
> > ehci-platform: EHCI generic platform driver
> > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> > ohci-pci: OHCI PCI platform driver
> > xhci-mtk 1e1c0000.xhci: xHCI Host Controller
> > xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
> > xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
> > xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
> > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
> > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> > usb usb1: Product: xHCI Host Controller
> > usb usb1: Manufacturer: Linux 5.1.14-ac0 xhci-hcd
> > usb usb1: SerialNumber: 1e1c0000.xhci
> > hub 1-0:1.0: USB hub found
> > hub 1-0:1.0: 2 ports detected
> > xhci-mtk 1e1c0000.xhci: xHCI Host Controller
> > xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
> > xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
> > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
> > usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01
> > usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> > usb usb2: Product: xHCI Host Controller
> > usb usb2: Manufacturer: Linux 5.1.14-ac0 xhci-hcd
> > usb usb2: SerialNumber: 1e1c0000.xhci
> > hub 2-0:1.0: USB hub found
> > hub 2-0:1.0: 1 port detected
> > usbcore: registered new interface driver cdc_acm
> > cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
> > usbcore: registered new interface driver cdc_wdm
> > usbcore: registered new interface driver usb-storage
> > usbcore: registered new interface driver usbserial_generic
> > usbserial: USB Serial support registered for generic
> > usbcore: registered new interface driver ipw
> > usbserial: USB Serial support registered for IPWireless converter
> > usbcore: registered new interface driver option
> > usbserial: USB Serial support registered for GSM modem (1-port)
> > usbcore: registered new interface driver qcaux
> > usbserial: USB Serial support registered for qcaux
> > usbcore: registered new interface driver qcserial
> > usbserial: USB Serial support registered for Qualcomm USB modem
> > usbcore: registered new interface driver quatech2
> > usbserial: USB Serial support registered for Quatech 2nd gen USB to Serial Driver
> > usbcore: registered new interface driver usb_serial_simple
> > usbserial: USB Serial support registered for carelink
> > usbserial: USB Serial support registered for zio
> > usbserial: USB Serial support registered for funsoft
> > usbserial: USB Serial support registered for flashloader
> > usbserial: USB Serial support registered for google
> > usbserial: USB Serial support registered for libtransistor
> > usbserial: USB Serial support registered for vivopay
> > usbserial: USB Serial support registered for moto_modem
> > usbserial: USB Serial support registered for motorola_tetra
> > usbserial: USB Serial support registered for novatel_gps
> > usbserial: USB Serial support registered for hp4x
> > usbserial: USB Serial support registered for suunto
> > usbserial: USB Serial support registered for siemens_mpi
> > ***** Xtal 40MHz *****
> > PCIE1 no card, disable it(RST&CLK)
> > PCIE2 no card, disable it(RST&CLK)
> > PCIE0 enabled
> > PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
> > mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
> > pci_bus 0000:00: root bus resource [io 0xffffffff]
> > pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
> > pci_bus 0000:00: root bus resource [bus 00-ff]
> > pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
> > pci 0000:00:00.0: PCI bridge to [bus 01-ff]
> > pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
> > pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
> > pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x601fffff]
> > pci 0000:00:00.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
> > pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
> > pci 0000:00:00.0: BAR 7: no space for [io size 0x1000]
> > pci 0000:00:00.0: BAR 7: failed to assign [io size 0x1000]
> > pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x601fffff 64bit]
> > pci 0000:01:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
> > pci 0000:00:00.0: PCI bridge to [bus 01]
> > pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff]
> > pci 0000:00:00.0: bridge window [mem 0x60200000-0x602fffff pref]
> > pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
> > pcieport 0000:00:00.0: enabling device (0004 -> 0006)
> > u32 classifier
> > input device check on
> > ipip: IPv4 and MPLS over IPv4 tunneling driver
> > gre: GRE over IPv4 demultiplexor driver
> > ip_gre: GRE over IPv4 tunneling driver
> > Initializing XFRM netlink socket
> > NET: Registered protocol family 10
> > Segment Routing with IPv6
> > sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
> > NET: Registered protocol family 17
> > NET: Registered protocol family 15
> > 8021q: 802.1Q VLAN Support v1.8
> > libphy: dsa slave smi: probed
> > mt7530 mdio-bus:00 lan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
> > mt7530 mdio-bus:00 wan (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
> > DSA: tree 0 setup
> > ubi0: attaching mtd3
> > ubi0: scanning is finished
> > ubi0: attached mtd3 (name "flash", size 507 MiB)
> > ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
> > ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
> > ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
> > ubi0: good PEBs: 4052, bad PEBs: 4, corrupted PEBs: 0
> > ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
> > ubi0: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 1236486005
> > ubi0: available PEBs: 0, total reserved PEBs: 4052, PEBs reserved for bad PEB handling: 76
> > ubi0: background thread "ubi_bgt0d" started, PID 112
> > hctosys: unable to open rtc device (rtc0)
> > VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
> > devtmpfs: mounted
> > Freeing unused kernel memory: 272K
> > This architecture does not have kernel memory protection.
> > Run /sbin/init as init process
> > Run /etc/init as init process
> > Run /bin/init as init process
> >
> >
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
