Le mercredi 30 mai 2018 à 14:17:25 (+0300), Dan Carpenter a écrit :
> On Tue, May 29, 2018 at 09:11:43PM +0200, Thibaut Robert wrote:
> > diff --git a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
> > index e248702ee519..745bf5ca2622 100644
> > --- a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
> > +++ b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
> > @@ -1431,7 +1431,7 @@ void wilc_wfi_p2p_rx(struct net_device *dev, u8 *buff, u32 size)
> >
> > freq = ieee80211_channel_to_frequency(curr_channel, NL80211_BAND_2GHZ);
> >
> > - if (!ieee80211_is_action(buff[FRAME_TYPE_ID])) {
> > + if (!ieee80211_is_action(cpu_to_le16(buff[FRAME_TYPE_ID]))) {
>
> "buff" comes from the network, it's going to be little endian, not cpu
> endian. The rest of the function treats it as CPU endian but I'm pretty
> sure it's wrong...
buff comes from the network but we are looking at single byte here.
ieee80211_is_action expects an le16, so we I added this to extend an u8
to an le16. Is this incorrect ?
Or maybe we the buff has the second byte ? but that I can't tell.
>
> > cfg80211_rx_mgmt(priv->wdev, freq, 0, buff, size, 0);
> > return;
> > }
>
>
> > diff --git a/drivers/staging/wilc1000/wilc_wlan.c b/drivers/staging/wilc1000/wilc_wlan.c
> > index 28c93f3f846e..a5ac1d26590b 100644
> > --- a/drivers/staging/wilc1000/wilc_wlan.c
> > +++ b/drivers/staging/wilc1000/wilc_wlan.c
> > @@ -560,7 +560,8 @@ int wilc_wlan_handle_txq(struct net_device *dev, u32 *txq_count)
> > int ret = 0;
> > int counter;
> > int timeout;
> > - u32 vmm_table[WILC_VMM_TBL_SIZE];
> > + __le32 vmm_table[WILC_VMM_TBL_SIZE];
> > + u32 table_entry;
> > struct wilc_vif *vif;
> > struct wilc *wilc;
> > const struct wilc_hif_func *func;
> > @@ -598,10 +599,10 @@ int wilc_wlan_handle_txq(struct net_device *dev, u32 *txq_count)
> > if ((sum + vmm_sz) > LINUX_TX_SIZE)
> > break;
> >
> > - vmm_table[i] = vmm_sz / 4;
> > + table_entry = vmm_sz / 4;
> > if (tqe->type == WILC_CFG_PKT)
> > - vmm_table[i] |= BIT(10);
> > - vmm_table[i] = cpu_to_le32(vmm_table[i]);
> > + table_entry |= BIT(10);
> > + vmm_table[i] = cpu_to_le32(table_entry);
> >
> > i++;
> > sum += vmm_sz;
> > @@ -704,8 +705,7 @@ int wilc_wlan_handle_txq(struct net_device *dev, u32 *txq_count)
> > if (vmm_table[i] == 0)
> > break;
> >
> > - vmm_table[i] = cpu_to_le32(vmm_table[i]);
> > - vmm_sz = (vmm_table[i] & 0x3ff);
> > + vmm_sz = (le32_to_cpu(vmm_table[i]) & 0x3ff);
> > vmm_sz *= 4;
> > header = (tqe->type << 31) |
> > (tqe->buffer_size << 15) |
> > @@ -715,8 +715,7 @@ int wilc_wlan_handle_txq(struct net_device *dev, u32 *txq_count)
> > else
> > header &= ~BIT(30);
> >
> > - header = cpu_to_le32(header);
> > - memcpy(&txb[offset], &header, 4);
> > + *((__le32 *)&txb[offset]) = cpu_to_le32(header);
>
> I worry about alignment issues here. That might be the reason for the
> memcpy(). (I'm reading as fast as I can and don't the code so I may
> be wrong).
>
> > if (tqe->type == WILC_CFG_PKT) {
> > buffer_offset = ETH_CONFIG_PKT_HDR_OFFSET;
> > } else if (tqe->type == WILC_NET_PKT) {
> > @@ -770,8 +769,7 @@ static void wilc_wlan_handle_rx_buff(struct wilc *wilc, u8 *buffer, int size)
> >
> > do {
> > buff_ptr = buffer + offset;
> > - memcpy(&header, buff_ptr, 4);
> > - header = cpu_to_le32(header);
> > + header = le32_to_cpup((__le32 *)buff_ptr);
>
> Maybe the same, whenever you see a memcpy().
>
> >
> > is_cfg_packet = (header >> 31) & 0x1;
> > pkt_offset = (header >> 22) & 0x1ff;
> > @@ -942,6 +940,7 @@ int wilc_wlan_firmware_download(struct wilc *wilc, const u8 *buffer,
> > u32 offset;
> > u32 addr, size, size2, blksz;
> > u8 *dma_buffer;
> > + const __le32 *header;
> > int ret = 0;
> >
> > blksz = BIT(12);
> > @@ -952,10 +951,9 @@ int wilc_wlan_firmware_download(struct wilc *wilc, const u8 *buffer,
> >
> > offset = 0;
> > do {
> > - memcpy(&addr, &buffer[offset], 4);
> > - memcpy(&size, &buffer[offset + 4], 4);
> > - addr = cpu_to_le32(addr);
> > - size = cpu_to_le32(size);
> > + header = (__le32 *)buffer + offset;
> > + addr = le32_to_cpu(header[0]);
> > + size = le32_to_cpu(header[1]);
> > acquire_bus(wilc, ACQUIRE_ONLY);
> > offset += 8;
> > while (((int)size) && (offset < buffer_size)) {
> > diff --git a/drivers/staging/wilc1000/wilc_wlan_cfg.c b/drivers/staging/wilc1000/wilc_wlan_cfg.c
> > index c0b9b700f4d7..4a914d8572aa 100644
> > --- a/drivers/staging/wilc1000/wilc_wlan_cfg.c
> > +++ b/drivers/staging/wilc1000/wilc_wlan_cfg.c
> > @@ -275,14 +275,14 @@ static int wilc_wlan_cfg_set_bin(u8 *frame, u32 offset, u16 id, u8 *b, u32 size)
> >
> > static void wilc_wlan_parse_response_frame(u8 *info, int size)
> > {
> > - u32 wid, len = 0, i = 0;
> > + u32 wid;
> > + int len = 0, i = 0;
>
> Why did we make these int now?
>
> >
> > while (size > 0) {
> > i = 0;
> > - wid = info[0] | (info[1] << 8);
> > - wid = cpu_to_le32(wid);
> > + wid = le16_to_cpup((__le16 *)info);
> >
> > - switch ((wid >> 12) & 0x7) {
> > + switch (info[1] >> 4) {
>
> Why do we not need to mask by 0x7? Anyway, I feel like this isn't
> beautiful. We should be using a macro and "wid" instead of magically
> poking into info[1].
>
> switch(SOME_MACRO(wid)) {
>
>
> regards,
> dan carpenter
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
