Re: [PATCH v5 02/16] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi everyone,

On Fri 15 Jan 21, 21:01, Paul Kocialkowski wrote:
> As some D-PHY controllers support both Rx and Tx mode, we need a way for
> users to explicitly request one or the other. For instance, Rx mode can
> be used along with MIPI CSI-2 while Tx mode can be used with MIPI DSI.
> 
> Introduce new MIPI D-PHY PHY submodes to use with PHY_MODE_MIPI_DPHY.
> The default (zero value) is kept to Tx so only the rkisp1 driver, which
> uses D-PHY in Rx mode, needs to be adapted.

I think it was Laurent who brought up on IRC that using a submode is probably
not a correct way to distinguish between Rx and Tx modes.

Thinking about it again, it feels like selecting the direction at run-time
would only be relevant if there's D-PHY hardware than can do both Tx and Rx
*and* that can be muxed to either a MIPI DSI and a CSI-2 controller at
run-time.

For the Allwinner case, the D-PHY is the same hardware for both but there will
be one instance attached to each controller, not a single shared instance.
It feels rather unlikely that a device with both MIPI DSI and CSI-2 would only
have one PHY for the two as this wouldn't allow concurrent use of the two
controllers. Even in a case where there'd be n controllers and m < n
bi-directional PHYs, it feels safe to assume that a static attribution would
be sufficient.
 
As a result it feels more relevant to have this distinction in device-tree
rather than via the PHY API.

What do you think?
Any suggestion on how this should be represented in device-tree?

Cheers,

Paul

> Signed-off-by: Paul Kocialkowski <paul.kocialkowski@xxxxxxxxxxx>
> Acked-by: Helen Koike <helen.koike@xxxxxxxxxxxxx>
> ---
>  drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c |  3 ++-
>  include/linux/phy/phy-mipi-dphy.h                   | 13 +++++++++++++
>  2 files changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 2e5b57e3aedc..cab261644102 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -948,7 +948,8 @@ static int rkisp1_mipi_csi2_start(struct rkisp1_isp *isp,
>  
>  	phy_mipi_dphy_get_default_config(pixel_clock, isp->sink_fmt->bus_width,
>  					 sensor->lanes, cfg);
> -	phy_set_mode(sensor->dphy, PHY_MODE_MIPI_DPHY);
> +	phy_set_mode_ext(cdev->dphy, PHY_MODE_MIPI_DPHY,
> +			 PHY_MIPI_DPHY_SUBMODE_RX);
>  	phy_configure(sensor->dphy, &opts);
>  	phy_power_on(sensor->dphy);
>  
> diff --git a/include/linux/phy/phy-mipi-dphy.h b/include/linux/phy/phy-mipi-dphy.h
> index a877ffee845d..0f57ef46a8b5 100644
> --- a/include/linux/phy/phy-mipi-dphy.h
> +++ b/include/linux/phy/phy-mipi-dphy.h
> @@ -6,6 +6,19 @@
>  #ifndef __PHY_MIPI_DPHY_H_
>  #define __PHY_MIPI_DPHY_H_
>  
> +/**
> + * enum phy_mipi_dphy_submode - MIPI D-PHY sub-mode
> + *
> + * A MIPI D-PHY can be used to transmit or receive data.
> + * Since some controllers can support both, the direction to enable is specified
> + * with the PHY sub-mode. Transmit is assumed by default with phy_set_mode.
> + */
> +
> +enum phy_mipi_dphy_submode {
> +	PHY_MIPI_DPHY_SUBMODE_TX = 0,
> +	PHY_MIPI_DPHY_SUBMODE_RX,
> +};
> +
>  /**
>   * struct phy_configure_opts_mipi_dphy - MIPI D-PHY configuration set
>   *
> -- 
> 2.30.0
> 

-- 
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux