On Thu, 4 Jan 2018 22:06:31 +0530 Sumit Pundir <pundirsumit11@xxxxxxxxx> wrote: Patch title needs to mention the specific driver being changed. > This patch fixes the following checkpatch.pl error at multiple lines: > > CHECK: Prefer using the BIT macro > > Signed-off-by: Sumit Pundir <pundirsumit11@xxxxxxxxx> The BIT Macros is just fine if they are actually a single bit field. Some of these are not. See below. You really have to check the datasheet to be sure on these though in the cases here it's obvious from the surrounding lines. Changing those ones to BIT will actively hurt readability. Anyhow, the other cases are good so if you can prepare a patch changing just that and ensd it that would be great. > --- > drivers/staging/iio/cdc/ad7152.c | 12 ++++++------ > 1 file changed, 6 insertions(+), 6 deletions(-) > > diff --git a/drivers/staging/iio/cdc/ad7152.c b/drivers/staging/iio/cdc/ad7152.c > index 59d1b35..b2b15b9 100644 > --- a/drivers/staging/iio/cdc/ad7152.c > +++ b/drivers/staging/iio/cdc/ad7152.c > @@ -47,24 +47,24 @@ > #define AD7152_STATUS_PWDN BIT(7) > > /* Setup Register Bit Designations (AD7152_REG_CHx_SETUP) */ > -#define AD7152_SETUP_CAPDIFF (1 << 5) > +#define AD7152_SETUP_CAPDIFF BIT(5) This is indeed a 1 bit field so fine. > #define AD7152_SETUP_RANGE_2pF (0 << 6) > -#define AD7152_SETUP_RANGE_0_5pF (1 << 6) > +#define AD7152_SETUP_RANGE_0_5pF BIT(6) This is clearly putting the value 1 in a 2 bit field within the register - BIT macro obscures this compeltely. > #define AD7152_SETUP_RANGE_1pF (2 << 6) > #define AD7152_SETUP_RANGE_4pF (3 << 6) > #define AD7152_SETUP_RANGE(x) ((x) << 6) > > /* Config Register Bit Designations (AD7152_REG_CFG) */ > -#define AD7152_CONF_CH2EN (1 << 3) > -#define AD7152_CONF_CH1EN (1 << 4) > +#define AD7152_CONF_CH2EN BIT(3) > +#define AD7152_CONF_CH1EN BIT(4) These two are valid I think. > #define AD7152_CONF_MODE_IDLE (0 << 0) > -#define AD7152_CONF_MODE_CONT_CONV (1 << 0) > +#define AD7152_CONF_MODE_CONT_CONV BIT(0) This one is not. Again clear from the code let alone checking the datasheet. We write 6 to the same location. > #define AD7152_CONF_MODE_SINGLE_CONV (2 << 0) > #define AD7152_CONF_MODE_OFFS_CAL (5 << 0) > #define AD7152_CONF_MODE_GAIN_CAL (6 << 0) > > /* Capdac Register Bit Designations (AD7152_REG_CAPDAC_XXX) */ > -#define AD7152_CAPDAC_DACEN (1 << 7) > +#define AD7152_CAPDAC_DACEN BIT(7) This one is a 1 bit field so fine. > #define AD7152_CAPDAC_DACP(x) ((x) & 0x1F) > > /* CFG2 Register Bit Designations (AD7152_REG_CFG2) */ _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
