Fix some comment-related issues reported by checkpatch.pl:
- Block comments use * on subsequent lines
- Block comments use a trailing */ on a separate line
Signed-off-by: Jona Crasselt <jona.crasselt@xxxxxx>
Signed-off-by: Felix Windsheimer <felix.windsheimer@xxxxxx>
---
drivers/staging/mt7621-mmc/sd.c | 31 +++++++++++++++++--------------
1 file changed, 17 insertions(+), 14 deletions(-)
diff --git a/drivers/staging/mt7621-mmc/sd.c b/drivers/staging/mt7621-mmc/sd.c
index 7b66f9b0a094..e42cfe5fba7e 100644
--- a/drivers/staging/mt7621-mmc/sd.c
+++ b/drivers/staging/mt7621-mmc/sd.c
@@ -318,9 +318,9 @@ static void msdc_abort_data(struct msdc_host *host)
#ifdef CONFIG_PM
/*
- register as callback function of WIFI(combo_sdio_register_pm) .
- can called by msdc_drv_suspend/resume too.
-*/
+ * register as callback function of WIFI(combo_sdio_register_pm) .
+ * can called by msdc_drv_suspend/resume too.
+ */
static void msdc_pm(pm_message_t state, void *data)
{
struct msdc_host *host = (struct msdc_host *)data;
@@ -711,7 +711,8 @@ static int msdc_do_request(struct mmc_host *mmc, struct mmc_request *mrq)
goto done;
/* for read, the data coming too fast, then CRC error
- start DMA no business with CRC. */
+ * start DMA no business with CRC.
+ */
//init_completion(&host->xfer_done);
msdc_dma_start(host);
@@ -794,9 +795,10 @@ static int msdc_tune_cmdrsp(struct msdc_host *host, struct mmc_command *cmd)
u32 skip = 1;
/* ==== don't support 3.0 now ====
- 1: R_SMPL[1]
- 2: PAD_CMD_RESP_RXDLY[26:22]
- ==========================*/
+ * 1: R_SMPL[1]
+ * 2: PAD_CMD_RESP_RXDLY[26:22]
+ * ==========================
+ */
// save the previous tune result
sdr_get_field(host->base + MSDC_IOCON, MSDC_IOCON_RSPL, &orig_rsmpl);
@@ -1431,13 +1433,13 @@ static irqreturn_t msdc_irq(int irq, void *dev_id)
/* mmc irq interrupts */
if (intsts & MSDC_INT_MMCIRQ)
dev_info(mmc_dev(host->mmc), "msdc[%d] MMCIRQ: SDC_CSTS=0x%.8x\r\n",
- host->id, readl(host->base + SDC_CSTS));
+ host->id, readl(host->base + SDC_CSTS));
return IRQ_HANDLED;
}
/*--------------------------------------------------------------------------*/
-/* platform_driver members */
+/* platform_driver members */
/*--------------------------------------------------------------------------*/
/* called by msdc_drv_probe/remove */
static void msdc_enable_cd_irq(struct msdc_host *host, int enable)
@@ -1448,9 +1450,9 @@ static void msdc_enable_cd_irq(struct msdc_host *host, int enable)
if ((hw->flags & MSDC_CD_PIN_EN) == 0) {
/* Pull down card detection pin since it is not avaiable */
/*
- if (hw->config_gpio_pin)
- hw->config_gpio_pin(MSDC_CD_PIN, GPIO_PULL_DOWN);
- */
+ * if (hw->config_gpio_pin)
+ * hw->config_gpio_pin(MSDC_CD_PIN, GPIO_PULL_DOWN);
+ */
sdr_clr_bits(host->base + MSDC_PS, MSDC_PS_CDEN);
sdr_clr_bits(host->base + MSDC_INTEN, MSDC_INTEN_CDSC);
sdr_clr_bits(host->base + SDC_CFG, SDC_CFG_INSWKUP);
@@ -1538,8 +1540,9 @@ static void msdc_init_hw(struct msdc_host *host)
#endif
/* for safety, should clear SDC_CFG.SDIO_INT_DET_EN & set SDC_CFG.SDIO in
- pre-loader,uboot,kernel drivers. and SDC_CFG.SDIO_INT_DET_EN will be only
- set when kernel driver wants to use SDIO bus interrupt */
+ * pre-loader,uboot,kernel drivers. and SDC_CFG.SDIO_INT_DET_EN will be only
+ * set when kernel driver wants to use SDIO bus interrupt
+ */
/* Configure to enable SDIO mode. it's must otherwise sdio cmd5 failed */
sdr_set_bits(host->base + SDC_CFG, SDC_CFG_SDIO);
--
2.17.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
