On Fri, Jan 11, 2019 at 09:48:21AM +0100, Johan Hovold wrote:
> On Thu, Jan 10, 2019 at 11:23:07PM +0530, Nishad Kamdar wrote:
> > Use the gpiod interface instead of the deprecated old non-descriptor
> > interface while continuing to ignore gpio flags from device tree in
> > "svc_reset_onoff()" for now.
> >
> > Signed-off-by: Nishad Kamdar <nishadkamdar@xxxxxxxxx>
> > ---
> > Changes in v5:
> > - Change the commit message.
> > - Restore the names of the gpio device-tree properties without
> > the "-gpio" suffix.
> > Changes in v4:
> > - Move 'gpio_desc *svc_sysboot' below the reset flag
> > as it is more logical to have reset flag below
> > reset gpio.
> > - Remove a few unnecessary line breaks.
> > Changes in v3:
> > - Add this patch to a patchset.
> > Changes in v2:
> > - Move comment to the same line as to what it applies to.
> > ---
>
> Also looks good. Some really minor comments to a couple of the error
> messages. The issues are there in the current code, but since you modify
> these messages anyway you might as well fix them up. Please fix that and
> resend with my
>
> Reviewed-by: Johan Hovold <johan@xxxxxxxxxx>
>
Ok, I'll do that.
> Really good job with this!
>
Thank you.
> > @@ -435,6 +428,7 @@ static int arche_platform_probe(struct platform_device *pdev)
> > struct device *dev = &pdev->dev;
> > struct device_node *np = dev->of_node;
> > int ret;
> > + unsigned int flags;
> >
> > arche_pdata = devm_kzalloc(&pdev->dev, sizeof(*arche_pdata),
> > GFP_KERNEL);
> > @@ -444,61 +438,33 @@ static int arche_platform_probe(struct platform_device *pdev)
> > /* setup svc reset gpio */
> > arche_pdata->is_reset_act_hi = of_property_read_bool(np,
> > "svc,reset-active-high");
> > - arche_pdata->svc_reset_gpio = of_get_named_gpio(np,
> > - "svc,reset-gpio",
> > - 0);
> > - if (!gpio_is_valid(arche_pdata->svc_reset_gpio)) {
> > - dev_err(dev, "failed to get reset-gpio\n");
> > - return arche_pdata->svc_reset_gpio;
> > - }
> > - ret = devm_gpio_request(dev, arche_pdata->svc_reset_gpio, "svc-reset");
> > - if (ret) {
> > - dev_err(dev, "failed to request svc-reset gpio:%d\n", ret);
> > - return ret;
> > - }
> > - ret = gpio_direction_output(arche_pdata->svc_reset_gpio,
> > - arche_pdata->is_reset_act_hi);
> > - if (ret) {
> > - dev_err(dev, "failed to set svc-reset gpio dir:%d\n", ret);
> > + if (arche_pdata->is_reset_act_hi)
> > + flags = GPIOD_OUT_HIGH;
> > + else
> > + flags = GPIOD_OUT_LOW;
> > +
> > + arche_pdata->svc_reset = devm_gpiod_get(dev, "svc,reset", flags);
> > + if (IS_ERR(arche_pdata->svc_reset)) {
> > + ret = PTR_ERR(arche_pdata->svc_reset);
> > + dev_err(dev, "failed to request svc-reset GPIO:%d\n", ret);
>
> Add a space after ':' for consistency.
>
Ok. I'll do that.
> > @@ -515,19 +481,11 @@ static int arche_platform_probe(struct platform_device *pdev)
> > arche_pdata->num_apbs = of_get_child_count(np);
> > dev_dbg(dev, "Number of APB's available - %d\n", arche_pdata->num_apbs);
> >
> > - arche_pdata->wake_detect_gpio = of_get_named_gpio(np,
> > - "svc,wake-detect-gpio",
> > - 0);
> > - if (arche_pdata->wake_detect_gpio < 0) {
> > - dev_err(dev, "failed to get wake detect gpio\n");
> > - return arche_pdata->wake_detect_gpio;
> > - }
> > -
> > - ret = devm_gpio_request(dev, arche_pdata->wake_detect_gpio,
> > - "wake detect");
> > - if (ret) {
> > - dev_err(dev, "Failed requesting wake_detect gpio %d\n",
> > - arche_pdata->wake_detect_gpio);
> > + arche_pdata->wake_detect = devm_gpiod_get(dev, "svc,wake-detect",
> > + GPIOD_IN);
> > + if (IS_ERR(arche_pdata->wake_detect)) {
> > + ret = PTR_ERR(arche_pdata->wake_detect);
> > + dev_err(dev, "Failed requesting wake_detect GPIO %d\n", ret);
>
> Add colon after "GPIO" for consistency (and to avoid ambiguity).
>
Ok, I'll do that.
Thanks for the review,
Nishad
> > return ret;
> > }
>
> Thanks,
> Johan
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
