ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs, a real-time clock (RTC), 3 GPO/regulator control pins, HALL input and a 32.768 kHz clock gate. Document the dt bindings drivers are using. Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx> --- Changes since v5: - Remove regulator run-level properties - Change SPDX to dual lisence - remove trivial descriptions .../bindings/mfd/rohm,bd71828-pmic.yaml | 193 ++++++++++++++++++ 1 file changed, 193 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml new file mode 100644 index 000000000000..4fbb9e734284 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml @@ -0,0 +1,193 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/rohm,bd71828-pmic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD71828 Power Management Integrated Circuit bindings + +maintainers: + - Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx> + +description: | + BD71828GW is a single-chip power management IC for battery-powered portable + devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA + single-cell linear charger. Also included is a Coulomb counter, a real-time + clock (RTC), and a 32.768 kHz clock gate. + +properties: + compatible: + const: rohm,bd71828 + + reg: + description: + I2C slave address. + maxItems: 1 + + interrupts: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + description: | + The first cell is the pin number and the second cell is used to specify + flags. See ../gpio/gpio.txt for more information. + + clocks: + maxItems: 1 + + "#clock-cells": + const: 0 + + rohm,charger-sense-resistor-ohms: + minimum: 10000000 + maximum: 50000000 + description: | + BD71827 and BD71828 have SAR ADC for measuring charging currents. + External sense resistor (RSENSE in data sheet) should be used. If some + other but 30MOhm resistor is used the resistance value should be given + here in Ohms. + + regulators: + $ref: ../regulator/rohm,bd71828-regulator.yaml + description: + List of child nodes that specify the regulators. + + leds: + $ref: ../leds/rohm,bd71828-leds.yaml + + gpio-reserved-ranges: + description: | + Usage of BD71828 GPIO pins can be changed via OTP. This property can be + used to mark the pins which should not be configured for GPIO. Please see + the ../gpio/gpio.txt for more information. + +required: + - compatible + - reg + - interrupts + - clocks + - "#clock-cells" + - regulators + - gpio-controller + - "#gpio-cells" + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/leds/common.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + pmic: pmic@4b { + compatible = "rohm,bd71828"; + reg = <0x4b>; + + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; + + clocks = <&osc 0>; + #clock-cells = <0>; + clock-output-names = "bd71828-32k-out"; + + gpio-controller; + #gpio-cells = <2>; + gpio-reserved-ranges = <0 1>, <2 1>; + + rohm,charger-sense-resistor-ohms = <10000000>; + + regulators { + buck1: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2000000>; + regulator-ramp-delay = <2500>; + }; + buck2: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2000000>; + regulator-ramp-delay = <2500>; + }; + buck3: BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2000000>; + }; + buck4: BUCK4 { + regulator-name = "buck4"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + }; + buck5: BUCK5 { + regulator-name = "buck5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + }; + buck6: BUCK6 { + regulator-name = "buck6"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2000000>; + regulator-ramp-delay = <2500>; + }; + buck7: BUCK7 { + regulator-name = "buck7"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2000000>; + regulator-ramp-delay = <2500>; + }; + ldo1: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + ldo2: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + ldo3: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + ldo4: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + ldo5: LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + ldo6: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + ldo7_reg: LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + }; + + leds { + compatible = "rohm,bd71828-leds"; + + led-1 { + rohm,led-compatible = "bd71828-grnled"; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_GREEN>; + }; + led-2 { + rohm,led-compatible = "bd71828-ambled"; + function = LED_FUNCTION_CHARGING; + color = <LED_COLOR_ID_AMBER>; + }; + }; + }; + }; -- 2.21.0 -- Matti Vaittinen, Linux device drivers ROHM Semiconductors, Finland SWDC Kiviharjunlenkki 1E 90220 OULU FINLAND ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~ Simon says - in Latin please. ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~ Thanks to Simon Glass for the translation =]
