This patch adds a hwmon driver for the SHT4x Temperature and
Humidity sensor.
Signed-off-by: Navin Sankar Velliangiri <navin@xxxxxxxxxxx>
---
Changes in v2:
* Removed unused macro SHT4X_MIN_POLL_INTERVAL
* Replaced time_after instead of ktime_after
* Used goto statements for error handling
* Hardcorded the interval_time instead of clamp_val().
Changes in v3:
* Accept the poll interval if it is greater than SHT4X_MIN_POLL_INTERVAL and
return -EINVAL for negative values & less than SHT4X_MIN_POLL_INTERVAL.
* Changed the data type of update_interval and last_upadated to long.
Changes in v4:
* "update interval" is long but msecs_to_jiffies() accepts only unsigned int.
clamp_val() api is used to assign the update_interval stays within UINT_MAX.
Documentation/hwmon/index.rst | 1 +
Documentation/hwmon/sht4x.rst | 45 +++++
drivers/hwmon/Kconfig | 13 +-
drivers/hwmon/Makefile | 1 +
drivers/hwmon/sht4x.c | 305 ++++++++++++++++++++++++++++++++++
5 files changed, 364 insertions(+), 1 deletion(-)
create mode 100644 Documentation/hwmon/sht4x.rst
create mode 100644 drivers/hwmon/sht4x.c
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 8d5a2df1ecb6..2a20c6616e21 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -160,6 +160,7 @@ Hardware Monitoring Kernel Drivers
sht15
sht21
sht3x
+ sht4x
shtc1
sis5595
sl28cpld
diff --git a/Documentation/hwmon/sht4x.rst b/Documentation/hwmon/sht4x.rst
new file mode 100644
index 000000000000..3b37abcd4a46
--- /dev/null
+++ b/Documentation/hwmon/sht4x.rst
@@ -0,0 +1,45 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver sht4x
+===================
+
+Supported Chips:
+
+ * Sensirion SHT4X
+
+ Prefix: 'sht4x'
+
+ Addresses scanned: None
+
+ Datasheet:
+
+ English: https://www.sensirion.com/fileadmin/user_upload/customers/sensirion/Dokumente/2_Humidity_Sensors/Datasheets/Sensirion_Humidity_Sensors_SHT4x_Datasheet.pdf
+
+Author: Navin Sankar Velliangiri <navin@xxxxxxxxxxx>
+
+
+Description
+-----------
+
+This driver implements support for the Sensirion SHT4x chip, a humidity
+and temperature sensor. Temperature is measured in degree celsius, relative
+humidity is expressed as a percentage. In sysfs interface, all values are
+scaled by 1000, i.e. the value for 31.5 degrees celsius is 31500.
+
+Usage Notes
+-----------
+
+The device communicates with the I2C protocol. Sensors can have the I2C
+address 0x44. See Documentation/i2c/instantiating-devices.rst for methods
+to instantiate the device.
+
+Sysfs entries
+-------------
+
+=============== ============================================
+temp1_input Measured temperature in millidegrees Celcius
+humidity1_input Measured humidity in %H
+update_interval The minimum interval for polling the sensor,
+ in milliseconds. Writable. Must be at least
+ 2000.
+============== =============================================
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 54f04e61fb83..ad10469d7b13 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -1583,6 +1583,17 @@ config SENSORS_SHT3x
This driver can also be built as a module. If so, the module
will be called sht3x.
+config SENSORS_SHT4x
+ tristate "Sensiron humidity and temperature sensors. SHT4x and compat."
+ depends on I2C
+ select CRC8
+ help
+ If you say yes here you get support for thr Sensiron SHT40, SHT41 and
+ SHT45 humidity and temperature sensors.
+
+ This driver can also be built as a module. If so, the module
+ will be called sht4x.
+
config SENSORS_SHTC1
tristate "Sensiron humidity and temperature sensors. SHTC1 and compat."
depends on I2C
@@ -1798,7 +1809,7 @@ config SENSORS_ADS7871
config SENSORS_AMC6821
tristate "Texas Instruments AMC6821"
- depends on I2C
+ depends on I2C
help
If you say yes here you get support for the Texas Instruments
AMC6821 hardware monitoring chips.
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index fe38e8a5c979..62cee3e03c7f 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -170,6 +170,7 @@ obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o
obj-$(CONFIG_SENSORS_SHT15) += sht15.o
obj-$(CONFIG_SENSORS_SHT21) += sht21.o
obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o
+obj-$(CONFIG_SENSORS_SHT4x) += sht4x.o
obj-$(CONFIG_SENSORS_SHTC1) += shtc1.o
obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o
obj-$(CONFIG_SENSORS_SMM665) += smm665.o
diff --git a/drivers/hwmon/sht4x.c b/drivers/hwmon/sht4x.c
new file mode 100644
index 000000000000..e33a0ba3aaed
--- /dev/null
+++ b/drivers/hwmon/sht4x.c
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/*
+ * Copyright (c) Linumiz 2021
+ *
+ * sht4x.c - Linux hwmon driver for SHT4x Temperature and Humidity sensor
+ *
+ * Author: Navin Sankar Velliangiri <navin@xxxxxxxxxxx>
+ */
+
+#include <linux/crc8.h>
+#include <linux/delay.h>
+#include <linux/hwmon.h>
+#include <linux/i2c.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/ktime.h>
+
+/*
+ * Poll intervals (in milliseconds)
+ */
+#define SHT4X_MIN_POLL_INTERVAL 2000
+
+/*
+ * I2C command delays (in microseconds)
+ */
+#define SHT4X_MEAS_DELAY 1000
+#define SHT4X_DELAY_EXTRA 10000
+
+/*
+ * Command Bytes
+ */
+#define SHT4X_CMD_MEASURE_HPM 0b11111101
+#define SHT4X_CMD_RESET 0b10010100
+
+#define SHT4X_CMD_LEN 1
+#define SHT4X_CRC8_LEN 1
+#define SHT4X_WORD_LEN 2
+#define SHT4X_RESPONSE_LENGTH 6
+#define SHT4X_CRC8_POLYNOMIAL 0x31
+#define SHT4X_CRC8_INIT 0xff
+#define SHT4X_MIN_TEMPERATURE -45000
+#define SHT4X_MAX_TEMPERATURE 125000
+#define SHT4X_MIN_HUMIDITY 0
+#define SHT4X_MAX_HUMIDITY 100000
+
+DECLARE_CRC8_TABLE(sht4x_crc8_table);
+
+/**
+ * struct sht4x_data - All the data required to operate an SHT4X chip
+ * @client: the i2c client associated with the SHT4X
+ * @lock: a mutex that is used to prevent parallel access to the i2c client
+ * @update_interval: the minimum poll interval
+ * @last_updated: the previous time that the SHT4X was polled
+ * @temperature: the latest temperature value received from the SHT4X
+ * @humidity: the latest humidity value received from the SHT4X
+ */
+struct sht4x_data {
+ struct i2c_client *client;
+ struct mutex lock; /* atomic read data updates */
+ bool valid; /* validity of fields below */
+ long update_interval; /* in milli-seconds */
+ long last_updated; /* in jiffies */
+ s32 temperature;
+ s32 humidity;
+};
+
+/**
+ * sht4x_read_values() - read and parse the raw data from the SHT4X
+ * @sht4x_data: the struct sht4x_data to use for the lock
+ * Return: 0 if succesfull, 1 if not
+ */
+static int sht4x_read_values(struct sht4x_data *data)
+{
+ int ret;
+ u16 t_ticks, rh_ticks;
+ unsigned long next_update;
+ struct i2c_client *client = data->client;
+ u8 crc, raw_data[SHT4X_RESPONSE_LENGTH],
+ cmd[] = {SHT4X_CMD_MEASURE_HPM};
+
+ mutex_lock(&data->lock);
+ next_update = data->last_updated +
+ msecs_to_jiffies(data->update_interval);
+ if (!data->valid || time_after(jiffies, next_update)) {
+ ret = i2c_master_send(client, cmd, SHT4X_CMD_LEN);
+ if (ret < 0)
+ goto unlock;
+
+ usleep_range(SHT4X_MEAS_DELAY,
+ SHT4X_MEAS_DELAY + SHT4X_DELAY_EXTRA);
+
+ ret = i2c_master_recv(client, raw_data, SHT4X_RESPONSE_LENGTH);
+ if (ret != SHT4X_RESPONSE_LENGTH) {
+ if (ret >= 0)
+ ret = -ENODATA;
+
+ goto unlock;
+ }
+
+ t_ticks = raw_data[0] << 8 | raw_data[1];
+ rh_ticks = raw_data[3] << 8 | raw_data[4];
+
+ crc = crc8(sht4x_crc8_table, &raw_data[0], SHT4X_WORD_LEN, CRC8_INIT_VALUE);
+ if (crc != raw_data[2]) {
+ dev_err(&client->dev, "data integrity check failed\n");
+ ret = -EIO;
+ goto unlock;
+ }
+
+ crc = crc8(sht4x_crc8_table, &raw_data[3], SHT4X_WORD_LEN, CRC8_INIT_VALUE);
+ if (crc != raw_data[5]) {
+ dev_err(&client->dev, "data integrity check failed\n");
+ ret = -EIO;
+ goto unlock;
+ }
+
+ data->temperature = ((21875 * (int32_t)t_ticks) >> 13) - 45000;
+ data->humidity = ((15625 * (int32_t)rh_ticks) >> 13) - 6000;
+ data->last_updated = jiffies;
+ data->valid = true;
+ }
+
+unlock:
+ mutex_unlock(&data->lock);
+ return ret;
+}
+
+static ssize_t sht4x_interval_write(struct sht4x_data *data,
+ long val)
+{
+ if (val >= SHT4X_MIN_POLL_INTERVAL)
+ data->update_interval = val;
+ else
+ return -EINVAL;
+
+ return 0;
+}
+
+/**
+ * sht4x_interval_read() - read the minimum poll interval
+ * in milliseconds
+ */
+static size_t sht4x_interval_read(struct sht4x_data *data,
+ long *val)
+{
+ *val = data->update_interval;
+ return 0;
+}
+
+/**
+ * sht4x_temperature1_read() - read the temperature in millidegrees
+ */
+static int sht4x_temperature1_read(struct sht4x_data *data, long *val)
+{
+ int ret;
+
+ ret = sht4x_read_values(data);
+ if (ret < 0)
+ return ret;
+
+ *val = data->temperature;
+
+ return 0;
+}
+
+/**
+ * sht4x_humidity1_read() - read a relative humidity in millipercent
+ */
+static int sht4x_humidity1_read(struct sht4x_data *data, long *val)
+{
+ int ret;
+
+ ret = sht4x_read_values(data);
+ if (ret < 0)
+ return ret;
+
+ *val = data->humidity;
+
+ return 0;
+}
+
+static umode_t sht4x_hwmon_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ switch (type) {
+ case hwmon_temp:
+ case hwmon_humidity:
+ return 0444;
+ case hwmon_chip:
+ return 0644;
+ default:
+ return 0;
+ }
+}
+
+static int sht4x_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ struct sht4x_data *data = dev_get_drvdata(dev);
+
+ switch (type) {
+ case hwmon_temp:
+ return sht4x_temperature1_read(data, val);
+ case hwmon_humidity:
+ return sht4x_humidity1_read(data, val);
+ case hwmon_chip:
+ return sht4x_interval_read(data, val);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static int sht4x_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long val)
+{
+ struct sht4x_data *data = dev_get_drvdata(dev);
+
+ switch (type) {
+ case hwmon_chip:
+ return sht4x_interval_write(data, val);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static const struct hwmon_channel_info *sht4x_info[] = {
+ HWMON_CHANNEL_INFO(chip, HWMON_C_UPDATE_INTERVAL),
+ HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT),
+ HWMON_CHANNEL_INFO(humidity, HWMON_H_INPUT),
+ NULL,
+};
+
+static const struct hwmon_ops sht4x_hwmon_ops = {
+ .is_visible = sht4x_hwmon_visible,
+ .read = sht4x_hwmon_read,
+ .write = sht4x_hwmon_write,
+};
+
+static const struct hwmon_chip_info sht4x_chip_info = {
+ .ops = &sht4x_hwmon_ops,
+ .info = sht4x_info,
+};
+
+static int sht4x_probe(struct i2c_client *client,
+ const struct i2c_device_id *sht4x_id)
+{
+ struct device *device = &client->dev;
+ struct device *hwmon_dev;
+ struct sht4x_data *data;
+ u8 cmd[] = {SHT4X_CMD_RESET};
+ int ret;
+
+ /*
+ * we require full i2c support since the sht4x uses multi-byte read and
+ * writes as well as multi-byte commands which are not supported by
+ * the smbus protocol
+ */
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
+ return -EOPNOTSUPP;
+
+ data = devm_kzalloc(device, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->update_interval = SHT4X_MIN_POLL_INTERVAL;
+ data->client = client;
+
+ mutex_init(&data->lock);
+
+ crc8_populate_msb(sht4x_crc8_table, SHT4X_CRC8_POLYNOMIAL);
+
+ ret = i2c_master_send(client, cmd, SHT4X_CMD_LEN);
+ if (ret != SHT4X_CMD_LEN)
+ return -EIO;
+
+ hwmon_dev = devm_hwmon_device_register_with_info(device,
+ client->name,
+ data,
+ &sht4x_chip_info,
+ NULL);
+
+ return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static const struct i2c_device_id sht4x_id[] = {
+ { "sht4x", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, sht4x_id);
+
+static struct i2c_driver sht4x_driver = {
+ .driver = {
+ .name = "sht4x",
+ },
+ .probe = sht4x_probe,
+ .id_table = sht4x_id,
+};
+
+module_i2c_driver(sht4x_driver);
+
+MODULE_AUTHOR("Navin Sankar Velliangiri <navin@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("Sensirion SHT4x humidity and temperature sensor driver");
+MODULE_LICENSE("GPL v2");
--
2.31.1
