Convert the DPAA2 ethernet driver to use the finalised link parameters in mac_link_up() rather than the parameters in mac_config(), which are more suited to the needs of the DPAA2 MC firmware than those available via mac_config(). Tested-by: Ioana Ciornei <ioana.ciornei@xxxxxxx> Signed-off-by: Russell King <rmk+kernel@xxxxxxxxxxxxxxx> --- .../net/ethernet/freescale/dpaa2/dpaa2-mac.c | 54 +++++++++++-------- .../net/ethernet/freescale/dpaa2/dpaa2-mac.h | 1 + 2 files changed, 33 insertions(+), 22 deletions(-) diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c index 3a75c5b58f95..3ee236c5fc37 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c +++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c @@ -123,35 +123,16 @@ static void dpaa2_mac_config(struct phylink_config *config, unsigned int mode, struct dpmac_link_state *dpmac_state = &mac->state; int err; - if (state->speed != SPEED_UNKNOWN) - dpmac_state->rate = state->speed; - - if (state->duplex != DUPLEX_UNKNOWN) { - if (!state->duplex) - dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX; - else - dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX; - } - if (state->an_enabled) dpmac_state->options |= DPMAC_LINK_OPT_AUTONEG; else dpmac_state->options &= ~DPMAC_LINK_OPT_AUTONEG; - if (state->pause & MLO_PAUSE_RX) - dpmac_state->options |= DPMAC_LINK_OPT_PAUSE; - else - dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE; - - if (!!(state->pause & MLO_PAUSE_RX) ^ !!(state->pause & MLO_PAUSE_TX)) - dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE; - else - dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE; - err = dpmac_set_link_state(mac->mc_io, 0, mac->mc_dev->mc_handle, dpmac_state); if (err) - netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err); + netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n", + __func__, err); } static void dpaa2_mac_link_up(struct phylink_config *config, @@ -165,10 +146,37 @@ static void dpaa2_mac_link_up(struct phylink_config *config, int err; dpmac_state->up = 1; + + if (mac->if_link_type == DPMAC_LINK_TYPE_PHY) { + /* If the DPMAC is configured for PHY mode, we need + * to pass the link parameters to the MC firmware. + */ + dpmac_state->rate = speed; + + if (duplex == DUPLEX_HALF) + dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX; + else if (duplex == DUPLEX_FULL) + dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX; + + /* This is lossy; the firmware really should take the pause + * enablement status rather than pause/asym pause status. + */ + if (rx_pause) + dpmac_state->options |= DPMAC_LINK_OPT_PAUSE; + else + dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE; + + if (rx_pause ^ tx_pause) + dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE; + else + dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE; + } + err = dpmac_set_link_state(mac->mc_io, 0, mac->mc_dev->mc_handle, dpmac_state); if (err) - netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err); + netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n", + __func__, err); } static void dpaa2_mac_link_down(struct phylink_config *config, @@ -241,6 +249,8 @@ int dpaa2_mac_connect(struct dpaa2_mac *mac) goto err_close_dpmac; } + mac->if_link_type = attr.link_type; + dpmac_node = dpaa2_mac_get_node(attr.id); if (!dpmac_node) { netdev_err(net_dev, "No dpmac@%d node found.\n", attr.id); diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h index 4da8079b9155..2130d9c7d40e 100644 --- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h +++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h @@ -20,6 +20,7 @@ struct dpaa2_mac { struct phylink_config phylink_config; struct phylink *phylink; phy_interface_t if_mode; + enum dpmac_link_type if_link_type; }; bool dpaa2_mac_is_type_fixed(struct fsl_mc_device *dpmac_dev, -- 2.20.1