Re: [PATCH v2] hwmon: Driver for temperature sensors on SATA drives

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 1/12/20 5:45 AM, Gabriel C wrote:
Am So., 12. Jan. 2020 um 14:07 Uhr schrieb Guenter Roeck <linux@xxxxxxxxxxxx>:

On 1/12/20 4:07 AM, Linus Walleij wrote:
On Sun, Jan 12, 2020 at 1:03 PM Gabriel C <nix.or.die@xxxxxxxxx> wrote:
Am So., 12. Jan. 2020 um 12:22 Uhr schrieb Linus Walleij
<linus.walleij@xxxxxxxxxx>:

On Sun, Jan 12, 2020 at 12:18 PM Gabriel C <nix.or.die@xxxxxxxxx> wrote:

What I've noticed however is the nvme temperature low/high values on
the Sensors X are strange here.
(...)
Sensor 1:     +27.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +29.9°C  (low  = -273.1°C, high = +65261.8°C)
(...)
Sensor 1:     +23.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +25.9°C  (low  = -273.1°C, high = +65261.8°C)

That doesn't look strange to me. It seems like reasonable defaults
from the firmware if either it doesn't really log the min/max temperatures
or hasn't been through a cycle of updating these yet. Just set both
to absolute min/max temperatures possible.

Ok I'll check that.

Do you mean by setting the temperatures to use a lmsensors config?
Or is there a way to set these with a nvme command?

Not that I know of.

The min/max are the minumum and maximum temperatures the
device has experienced during this power-on cycle.


No, that would be lowest/highest. The above are (or should be) per-sensor
setpoints. The default for those is typically the absolute minimum /
maximum of the supported range.

Some SATA drives report the lowest/highest temperatures experienced
since power cycle, like here.

drivetemp-scsi-5-0
Adapter: SCSI adapter
temp1:        +23.0°C  (low  =  +0.0°C, high = +60.0°C)
                         (crit low = -41.0°C, crit = +85.0°C)
                         (lowest = +20.0°C, highest = +31.0°C)


The SATA temperatures are fine and reported like this here too, just
the nvme ones are strange.

drivetemp-scsi-4-0
Adapter: SCSI adapter
temp1:        +28.0°C  (low  =  +1.0°C, high = +61.0°C)
                       (crit low =  +2.0°C, crit = +60.0°C)
                       (lowest = +16.0°C, highest = +31.0°C)

drivetemp-scsi-12-0
Adapter: SCSI adapter
temp1:        +29.0°C  (low  =  +1.0°C, high = +61.0°C)
                       (crit low =  +2.0°C, crit = +60.0°C)
                       (lowest = +18.0°C, highest = +32.0°C)

and so on.

Btw, where I can find the code does these calculations?


Not sure if that is what you are looking for, but the nvme hardware
monitoring driver is at drivers/nvme/host/hwmon.c, the SATA hardware
monitoring driver is at drivers/hwmon/drivetemp.c.

The limits on nvme drives are configurable.

root@server:/sys/class/hwmon# sensors nvme-pci-0100
nvme-pci-0100
Adapter: PCI adapter
Composite:    +40.9°C  (low  = -273.1°C, high = +84.8°C)
                       (crit = +84.8°C)
Sensor 1:     +40.9°C  (low  = -273.1°C, high = +65261.8°C)
Sensor 2:     +43.9°C  (low  = -273.1°C, high = +65261.8°C)

root@server:/sys/class/hwmon# echo 0 > hwmon1/temp2_min
root@server:/sys/class/hwmon# echo 100000 > hwmon1/temp2_max

root@server:/sys/class/hwmon# sensors nvme-pci-0100
nvme-pci-0100
Adapter: PCI adapter
Composite:    +38.9°C  (low  = -273.1°C, high = +84.8°C)
                       (crit = +84.8°C)
Sensor 1:     +38.9°C  (low  =  -0.1°C, high = +99.8°C)
Sensor 2:     +42.9°C  (low  = -273.1°C, high = +65261.8°C)

If you dislike the defaults, just configure whatever you think is
appropriate for your system.

Thanks,
Guenter



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux