On 17/10/2018 10:47 PM, Nishad Kamdar wrote:
Use the gpiod interface for rdwr_pin, convert_pin and busy_pin
instead of the deprecated old non-descriptor interface.
Signed-off-by: Nishad Kamdar <nishadkamdar@xxxxxxxxx>
---
Changes in v2:
- Correct the error messages as pin number being showed
has now been replaced by error code.
---
drivers/staging/iio/adc/ad7816.c | 80 ++++++++++++++------------------
1 file changed, 34 insertions(+), 46 deletions(-)
diff --git a/drivers/staging/iio/adc/ad7816.c b/drivers/staging/iio/adc/ad7816.c
index bf76a8620bdb..12c4e0ab4713 100644
--- a/drivers/staging/iio/adc/ad7816.c
+++ b/drivers/staging/iio/adc/ad7816.c
@@ -7,7 +7,7 @@
*/
#include <linux/interrupt.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/device.h>
#include <linux/kernel.h>
#include <linux/slab.h>
@@ -44,9 +44,9 @@
struct ad7816_chip_info {
struct spi_device *spi_dev;
- u16 rdwr_pin;
- u16 convert_pin;
- u16 busy_pin;
+ struct gpio_desc *rdwr_pin;
+ struct gpio_desc *convert_pin;
+ struct gpio_desc *busy_pin;
u8 oti_data[AD7816_CS_MAX + 1];
u8 channel_id; /* 0 always be temperature */
u8 mode;
@@ -61,28 +61,28 @@ static int ad7816_spi_read(struct ad7816_chip_info *chip, u16 *data)
int ret = 0;
__be16 buf;
- gpio_set_value(chip->rdwr_pin, 1);
- gpio_set_value(chip->rdwr_pin, 0);
+ gpiod_set_value(chip->rdwr_pin, 1);
+ gpiod_set_value(chip->rdwr_pin, 0);
ret = spi_write(spi_dev, &chip->channel_id, sizeof(chip->channel_id));
if (ret < 0) {
dev_err(&spi_dev->dev, "SPI channel setting error\n");
return ret;
}
- gpio_set_value(chip->rdwr_pin, 1);
+ gpiod_set_value(chip->rdwr_pin, 1);
if (chip->mode == AD7816_PD) { /* operating mode 2 */
- gpio_set_value(chip->convert_pin, 1);
- gpio_set_value(chip->convert_pin, 0);
+ gpiod_set_value(chip->convert_pin, 1);
+ gpiod_set_value(chip->convert_pin, 0);
} else { /* operating mode 1 */
- gpio_set_value(chip->convert_pin, 0);
- gpio_set_value(chip->convert_pin, 1);
+ gpiod_set_value(chip->convert_pin, 0);
+ gpiod_set_value(chip->convert_pin, 1);
}
- while (gpio_get_value(chip->busy_pin))
+ while (gpiod_get_value(chip->busy_pin))
cpu_relax();
- gpio_set_value(chip->rdwr_pin, 0);
- gpio_set_value(chip->rdwr_pin, 1);
+ gpiod_set_value(chip->rdwr_pin, 0);
+ gpiod_set_value(chip->rdwr_pin, 1);
ret = spi_read(spi_dev, &buf, sizeof(*data));
if (ret < 0) {
dev_err(&spi_dev->dev, "SPI data read error\n");
@@ -99,8 +99,8 @@ static int ad7816_spi_write(struct ad7816_chip_info *chip, u8 data)
struct spi_device *spi_dev = chip->spi_dev;
int ret = 0;
- gpio_set_value(chip->rdwr_pin, 1);
- gpio_set_value(chip->rdwr_pin, 0);
+ gpiod_set_value(chip->rdwr_pin, 1);
+ gpiod_set_value(chip->rdwr_pin, 0);
ret = spi_write(spi_dev, &data, sizeof(data));
if (ret < 0)
dev_err(&spi_dev->dev, "SPI oti data write error\n");
@@ -129,10 +129,10 @@ static ssize_t ad7816_store_mode(struct device *dev,
struct ad7816_chip_info *chip = iio_priv(indio_dev);
if (strcmp(buf, "full")) {
- gpio_set_value(chip->rdwr_pin, 1);
+ gpiod_set_value(chip->rdwr_pin, 1);
chip->mode = AD7816_FULL;
} else {
- gpio_set_value(chip->rdwr_pin, 0);
+ gpiod_set_value(chip->rdwr_pin, 0);
chip->mode = AD7816_PD;
}
@@ -345,15 +345,9 @@ static int ad7816_probe(struct spi_device *spi_dev)
{
struct ad7816_chip_info *chip;
struct iio_dev *indio_dev;
- unsigned short *pins = dev_get_platdata(&spi_dev->dev);
int ret = 0;
int i;
- if (!pins) {
- dev_err(&spi_dev->dev, "No necessary GPIO platform data.\n");
- return -EINVAL;
- }
-
indio_dev = devm_iio_device_alloc(&spi_dev->dev, sizeof(*chip));
if (!indio_dev)
return -ENOMEM;
@@ -364,34 +358,28 @@ static int ad7816_probe(struct spi_device *spi_dev)
chip->spi_dev = spi_dev;
for (i = 0; i <= AD7816_CS_MAX; i++)
chip->oti_data[i] = 203;
- chip->rdwr_pin = pins[0];
- chip->convert_pin = pins[1];
- chip->busy_pin = pins[2];
-
- ret = devm_gpio_request(&spi_dev->dev, chip->rdwr_pin,
- spi_get_device_id(spi_dev)->name);
- if (ret) {
- dev_err(&spi_dev->dev, "Fail to request rdwr gpio PIN %d.\n",
- chip->rdwr_pin);
+
+ chip->rdwr_pin = devm_gpiod_get(&spi_dev->dev, "rdwr", GPIOD_IN);
+ if (IS_ERR(chip->rdwr_pin)) {
+ ret = PTR_ERR(chip->rdwr_pin);
+ dev_err(&spi_dev->dev, "Failed to request rdwr GPIO: %d\n",
+ ret);
return ret;
}
- gpio_direction_input(chip->rdwr_pin);
The RD/WR pin is an input to the AD78xx. So this doesn't make sense being GPIOD_IN.
- ret = devm_gpio_request(&spi_dev->dev, chip->convert_pin,
- spi_get_device_id(spi_dev)->name);
- if (ret) {
- dev_err(&spi_dev->dev, "Fail to request convert gpio PIN %d.\n",
- chip->convert_pin);
+ chip->convert_pin = devm_gpiod_get(&spi_dev->dev, "convert", GPIOD_IN);
+ if (IS_ERR(chip->convert_pin)) {
+ ret = PTR_ERR(chip->convert_pin);
+ dev_err(&spi_dev->dev, "Failed to request convert GPIO: %d\n",
+ ret);
return ret;
}
- gpio_direction_input(chip->convert_pin);
ditto, the CONVST pin is an input to the AD78xx.
- ret = devm_gpio_request(&spi_dev->dev, chip->busy_pin,
- spi_get_device_id(spi_dev)->name);
- if (ret) {
- dev_err(&spi_dev->dev, "Fail to request busy gpio PIN %d.\n",
- chip->busy_pin);
+ chip->busy_pin = devm_gpiod_get(&spi_dev->dev, "busy", GPIOD_IN);
+ if (IS_ERR(chip->busy_pin)) {
+ ret = PTR_ERR(chip->busy_pin);
+ dev_err(&spi_dev->dev, "Failed to request busy GPIO: %d\n",
+ ret);
return ret;
}
- gpio_direction_input(chip->busy_pin);
The busy pin doesn't exist on the ad7818.
Which the driver claims to support in the id table:
> static const struct spi_device_id ad7816_id[] = {
> { "ad7816", 0 },
> { "ad7817", 0 },
> { "ad7818", 0 },
> {}
> };
See:
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7817_7818.pdf
Page 9.
indio_dev->name = spi_get_device_id(spi_dev)->name;
indio_dev->dev.parent = &spi_dev->dev;
Also should the pin names be documented in a device tree binding doc?
--
Regards
Phil Reid
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
