[PATCH 4/6] staging: kpc2000: add spaces around operators in cell_probe.c

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Fixes checkpatch.pl warning "spaces preferred around that <op>".

Signed-off-by: Simon Sandström <simon@xxxxxxxxxx>
---
 drivers/staging/kpc2000/kpc2000/cell_probe.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/staging/kpc2000/kpc2000/cell_probe.c b/drivers/staging/kpc2000/kpc2000/cell_probe.c
index 4742f909db79..9a32660a56e2 100644
--- a/drivers/staging/kpc2000/kpc2000/cell_probe.c
+++ b/drivers/staging/kpc2000/kpc2000/cell_probe.c
@@ -320,7 +320,7 @@ static int probe_core_uio(unsigned int core_num, struct kp2000_device *pcard,
 
 	kudev->uioinfo.mem[0].name = "uiomap";
 	kudev->uioinfo.mem[0].addr = pci_resource_start(pcard->pdev, REG_BAR) + cte.offset;
-	kudev->uioinfo.mem[0].size = (cte.length + PAGE_SIZE-1) & ~(PAGE_SIZE-1); // Round up to nearest PAGE_SIZE boundary
+	kudev->uioinfo.mem[0].size = (cte.length + PAGE_SIZE - 1) & ~(PAGE_SIZE - 1); // Round up to nearest PAGE_SIZE boundary
 	kudev->uioinfo.mem[0].memtype = UIO_MEM_PHYS;
 
 	kudev->dev = device_create(kpc_uio_class, &pcard->pdev->dev, MKDEV(0,0), kudev, "%s.%d.%d.%d", kudev->uioinfo.name, pcard->card_num, cte.type, kudev->core_num);
@@ -399,7 +399,7 @@ static int  kp2000_setup_dma_controller(struct kp2000_device *pcard)
 	for (i = 0 ; i < 32 ; i++) {
 		capabilities_reg = readq( pcard->dma_bar_base + KPC_DMA_C2S_BASE_OFFSET + (KPC_DMA_ENGINE_SIZE * i) );
 		if (capabilities_reg & ENGINE_CAP_PRESENT_MASK) {
-			err = create_dma_engine_core(pcard, (KPC_DMA_C2S_BASE_OFFSET + (KPC_DMA_ENGINE_SIZE * i)), 32+i,  pcard->pdev->irq);
+			err = create_dma_engine_core(pcard, (KPC_DMA_C2S_BASE_OFFSET + (KPC_DMA_ENGINE_SIZE * i)), 32 + i,  pcard->pdev->irq);
 			if (err)
 				goto err_out;
 		}
@@ -481,7 +481,7 @@ int  kp2000_probe_cores(struct kp2000_device *pcard)
 	// Finally, instantiate a UIO device for the core_table.
 	cte.type                = 0; // CORE_ID_BOARD_INFO
 	cte.offset              = 0; // board info is always at the beginning
-	cte.length              = 512*8;
+	cte.length              = 512 * 8;
 	cte.s2c_dma_present     = false;
 	cte.s2c_dma_channel_num = 0;
 	cte.c2s_dma_present     = false;
-- 
2.20.1

_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel




[Index of Archives]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux