On Mon, Nov 26, 2018 at 08:46:10PM +0100, Sergio Paracuellos wrote: > On Mon, Nov 26, 2018 at 4:28 PM Greg KH <gregkh@xxxxxxxxxxxxxxxxxxx> wrote: > > > > On Sun, Nov 25, 2018 at 07:59:48AM +0100, Sergio Paracuellos wrote: > > > On Sat, Nov 24, 2018 at 9:05 PM NeilBrown <neil@xxxxxxxxxx> wrote: > > > > > > > > On Sat, Nov 24 2018, Sergio Paracuellos wrote: > > > > > > > > > Previous cleanup series was added to the staging tree without any > > > > > testing. After get testing feedback some issues appear and this patch > > > > > series should make the driver works properly again. > > > > > > > > > > Previous series are here: > > > > > * http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2018-November/128200.html > > > > > > > > > > Feedback after testing from Neil Brown is here: > > > > > * http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2018-November/129031.html > > > > > > > > > > There is one issue with chip revision and reset lines where those > > > > > are inverted. I achieve this including some wrappers for checking > > > > > the version in driver code and use proper reset_control_* functions. > > > > > I checked the 'arch/mips/ralink/reset.c' and think a good way to add > > > > > a quirk there but I ended up handling those inside the driver. > > > > > > > > > > Changes in v2: > > > > > - PATCH 7: In commit message: 's/mt7621-pcie/mt7621-pci/g' > > > > > > > > > > Hope this helps. > > > > > > > > > > Best regards, > > > > > Sergio Paracuellos > > > > > > > > > > Sergio Paracuellos (7): > > > > > staging: mt7621-pci: avoid mapping sysctls registers > > > > > staging: mt7621-dts: remove sysctl registers from pcie bindings > > > > > staging: mt7621-pci: dt-bindings: update bindings doc removing sysctls > > > > > registers > > > > > staging: mt7621-pci: fix reset lines for each pcie port > > > > > staging: mt7621-pci: avoid using clk_* operations > > > > > > > > all above: > > > > Tested-by: NeilBrown <neil@xxxxxxxxxx> > > > > > > > > Thanks! > > > > > > > > > staging: mt7621-dts: remove clocks for pcie bindings > > > > > staging: mt7621-pci: dt-bindings: update bindings doc removing clocks > > > > > > > > I don't think we really want these - at least, not yet. > > > > The clock numbers do appear in the driver as > > > > > > > > #define PCIE_PORT_CLK_EN(x) BIT(24 + (x)) > > > > > > > > and > > > > rt_sysc_m32(PCIE_PORT_CLK_EN(slot), 0, RALINK_CLKCFG1); > > > > Maybe that can be made generic... > > > > > > > > It is odd that the driver disables the clock, but never enables it. > > > > There is other clock-related code in the pci driver. Maybe it should > > > > just stay there, maybe it should go to a clock driver. I don't really > > > > know. But this dts stuff "looks" right, so I'd rather leave it until we > > > > know that it will be useless. > > > > > > Ok! I understand your point. Because those are the last two in the series, I > > > think there is no need to send v3 of this series without them. Greg, let me know > > > if you prefer me to send v3 without last two patches. > > > > I'll just drop the last two from my queue, no need to resend. > > Greg, It seems last two patches were finally applied and they > shouldn't be. Let me know if you need > me to send patches to revert them. Ugh, my fault, let me go redo that branch and drop them, thanks for catching this... greg k-h _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
