On 11/22/2018 04:18 PM, Rui Miguel Silva wrote:
> Add bindings documentation for i.MX7 media drivers.
> The imx7 MIPI CSI2 and imx7 CMOS Sensor Interface.
>
> Signed-off-by: Rui Miguel Silva <rui.silva@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> Acked-by: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
Please move this patch to the beginning of the series to avoid
checkpatch warnings:
WARNING: DT compatible string "fsl,imx7-csi" appears un-documented -- check ./Documentation/devicetree/bindings/
#1378: FILE: drivers/staging/media/imx/imx7-media-csi.c:1336:
+ { .compatible = "fsl,imx7-csi" },
Thanks!
Hans
> ---
> .../devicetree/bindings/media/imx7-csi.txt | 45 ++++++++++
> .../bindings/media/imx7-mipi-csi2.txt | 90 +++++++++++++++++++
> 2 files changed, 135 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/imx7-csi.txt
> create mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
>
> diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt
> new file mode 100644
> index 000000000000..3c07bc676bc3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt
> @@ -0,0 +1,45 @@
> +Freescale i.MX7 CMOS Sensor Interface
> +=====================================
> +
> +csi node
> +--------
> +
> +This is device node for the CMOS Sensor Interface (CSI) which enables the chip
> +to connect directly to external CMOS image sensors.
> +
> +Required properties:
> +
> +- compatible : "fsl,imx7-csi";
> +- reg : base address and length of the register set for the device;
> +- interrupts : should contain CSI interrupt;
> +- clocks : list of clock specifiers, see
> + Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
> +- clock-names : must contain "axi", "mclk" and "dcic" entries, matching
> + entries in the clock property;
> +
> +The device node shall contain one 'port' child node with one child 'endpoint'
> +node, according to the bindings defined in:
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +In the following example a remote endpoint is a video multiplexer.
> +
> +example:
> +
> + csi: csi@30710000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + compatible = "fsl,imx7-csi";
> + reg = <0x30710000 0x10000>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX7D_CLK_DUMMY>,
> + <&clks IMX7D_CSI_MCLK_ROOT_CLK>,
> + <&clks IMX7D_CLK_DUMMY>;
> + clock-names = "axi", "mclk", "dcic";
> +
> + port {
> + csi_from_csi_mux: endpoint {
> + remote-endpoint = <&csi_mux_to_csi>;
> + };
> + };
> + };
> diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> new file mode 100644
> index 000000000000..71fd74ed3ec8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> @@ -0,0 +1,90 @@
> +Freescale i.MX7 Mipi CSI2
> +=========================
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is
> +compatible with previous version of Samsung D-phy.
> +
> +Required properties:
> +
> +- compatible : "fsl,imx7-mipi-csi2";
> +- reg : base address and length of the register set for the device;
> +- interrupts : should contain MIPI CSIS interrupt;
> +- clocks : list of clock specifiers, see
> + Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
> +- clock-names : must contain "pclk", "wrap" and "phy" entries, matching
> + entries in the clock property;
> +- power-domains : a phandle to the power domain, see
> + Documentation/devicetree/bindings/power/power_domain.txt for details.
> +- reset-names : should include following entry "mrst";
> +- resets : a list of phandle, should contain reset entry of
> + reset-names;
> +- phy-supply : from the generic phy bindings, a phandle to a regulator that
> + provides power to MIPI CSIS core;
> +
> +Optional properties:
> +
> +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
> + value when this property is not specified is 166 MHz;
> +- fsl,csis-hs-settle : differential receiver (HS-RX) settle time;
> +
> +The device node should contain two 'port' child nodes with one child 'endpoint'
> +node, according to the bindings defined in:
> + Documentation/devicetree/bindings/ media/video-interfaces.txt.
> + The following are properties specific to those nodes.
> +
> +port node
> +---------
> +
> +- reg : (required) can take the values 0 or 1, where 0 shall be
> + related to the sink port and port 1 shall be the source
> + one;
> +
> +endpoint node
> +-------------
> +
> +- data-lanes : (required) an array specifying active physical MIPI-CSI2
> + data input lanes and their mapping to logical lanes; this
> + shall only be applied to port 0 (sink port), the array's
> + content is unused only its length is meaningful,
> + in this case the maximum length supported is 2;
> +
> +example:
> +
> + mipi_csi: mipi-csi@30750000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + compatible = "fsl,imx7-mipi-csi2";
> + reg = <0x30750000 0x10000>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clks IMX7D_IPG_ROOT_CLK>,
> + <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
> + <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
> + clock-names = "pclk", "wrap", "phy";
> + clock-frequency = <166000000>;
> + power-domains = <&pgc_mipi_phy>;
> + phy-supply = <®_1p0d>;
> + resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
> + reset-names = "mrst";
> + fsl,csis-hs-settle = <3>;
> +
> + port@0 {
> + reg = <0>;
> +
> + mipi_from_sensor: endpoint {
> + remote-endpoint = <&ov2680_to_mipi>;
> + data-lanes = <1>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + mipi_vc0_to_csi_mux: endpoint {
> + remote-endpoint = <&csi_mux_from_mipi_vc0>;
> + };
> + };
> + };
>
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
