Re: [PATCH 3/3] dt-bindings: iio: Add ltc2947 documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Sep 24, 2019 at 02:49:45PM +0200, Nuno Sá wrote:
> Document the LTC2947 device devicetree bindings.
> 
> Signed-off-by: Nuno Sá <nuno.sa@xxxxxxxxxx>
> ---
>  .../bindings/hwmon/adi,ltc2947.yaml           | 101 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 102 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml b/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
> new file mode 100644
> index 000000000000..2ea0187421d4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
> @@ -0,0 +1,101 @@

Missing license. Please make new bindings (GPL-2.0-only OR BSD-2-Clause)

> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/bindings/hwmon/adi,ltc2947.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices LTC2947 high precision power and energy monitor
> +
> +maintainers:
> +  - Nuno Sá <nuno.sa@xxxxxxxxxx>
> +
> +description: |
> +  Analog Devices LTC2947 high precision power and energy monitor over SPI or I2C.
> +
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,ltc2947
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    description:
> +      The LTC2947 uses either a trimmed internal oscillator or an external clock
> +      as the time base for determining the integration period to represent time,
> +      charge and energy. When an external clock is used, this property must be
> +      set accordingly.
> +    maxItems: 1
> +
> +  adi,accumulator-ctl-pol:
> +    description:
> +      This property controls the polarity of current that is accumulated to
> +      calculate charge and energy so that, they can be only accumulated for
> +      positive current for example. Since there are two sets of registers for
> +      the accumulated values, this entry can also have two items which sets
> +      energy1/charge1 and energy2/charger2 respectively. Check table 12 of the
> +      datasheet for more information on the supported options.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32-array
> +      - enum: [0, 1, 2, 3]
> +      - minItems: 2
> +      - maxItems: 2
> +    default: [0, 0]

This should be:

allOf:
  - $ref: ...
items:
  enum: [0, 1, 2, 3]
  default: 0
minItems: 2
maxItems: 2

> +
> +  adi,accumulation-deadband-microamp:
> +    description:
> +      This property controls the Accumulation Dead band which allows to set the
> +      level of current below which no accumulation takes place.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - maximum: 255

maximum should be at same indent as allOf. Or default should be at the 
same level as maximum (under a single '-' list entry).

> +    default: 0
> +
> +  adi,gpio-out-pol:
> +    description:
> +      This property controls the GPIO polarity. Setting it to one makes the GPIO
> +      active high, setting it to zero makets it active low. When this property
> +      is present, the GPIO is automatically configured as output and set to
> +      control a fan as a function of measured temperature.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [0, 1]
> +    default: 0

Same here.

> +
> +  adi,gpio-in-accum:
> +    description:
> +      When set, this property sets the GPIO as input. It is then used to control
> +      the accumulation of charge, energy and time. This function can be
> +      enabled/configured separately for each of the two sets of accumulation
> +      registers. Check table 13 of the datasheet for more information on the
> +      supported options. This property cannot be used together with
> +      adi,gpio-out-pol.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32-array
> +      - enum: [0, 1, 2]
> +      - minItems: 2
> +      - maxItems: 2
> +    default: [0, 0]

Similar here.

> +
> +required:
> +  - compatible
> +  - reg
> +
> +
> +examples:
> +  - |
> +    spi0 {

Just 'spi'

> +           #address-cells = <1>;
> +           #size-cells = <0>;
> +
> +           ltc2947_spi: ltc2947@0 {
> +                   compatible = "adi,ltc2947";
> +                   reg = <0>;
> +                   /* accumulation takes place always for energ1/charge1. */
> +                   /* accumulation only on positive current for energy2/charge2. */
> +                   adi,accumulator-ctl-pol = <0 1>;
> +           };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 889f38c1c930..820bdde2044b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -9505,6 +9505,7 @@ F:	drivers/hwmon/ltc2947-core.c
>  F:	drivers/hwmon/ltc2947-spi.c
>  F:	drivers/hwmon/ltc2947-i2c.c
>  F:	drivers/hwmon/ltc2947.h
> +F:	Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml
>  
>  LTC4306 I2C MULTIPLEXER DRIVER
>  M:	Michael Hennerich <michael.hennerich@xxxxxxxxxx>
> -- 
> 2.23.0
> 




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux