Change multiple sys/xyz to /sys/xyz Signed-off-by: Mark O'Donovan <shiftee@xxxxxxxxxx> --- Documentation/admin-guide/mm/numaperf.rst | 2 +- Documentation/fb/fbcon.rst | 4 ++-- Documentation/hid/intel-ish-hid.rst | 2 +- Documentation/leds/leds-lm3556.rst | 28 +++++++++++------------ 4 files changed, 18 insertions(+), 18 deletions(-) diff --git a/Documentation/admin-guide/mm/numaperf.rst b/Documentation/admin-guide/mm/numaperf.rst index c2f826409bf0..166697325947 100644 --- a/Documentation/admin-guide/mm/numaperf.rst +++ b/Documentation/admin-guide/mm/numaperf.rst @@ -151,7 +151,7 @@ Each cache level's directory provides its attributes. For example, the following shows a single cache level and the attributes available for software to query:: - # tree sys/devices/system/node/node0/memory_side_cache/ + # tree /sys/devices/system/node/node0/memory_side_cache/ /sys/devices/system/node/node0/memory_side_cache/ |-- index1 | |-- indexing diff --git a/Documentation/fb/fbcon.rst b/Documentation/fb/fbcon.rst index 57f66de2f7e1..212f7003cfba 100644 --- a/Documentation/fb/fbcon.rst +++ b/Documentation/fb/fbcon.rst @@ -207,9 +207,9 @@ Documentation/driver-api/console.rst. To summarize: Echo a value to the bind file that represents the framebuffer console driver. So assuming vtcon1 represents fbcon, then:: - echo 1 > sys/class/vtconsole/vtcon1/bind - attach framebuffer console to + echo 1 > /sys/class/vtconsole/vtcon1/bind - attach framebuffer console to console layer - echo 0 > sys/class/vtconsole/vtcon1/bind - detach framebuffer console from + echo 0 > /sys/class/vtconsole/vtcon1/bind - detach framebuffer console from console layer If fbcon is detached from the console layer, your boot console driver (which is diff --git a/Documentation/hid/intel-ish-hid.rst b/Documentation/hid/intel-ish-hid.rst index f6ce44ff611d..7a851252267a 100644 --- a/Documentation/hid/intel-ish-hid.rst +++ b/Documentation/hid/intel-ish-hid.rst @@ -345,7 +345,7 @@ Documentation/ABI/testing/sysfs-bus-iio for IIO ABIs to user space. To debug ISH, event tracing mechanism is used. To enable debug logs:: echo 1 > /sys/kernel/debug/tracing/events/intel_ish/enable - cat sys/kernel/debug/tracing/trace + cat /sys/kernel/debug/tracing/trace 3.8 ISH IIO sysfs Example on Lenovo thinkpad Yoga 260 ----------------------------------------------------- diff --git a/Documentation/leds/leds-lm3556.rst b/Documentation/leds/leds-lm3556.rst index 1ef17d7d800e..32e3983473ba 100644 --- a/Documentation/leds/leds-lm3556.rst +++ b/Documentation/leds/leds-lm3556.rst @@ -23,7 +23,7 @@ from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A), or by pulling the STROBE pin HIGH. -LM3556 Flash can be controlled through sys/class/leds/flash/brightness file +LM3556 Flash can be controlled through /sys/class/leds/flash/brightness file * if STROBE pin is enabled, below example control brightness only, and ON / OFF will be controlled by STROBE pin. @@ -32,17 +32,17 @@ Flash Example: OFF:: - #echo 0 > sys/class/leds/flash/brightness + #echo 0 > /sys/class/leds/flash/brightness 93.75 mA:: - #echo 1 > sys/class/leds/flash/brightness + #echo 1 > /sys/class/leds/flash/brightness ... 1500 mA:: - #echo 16 > sys/class/leds/flash/brightness + #echo 16 > /sys/class/leds/flash/brightness Torch Mode ^^^^^^^^^^ @@ -51,7 +51,7 @@ In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the hardware TORCH input. -LM3556 torch can be controlled through sys/class/leds/torch/brightness file. +LM3556 torch can be controlled through /sys/class/leds/torch/brightness file. * if TORCH pin is enabled, below example control brightness only, and ON / OFF will be controlled by TORCH pin. @@ -59,22 +59,22 @@ Torch Example: OFF:: - #echo 0 > sys/class/leds/torch/brightness + #echo 0 > /sys/class/leds/torch/brightness 46.88 mA:: - #echo 1 > sys/class/leds/torch/brightness + #echo 1 > /sys/class/leds/torch/brightness ... 375 mA:: - #echo 8 > sys/class/leds/torch/brightness + #echo 8 > /sys/class/leds/torch/brightness Indicator Mode ^^^^^^^^^^^^^^ -Indicator pattern can be set through sys/class/leds/indicator/pattern file, +Indicator pattern can be set through /sys/class/leds/indicator/pattern file, and 4 patterns are pre-defined in indicator_pattern array. According to N-lank, Pulse time and N Period values, different pattern wiill @@ -87,13 +87,13 @@ Indicator pattern example: pattern 0:: - #echo 0 > sys/class/leds/indicator/pattern + #echo 0 > /sys/class/leds/indicator/pattern ... pattern 3:: - #echo 3 > sys/class/leds/indicator/pattern + #echo 3 > /sys/class/leds/indicator/pattern Indicator brightness can be controlled through sys/class/leds/indicator/brightness file. @@ -102,17 +102,17 @@ Example: OFF:: - #echo 0 > sys/class/leds/indicator/brightness + #echo 0 > /sys/class/leds/indicator/brightness 5.86 mA:: - #echo 1 > sys/class/leds/indicator/brightness + #echo 1 > /sys/class/leds/indicator/brightness ... 46.875mA:: - #echo 8 > sys/class/leds/indicator/brightness + #echo 8 > /sys/class/leds/indicator/brightness Notes ----- -- 2.25.1
