Re: [PATCH v2] hwmon: (pmbus) Add support for MPS MP2949A

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,Guenter
    Thanks for the review. It all sounds reasonable. I'll address it all in v3.
Best regards,
Ainux Wang.


On Sat, 19 Jun 2021 at 03:39, Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>
> On Fri, Jun 18, 2021 at 11:09:34AM +0800, ainux.wang@xxxxxxxxx wrote:
> > From: "Ainux.Wang" <ainux.wang@xxxxxxxxx>
> >
> > Add support for MP2949A device from Monolithic Power Systems, Inc. (MPS).
> > This is a triple-loop, digital, multi-phase controller.
> > This device:
> > - Supports up to three power rail.
> > - Provides 6 pulse-width modulations (PWMs), and can be configured up
> >   to 6-phase operation for Rail A , up to 2-phase operation for Rail B
> >   and up to 1-phase operation for Rail C.
> > - The PMBus registers are distributed into three pages: Page 0, Page 1,
> >   Page 2. Page 0 contains the registers for Rail A and most of the common
> >   settings for all of the rails. Page 1 contains register information for
> >   Rail B. Page 2 contains register information for Rail C.
> > - The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> >   IMVP9 with only one DAC for each rail to generate REF.
> >
> > Signed-off-by: Ainux.Wang <ainux.wang@xxxxxxxxx>
> > ---
>
> Change log goes here. My normal response to patches with missing change log is:
>
> <Formletter>
> Change log goes here. If it is missing, I won't know what changed.
> That means I will have to dig out older patch versions to compare.
> That costs time and would hold up both this patch as well as all other
> patches which I still have to review.
>
> For this reason, I will not review patches without change log.
> </Formletter>
>
> so you are lucky that your previous version is recent enough that I remember
> at least some of it. However, please do provide change logs in the future.
>
> >  Documentation/hwmon/index.rst   |   1 +
> >  Documentation/hwmon/mp2949a.rst |  44 ++++++++++++
> >  drivers/hwmon/pmbus/Kconfig     |   9 +++
> >  drivers/hwmon/pmbus/Makefile    |   1 +
> >  drivers/hwmon/pmbus/mp2949a.c   | 119 ++++++++++++++++++++++++++++++++
> >  5 files changed, 174 insertions(+)
> >  create mode 100644 Documentation/hwmon/mp2949a.rst
> >  create mode 100644 drivers/hwmon/pmbus/mp2949a.c
> >
> > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> > index 9ed60fa84cbe..56aac3b1678d 100644
> > --- a/Documentation/hwmon/index.rst
> > +++ b/Documentation/hwmon/index.rst
> > @@ -137,6 +137,7 @@ Hardware Monitoring Kernel Drivers
> >     mcp3021
> >     menf21bmc
> >     mlxreg-fan
> > +   mp2949a
> >     mp2975
> >     nct6683
> >     nct6775
> > diff --git a/Documentation/hwmon/mp2949a.rst b/Documentation/hwmon/mp2949a.rst
> > new file mode 100644
> > index 000000000000..ac4084e067f1
> > --- /dev/null
> > +++ b/Documentation/hwmon/mp2949a.rst
> > @@ -0,0 +1,44 @@
> > +.. SPDX-License-Identifier: GPL-2.0
> > +
> > +Kernel driver mp2949a
> > +====================
> > +
> > +Supported chips:
> > +
> > +  * MPS MP2949A
> > +
> > +    Prefix: 'mp2949a'
> > +
> > +Author:
> > +
> > +     Ainux Wang <ainux.wang@xxxxxxxxx>
> > +
> > +Description
> > +-----------
> > +
> > +This driver implements support for Monolithic Power Systems, Inc. (MPS)
> > +triple-loop, digital, multi-phase controller MP2949A.
> > +
> > +This device:
> > +
> > +- Supports up to three power rail.
>
> rails
>
> > +- Provides 6 pulse-width modulations (PWMs), and can be configured up
>
> can be configured for ...
>
> > +  to 6-phase operation for Rail A , up to 2-phase operation for Rail B
>
> Rail B,
>
> > +  and up to 1-phase operation for Rail C.
> > +- The PMBus registers are distributed into three pages: Page 0, Page 1,
> > +  Page 2. Page 0 contains the registers for Rail A and most of the common
> > +  settings for all of the rails. Page 1 contains register information for
> > +  Rail B. Page 2 contains register information for Rail C.
> > +- The MP2949A supports both 5mV VID step and 10mv VID step for IMVP8 and
> > +  IMVP9 with only one DAC for each rail to generate REF.
>
> Please explain REF.
>
> > +
> > +Device supports:
> > +
> > +- SVID interface.
> > +- PMBus rev 1.2 interface.
> > +
> > +Device supports direct format for reading output power.
> > +Device supports linear format for reading input voltage and output current
>
> input voltage, output current, and temperature.
>
> > +and temperature.
> > +Device supports VID for reading output voltage.
> > +The below VID modes are supported: VR12, VR13, IMVP8, IMVP9.
>
> The following
>
> > diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> > index 37a5c39784fa..b1344b265976 100644
> > --- a/drivers/hwmon/pmbus/Kconfig
> > +++ b/drivers/hwmon/pmbus/Kconfig
> > @@ -248,6 +248,15 @@ config SENSORS_MAX8688
> >         This driver can also be built as a module. If so, the module will
> >         be called max8688.
> >
> > +config SENSORS_MP2949A
> > +     tristate "MPS MP2949A"
> > +     help
> > +       If you say yes here you get hardware monitoring support for MPS
> > +       MP2949A Triple Loop Digital Multi-Phase Controller.
> > +
> > +       This driver can also be built as a module. If so, the module will
> > +       be called mp2949a.
> > +
> >  config SENSORS_MP2975
> >       tristate "MPS MP2975"
> >       help
> > diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
> > index f8dcc27cd56a..bfb55ab12da1 100644
> > --- a/drivers/hwmon/pmbus/Makefile
> > +++ b/drivers/hwmon/pmbus/Makefile
> > @@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_MAX20751)      += max20751.o
> >  obj-$(CONFIG_SENSORS_MAX31785)       += max31785.o
> >  obj-$(CONFIG_SENSORS_MAX34440)       += max34440.o
> >  obj-$(CONFIG_SENSORS_MAX8688)        += max8688.o
> > +obj-$(CONFIG_SENSORS_MP2949A)        += mp2949a.o
> >  obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
> >  obj-$(CONFIG_SENSORS_PM6764TR)       += pm6764tr.o
> >  obj-$(CONFIG_SENSORS_PXE1610)        += pxe1610.o
> > diff --git a/drivers/hwmon/pmbus/mp2949a.c b/drivers/hwmon/pmbus/mp2949a.c
> > new file mode 100644
> > index 000000000000..d68e8526abe3
> > --- /dev/null
> > +++ b/drivers/hwmon/pmbus/mp2949a.c
> > @@ -0,0 +1,119 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Hardware monitoring driver for Monolithic Power Systems MP2949A
> > + *
> > + * Copyright (c) 2021 Lemote Technologies. All rights reserved.
> > + * Copyright (c) 2021 Ainux <ainux.wang@xxxxxxxxx>
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/init.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include "pmbus.h"
> > +
> > +#define MP2949A_PAGE_NUM             3
> > +
> > +static int mp2949a_read_byte_data(struct i2c_client *client, int page, int reg)
> > +{
> > +     switch (reg) {
> > +     case PMBUS_VOUT_MODE:
> > +             /* This chip do not support the VOUT_MODE command. */
>
> s/do/does/
>
> This warrants a more detailed explanation: What happens if the command
> is sent to the chip, and why is it not possible to rely on the standard
> response to unsupported commands ?
>
> > +             return -EINVAL;
> > +     default:
> > +             return -ENODATA;
> > +     }
> > +}
> > +
> > +static int mp2949a_identify(struct i2c_client *client,
> > +                         struct pmbus_driver_info *info)
> > +{
> > +     u8 vout_params;
> > +     int i, ret;
> > +
> > +     for (i = 0; i < MP2949A_PAGE_NUM; i++) {
> > +             /* Read the register with VOUT scaling value.*/
> > +             ret = pmbus_read_byte_data(client, i, PMBUS_VOUT_MODE);
>                                                       ^^^^^^^^^^^^^^^
> Should this be MFR_VR_CONFIG ?
>
> > +             if (ret < 0)
> > +                     return ret;
> > +
> > +             /*
> > +              * Rail A bit 5, Rail B bit 4, Rail C bit 3.
> > +              * 1'b1: 5mV  (vr12/imvp8)
> > +              * 1'b0: 10mv (imvp9)
> > +              */
> > +             vout_params = ret & ~BIT(5-i);
>
> space before and after '-'. vout_params is really unnecessary; just do
> the check directly in the if() statement.
>
> > +             if (vout_params)
> > +                     info->vrm_version[i] = vr12;
> > +             else
> > +                     info->vrm_version[i] = imvp9;
> > +
>
> Unnecessary empty line.
>
> checkpatch --strict reports this and the above problem, plus another
> alignment problem. Please fix everything it reports.
>
> > +     }
> > +
> > +     return 0;
> > +}
> > +
> > +static struct pmbus_driver_info mp2949a_info = {
> > +     .pages = MP2949A_PAGE_NUM,
> > +     .format[PSC_VOLTAGE_IN] = linear,
> > +     .format[PSC_VOLTAGE_OUT] = vid,
> > +     .format[PSC_CURRENT_OUT] = linear,
> > +     .format[PSC_TEMPERATURE] = linear,
> > +     .format[PSC_POWER] = direct,
> > +     .m[PSC_POWER] = 1,
> > +     .b[PSC_POWER] = 0,
> > +     .R[PSC_POWER] = 0,
> > +     .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > +             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > +             PMBUS_HAVE_TEMP | PMBUS_HAVE_POUT,
> > +     .func[1] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > +             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > +             PMBUS_HAVE_POUT,
> > +     .func[2] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> > +             PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> > +             PMBUS_HAVE_POUT,
> > +     .identify = mp2949a_identify,
> > +     .read_byte_data = mp2949a_read_byte_data,
> > +};
> > +
> > +static int mp2949a_probe(struct i2c_client *client,
> > +                       const struct i2c_device_id *id)
> > +{
> > +     struct pmbus_driver_info *info;
> > +
> > +     info = devm_kmemdup(&client->dev, &mp2949a_info, sizeof(*info),
> > +                         GFP_KERNEL);
> > +     if (!info)
> > +             return -ENOMEM;
> > +
> > +     return pmbus_do_probe(client, info);
> > +}
> > +
> > +static const struct i2c_device_id mp2949a_id[] = {
> > +     {"mp2949a", 0},
> > +     {}
> > +};
> > +
> > +MODULE_DEVICE_TABLE(i2c, mp2949a_id);
> > +
> > +static const struct of_device_id mp2949a_of_match[] = {
> > +     {.compatible = "mps,mp2949a"},
> > +     {}
> > +};
> > +MODULE_DEVICE_TABLE(of, mp2949a_of_match);
> > +
> > +static struct i2c_driver mp2949a_driver = {
> > +     .driver = {
> > +             .name = "mp2949a",
> > +             .of_match_table = of_match_ptr(mp2949a_of_match),
> > +     },
> > +     .probe = mp2949a_probe,
> > +     .id_table = mp2949a_id,
> > +};
> > +
> > +module_i2c_driver(mp2949a_driver);
> > +
> > +MODULE_AUTHOR("Ainux <ainux.wang@xxxxxxxxx>");
> > +MODULE_DESCRIPTION("PMBus driver for Monolithic Power Systems MP2949A");
> > +MODULE_LICENSE("GPL");
> > --
> > 2.18.1
> >




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux