- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx>
---
Documentation/networking/cops.rst | 80 ++++++++++++++++++++++++++++++
Documentation/networking/cops.txt | 63 -----------------------
Documentation/networking/index.rst | 1 +
drivers/net/appletalk/Kconfig | 2 +-
4 files changed, 82 insertions(+), 64 deletions(-)
create mode 100644 Documentation/networking/cops.rst
delete mode 100644 Documentation/networking/cops.txt
diff --git a/Documentation/networking/cops.rst b/Documentation/networking/cops.rst
new file mode 100644
index 000000000000..964ba80599a9
--- /dev/null
+++ b/Documentation/networking/cops.rst
@@ -0,0 +1,80 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+========================================
+The COPS LocalTalk Linux driver (cops.c)
+========================================
+
+By Jay Schulist <jschlst@xxxxxxxxx>
+
+This driver has two modes and they are: Dayna mode and Tangent mode.
+Each mode corresponds with the type of card. It has been found
+that there are 2 main types of cards and all other cards are
+the same and just have different names or only have minor differences
+such as more IO ports. As this driver is tested it will
+become more clear exactly what cards are supported.
+
+Right now these cards are known to work with the COPS driver. The
+LT-200 cards work in a somewhat more limited capacity than the
+DL200 cards, which work very well and are in use by many people.
+
+TANGENT driver mode:
+ - Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200
+
+DAYNA driver mode:
+ - Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95,
+ - Farallon PhoneNET PC III, Farallon PhoneNET PC II
+
+Other cards possibly supported mode unknown though:
+ - Dayna DL2000 (Full length)
+
+The COPS driver defaults to using Dayna mode. To change the driver's
+mode if you built a driver with dual support use board_type=1 or
+board_type=2 for Dayna or Tangent with insmod.
+
+Operation/loading of the driver
+===============================
+
+Use modprobe like this: /sbin/modprobe cops.o (IO #) (IRQ #)
+If you do not specify any options the driver will try and use the IO = 0x240,
+IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing.
+
+To load multiple COPS driver Localtalk cards you can do one of the following::
+
+ insmod cops io=0x240 irq=5
+ insmod -o cops2 cops io=0x260 irq=3
+
+Or in lilo.conf put something like this::
+
+ append="ether=5,0x240,lt0 ether=3,0x260,lt1"
+
+Then bring up the interface with ifconfig. It will look something like this::
+
+ lt0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00
+ inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
+ UP BROADCAST RUNNING NOARP MULTICAST MTU:600 Metric:1
+ RX packets:0 errors:0 dropped:0 overruns:0 frame:0
+ TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0
+
+Netatalk Configuration
+======================
+
+You will need to configure atalkd with something like the following to make
+it work with the cops.c driver.
+
+* For single LTalk card use::
+
+ dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033"
+ lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
+
+* For multiple cards, Ethernet and LocalTalk::
+
+ eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033"
+ lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
+
+* For multiple LocalTalk cards, and an Ethernet card.
+
+* Order seems to matter here, Ethernet last::
+
+ lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1"
+ lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2"
+ eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk"
diff --git a/Documentation/networking/cops.txt b/Documentation/networking/cops.txt
deleted file mode 100644
index 3e344b448e07..000000000000
--- a/Documentation/networking/cops.txt
+++ /dev/null
@@ -1,63 +0,0 @@
-Text File for the COPS LocalTalk Linux driver (cops.c).
- By Jay Schulist <jschlst@xxxxxxxxx>
-
-This driver has two modes and they are: Dayna mode and Tangent mode.
-Each mode corresponds with the type of card. It has been found
-that there are 2 main types of cards and all other cards are
-the same and just have different names or only have minor differences
-such as more IO ports. As this driver is tested it will
-become more clear exactly what cards are supported.
-
-Right now these cards are known to work with the COPS driver. The
-LT-200 cards work in a somewhat more limited capacity than the
-DL200 cards, which work very well and are in use by many people.
-
-TANGENT driver mode:
- Tangent ATB-II, Novell NL-1000, Daystar Digital LT-200
-DAYNA driver mode:
- Dayna DL2000/DaynaTalk PC (Half Length), COPS LT-95,
- Farallon PhoneNET PC III, Farallon PhoneNET PC II
-Other cards possibly supported mode unknown though:
- Dayna DL2000 (Full length)
-
-The COPS driver defaults to using Dayna mode. To change the driver's
-mode if you built a driver with dual support use board_type=1 or
-board_type=2 for Dayna or Tangent with insmod.
-
-** Operation/loading of the driver.
-Use modprobe like this: /sbin/modprobe cops.o (IO #) (IRQ #)
-If you do not specify any options the driver will try and use the IO = 0x240,
-IRQ = 5. As of right now I would only use IRQ 5 for the card, if autoprobing.
-
-To load multiple COPS driver Localtalk cards you can do one of the following.
-
-insmod cops io=0x240 irq=5
-insmod -o cops2 cops io=0x260 irq=3
-
-Or in lilo.conf put something like this:
- append="ether=5,0x240,lt0 ether=3,0x260,lt1"
-
-Then bring up the interface with ifconfig. It will look something like this:
-lt0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-F7-00-00-00-00-00-00-00-00
- inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
- UP BROADCAST RUNNING NOARP MULTICAST MTU:600 Metric:1
- RX packets:0 errors:0 dropped:0 overruns:0 frame:0
- TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 coll:0
-
-** Netatalk Configuration
-You will need to configure atalkd with something like the following to make
-it work with the cops.c driver.
-
-* For single LTalk card use.
-dummy -seed -phase 2 -net 2000 -addr 2000.10 -zone "1033"
-lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
-
-* For multiple cards, Ethernet and LocalTalk.
-eth0 -seed -phase 2 -net 3000 -addr 3000.20 -zone "1033"
-lt0 -seed -phase 1 -net 1000 -addr 1000.50 -zone "1033"
-
-* For multiple LocalTalk cards, and an Ethernet card.
-* Order seems to matter here, Ethernet last.
-lt0 -seed -phase 1 -net 1000 -addr 1000.10 -zone "LocalTalk1"
-lt1 -seed -phase 1 -net 2000 -addr 2000.20 -zone "LocalTalk2"
-eth0 -seed -phase 2 -net 3000 -addr 3000.30 -zone "EtherTalk"
diff --git a/Documentation/networking/index.rst b/Documentation/networking/index.rst
index 55802abd65a0..7b596810d479 100644
--- a/Documentation/networking/index.rst
+++ b/Documentation/networking/index.rst
@@ -46,6 +46,7 @@ Contents:
baycom
bonding
cdc_mbim
+ cops
.. only:: subproject and html
diff --git a/drivers/net/appletalk/Kconfig b/drivers/net/appletalk/Kconfig
index af509b05ac5c..d4e51c048f62 100644
--- a/drivers/net/appletalk/Kconfig
+++ b/drivers/net/appletalk/Kconfig
@@ -59,7 +59,7 @@ config COPS
package. This driver is experimental, which means that it may not
work. This driver will only work if you choose "AppleTalk DDP"
networking support, above.
- Please read the file <file:Documentation/networking/cops.txt>.
+ Please read the file <file:Documentation/networking/cops.rst>.
config COPS_DAYNA
bool "Dayna firmware support"
--
2.25.4
