From: Andrew Lunn <andrew@xxxxxxx> Signed-off-by: Marek Lindner <lindner_marek@xxxxxxxx> Signed-off-by: Andrew Lunn <andrew@xxxxxxx> Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxx> --- drivers/staging/batman-adv/README | 275 +++++++++++++++++++++++-------------- 1 files changed, 173 insertions(+), 102 deletions(-) diff --git a/drivers/staging/batman-adv/README b/drivers/staging/batman-adv/README index e2a7271..14244a2 100644 --- a/drivers/staging/batman-adv/README +++ b/drivers/staging/batman-adv/README @@ -1,169 +1,240 @@ -[state: 22-03-2010] +[state: 03-05-2010] BATMAN-ADV ---------- -Batman-advanced is a new approach to wireless networking which does no longer -operate on the IP basis. Unlike B.A.T.M.A.N, which exchanges information -using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI -Layer 2 only and uses and routes (or better: bridges) Ethernet Frames. It -emulates a virtual network switch of all nodes participating. Therefore all -nodes appear to be link local, thus all higher operating protocols won't be -affected by any changes within the network. You can run almost any protocol -above B.A.T.M.A.N. Advanced, prominent examples are: IPv4, IPv6, DHCP, IPX. +Batman advanced is a new approach to wireless networking which +does no longer operate on the IP basis. Unlike the batman daemon, +which exchanges information using UDP packets and sets routing +tables, batman-advanced operates on ISO/OSI Layer 2 only and uses +and routes (or better: bridges) Ethernet Frames. It emulates a +virtual network switch of all nodes participating. Therefore all +nodes appear to be link local, thus all higher operating proto- +cols won't be affected by any changes within the network. You can +run almost any protocol above batman advanced, prominent examples +are: IPv4, IPv6, DHCP, IPX. -This is batman-advanced implemented as Linux kernel driver. It does not depend -on any network (other) driver, and can be used on wifi as well as ethernet, -vpn, etc ... (anything with ethernet-style layer 2). +Batman advanced was implemented as a Linux kernel driver to re- +duce the overhead to a minimum. It does not depend on any (other) +network driver, and can be used on wifi as well as ethernet lan, +vpn, etc ... (anything with ethernet-style layer 2). -USAGE ------ +CONFIGURATION +------------- -insmod the batman-adv.ko in your kernel: +Load the batman-adv module into your kernel: # insmod batman-adv.ko -the module is now waiting for activation. You must add some interfaces -on which batman can operate. Each interface must be added separately: +The module is now waiting for activation. You must add some in- +terfaces on which batman can operate. After loading the module +batman advanced will scan your systems interfaces to search for +compatible interfaces. Once found, it will create subfolders in +the /sys directories of each supported interface, e.g. -# echo wlan0 > /proc/net/batman-adv/interfaces +# ls /sys/class/net/eth0/batman_adv/ +# iface_status mesh_iface -( # echo wlan1 > /proc/net/batman-adv/interfaces ) -( # echo eth0 > /proc/net/batman-adv/interfaces ) -( ... ) +If an interface does not have the "batman_adv" subfolder it prob- +ably is not supported. Not supported interfaces are: loopback, +non-ethernet and batman's own interfaces. -Now batman starts broadcasting on this interface. -You can now view the table of originators (mesh participants) with: +Note: After the module was loaded it will continuously watch for +new interfaces to verify the compatibility. There is no need to +reload the module if you plug your USB wifi adapter into your ma- +chine after batman advanced was initially loaded. -# cat /proc/net/batman-adv/originators +To activate a given interface simply write "bat0" into its +"mesh_iface" file inside the batman_adv subfolder: -The module will create a new interface "bat0", which can be used as a -regular interface: +# echo bat0 > /sys/class/net/eth0/batman_adv/mesh_iface -# ifconfig bat0 inet 192.168.0.1 up -# ping 192.168.0.2 -... +Repeat this step for all interfaces you wish to add. Now batman +starts using/broadcasting on this/these interface(s). ---- -If you want topology visualization, your meshnode must be configured -as VIS-server: +By reading the "iface_status" file you can check its status: -# echo "server" > /proc/net/batman-adv/vis_server +# cat /sys/class/net/eth0/batman_adv/iface_status +# active -Each node is either configured as "server" or as "client" (default: -"client"). Clients send their topology data to the server next to them, -and server synchronize with other servers. If there is no server -configured (default) within the mesh, no topology information will be -transmitted. With these "synchronizing servers", there can be 1 or -more vis servers sharing the same (or at least very similar) data. +To deactivate an interface you have to write "none" into its +"mesh_iface" file: -When configured as server, you can get a topology snapshot of your mesh: +# echo none > /sys/class/net/eth0/batman_adv/mesh_iface -# cat /proc/net/batman-adv/vis_data -This raw output is intended to be easily parsable and convertable with -other tools. Have a look at the batctl README if you want a vis output -in dot or json format for instance and how those outputs could then be -visualised in an image. +All mesh wide settings can be found in batman's own interface +folder: + +# ls /sys/class/net/bat0/mesh/ +# aggregate_ogm originators transtable_global vis_mode +# orig_interval transtable_local vis_data + + +Some of the files contain all sort of status information regard- +ing the mesh network. For example, you can view the table of +originators (mesh participants) with: + +# cat /sys/class/net/bat0/mesh/originators + +Other files allow to change batman's behaviour to better fit your +requirements. For instance, you can check the current originator +interval (value in milliseconds which determines how often batman +sends its broadcast packets): + +# cat /sys/class/net/bat0/mesh/orig_interval +# status: 1000 + +and also change its value: + +# echo 3000 > /sys/class/net/bat0/mesh/orig_interval -The raw format consists of comma seperated values per entry where each -entry is giving information about a certain source interface. Each entry -can/has to have the following values: --> "mac" -> mac address of an originator's source interface - (each line begins with it) --> "TQ mac value" -> src mac's link quality towards mac address of a neighbor - originator's interface which is being used for routing --> "HNA mac" -> HNA announced by source mac --> "PRIMARY" -> this is a primary interface --> "SEC mac" -> secondary mac address of source (requires preceeding --> PRIMARY) - -The TQ value has a range from 4 to 255 with 255 being the best. -The HNA entries are showing which hosts are connected to the mesh via bat0 -or being bridged into the mesh network. -The PRIMARY/SEC values are only applied on primary interfaces - ---- In very mobile scenarios, you might want to adjust the originator -interval to a lower value. This will make the mesh more responsive to -topology changes, but will also increase the overhead. Please make sure -that all nodes in your mesh use the same interval. The default value -is 1000 ms (1 second). +interval to a lower value. This will make the mesh more respon- +sive to topology changes, but will also increase the overhead. + + +USAGE +----- + +To make use of your newly created mesh, batman advanced provides +a new interface "bat0" which you should use from this point on. +All interfaces added to batman advanced are not relevant any +longer because batman handles them for you. Basically, one "hands +over" the data by using the batman interface and batman will make +sure it reaches its destination. -# echo 1000 > /proc/net/batman-adv/orig_interval +The "bat0" interface can be used like any other regular inter- +face. It needs an IP address which can be either statically con- +figured or dynamically (by using DHCP or similar services): -To deactivate batman, do: +# NodeA: ifconfig bat0 192.168.0.1 +# NodeB: ifconfig bat0 192.168.0.2 +# NodeB: ping 192.168.0.1 + +Note: In order to avoid problems remove all IP addresses previ- +ously assigned to interfaces now used by batman advanced, e.g. + +# ifconfig eth0 0.0.0.0 + + +VISUALIZATION +------------- + +If you want topology visualization, at least one mesh node must +be configured as VIS-server: + +# echo "server" > /sys/class/net/bat0/mesh/vis_mode + +Each node is either configured as "server" or as "client" (de- +fault: "client"). Clients send their topology data to the server +next to them, and server synchronize with other servers. If there +is no server configured (default) within the mesh, no topology +information will be transmitted. With these "synchronizing +servers", there can be 1 or more vis servers sharing the same (or +at least very similar) data. + +When configured as server, you can get a topology snapshot of +your mesh: + +# cat /sys/class/net/bat0/mesh/vis_data + +This raw output is intended to be easily parsable and convertable +with other tools. Have a look at the batctl README if you want a +vis output in dot or json format for instance and how those out- +puts could then be visualised in an image. + +The raw format consists of comma separated values per entry where +each entry is giving information about a certain source inter- +face. Each entry can/has to have the following values: +-> "mac" - mac address of an originator's source interface + (each line begins with it) +-> "TQ mac value" - src mac's link quality towards mac address + of a neighbor originator's interface which + is being used for routing +-> "HNA mac" - HNA announced by source mac +-> "PRIMARY" - this is a primary interface +-> "SEC mac" - secondary mac address of source + (requires preceding PRIMARY) + +The TQ value has a range from 4 to 255 with 255 being the best. +The HNA entries are showing which hosts are connected to the mesh +via bat0 or being bridged into the mesh network. The PRIMARY/SEC +values are only applied on primary interfaces -# echo "" > /proc/net/batman-adv/interfaces LOGGING/DEBUGGING ----------------- -All error messages, warnings and information messages are sent to the -kernel log. Depending on your operating system distribution this can be -read in one of a number of ways. Try using the commands: dmesg, -logread, or looking in the files /var/log/kern.log or -/var/log/syslog. All batman-adv messages are prefixed with +All error messages, warnings and information messages are sent to +the kernel log. Depending on your operating system distribution +this can be read in one of a number of ways. Try using the com- +mands: dmesg, logread, or looking in the files /var/log/kern.log +or /var/log/syslog. All batman-adv messages are prefixed with "batman-adv:" So to see just these messages try -dmesg | grep batman-adv +# dmesg | grep batman-adv -When investigating problems with your mesh network it is sometimes -necessary to see more detail debug messages. This must be enabled when -compiling the batman-adv module. Use "make menuconfig" and enable the +When investigating problems with your mesh network it is some- +times necessary to see more detail debug messages. This must be +enabled when compiling the batman-adv module. When building bat- +man-adv as part of kernel, use "make menuconfig" and enable the option "B.A.T.M.A.N. debugging". -The additional debug output is by default disabled. It can be enabled -either at kernel module load time or during run time. To enable debug -output at module load time, add the module parameter debug=<value>. -<value> can take one of four values. +The additional debug output is by default disabled. It can be en- +abled either at kernel modules load time or during run time. To +enable debug output at module load time, add the module parameter +debug=<value>. <value> can take one of four values. -0 - All debug output disabled +0 - All debug output disabled 1 - Enable messages related to routing / flooding / broadcasting 2 - Enable route or hna added / changed / deleted 3 - Enable all messages e.g. -modprobe batman-adv debug=2 +# modprobe batman-adv debug=2 -will load the module and enable debug messages for when routes or HNAs -change. +will load the module and enable debug messages for when routes or +HNAs change. -The debug output can also be changed at runtime using the file +The debug output can also be changed at runtime using the file /sys/module/batman-adv/parameters/debug. e.g. -echo 2 > /sys/module/batman-adv/parameters/debug +# echo 2 > /sys/module/batman-adv/parameters/debug enables debug messages for when routes or HNAs -The debug output is sent to the kernel logs. So try dmesg, logread etc -to see the debug messages. +The debug output is sent to the kernel logs. So try dmesg, lo- +gread, etc to see the debug messages. + BATCTL ------ -B.A.T.M.A.N. advanced operates on layer 2 and thus all hosts -participating in the virtual switch are completely transparent for all -protocols above layer 2. Therefore the common diagnosis tools do not -work as expected. To overcome these problems batctl was created. At -the moment the batctl contains ping, traceroute, tcpdump and +As batman advanced operates on layer 2 all hosts participating in +the virtual switch are completely transparent for all protocols +above layer 2. Therefore the common diagnosis tools do not work +as expected. To overcome these problems batctl was created. At +the moment the batctl contains ping, traceroute, tcpdump and interfaces to the kernel module settings. For more information, please see the manpage (man batctl). -batctl is available on http://www.open-mesh.net/ +batctl is available on http://www.open-mesh.org/ + CONTACT ------- Please send us comments, experiences, questions, anything :) -IRC: #batman on irc.freenode.org -Mailing-list: b.a.t.m.a.n@xxxxxxxxxxxxx -(subscription at https://list.open-mesh.net/mm/listinfo/b.a.t.m.a.n ) +IRC: #batman on irc.freenode.org +Mailing-list: b.a.t.m.a.n@xxxxxxxxxxxxx (optional subscription + at https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n) You can also contact the Authors: -Marek Lindner <lindner_marek@xxxxxxxx> -Simon Wunderlich <siwu@xxxxxxxxxxxxxxxxxx> +Marek Lindner <lindner_marek@xxxxxxxx> +Simon Wunderlich <siwu@xxxxxxxxxxxxxxxxxx> + -- 1.7.0.3 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
