These patches introduce support for the Activity Monitors Unit (AMU)
CPU extension, an optional extension in ARMv8.4 CPUs. This provides
performance counters intended for system management use. Two of these
counters are then used to compute the frequency scale correction
factor needed to achieve frequency invariance.
With the CONFIG_ARM64_AMU_EXTN enabled and lacking the disable_amu
kernel parameter, the kernel is able to safely run a mix of CPUs with
and without support for the AMU extension. The AMU capability is
unconditionally enabled in the kernel as to allow any late CPU to use
the feature: the cpu_enable function will be called for all CPUs that
match the criteria, including secondary and hotplugged CPUs, marking
this feature as present on that respective CPU.
To be noted that firmware must implement AMU support when running on
CPUs that present the activity monitors extension: allow access to
the registers from lower exception levels, enable the counters,
implement save and restore functionality. More details can be found
in the documentation.
Given that the activity counters inform on activity on the CPUs, and
that not all CPUs might implement the extension, for functional and
security reasons, it's best to disable access to the AMU registers
from userspace (EL0) and KVM guests.
In the last patch of the series, two of the AMU counters are used to
compute the frequency scale factor needed to achieve frequency
invariance of signals in the scheduler, based on an interface added
to support counter-based frequency invariance - arch_scale_freq_tick.
The interface and update point for the counter-based frequency scale
factor is based on the similar approach in the patch that introduces
frequency invariance for x86 [1].
The current series is based on tip/sched/core.
Testing:
- Build tested for multiple architectures and defconfigs.
- AMU feature detection, EL0 and KVM guest access to AMU registers,
feature support in firmware (version 1.5 and later of the ARM
Trusted Firmware) was tested on an Armv8-A Base Platform FVP:
Architecture Envelope Model [2] (supports version 8.0 to 8.5),
with the following configurations:
cluster0.has_arm_v8-4=1
cluster1.has_arm_v8-4=1
cluster0.has_amu=1
cluster1.has_amu=1
v2 -> v3:
- v2 can be found at [4]
- [1/7] used cpumask instead of per-cpu variable to flag AMU presence
as; introduced disable_amu kernel parameter; removed ftr_id_pfr0 AMU
bits - recommended by Suzuki.
- [2/7] replaced obscure label as recommended by Valentin.
- [3/7] clarified activate_traps_vhe comment
- [4/7] dropped changes in arm64/cpu-feature-registers.txt; removed
use of variable names - recommended by Suzuki
- previous [5/6] - dropped as [1] as added to tip/sched/core
- [5/7] new patch introduced to cleanly obtain maximum hardware
frequency from cpufreq
- [6/7] (previously [6/6]):
- Removed use of workqueues by limiting the validation work done on
each cpu to the setting of the reference per-cpu counter variables.
This is now called directly from cpu_enable (cpufeature.c). Also,
further CPU, policy and system validation is done in a
late_initcall_sync function - waits for deferred probe work to
finish as well to ensure the maximum frequency is set by either
cpufreq drivers or platform drivers - recommended by Lukasz.
- Improved AMU use detection for CPUs in arch_set_freq_scale -
recommended by Lukasz.
- Properly validated arch_max_freq_scale and added detailed
documentation for how arch_max_freq_scale and freq_scale are
obtained based on counters - recommended by Valentin.
- Overall - limited tight coupling between AMU use and cpufreq
(use of maximum frequency information and policy validation).
- [7/7] introduced patch to warn if arch_timer_rate is too low
- functionality provided by Valentin.
v1 -> v2:
- v1 can be found at [3]
- Added patches that use the counters for the scheduler's frequency
invariance engine
- In patch arm64: add support for the AMU extension v1 -
- Defined an accessor function cpu_has_amu_feat to allow a read
of amu_feat only from the current CPU, to ensure the safe use
of the per-cpu variable for the current user (arm64 topology
driver) and future users.
- Modified type of amu_feat from bool to u8 to satisfy sparse
checker's warning 'expression using sizeof _Bool [sparse]',
as the size of bool is compiler dependent.
[1] https://lore.kernel.org/lkml/20200122151617.531-1-ggherdovich@xxxxxxx/
[2] https://developer.arm.com/tools-and-software/simulation-models/fixed-virtual-platforms
[3] https://lore.kernel.org/lkml/20190917134228.5369-1-ionela.voinescu@xxxxxxx/
[4] https://lore.kernel.org/lkml/20191218182607.21607-1-ionela.voinescu@xxxxxxx/
Ionela Voinescu (6):
arm64: add support for the AMU extension v1
arm64: trap to EL1 accesses to AMU counters from EL0
arm64/kvm: disable access to AMU registers from kvm guests
Documentation: arm64: document support for the AMU extension
cpufreq: add function to get the hardware max frequency
arm64: use activity monitors for frequency invariance
Valentin Schneider (1):
clocksource/drivers/arm_arch_timer: validate arch_timer_rate
.../admin-guide/kernel-parameters.txt | 10 +
Documentation/arm64/amu.rst | 114 +++++++++++
Documentation/arm64/booting.rst | 14 ++
Documentation/arm64/index.rst | 1 +
arch/arm64/Kconfig | 31 +++
arch/arm64/include/asm/assembler.h | 10 +
arch/arm64/include/asm/cpucaps.h | 3 +-
arch/arm64/include/asm/cpufeature.h | 5 +
arch/arm64/include/asm/kvm_arm.h | 1 +
arch/arm64/include/asm/sysreg.h | 38 ++++
arch/arm64/include/asm/topology.h | 16 ++
arch/arm64/kernel/cpufeature.c | 101 ++++++++++
arch/arm64/kernel/topology.c | 185 ++++++++++++++++++
arch/arm64/kvm/hyp/switch.c | 14 +-
arch/arm64/kvm/sys_regs.c | 93 ++++++++-
arch/arm64/mm/proc.S | 3 +
drivers/base/arch_topology.c | 8 +
drivers/clocksource/arm_arch_timer.c | 18 +-
drivers/cpufreq/cpufreq.c | 20 ++
include/linux/cpufreq.h | 5 +
include/linux/topology.h | 7 +
21 files changed, 690 insertions(+), 7 deletions(-)
create mode 100644 Documentation/arm64/amu.rst
base-commit: 25ac227a25ac946e0356772012398cd1710a8bab
--
2.17.1
