The source module antsel is always included in the current driver so
any checks for it being compiled in are redundant and have been removed.
Reviewed-by: Roland Vossen <rvossen@xxxxxxxxxxxx>
Reviewed-by: Brett Rudley <brudley@xxxxxxxxxxxx>
Signed-off-by: Arend van Spriel <arend@xxxxxxxxxxxx>
---
drivers/staging/brcm80211/brcmsmac/wlc_ampdu.c | 3 +-
drivers/staging/brcm80211/brcmsmac/wlc_antsel.c | 4 --
drivers/staging/brcm80211/brcmsmac/wlc_bmac.c | 64 +++++++++++-----------
drivers/staging/brcm80211/brcmsmac/wlc_cfg.h | 6 --
drivers/staging/brcm80211/brcmsmac/wlc_main.c | 25 +++------
5 files changed, 42 insertions(+), 60 deletions(-)
diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_ampdu.c b/drivers/staging/brcm80211/brcmsmac/wlc_ampdu.c
index de50a8c..f0a591a 100644
--- a/drivers/staging/brcm80211/brcmsmac/wlc_ampdu.c
+++ b/drivers/staging/brcm80211/brcmsmac/wlc_ampdu.c
@@ -1178,8 +1178,7 @@ wlc_ampdu_dotxstatus_complete(struct ampdu_info *ampdu, struct scb *scb,
wlc_send_q(wlc, wlc->active_queue);
/* update rate state */
- if (WLANTSEL_ENAB(wlc))
- antselid = wlc_antsel_antsel2id(wlc->asi, mimoantsel);
+ antselid = wlc_antsel_antsel2id(wlc->asi, mimoantsel);
wlc_txfifo_complete(wlc, queue, ampdu->txpkt_weight);
}
diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_antsel.c b/drivers/staging/brcm80211/brcmsmac/wlc_antsel.c
index 14dd312..b9e68ea 100644
--- a/drivers/staging/brcm80211/brcmsmac/wlc_antsel.c
+++ b/drivers/staging/brcm80211/brcmsmac/wlc_antsel.c
@@ -16,8 +16,6 @@
#include <wlc_cfg.h>
-#ifdef WLANTSEL
-
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -326,5 +324,3 @@ static int wlc_antsel_cfgupd(struct antsel_info *asi, wlc_antselcfg_t *antsel)
return 0;
}
-
-#endif /* WLANTSEL */
diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c b/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c
index 2392b65..6558857 100644
--- a/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c
+++ b/drivers/staging/brcm80211/brcmsmac/wlc_bmac.c
@@ -2582,39 +2582,39 @@ static void wlc_gpio_init(struct wlc_info *wlc)
gc = gm = 0;
/* Allocate GPIOs for mimo antenna diversity feature */
- if (WLANTSEL_ENAB(wlc)) {
- if (wlc_hw->antsel_type == ANTSEL_2x3) {
- /* Enable antenna diversity, use 2x3 mode */
- wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_EN,
- MHF3_ANTSEL_EN, WLC_BAND_ALL);
- wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_MODE,
- MHF3_ANTSEL_MODE, WLC_BAND_ALL);
-
- /* init superswitch control */
- wlc_phy_antsel_init(wlc_hw->band->pi, false);
-
- } else if (wlc_hw->antsel_type == ANTSEL_2x4) {
- ASSERT((gm & BOARD_GPIO_12) == 0);
- gm |= gc |= (BOARD_GPIO_12 | BOARD_GPIO_13);
- /* The board itself is powered by these GPIOs (when not sending pattern)
- * So set them high
- */
- OR_REG(osh, ®s->psm_gpio_oe,
- (BOARD_GPIO_12 | BOARD_GPIO_13));
- OR_REG(osh, ®s->psm_gpio_out,
- (BOARD_GPIO_12 | BOARD_GPIO_13));
-
- /* Enable antenna diversity, use 2x4 mode */
- wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_EN,
- MHF3_ANTSEL_EN, WLC_BAND_ALL);
- wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_MODE, 0,
- WLC_BAND_ALL);
-
- /* Configure the desired clock to be 4Mhz */
- wlc_bmac_write_shm(wlc_hw, M_ANTSEL_CLKDIV,
- ANTSEL_CLKDIV_4MHZ);
- }
+ if (wlc_hw->antsel_type == ANTSEL_2x3) {
+ /* Enable antenna diversity, use 2x3 mode */
+ wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_EN,
+ MHF3_ANTSEL_EN, WLC_BAND_ALL);
+ wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_MODE,
+ MHF3_ANTSEL_MODE, WLC_BAND_ALL);
+
+ /* init superswitch control */
+ wlc_phy_antsel_init(wlc_hw->band->pi, false);
+
+ } else if (wlc_hw->antsel_type == ANTSEL_2x4) {
+ ASSERT((gm & BOARD_GPIO_12) == 0);
+ gm |= gc |= (BOARD_GPIO_12 | BOARD_GPIO_13);
+ /*
+ * The board itself is powered by these GPIOs
+ * (when not sending pattern) so set them high
+ */
+ OR_REG(osh, ®s->psm_gpio_oe,
+ (BOARD_GPIO_12 | BOARD_GPIO_13));
+ OR_REG(osh, ®s->psm_gpio_out,
+ (BOARD_GPIO_12 | BOARD_GPIO_13));
+
+ /* Enable antenna diversity, use 2x4 mode */
+ wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_EN,
+ MHF3_ANTSEL_EN, WLC_BAND_ALL);
+ wlc_bmac_mhf(wlc_hw, MHF3, MHF3_ANTSEL_MODE, 0,
+ WLC_BAND_ALL);
+
+ /* Configure the desired clock to be 4Mhz */
+ wlc_bmac_write_shm(wlc_hw, M_ANTSEL_CLKDIV,
+ ANTSEL_CLKDIV_4MHZ);
}
+
/* gpio 9 controls the PA. ucode is responsible for wiggling out and oe */
if (wlc_hw->boardflags & BFL_PACTRL)
gm |= gc |= BOARD_GPIO_PACTRL;
diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_cfg.h b/drivers/staging/brcm80211/brcmsmac/wlc_cfg.h
index 3decb7d..85fbd06 100644
--- a/drivers/staging/brcm80211/brcmsmac/wlc_cfg.h
+++ b/drivers/staging/brcm80211/brcmsmac/wlc_cfg.h
@@ -69,10 +69,6 @@
#define SSLPNCONF SSLPNPHY_DEFAULT
#endif
-#define BAND2G
-#define BAND5G
-#define WLANTSEL 1
-
/********************************************************************
* Phy/Core Configuration. Defines macros to to check core phy/rev *
* compile-time configuration. Defines default core support. *
@@ -281,6 +277,4 @@
#define WLBANDINITDATA(_data) _data
#define WLBANDINITFN(_fn) _fn
-#define WLANTSEL_ENAB(wlc) 1
-
#endif /* _wlc_cfg_h_ */
diff --git a/drivers/staging/brcm80211/brcmsmac/wlc_main.c b/drivers/staging/brcm80211/brcmsmac/wlc_main.c
index b48561a..c8d0f7a 100644
--- a/drivers/staging/brcm80211/brcmsmac/wlc_main.c
+++ b/drivers/staging/brcm80211/brcmsmac/wlc_main.c
@@ -895,8 +895,7 @@ void wlc_set_chanspec(struct wlc_info *wlc, chanspec_t chanspec)
/* init antenna selection */
if (CHSPEC_WLC_BW(old_chanspec) != CHSPEC_WLC_BW(chanspec)) {
- if (WLANTSEL_ENAB(wlc))
- wlc_antsel_init(wlc->asi);
+ wlc_antsel_init(wlc->asi);
/* Fix the hardware rateset based on bw.
* Mainly add MCS32 for 40Mhz, remove MCS 32 for 20Mhz
@@ -1349,8 +1348,7 @@ static void WLBANDINITFN(wlc_bsinit) (struct wlc_info *wlc)
wlc_ucode_mac_upd(wlc);
/* init antenna selection */
- if (WLANTSEL_ENAB(wlc))
- wlc_antsel_init(wlc->asi);
+ wlc_antsel_init(wlc->asi);
}
@@ -2055,15 +2053,13 @@ void *wlc_attach(void *wl, u16 vendor, u16 device, uint unit, bool piomode,
/* initialize radio_mpc_disable according to wlc->mpc */
wlc_radio_mpc_upd(wlc);
- if (WLANTSEL_ENAB(wlc)) {
- if ((wlc->pub->sih->chip) == BCM43235_CHIP_ID) {
- if ((getintvar(wlc->pub->vars, "aa2g") == 7) ||
- (getintvar(wlc->pub->vars, "aa5g") == 7)) {
- wlc_bmac_antsel_set(wlc->hw, 1);
- }
- } else {
- wlc_bmac_antsel_set(wlc->hw, wlc->asi->antsel_avail);
+ if ((wlc->pub->sih->chip) == BCM43235_CHIP_ID) {
+ if ((getintvar(wlc->pub->vars, "aa2g") == 7) ||
+ (getintvar(wlc->pub->vars, "aa5g") == 7)) {
+ wlc_bmac_antsel_set(wlc->hw, 1);
}
+ } else {
+ wlc_bmac_antsel_set(wlc->hw, wlc->asi->antsel_avail);
}
if (perr)
@@ -5904,11 +5900,9 @@ wlc_d11hdrs_mac80211(struct wlc_info *wlc, struct ieee80211_hw *hw,
u32 rate_val[2];
bool hwtkmic = false;
u16 mimo_ctlchbw = PHY_TXC1_BW_20MHZ;
-#ifdef WLANTSEL
#define ANTCFG_NONE 0xFF
u8 antcfg = ANTCFG_NONE;
u8 fbantcfg = ANTCFG_NONE;
-#endif
uint phyctl1_stf = 0;
u16 durid = 0;
struct ieee80211_tx_rate *txrate[2];
@@ -6047,8 +6041,7 @@ wlc_d11hdrs_mac80211(struct wlc_info *wlc, struct ieee80211_hw *hw,
ASSERT(RSPEC_ACTIVE(rspec[k]));
rspec[k] = WLC_RATE_1M;
} else {
- if (WLANTSEL_ENAB(wlc) &&
- !is_multicast_ether_addr(h->addr1)) {
+ if (!is_multicast_ether_addr(h->addr1)) {
/* set tx antenna config */
wlc_antsel_antcfg_get(wlc->asi, false, false, 0,
0, &antcfg, &fbantcfg);
--
1.7.1
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
