RALINK_PCI_BASE has no sense and this driver has base address readed
and mapped from device tree. Remove remaining uses of it and
change code to use pcie_read and pcie_write functions in places
where this was being used.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@xxxxxxxxx>
---
drivers/staging/mt7621-pci/pci-mt7621.c | 131 ++++++++++++++++----------------
1 file changed, 67 insertions(+), 64 deletions(-)
diff --git a/drivers/staging/mt7621-pci/pci-mt7621.c b/drivers/staging/mt7621-pci/pci-mt7621.c
index 034c6c5..93821aa 100644
--- a/drivers/staging/mt7621-pci/pci-mt7621.c
+++ b/drivers/staging/mt7621-pci/pci-mt7621.c
@@ -76,7 +76,6 @@
#define RALINK_PCI_PCICFG_ADDR 0x0000
#define RALINK_PCI_PCIMSK_ADDR 0x000C
-#define RALINK_PCI_BASE 0xBE140000
#define RT6855_PCIE0_OFFSET 0x2000
#define RT6855_PCIE1_OFFSET 0x3000
@@ -89,8 +88,8 @@
#define RALINK_PCI_SUBID 0x0038
#define RALINK_PCI_STATUS 0x0050
-#define RALINK_PCIEPHY_P0P1_CTL_OFFSET (RALINK_PCI_BASE + 0x9000)
-#define RALINK_PCIEPHY_P2_CTL_OFFSET (RALINK_PCI_BASE + 0xA000)
+#define RALINK_PCIEPHY_P0P1_CTL_OFFSET 0x9000
+#define RALINK_PCIEPHY_P2_CTL_OFFSET 0xA000
#define RALINK_PCI_MM_MAP_BASE 0x60000000
#define RALINK_PCI_IO_MAP_BASE 0x1e160000
@@ -231,105 +230,109 @@ pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
}
void
-set_pcie_phy(u32 *addr, int start_b, int bits, int val)
+set_pcie_phy(struct mt7621_pcie *pcie, u32 offset,
+ int start_b, int bits, int val)
{
- *(unsigned int *)(addr) &= ~(((1<<bits) - 1)<<start_b);
- *(unsigned int *)(addr) |= val << start_b;
+ u32 reg = pcie_read(pcie, offset);
+
+ reg &= ~(((1 << bits) - 1) << start_b);
+ reg |= val << start_b;
+ pcie_write(pcie, reg, offset);
}
void
-bypass_pipe_rst(void)
+bypass_pipe_rst(struct mt7621_pcie *pcie)
{
/* PCIe Port 0 */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
/* PCIe Port 1 */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x12c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
/* PCIe Port 2 */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 12, 1, 0x01); // rg_pe1_pipe_rst_b
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x02c), 4, 1, 0x01); // rg_pe1_pipe_cmd_frc[4]
}
void
-set_phy_for_ssc(void)
+set_phy_for_ssc(struct mt7621_pcie *pcie)
{
unsigned long reg = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0);
reg = (reg >> 6) & 0x7;
/* Set PCIe Port0 & Port1 PHY to disable SSC */
/* Debug Xtal Type */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 1 enable control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x00); // rg_pe1_phy_en //Port 1 disable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 1 enable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x00); // rg_pe1_phy_en //Port 1 disable
if (reg <= 5 && reg >= 3) { // 40MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
printk("***** Xtal 40MHz *****\n");
} else { // 25MHz | 20MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
if (reg >= 6) {
printk("***** Xtal 25MHz *****\n");
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x49c), 0, 31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode)
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a4), 0, 16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 0, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 16, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x49c), 0, 31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a4), 0, 16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 0, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a8), 16, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial
} else {
printk("***** Xtal 20MHz *****\n");
}
}
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN
if (reg <= 5 && reg >= 3) { // 40MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv
}
/* Enable PHY and disable force mode */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x01); // rg_pe1_phy_en //Port 1 enable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 1 disable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 5, 1, 0x01); // rg_pe1_phy_en //Port 1 enable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P0P1_CTL_OFFSET + 0x100), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 1 disable control
/* Set PCIe Port2 PHY to disable SSC */
/* Debug Xtal Type */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 8, 1, 0x01); // rg_pe1_frc_h_xtal_type
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x400), 9, 2, 0x00); // rg_pe1_h_xtal_type
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x01); // rg_pe1_frc_phy_en //Force Port 0 enable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x00); // rg_pe1_phy_en //Port 0 disable
if (reg <= 5 && reg >= 3) { // 40MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x01); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
} else { // 25MHz | 20MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 6, 2, 0x00); // RG_PE1_H_PLL_PREDIV //Pre-divider ratio (for host mode)
if (reg >= 6) { // 25MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x49c), 0, 31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode)
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a4), 0, 16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 0, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 16, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4bc), 4, 2, 0x01); // RG_PE1_H_PLL_FBKSEL //Feedback clock select
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x49c), 0, 31, 0x18000000); // RG_PE1_H_LCDDS_PCW_NCPO //DDS NCPO PCW (for host mode)
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a4), 0, 16, 0x18d); // RG_PE1_H_LCDDS_SSC_PRD //DDS SSC dither period control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 0, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA //DDS SSC dither amplitude control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a8), 16, 12, 0x4a); // RG_PE1_H_LCDDS_SSC_DELTA1 //DDS SSC dither amplitude control for initial
}
}
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4a0), 5, 1, 0x01); // RG_PE1_LCDDS_CLK_PH_INV //DDS clock inversion
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 22, 2, 0x02); // RG_PE1_H_PLL_BC
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 18, 4, 0x06); // RG_PE1_H_PLL_BP
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 12, 4, 0x02); // RG_PE1_H_PLL_IR
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 8, 4, 0x01); // RG_PE1_H_PLL_IC
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x4ac), 16, 3, 0x00); // RG_PE1_H_PLL_BR
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x490), 1, 3, 0x02); // RG_PE1_PLL_DIVEN
if (reg <= 5 && reg >= 3) { // 40MHz Xtal
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 6, 2, 0x01); // rg_pe1_mstckdiv //value of da_pe1_mstckdiv when force mode enable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x414), 5, 1, 0x01); // rg_pe1_frc_mstckdiv //force mode enable of da_pe1_mstckdiv
}
/* Enable PHY and disable force mode */
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable
- set_pcie_phy((u32 *)(RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 5, 1, 0x01); // rg_pe1_phy_en //Port 0 enable
+ set_pcie_phy(pcie, (RALINK_PCIEPHY_P2_CTL_OFFSET + 0x000), 4, 1, 0x00); // rg_pe1_frc_phy_en //Force Port 0 disable control
}
static int mt7621_pci_parse_request_of_pci_ranges(struct device *dev,
@@ -449,8 +452,8 @@ static int mt7621_pci_probe(struct platform_device *pdev)
DEASSERT_SYSRST_PCIE(val);
if ((*(unsigned int *)(0xbe00000c)&0xFFFF) == 0x0101) // MT7621 E2
- bypass_pipe_rst();
- set_phy_for_ssc();
+ bypass_pipe_rst(pcie);
+ set_phy_for_ssc(pcie);
val = read_config(pcie, 0, 0x70c);
printk("Port 0 N_FTS = %x\n", (unsigned int)val);
--
2.7.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
