This is a new Kconfig and Makefikes for staging/comedi. The drivers are sorted now alphabetically in sub-menus depending on the bustype. I did some basiy dependancy tests, but there still may be a lot that I missed. >From c53596606230a4a8ee7dd76b48cf6b10a059e8f7 Mon Sep 17 00:00:00 2001 From: Alexander Kurz <linux@xxxxxxxxxxxx> Date: Fri, 7 May 2010 22:46:17 +0200 Subject: [PATCH] staging/comedi: new Kconfig and Makefiles, drivers grouped by bustype. PC/104-drivers went into ISA, PC/104+ went into PCI, Drivers without a bustype went into "misc". In doubt drivers supporting both ISA/PCI went into PCI. Drivers without any detailed hardware info went into ISA, e.g. fl512.c Some NI drivers are used by other NI drivers from different bustypes are grouped seperately in NI_COMMON. Signed-off-by: Alexander Kurz <linux@xxxxxxxxxxxx> --- drivers/staging/comedi/Kconfig | 1274 +++++++++++++++++++++++++++- drivers/staging/comedi/drivers/Makefile | 245 +++--- drivers/staging/comedi/kcomedilib/Makefile | 2 +- 3 files changed, 1392 insertions(+), 129 deletions(-) diff --git a/drivers/staging/comedi/Kconfig b/drivers/staging/comedi/Kconfig index d63c889..e9ce9c8 100644 --- a/drivers/staging/comedi/Kconfig +++ b/drivers/staging/comedi/Kconfig @@ -9,27 +9,1287 @@ config COMEDI config COMEDI_DEBUG bool "Comedi debugging" depends on COMEDI != n - help + ---help--- This is an option for use by developers; most people should say N here. This enables comedi core and driver debugging. -config COMEDI_PCI_DRIVERS +menuconfig COMEDI_MISC_DRIVERS + tristate "Comedi misc drivers" + depends on COMEDI + default N + ---help--- + Enable comedi misc drivers to be built + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about misc non-hardware comedi drivers. + +if COMEDI_MISC_DRIVERS + +config COMEDI_KCOMEDILIB + tristate "Comedi kcomedilib" + ---help--- + Build the kcomedilib + +config COMEDI_BOND + tristate "Device bonding support" + depends on COMEDI_KCOMEDILIB + default N + ---help--- + Enable support for a driver to 'bond' (merge) multiple subdevices + from multiple devices together as one. + + To compile this driver as a module, choose M here: the module will be + called comedi_bond. + +config COMEDI_TEST + tristate "Fake waveform generator support" + select COMEDI_FC + default N + ---help--- + Enable support for the fake waveform generator. + This driver is mainly for testing purposes, but can also be used to + generate sample waveforms on systems that don't have data acquisition + hardware. + + To compile this driver as a module, choose M here: the module will be + called comedi_test. + +config COMEDI_PARPORT + tristate "Parallel port support" + depends on PARPORT_PC + default N + ---help--- + Enable support for the standard parallel port. + A cheap and easy way to get a few more digital I/O lines. Steal + additional parallel ports from old computers or your neighbors' + computers. + + To compile this driver as a module, choose M here: the module will be + called comedi_parport. + +config COMEDI_SERIAL2002 + tristate "Driver for serial connected hardware" + default N + ---help--- + Enable support for serial connected hardware + + To compile this driver as a module, choose M here: the module will be + called serial2002. + +config COMEDI_SKEL + tristate "Comedi skeleton driver" + default N + ---help--- + Build the Skeleton driver, an example for driver writers + + To compile this driver as a module, choose M here: the module will be + called skel. + +endif # COMEDI_MISC_DRIVERS + +menuconfig COMEDI_ISA_DRIVERS + tristate "Comedi ISA and PC/104 drivers" + depends on COMEDI && ISA + default N + ---help--- + Enable comedi ISA and PC/104 drivers to be built + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about ISA and PC/104 comedi drivers. + +if COMEDI_ISA_DRIVERS && ISA + +config COMEDI_8255 + tristate "Generic 8255 support" + default N + ---help--- + Enable generic 8255 support. + + To compile this driver as a module, choose M here: the module will be + called 8255. + +config COMEDI_ACL7225B + tristate "ADlink NuDAQ ACL-7225b and compatibles support" + default N + ---help--- + Enable support for ADlink NuDAQ ACL-7225b and compatibles, + ADlink ACL-7225b (acl7225b), ICP P16R16DIO (p16r16dio) + + To compile this driver as a module, choose M here: the module will be + called acl7225b. + +config COMEDI_PCL711 + tristate "Advantech PCL-711/711b and ADlink ACL-8112 ISA card support" + default N + ---help--- + Enable support for Advantech PCL-711 and 711b, ADlink ACL-8112 + + To compile this driver as a module, choose M here: the module will be + called pcl711. + +config COMEDI_PCL724 + tristate "Advantech PCL-722/724/731 and ADlink ACL-7122/7124/PET-48DIO" + default N + ---help--- + Enable support for Advantech PCL-724, PCL-722, PCL-731 and + ADlink ACL-7122, ACL-7124, PET-48DIO ISA cards + + To compile this driver as a module, choose M here: the module will be + called pcl724. + +config COMEDI_PCL725 + tristate "Advantech PCL-725 and compatible ISA card support" + default N + ---help--- + Enable support for Advantech PCL-725 and compatible ISA cards. + + To compile this driver as a module, choose M here: the module will be + called pcl725. + +config COMEDI_PCL726 + tristate "Advantech PCL-726 and compatible ISA card support" + default N + ---help--- + Enable support for Advantech PCL-726 and compatible ISA cards. + + To compile this driver as a module, choose M here: the module will be + called pcl726. + +config COMEDI_PCL730 + tristate "Advantech PCL-730 and ADlink ACL-7130 ISA card support" + default N + ---help--- + Enable support for Advantech PCL-730, ICP ISO-730 and ADlink + ACL-7130 ISA cards + + To compile this driver as a module, choose M here: the module will be + called pcl730. + +config COMEDI_PCL812 + tristate "Advantech PCL-812/813 and ADlink ACL-8112/8113/8113/8216" + default N + ---help--- + Enable support for Advantech PCL-812/PG, PCL-813/B, ADLink + ACL-8112DG/HG/PG, ACL-8113, ACL-8216, ICP DAS A-821PGH/PGL/PGL-NDA, + A-822PGH/PGL, A-823PGH/PGL, A-826PG and ICP DAS ISO-813 ISA cards + + To compile this driver as a module, choose M here: the module will be + called pcl812. + +config COMEDI_PCL816 + tristate "Advantech PCL-814 and PCL-816 ISA card support" + default N + ---help--- + Enable support for Advantech PCL-814 and PCL-816 ISA cards + + To compile this driver as a module, choose M here: the module will be + called pcl816. + +config COMEDI_PCL818 + tristate "Advantech PCL-718 and PCL-818 ISA card support" + default N + ---help--- + Enable support for Advantech PCL-818 ISA cards + PCL-818L, PCL-818H, PCL-818HD, PCL-818HG, PCL-818 and PCL-718 + + To compile this driver as a module, choose M here: the module will be + called pcl818. + +config COMEDI_PCM3724 + tristate "Advantech PCM-3724 PC/104 card support" + default N + ---help--- + Enable support for Advantech PCM-3724 PC/104 cards. + + To compile this driver as a module, choose M here: the module will be + called pcm3724. + +config COMEDI_PCM3730 + tristate "Advantech PCM-3730 and clone PC/104 board support" + default N + ---help--- + Enable support for Advantech PCM-3730 and clone PC/104 boards + + To compile this driver as a module, choose M here: the module will be + called pcm3730. + +config COMEDI_RTI800 + tristate "Analog Devices RTI-800/815 ISA card support" + default N + ---help--- + Enable support for Analog Devices RTI-800/815 ISA cards + + To compile this driver as a module, choose M here: the module will be + called rti800. + +config COMEDI_RTI802 + tristate "Analog Devices RTI-802 ISA card support" + default N + ---help--- + Enable support for Analog Devices RTI-802 ISA cards + + To compile this driver as a module, choose M here: the module will be + called rti802. + +config COMEDI_DAS08 + tristate "DAS-08 compatible ISA, PC/104 and PCMCIA card support" + default N + ---help--- + Enable support for Keithley Metrabyte/ComputerBoards DAS08 + and compatible ISA and PC/104 cards + + To compile this driver as a module, choose M here: the module will be + called das08. + +config COMEDI_DAS16M1 + tristate "MeasurementComputing CIO-DAS16/M1DAS-16 ISA card support" + select COMEDI_FC + default N + ---help--- + Enable support for Measurement Computing CIO-DAS16/M1 ISA cards. + + To compile this driver as a module, choose M here: the module will be + called das16m1. + +config COMEDI_DAS16 + tristate "DAS-16 compatible ISA and PC/104 card support" + select COMEDI_FC + default N + ---help--- + Enable support for Keithley Metrabyte/ComputerBoards DAS16 + and compatible ISA and PC/104 cards: + Keithley Metrabyte DAS-16, DAS-16G, DAS-16F, DAS-1201, DAS-1202, + DAS-1401, DAS-1402, DAS-1601, DAS-1602 and + ComputerBoards/MeasurementComputing PC104-DAS16/JR/, + PC104-DAS16JR/16, CIO-DAS16JR/16, CIO-DAS16/JR, CIO-DAS1401/12, + CIO-DAS1402/12, CIO-DAS1402/16, CIO-DAS1601/12, CIO-DAS1602/12, + CIO-DAS1602/16, CIO-DAS16/330 + + To compile this driver as a module, choose M here: the module will be + called das16. + +config COMEDI_DAS800 + tristate "DAS800 and compatible ISA card support" + select COMEDI_FC + default N + ---help--- + Enable support for Keithley Metrabyte DAS800 and compatible ISA cards + Keithley Metrabyte DAS-800, DAS-801, DAS-802 + Measurement Computing CIO-DAS800, CIO-DAS801, CIO-DAS802 and + CIO-DAS802/16 + + To compile this driver as a module, choose M here: the module will be + called das800. + +config COMEDI_DAS1800 + tristate "DAS1800 and compatible ISA card support" + select COMEDI_FC + default N + ---help--- + Enable support for DAS1800 and compatible ISA cards + Keithley Metrabyte DAS-1701ST, DAS-1701ST-DA, DAS-1701/AO, + DAS-1702ST, DAS-1702ST-DA, DAS-1702HR, DAS-1702HR-DA, DAS-1702/AO, + DAS-1801ST, DAS-1801ST-DA, DAS-1801HC, DAS-1801AO, DAS-1802ST, + DAS-1802ST-DA, DAS-1802HR, DAS-1802HR-DA, DAS-1802HC and + DAS-1802AO + + To compile this driver as a module, choose M here: the module will be + called das1800. + +config COMEDI_DAS6402 + tristate "DAS6402 and compatible ISA card support" + default N + ---help--- + Enable support for DAS6402 and compatible ISA cards + Computerboards, Keithley Metrabyte DAS6402 and compatibles + + To compile this driver as a module, choose M here: the module will be + called das6402. + +config COMEDI_DT2801 + tristate "Data Translation DT2801 ISA card support" + default N + ---help--- + Enable support for Data Translation DT2801 ISA cards + + To compile this driver as a module, choose M here: the module will be + called dt2801. + +config COMEDI_DT2811 + tristate "Data Translation DT2811 ISA card support" + default N + ---help--- + Enable support for Data Translation DT2811 ISA cards + + To compile this driver as a module, choose M here: the module will be + called dt2811. + +config COMEDI_DT2814 + tristate "Data Translation DT2814 ISA card support" + default N + ---help--- + Enable support for Data Translation DT2814 ISA cards + + To compile this driver as a module, choose M here: the module will be + called dt2814. + +config COMEDI_DT2815 + tristate "Data Translation DT2815 ISA card support" + default N + ---help--- + Enable support for Data Translation DT2815 ISA cards + + To compile this driver as a module, choose M here: the module will be + called dt2815. + +config COMEDI_DT2817 + tristate "Data Translation DT2817 ISA card support" + default N + ---help--- + Enable support for Data Translation DT2817 ISA cards + + To compile this driver as a module, choose M here: the module will be + called dt2817. + +config COMEDI_DT282X + tristate "Data Translation DT2821 series and DT-EZ ISA card support" + select COMEDI_FC + default N + ---help--- + Enable support for Data Translation DT2821 series including DT-EZ + DT2821, DT2821-F-16SE, DT2821-F-8DI, DT2821-G-16SE, DT2821-G-8DI, + DT2823 (dt2823), DT2824-PGH, DT2824-PGL, DT2825, DT2827, DT2828, + DT21-EZ, DT23-EZ, DT24-EZ and DT24-EZ-PGL + + To compile this driver as a module, choose M here: the module will be + called dt282x. + +config COMEDI_DMM32AT + tristate "Diamond Systems MM-32-AT PC/104 board support" + default N + ---help--- + Enable support for Diamond Systems MM-32-AT PC/104 boards + + To compile this driver as a module, choose M here: the module will be + called dmm32at. + +config COMEDI_FL512 + tristate "FL512 ISA card support" + default N + ---help--- + Enable support for FL512 ISA card + + To compile this driver as a module, choose M here: the module will be + called fl512. + +config COMEDI_AIO_AIO12_8 + tristate "I/O Products PC/104 AIO12-8 Analog I/O Board support" + default N + ---help--- + Enable support for I/O Products PC/104 AIO12-8 Analog I/O Board + + To compile this driver as a module, choose M here: the module will be + called aio_aio12_8. + +config COMEDI_AIO_IIRO_16 + tristate "I/O Products PC/104 IIRO16 Board support" + default N + ---help--- + Enable support for I/O Products PC/104 IIRO16 Relay And Isolated + Input Board + + To compile this driver as a module, choose M here: the module will be + called aio_iiro_16. + +config COMEDI_C6XDIGIO + tristate "Mechatronic Systems Inc. C6x_DIGIO DSP daughter card support" + default N + ---help--- + Enable support for Mechatronic Systems Inc. C6x_DIGIO DSP daughter + card + + To compile this driver as a module, choose M here: the module will be + called c6xdigio. + +config COMEDI_MPC624 + tristate "Micro/sys MPC-624 PC/104 board support" + default N + ---help--- + Enable support for Micro/sys MPC-624 PC/104 board + + To compile this driver as a module, choose M here: the module will be + called mpc624. + +config COMEDI_ADQ12B + tristate "MicroAxial ADQ12-B data acquisition and control card support" + default N + ---help--- + Enable MicroAxial ADQ12-B daq and control card support. + + To compile this driver as a module, choose M here: the module will be + called adq12b. + +config COMEDI_NI_AT_A2150 + tristate "NI AT-A2150 ISA card support" + depends on COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments AT-A2150 cards + + To compile this driver as a module, choose M here: the module will be + called ni_at_a2150. + +config COMEDI_NI_AT_AO + tristate "NI AT-AO-6/10 EISA card support" + depends on COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments AT-AO-6/10 cards + + To compile this driver as a module, choose M here: the module will be + called ni_at_ao. + +config COMEDI_NI_ATMIO + tristate "NI AT-MIO E series ISA-PNP card support" + depends on ISAPNP && COMEDI_NI_TIO && COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments AT-MIO E series cards + National Instruments AT-MIO-16E-1 (ni_atmio), + AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3, + AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10 + + To compile this driver as a module, choose M here: the module will be + called ni_atmio. + +config COMEDI_NI_ATMIO16D + tristate "NI AT-MIO16/AT-MIO16D series ISA-PNP card support" + depends on ISAPNP && COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments AT-MIO16/AT-MIO16D cards. + + To compile this driver as a module, choose M here: the module will be + called ni_atmio16d. + +config COMEDI_PCMAD + tristate "Winsystems PCM-A/D12 and PCM-A/D16 PC/104 board support" + default N + ---help--- + Enable support for Winsystems PCM-A/D12 and PCM-A/D16 PC/104 boards. + + To compile this driver as a module, choose M here: the module will be + called pcmad. + +config COMEDI_PCMDA12 + tristate "Winsystems PCM-D/A-12 8-channel AO PC/104 board support" + default N + ---help--- + Enable support for Winsystems PCM-D/A-12 8-channel AO PC/104 boards. + Note that the board is not ISA-PNP capable and thus needs the I/O + port comedi_config parameter. + + To compile this driver as a module, choose M here: the module will be + called pcmda12. + +config COMEDI_PCMMIO + tristate "Winsystems PCM-MIO PC/104 board support" + default N + ---help--- + Enable support for Winsystems PCM-MIO multifunction PC/104 boards. + + To compile this driver as a module, choose M here: the module will be + called pcmmio. + +config COMEDI_PCMUIO + tristate "Winsystems PCM-UIO48A and PCM-UIO96A PC/104 board support" + default N + ---help--- + Enable support for PCM-UIO48A and PCM-UIO96A PC/104 boards. + + To compile this driver as a module, choose M here: the module will be + called pcmuio. + +config COMEDI_MULTIQ3 + tristate "Quanser Consulting MultiQ-3 ISA card support" + default N + ---help--- + Enable support for Quanser Consulting MultiQ-3 ISA cards + + To compile this driver as a module, choose M here: the module will be + called multiq3. + +config COMEDI_POC + tristate "Generic driver for very simple devices" + default N + ---help--- + Enable generic support for very simple / POC (Piece of Crap) boards, + Keithley Metrabyte DAC-02 (dac02), Advantech PCL-733 (pcl733) and + PCL-734 (pcl734) + + To compile this driver as a module, choose M here: the module will be + called poc. + +endif # COMEDI_ISA_DRIVERS + +menuconfig COMEDI_PCI_DRIVERS tristate "Comedi PCI drivers" depends on COMEDI && PCI default N ---help--- - Enable lots of comedi PCI drivers to be built + Enable comedi PCI drivers to be built + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about PCI comedi drivers. + +if COMEDI_PCI_DRIVERS && PCI + +config COMEDI_ADDI_APCI_035 + tristate "ADDI-DATA APCI_035 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_035 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_035. + +config COMEDI_ADDI_APCI_1032 + tristate "ADDI-DATA APCI_1032 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_1032 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_1032. + +config COMEDI_ADDI_APCI_1500 + tristate "ADDI-DATA APCI_1500 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_1500 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_1500. + +config COMEDI_ADDI_APCI_1516 + tristate "ADDI-DATA APCI_1516 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_1516 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_1516. + +config COMEDI_ADDI_APCI_1564 + tristate "ADDI-DATA APCI_1564 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_1564 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_1564. + +config COMEDI_ADDI_APCI_16XX + tristate "ADDI-DATA APCI_16xx support" + default N + ---help--- + Enable support for ADDI-DATA APCI_16xx cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_16xx. + +config COMEDI_ADDI_APCI_2016 + tristate "ADDI-DATA APCI_2016 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_2016 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_2016. + +config COMEDI_ADDI_APCI_2032 + tristate "ADDI-DATA APCI_2032 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_2032 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_2032. + +config COMEDI_ADDI_APCI_2200 + tristate "ADDI-DATA APCI_2200 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_2200 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_2200. + +config COMEDI_ADDI_APCI_3001 + tristate "ADDI-DATA APCI_3001 support" + select COMEDI_FC + default N + ---help--- + Enable support for ADDI-DATA APCI_3001 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_3001. + +config COMEDI_ADDI_APCI_3120 + tristate "ADDI-DATA APCI_3520 support" + select COMEDI_FC + default N + ---help--- + Enable support for ADDI-DATA APCI_3520 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_3120. + +config COMEDI_ADDI_APCI_3501 + tristate "ADDI-DATA APCI_3501 support" + default N + ---help--- + Enable support for ADDI-DATA APCI_3501 cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_3501. + +config COMEDI_ADDI_APCI_3XXX + tristate "ADDI-DATA APCI_3xxx support" + default N + ---help--- + Enable support for ADDI-DATA APCI_3xxx cards + + To compile this driver as a module, choose M here: the module will be + called addi_apci_3xxx. + +config COMEDI_ADL_PCI6208 + tristate "ADLink PCI-6208A support" + default N + ---help--- + Enable support for ADLink PCI-6208A cards + + To compile this driver as a module, choose M here: the module will be + called adl_pci6208. + +config COMEDI_ADL_PCI7296 + tristate "ADLink PCI-7296 96 ch. digital io board support" + default N + ---help--- + Enable support for ADlink PCI-7296 96 ch. digital io board support + + To compile this driver as a module, choose M here: the module will be + called adl_pci7296. + +config COMEDI_ADL_PCI7432 + tristate "ADLink PCI-7432 64 ch. isolated digital io board support" + default N + ---help--- + Enable support for ADlink PCI-7432 64 ch. isolated digital io board + + To compile this driver as a module, choose M here: the module will be + called adl_pci7432. + +config COMEDI_ADL_PCI8164 + tristate "ADLink PCI-8164 4 Axes Motion Control board support" + default N + ---help--- + Enable support for ADlink PCI-8164 4 Axes Motion Control board + + To compile this driver as a module, choose M here: the module will be + called adl_pci8164. + +config COMEDI_ADL_PCI9111 + tristate "ADLink PCI-9111HR support" + select COMEDI_FC + default N + ---help--- + Enable support for ADlink PCI9111 cards + + To compile this driver as a module, choose M here: the module will be + called adl_pci9111. + +config COMEDI_ADL_PCI9118 + tristate "ADLink PCI-9118DG, PCI-9118HG, PCI-9118HR support" + select COMEDI_FC + default N + ---help--- + Enable support for ADlink PCI-9118DG, PCI-9118HG, PCI-9118HR cards + + To compile this driver as a module, choose M here: the module will be + called adl_pci9118. + +config COMEDI_ADV_PCI1710 + tristate "Advantech PCI-171x, PCI-1720 and PCI-1731 support" + default N + ---help--- + Enable support for Advantech PCI-1710, PCI-1710HG, PCI-1711, + PCI-1713, PCI-1720 and PCI-1731 + + To compile this driver as a module, choose M here: the module will be + called adv_pci1710. + +config COMEDI_ADV_PCI1723 + tristate "Advantech PCI-1723 support" + default N + ---help--- + Enable support for Advantech PCI-1723 cards + + To compile this driver as a module, choose M here: the module will be + called adv_pci1723. + +config COMEDI_ADV_PCI_DIO + tristate "Advantech PCI DIO card support" + default N + ---help--- + Enable support for Advantech PCI DIO cards + PCI-1730, PCI-1733, PCI-1734, PCI-1736UP, PCI-1750, PCI-1751, + PCI-1752, PCI-1753/E, PCI-1754, PCI-1756 and PCI-1762 + + To compile this driver as a module, choose M here: the module will be + called adv_pci_dio. + +config COMEDI_AMPLC_DIO200 + tristate "Amplicon PC272E and PCI272 DIO board support" + default N + ---help--- + Enable support for Amplicon PC272E and PCI272 DIO boards + + To compile this driver as a module, choose M here: the module will be + called amplc_dio200. + +config COMEDI_AMPLC_PC236 + tristate "Amplicon PC36AT and PCI236 DIO board support" + default N + ---help--- + Enable support for Amplicon PC36AT and PCI236 DIO boards + + To compile this driver as a module, choose M here: the module will be + called amplc_pc236. + +config COMEDI_AMPLC_PC263 + tristate "Amplicon PC263 and PCI263 relay board support" + default N + ---help--- + Enable support for Amplicon PC263 and PCI263 relay boards + + To compile this driver as a module, choose M here: the module will be + called amplc_pc263. + +config COMEDI_AMPLC_PCI224 + tristate "Amplicon PCI224 and PCI234 support" + select COMEDI_FC + default N + ---help--- + Enable support for Amplicon PCI224 and PCI234 AO boards -config COMEDI_PCMCIA_DRIVERS + To compile this driver as a module, choose M here: the module will be + called amplc_pci224. + +config COMEDI_AMPLC_PCI230 + tristate "Amplicon PCI230 and PCI260 support" + default N + ---help--- + Enable support for Amplicon PCI230 and PCI260 Multifunction I/O + boards + + To compile this driver as a module, choose M here: the module will be + called amplc_pci230. + +config COMEDI_CONTEC_PCI_DIO + tristate "Contec PIO1616L digital I/O board support" + default N + ---help--- + Enable support for the Contec PIO1616L digital I/O board + + To compile this driver as a module, choose M here: the module will be + called contec_pci_dio. + +config COMEDI_DT3000 + tristate "Data Translation DT3000 series support" + default N + ---help--- + Enable support for Data Translation DT3000 series + DT3001, DT3001-PGL, DT3002, DT3003, DT3003-PGL, DT3004, DT3005 and + DT3004-200 + + To compile this driver as a module, choose M here: the module will be + called dt3000. + +config COMEDI_UNIOXX5 + tristate "Fastwel UNIOxx-5 analog and digital io board support" + default N + ---help--- + Enable support for Fastwel UNIOxx-5 (analog and digital i/o) boards + + To compile this driver as a module, choose M here: the module will be + called unioxx5. + +config COMEDI_GSC_HPDI + tristate "General Standards PCI-HPDI32 / PMC-HPDI32 support" + select COMEDI_FC + default N + ---help--- + Enable support for General Standards Corporation high speed parallel + digital interface rs485 boards PCI-HPDI32 and PMC-HPDI32. + Only receive mode works, transmit not supported. + + To compile this driver as a module, choose M here: the module will be + called gsc_hpdi. + +config COMEDI_ICP_MULTI + tristate "Inova ICP_MULTI support" + default N + ---help--- + Enable support for Inova ICP_MULTI card + + To compile this driver as a module, choose M here: the module will be + called icp_multi. + +config COMEDI_II_PCI20KC + tristate "Intelligent Instruments PCI-20001C carrier support" + default N + ---help--- + Enable support for Intelligent Instruments PCI-20001C carrier + PCI-20001, PCI-20006 and PCI-20341 + + To compile this driver as a module, choose M here: the module will be + called ii_pci20kc. + +config COMEDI_DAQBOARD2000 + tristate "IOtech DAQboard/2000 support" + default N + ---help--- + Enable support for the IOtech DAQboard/2000 + + To compile this driver as a module, choose M here: the module will be + called daqboard2000. + +config COMEDI_JR3_PCI + tristate "JR3/PCI force sensor board support" + default N + ---help--- + Enable support for JR3/PCI force sensor boards + + To compile this driver as a module, choose M here: the module will be + called jr3_pci. + +config COMEDI_KE_COUNTER + tristate "Kolter-Electronic PCI Counter 1 card support" + default N + ---help--- + Enable support for Kolter-Electronic PCI Counter 1 cards + + To compile this driver as a module, choose M here: the module will be + called ke_counter. + +config COMEDI_CB_PCIDAS64 + tristate "MeasurementComputing PCI-DAS 64xx, 60xx, and 4020 support" + select COMEDI_FC + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCI-DAS 64xx, + 60xx, and 4020 series with the PLX 9080 PCI controller + + To compile this driver as a module, choose M here: the module will be + called cb_pcidas64. + +config COMEDI_CB_PCIDAS + tristate "MeasurementComputing PCI-DAS support" + select COMEDI_FC + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCI-DAS with + AMCC S5933 PCIcontroller: PCI-DAS1602/16, PCI-DAS1602/16jr, + PCI-DAS1602/12, PCI-DAS1200, PCI-DAS1200jr, PCI-DAS1000, PCI-DAS1001 + and PCI_DAS1002. + + To compile this driver as a module, choose M here: the module will be + called cb_pcidas. + +config COMEDI_CB_PCIDDA + tristate "MeasurementComputing PCI-DDA series support" + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCI-DDA + series: PCI-DDA08/12, PCI-DDA04/12, PCI-DDA02/12, PCI-DDA08/16, + PCI-DDA04/16 and PCI-DDA02/16 + + To compile this driver as a module, choose M here: the module will be + called cb_pcidda. + +config COMEDI_CB_PCIDIO + tristate "MeasurementComputing PCI-DIO series support" + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCI-DIO series + PCI-DIO24, PCI-DIO24H and PCI-DIO48H + + To compile this driver as a module, choose M here: the module will be + called cb_pcidio. + +config COMEDI_CB_PCIMDAS + tristate "MeasurementComputing PCIM-DAS1602/16 support" + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCI Migration + series PCIM-DAS1602/16 + + To compile this driver as a module, choose M here: the module will be + called cb_pcimdas. + +config COMEDI_CB_PCIMDDA + tristate "MeasurementComputing PCIM-DDA06-16 support" + default N + ---help--- + Enable support for ComputerBoards/MeasurementComputing PCIM-DDA06-16 + + To compile this driver as a module, choose M here: the module will be + called cb_pcimdda. + +config COMEDI_ME4000 + tristate "Meilhaus ME-4000 support" + default N + ---help--- + Enable support for Meilhaus PCI data acquisition cards + ME-4650, ME-4670i, ME-4680, ME-4680i and ME-4680is + + To compile this driver as a module, choose M here: the module will be + called me4000. + +config COMEDI_ME_DAQ + tristate "Meilhaus ME-2000i, ME-2600i, ME-3000vm1 support" + default N + ---help--- + Enable support for Meilhaus PCI data acquisition cards + ME-2000i, ME-2600i and ME-3000vm1 + + To compile this driver as a module, choose M here: the module will be + called me_daq. + +config COMEDI_NI_6527 + tristate "NI 6527 support" + depends on COMEDI_MITE + default N + ---help--- + Enable support for the National Instruments 6527 PCI card + + To compile this driver as a module, choose M here: the module will be + called ni_6527. + +config COMEDI_NI_65XX + tristate "NI 65xx static dio PCI card support" + depends on COMEDI_MITE + default N + ---help--- + Enable support for National Instruments 65xx static dio boards. + Supported devices: National Instruments PCI-6509 (ni_65xx), + PXI-6509, PCI-6510, PCI-6511, PXI-6511, PCI-6512, PXI-6512, PCI-6513, + PXI-6513, PCI-6514, PXI-6514, PCI-6515, PXI-6515, PCI-6516, PCI-6517, + PCI-6518, PCI-6519, PCI-6520, PCI-6521, PXI-6521, PCI-6528, PXI-6528 + + To compile this driver as a module, choose M here: the module will be + called ni_65xx. + +config COMEDI_NI_660X + tristate "NI 660x counter/timer PCI card support" + depends on COMEDI_NI_TIO && COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments PCI-6601 (ni_660x), PCI-6602, + PXI-6602 and PXI-6608. + + To compile this driver as a module, choose M here: the module will be + called ni_660x. + +config COMEDI_NI_670X + tristate "NI 670x PCI card support" + depends on COMEDI_MITE + default N + ---help--- + Enable support for National Instruments PCI-6703 and PCI-6704 + + To compile this driver as a module, choose M here: the module will be + called ni_670x. + +config COMEDI_NI_PCIDIO + tristate "NI PCI-DIO32HS, PCI-DIO96, PCI-6533, PCI-6503 support" + depends on COMEDI_MITE + default N + ---help--- + Enable support for National Instruments PCI-DIO-32HS, PXI-6533, + PCI-DIO-96, PCI-DIO-96B, PXI-6508, PCI-6503, PCI-6503B, PCI-6503X, + PXI-6503, PCI-6533 and PCI-6534 + The DIO-96 appears as four 8255 subdevices. See the 8255 + driver notes for details. + + To compile this driver as a module, choose M here: the module will be + called ni_pcidio. + +config COMEDI_NI_PCIMIO + tristate "NI PCI-MIO-E series and M series support" + depends on COMEDI_NI_TIO && COMEDI_NI_COMMON + default N + ---help--- + Enable support for National Instruments PCI-MIO-E series and M series + (all boards): PCI-MIO-16XE-10, PXI-6030E, PCI-MIO-16E-1, + PCI-MIO-16E-4, PCI-6014, PCI-6040E, PXI-6040E, PCI-6030E, PCI-6031E, + PCI-6032E, PCI-6033E, PCI-6071E, PCI-6023E, PCI-6024E, PCI-6025E, + PXI-6025E, PCI-6034E, PCI-6035E, PCI-6052E, PCI-6110, PCI-6111, + PCI-6220, PCI-6221, PCI-6224, PXI-6224, PCI-6225, PXI-6225, PCI-6229, + PCI-6250, PCI-6251, PCIe-6251, PCI-6254, PCI-6259, PCIe-6259, + PCI-6280, PCI-6281, PXI-6281, PCI-6284, PCI-6289, PCI-6711, PXI-6711, + PCI-6713, PXI-6713, PXI-6071E, PCI-6070E, PXI-6070E, PXI-6052E, + PCI-6036E, PCI-6731, PCI-6733, PXI-6733, PCI-6143, PXI-6143 + + To compile this driver as a module, choose M here: the module will be + called ni_pcimio. + +config COMEDI_RTD520 + tristate "Real Time Devices PCI4520/DM7520 support" + default N + ---help--- + Enable support for Real Time Devices PCI4520/DM7520 + + To compile this driver as a module, choose M here: the module will be + called rtd520. + +config COMEDI_S526 + tristate "Sensoray s526 support" + default N + ---help--- + Enable support for Sensoray s526 + + To compile this driver as a module, choose M here: the module will be + called s526. + +config COMEDI_S626 + tristate "Sensoray 626 support" + select COMEDI_FC + default N + ---help--- + Enable support for Sensoray 626 + + To compile this driver as a module, choose M here: the module will be + called s626. + +config COMEDI_SSV_DNP + tristate "SSV Embedded Systems DIL/Net-PC support" + default N + ---help--- + Enable support for SSV Embedded Systems DIL/Net-PC + + To compile this driver as a module, choose M here: the module will be + called ssv_dnp. + +endif # COMEDI_PCI_DRIVERS + +menuconfig COMEDI_PCMCIA_DRIVERS tristate "Comedi PCMCIA drivers" depends on COMEDI && PCMCIA && PCCARD default N ---help--- - Enable lots of comedi PCMCIA and PCCARD drivers to be built + Enable comedi PCMCIA and PCCARD drivers to be built + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about PCMCIA comedi drivers. + +if COMEDI_PCMCIA_DRIVERS && PCMCIA + +config COMEDI_CB_DAS16_CS + tristate "CB DAS16 series PCMCIA support" + default N + ---help--- + Enable support for the ComputerBoards/MeasurementComputing PCMCIA + cards DAS16/16, PCM-DAS16D/12 and PCM-DAS16s/16 + + To compile this driver as a module, choose M here: the module will be + called cb_das16_cs. + +config COMEDI_DAS08_CS + tristate "CB DAS08 PCMCIA support" + select COMEDI_DAS08 + default N + ---help--- + Enable support for the ComputerBoards/MeasurementComputing DAS-08 + PCMCIA card + + To compile this driver as a module, choose M here: the module will be + called das08_cs. + +config COMEDI_NI_DAQ_700_CS + tristate "NI DAQCard-700 PCMCIA support" + depends on COMEDI_NI_COMMON + default N + ---help--- + Enable support for the National Instruments PCMCIA DAQCard-700 DIO + + To compile this driver as a module, choose M here: the module will be + called ni_daq_700. + +config COMEDI_NI_DAQ_DIO24_CS + tristate "NI DAQ-Card DIO-24 PCMCIA support" + depends on COMEDI_NI_COMMON + default N + ---help--- + Enable support for the National Instruments PCMCIA DAQ-Card DIO-24 + + To compile this driver as a module, choose M here: the module will be + called ni_daq_dio24. + +config COMEDI_NI_LABPC_CS + tristate "NI DAQCard-1200 PCMCIA support" + depends on COMEDI_NI_LABPC + default N + ---help--- + Enable support for the National Instruments PCMCIA DAQCard-1200 + + To compile this driver as a module, choose M here: the module will be + called ni_labpc_cs. + +config COMEDI_NI_MIO_CS + tristate "NI DAQCard E series PCMCIA support" + depends on COMEDI_NI_TIO && COMEDI_NI_COMMON + default N + select COMEDI_FC + ---help--- + Enable support for the National Instruments PCMCIA DAQCard E series + DAQCard-ai-16xe-50, DAQCard-ai-16e-4, DAQCard-6062E, DAQCard-6024E + and DAQCard-6036E + + To compile this driver as a module, choose M here: the module will be + called ni_mio_cs. -config COMEDI_USB_DRIVERS +config COMEDI_QUATECH_DAQP_CS + tristate "Quatech DAQP PCMCIA data capture card support" + default N + ---help--- + Enable support for the Quatech DAQP PCMCIA data capture cards + DAQP-208 and DAQP-308 + + To compile this driver as a module, choose M here: the module will be + called quatech_daqp_cs. + +endif # COMEDI_PCMCIA_DRIVERS + +menuconfig COMEDI_USB_DRIVERS tristate "Comedi USB drivers" depends on COMEDI && USB default N ---help--- - Enable lots of comedi USB drivers to be built + Enable comedi USB drivers to be built + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about USB comedi drivers. + +if COMEDI_USB_DRIVERS && USB + +config COMEDI_DT9812 + tristate "DataTranslation DT9812 USB module support" + default N + ---help--- + Enable support for the Data Translation DT9812 USB module + + To compile this driver as a module, choose M here: the module will be + called dt9812. + +config COMEDI_USBDUX + tristate "ITL USBDUX support" + default N + ---help--- + Enable support for the University of Stirling USB DAQ and INCITE + Technology Limited driver + + To compile this driver as a module, choose M here: the module will be + called usbdux. + +config COMEDI_USBDUXFAST + tristate "ITL USB-DUXfast support" + select COMEDI_FC + default N + ---help--- + Enable support for the University of Stirling USB-DUXfast and INCITE + Technology Limited driver + + To compile this driver as a module, choose M here: the module will be + called usbduxfast. + +config COMEDI_VMK80XX + tristate "Velleman VM110/VM140 USB Board support" + default N + ---help--- + Build the Velleman USB Board Low-Level Driver supporting the + K8055/K8061 aka VM110/VM140 devices + + To compile this driver as a module, choose M here: the module will be + called vmk80xx. + +endif # COMEDI_USB_DRIVERS + +menuconfig COMEDI_NI_COMMON + tristate "Comedi National Instruments card support" + depends on COMEDI + default N + ---help--- + Enable comedi support for National Instruments cards. + Modules in this section are used by many comedi NI drivers. + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about National Instruments cards. + +if COMEDI_NI_COMMON + +config COMEDI_MITE + tristate "NI Mite PCI interface chip support" + depends on PCI + default N + ---help--- + Enable support for National Instruments Mite PCI interface chip + + To compile this driver as a module, choose M here: the module will be + called mite. + +config COMEDI_NI_TIO + tristate "NI general purpose counter support" + depends on COMEDI_MITE + default N + ---help--- + Enable support for National Instruments general purpose counters. + This module is not used directly by end-users. Rather, it + is used by other drivers (for example ni_660x and ni_pcimio) + to provide support for NI's general purpose counters. + + To compile this driver as a modules, choose M here: two modules will + be build: ni_tio and ni_tiocmd. + +config COMEDI_NI_LABPC + tristate "NI Lab-PC and compatibles ISA and PCI support" + select COMEDI_FC + default N + ---help--- + Enable support for National Instruments Lab-PC and compatibles + Lab-PC-1200, Lab-PC-1200AI, Lab-PC+ and PCI-1200. + Kernel-level ISA plug-and-play support for the lab-pc-1200 boards has + not yet been added to the driver. + + To compile this driver as a module, choose M here: the module will be + called ni_labpc. + +endif # COMEDI_NI_COMMON + +config COMEDI_FC + tristate "Comedi shared functions for low-level driver support" + default N + ---help--- + Enable support for shared functions for low-level drivers. + This module is not used directly by end-users. Rather, it + is used by many other comedi drivers. + + To compile this driver as a module, choose M here: the module will be + called comedi_fc. diff --git a/drivers/staging/comedi/drivers/Makefile b/drivers/staging/comedi/drivers/Makefile index df2854d..3880b5a 100644 --- a/drivers/staging/comedi/drivers/Makefile +++ b/drivers/staging/comedi/drivers/Makefile @@ -2,132 +2,135 @@ # # Comedi "helper" modules -obj-$(CONFIG_COMEDI) += comedi_fc.o -obj-$(CONFIG_COMEDI) += comedi_bond.o -obj-$(CONFIG_COMEDI) += comedi_test.o -obj-$(CONFIG_COMEDI) += comedi_parport.o obj-$(CONFIG_COMEDI) += pcm_common.o +# Comedi misc drivers +obj-$(CONFIG_COMEDI_BOND) += comedi_bond.o +obj-$(CONFIG_COMEDI_TEST) += comedi_test.o +obj-$(CONFIG_COMEDI_PARPORT) += comedi_parport.o +obj-$(CONFIG_COMEDI_SERIAL2002) += serial2002.o +obj-$(CONFIG_COMEDI_SKEL) += skel.o + +# Comedi ISA drivers +obj-$(CONFIG_COMEDI_8255) += 8255.o +obj-$(CONFIG_COMEDI_ACL7225B) += acl7225b.o +obj-$(CONFIG_COMEDI_PCL711) += pcl711.o +obj-$(CONFIG_COMEDI_PCL724) += pcl724.o +obj-$(CONFIG_COMEDI_PCL725) += pcl725.o +obj-$(CONFIG_COMEDI_PCL726) += pcl726.o +obj-$(CONFIG_COMEDI_PCL730) += pcl730.o +obj-$(CONFIG_COMEDI_PCL812) += pcl812.o +obj-$(CONFIG_COMEDI_PCL816) += pcl816.o +obj-$(CONFIG_COMEDI_PCL818) += pcl818.o +obj-$(CONFIG_COMEDI_PCM3724) += pcm3724.o +obj-$(CONFIG_COMEDI_PCM3730) += pcm3730.o +obj-$(CONFIG_COMEDI_RTI800) += rti800.o +obj-$(CONFIG_COMEDI_RTI802) += rti802.o +obj-$(CONFIG_COMEDI_DAS08) += das08.o +obj-$(CONFIG_COMEDI_DAS16M1) += das16m1.o +obj-$(CONFIG_COMEDI_DAS16) += das16.o +obj-$(CONFIG_COMEDI_DAS800) += das800.o +obj-$(CONFIG_COMEDI_DAS1800) += das1800.o +obj-$(CONFIG_COMEDI_DAS6402) += das6402.o +obj-$(CONFIG_COMEDI_DT2801) += dt2801.o +obj-$(CONFIG_COMEDI_DT2811) += dt2811.o +obj-$(CONFIG_COMEDI_DT2814) += dt2814.o +obj-$(CONFIG_COMEDI_DT2815) += dt2815.o +obj-$(CONFIG_COMEDI_DT2817) += dt2817.o +obj-$(CONFIG_COMEDI_DT282X) += dt282x.o +obj-$(CONFIG_COMEDI_DMM32AT) += dmm32at.o +obj-$(CONFIG_COMEDI_FL512) += fl512.o +obj-$(CONFIG_COMEDI_AIO_AIO12_8) += aio_aio12_8.o +obj-$(CONFIG_COMEDI_AIO_IIRO_16) += aio_iiro_16.o +obj-$(CONFIG_COMEDI_C6XDIGIO) += c6xdigio.o +obj-$(CONFIG_COMEDI_MPC624) += mpc624.o +obj-$(CONFIG_COMEDI_ADQ12B) += adq12b.o +obj-$(CONFIG_COMEDI_NI_AT_A2150) += ni_at_a2150.o +obj-$(CONFIG_COMEDI_NI_AT_AO) += ni_at_ao.o +obj-$(CONFIG_COMEDI_NI_ATMIO) += ni_atmio.o +obj-$(CONFIG_COMEDI_NI_ATMIO16D) += ni_atmio16d.o +obj-$(CONFIG_COMEDI_PCMAD) += pcmad.o +obj-$(CONFIG_COMEDI_PCMDA12) += pcmda12.o +obj-$(CONFIG_COMEDI_PCMMIO) += pcmmio.o +obj-$(CONFIG_COMEDI_PCMUIO) += pcmuio.o +obj-$(CONFIG_COMEDI_MULTIQ3) += multiq3.o +obj-$(CONFIG_COMEDI_POC) += poc.o + # Comedi PCI drivers -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += 8255.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += acl7225b.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_035.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_1032.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_1500.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_1516.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_1564.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_16xx.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_2016.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_2032.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_2200.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_3001.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_3120.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_3501.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += addi_apci_3xxx.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci6208.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci7296.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci7432.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci8164.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci9111.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adl_pci9118.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adq12b.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adv_pci1710.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adv_pci1723.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += adv_pci_dio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += aio_aio12_8.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += aio_iiro_16.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += amplc_dio200.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += amplc_pc236.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += amplc_pc263.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += amplc_pci224.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += amplc_pci230.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += c6xdigio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcidas64.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcidas.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcidda.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcidio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcimdas.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += cb_pcimdda.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += comedi_bond.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += comedi_parport.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += comedi_test.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += contec_pci_dio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += daqboard2000.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das08.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das16m1.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das16.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das1800.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das6402.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += das800.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dmm32at.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt2801.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt2811.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt2814.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt2815.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt2817.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt282x.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += dt3000.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += fl512.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += gsc_hpdi.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += icp_multi.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ii_pci20kc.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += jr3_pci.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ke_counter.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += me4000.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += me_daq.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += mite.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += mpc624.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += multiq3.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_6527.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_65xx.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_660x.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_670x.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_at_a2150.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_at_ao.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_atmio16d.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_atmio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_labpc.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_pcidio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_pcimio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_tiocmd.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ni_tio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl711.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl724.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl725.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl726.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl730.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl812.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl816.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcl818.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcm3724.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcm3730.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcmad.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcmda12.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcmmio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += pcmuio.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += poc.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += rtd520.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += rti800.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += rti802.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += s526.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += s626.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += serial2002.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += skel.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += ssv_dnp.o -obj-$(CONFIG_COMEDI_PCI_DRIVERS) += unioxx5.o +obj-$(CONFIG_COMEDI_ADDI_APCI_035) += addi_apci_035.o +obj-$(CONFIG_COMEDI_ADDI_APCI_1032) += addi_apci_1032.o +obj-$(CONFIG_COMEDI_ADDI_APCI_1500) += addi_apci_1500.o +obj-$(CONFIG_COMEDI_ADDI_APCI_1516) += addi_apci_1516.o +obj-$(CONFIG_COMEDI_ADDI_APCI_1564) += addi_apci_1564.o +obj-$(CONFIG_COMEDI_ADDI_APCI_16XX) += addi_apci_16xx.o +obj-$(CONFIG_COMEDI_ADDI_APCI_2016) += addi_apci_2016.o +obj-$(CONFIG_COMEDI_ADDI_APCI_2032) += addi_apci_2032.o +obj-$(CONFIG_COMEDI_ADDI_APCI_2200) += addi_apci_2200.o +obj-$(CONFIG_COMEDI_ADDI_APCI_3001) += addi_apci_3001.o +obj-$(CONFIG_COMEDI_ADDI_APCI_3120) += addi_apci_3120.o +obj-$(CONFIG_COMEDI_ADDI_APCI_3501) += addi_apci_3501.o +obj-$(CONFIG_COMEDI_ADDI_APCI_3XXX) += addi_apci_3xxx.o +obj-$(CONFIG_COMEDI_ADL_PCI6208) += adl_pci6208.o +obj-$(CONFIG_COMEDI_ADL_PCI7296) += adl_pci7296.o +obj-$(CONFIG_COMEDI_ADL_PCI7432) += adl_pci7432.o +obj-$(CONFIG_COMEDI_ADL_PCI8164) += adl_pci8164.o +obj-$(CONFIG_COMEDI_ADL_PCI9111) += adl_pci9111.o +obj-$(CONFIG_COMEDI_ADL_PCI9118) += adl_pci9118.o +obj-$(CONFIG_COMEDI_ADV_PCI1710) += adv_pci1710.o +obj-$(CONFIG_COMEDI_ADV_PCI1723) += adv_pci1723.o +obj-$(CONFIG_COMEDI_ADV_PCI_DIO) += adv_pci_dio.o +obj-$(CONFIG_COMEDI_AMPLC_DIO200) += amplc_dio200.o +obj-$(CONFIG_COMEDI_AMPLC_PC236) += amplc_pc236.o +obj-$(CONFIG_COMEDI_AMPLC_PC263) += amplc_pc263.o +obj-$(CONFIG_COMEDI_AMPLC_PCI224) += amplc_pci224.o +obj-$(CONFIG_COMEDI_AMPLC_PCI230) += amplc_pci230.o +obj-$(CONFIG_COMEDI_CONTEC_PCI_DIO) += contec_pci_dio.o +obj-$(CONFIG_COMEDI_DT3000) += dt3000.o +obj-$(CONFIG_COMEDI_UNIOXX5) += unioxx5.o +obj-$(CONFIG_COMEDI_GSC_HPDI) += gsc_hpdi.o +obj-$(CONFIG_COMEDI_ICP_MULTI) += icp_multi.o +obj-$(CONFIG_COMEDI_II_PCI20KC) += ii_pci20kc.o +obj-$(CONFIG_COMEDI_DAQBOARD2000) += daqboard2000.o +obj-$(CONFIG_COMEDI_JR3_PCI) += jr3_pci.o +obj-$(CONFIG_COMEDI_KE_COUNTER) += ke_counter.o +obj-$(CONFIG_COMEDI_CB_PCIDAS64) += cb_pcidas64.o +obj-$(CONFIG_COMEDI_CB_PCIDAS) += cb_pcidas.o +obj-$(CONFIG_COMEDI_CB_PCIDDA) += cb_pcidda.o +obj-$(CONFIG_COMEDI_CB_PCIDIO) += cb_pcidio.o +obj-$(CONFIG_COMEDI_CB_PCIMDAS) += cb_pcimdas.o +obj-$(CONFIG_COMEDI_CB_PCIMDDA) += cb_pcimdda.o +obj-$(CONFIG_COMEDI_ME4000) += me4000.o +obj-$(CONFIG_COMEDI_ME_DAQ) += me_daq.o +obj-$(CONFIG_COMEDI_NI_6527) += ni_6527.o +obj-$(CONFIG_COMEDI_NI_65XX) += ni_65xx.o +obj-$(CONFIG_COMEDI_NI_660X) += ni_660x.o +obj-$(CONFIG_COMEDI_NI_670X) += ni_670x.o +obj-$(CONFIG_COMEDI_NI_PCIDIO) += ni_pcidio.o +obj-$(CONFIG_COMEDI_NI_PCIMIO) += ni_pcimio.o +obj-$(CONFIG_COMEDI_RTD520) += rtd520.o +obj-$(CONFIG_COMEDI_S526) += s526.o +obj-$(CONFIG_COMEDI_S626) += s626.o +obj-$(CONFIG_COMEDI_SSV_DNP) += ssv_dnp.o # Comedi PCMCIA drivers -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += cb_das16_cs.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += das08_cs.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += ni_daq_700.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += ni_daq_dio24.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += ni_labpc_cs.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += ni_mio_cs.o -obj-$(CONFIG_COMEDI_PCMCIA_DRIVERS) += quatech_daqp_cs.o +obj-$(CONFIG_COMEDI_CB_DAS16_CS) += cb_das16_cs.o +obj-$(CONFIG_COMEDI_DAS08_CS) += das08_cs.o +obj-$(CONFIG_COMEDI_NI_DAQ_700_CS) += ni_daq_700.o +obj-$(CONFIG_COMEDI_NI_DAQ_DIO24_CS) += ni_daq_dio24.o +obj-$(CONFIG_COMEDI_NI_LABPC_CS) += ni_labpc_cs.o +obj-$(CONFIG_COMEDI_NI_MIO_CS) += ni_mio_cs.o +obj-$(CONFIG_COMEDI_QUATECH_DAQP_CS) += quatech_daqp_cs.o # Comedi USB drivers -obj-$(CONFIG_COMEDI_USB_DRIVERS) += dt9812.o -obj-$(CONFIG_COMEDI_USB_DRIVERS) += usbdux.o -obj-$(CONFIG_COMEDI_USB_DRIVERS) += usbduxfast.o -obj-$(CONFIG_COMEDI_USB_DRIVERS) += vmk80xx.o +obj-$(CONFIG_COMEDI_DT9812) += dt9812.o +obj-$(CONFIG_COMEDI_USBDUX) += usbdux.o +obj-$(CONFIG_COMEDI_USBDUXFAST) += usbduxfast.o +obj-$(CONFIG_COMEDI_VMK80XX) += vmk80xx.o + +# Comedi NI drivers +obj-$(CONFIG_COMEDI_MITE) += mite.o +obj-$(CONFIG_COMEDI_NI_TIO) += ni_tio.o +obj-$(CONFIG_COMEDI_NI_TIO) += ni_tiocmd.o +obj-$(CONFIG_COMEDI_NI_LABPC) += ni_labpc.o +obj-$(CONFIG_COMEDI_FC) += comedi_fc.o diff --git a/drivers/staging/comedi/kcomedilib/Makefile b/drivers/staging/comedi/kcomedilib/Makefile index ffcc9ad..afac6fe 100644 --- a/drivers/staging/comedi/kcomedilib/Makefile +++ b/drivers/staging/comedi/kcomedilib/Makefile @@ -1,4 +1,4 @@ -obj-$(CONFIG_COMEDI) += kcomedilib.o +obj-$(CONFIG_COMEDI_KCOMEDILIB) += kcomedilib.o kcomedilib-objs := \ data.o \ -- 1.7.1 _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/devel
